OSA's Digital Library

Applied Optics

Applied Optics

APPLICATIONS-CENTERED RESEARCH IN OPTICS

  • Vol. 38, Iss. 1 — Jan. 1, 1999
  • pp: 101–112

Toward subnanometer uncertainty in interferometric length measurements of short gauge blocks

Igor Malinovsky, Alexander Titov, Jorge Augusto Dutra, Hakima Belaïdi, Ricardo dos Santos França, and Carlos Alberto Massone  »View Author Affiliations


Applied Optics, Vol. 38, Issue 1, pp. 101-112 (1999)
http://dx.doi.org/10.1364/AO.38.000101


View Full Text Article

Enhanced HTML    Acrobat PDF (2114 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

A primary-level comparator, with a reproducibility of 0.2 nm and intended for realization of a Systeme International length unit in the range of 1–100 mm, is reported. High-precision differential measurements of phase change on reflection from blocks and end plates are demonstrated. A set of experiments has been developed to measure systematic error associated with nonideal interferometer optics and deviations from flatness of an auxiliary plate. For specially selected high-grade 6-mm blocks, reproducible wringing has been achieved with a random uncertainty in length measurements of 0.1–0.2 nm. Subnanometer wear-off of the blocks as a result of the cleaning has been detected. Under the conditions of reproducible wringing, the accuracy of the length measurements is evaluated to be in the 2–3-nm range for 6-mm blocks.

© 1999 Optical Society of America

OCIS Codes
(120.2650) Instrumentation, measurement, and metrology : Fringe analysis
(120.3180) Instrumentation, measurement, and metrology : Interferometry
(120.3940) Instrumentation, measurement, and metrology : Metrology
(120.6650) Instrumentation, measurement, and metrology : Surface measurements, figure
(120.6660) Instrumentation, measurement, and metrology : Surface measurements, roughness

History
Original Manuscript: November 17, 1997
Revised Manuscript: March 24, 1998
Published: January 1, 1999

Citation
Igor Malinovsky, Alexander Titov, Jorge Augusto Dutra, Hakima Belaïdi, Ricardo dos Santos França, and Carlos Alberto Massone, "Toward subnanometer uncertainty in interferometric length measurements of short gauge blocks," Appl. Opt. 38, 101-112 (1999)
http://www.opticsinfobase.org/ao/abstract.cfm?URI=ao-38-1-101


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. “Documents concerning the new definition of the metre,” Metrologia 19, 163–177 (1984).
  2. B. G. Vaucher, R. Thalmann, H. Baechler, “European comparison of short gauge block measurement by interferometry,” Metrologia 32, 79–86 (1995). [CrossRef]
  3. N. Brown, T. B. Eom, E. Howick, O. Kruger, Y. Lan, S. L. Ling-Tan, H. Matsumoto, J. Pusaka, R. P. Singhal, Y. Xu, “Asian-Pacific metrology programme of gauge blocks comparison,” Metrologia 33, 61–66 (1996). [CrossRef]
  4. H. Darnedde, J. Helmcke, “European comparison of long gauge blocks,” Metrologia 33, 485–491 (1996). [CrossRef]
  5. H. Darnedde, “High-precision calibration of long gauge blocks using the vacuum wavelength comparator,” Metrologia 29, 349–359 (1992). [CrossRef]
  6. L. Abramova, V. Baratov, V. Fedorin, L. Khavinson, E. Latigneva, K. Riski, E. Ikonen, A. Lassila, “Comparison of length standards between the CMA and the VNIIM,” Metrologia 33, 29–33 (1996). [CrossRef]
  7. E. Engelhard, “Precise interferometric measurement of gauge blocks,” in Proceedings of the Symposium on Gauge Blocks, August 1955, Natl. Bur. Stand. Circ.581, 1–20 (1957).
  8. In this paper we use the terms precision (repeatability of the results of the measurements), reproducibility, and accuracy, in this way defining the increasing hierarchy in the measurement results.
  9. If not specifically otherwise defined, the term “uncertainty” is used in the meaning of a random (A-type) uncertainty, or the error of the measurement result without application of any corrections for possible systematic effects.
  10. C. F. Bruce, “The effects of collimation and oblique incidence in length interferometers,” Aust. J. Phys. 8, 224–240 (1955). [CrossRef]
  11. S. Ishikawa, G. Bönch, H. Böhme, “Phase-shifting interferometry with a coupled interferometer: application to optical roughness of gauge blocks,” Optik (Stuttgart) 91, 103–108 (1992).
  12. R. K. Leach, K. Jackson, A. Hart, “Measurement of gauge blocks by interferometry: measurement of the phase change at reflection,” (National Physical Laboratory, Teddington, UK, 1997).
  13. H. Matsumoto, L. Zeng, “Simple compensation method for wringing errors in the interferometric calibration of gauge blocks,” Metrologia 33, 1–4 (1996). [CrossRef]
  14. A. Titov, I. Malinovsky, H. Belaidi, R. S. França, J. A. Dutra, C. A. Massone, “Optical methods in length measurements and practical realization of the metre in the range of 1–1000 mm,” presented at the international seminar XVIII CBRAVIC de 21 a 24 de Julho de 1997-Petropolis, Rio de Janeiro, Brazil, Rev. Bras. Apl. Vacuo16, 38 (1997).

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited