OSA's Digital Library

Applied Optics

Applied Optics


  • Editor: Joseph N. Mait
  • Vol. 50, Iss. 8 — Mar. 10, 2011
  • pp: 1136–1157

National Ignition Facility system alignment

S. C. Burkhart, E. Bliss, P. Di Nicola, D. Kalantar, R. Lowe-Webb, T. McCarville, D. Nelson, T. Salmon, T. Schindler, J. Villanueva, and K. Wilhelmsen  »View Author Affiliations

Applied Optics, Vol. 50, Issue 8, pp. 1136-1157 (2011)

View Full Text Article

Enhanced HTML    Acrobat PDF (3230 KB)

Browse Journals / Lookup Meetings

Browse by Journal and Year


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools



The National Ignition Facility (NIF) is the world’s largest optical instrument, comprising 192 37 cm square beams, each generating up to 9.6 kJ of 351 nm laser light in a 20 ns beam precisely tailored in time and spectrum. The Facility houses a massive ( 10 m diameter) target chamber within which the beams converge onto an 1 cm size target for the purpose of creating the conditions needed for deuterium/tritium nuclear fusion in a laboratory setting. A formidable challenge was building NIF to the precise requirements for beam propagation, commissioning the beam lines, and engineering systems to reliably and safely align 192 beams within the confines of a multihour shot cycle. Designing the facility to minimize drift and vibration, placing the optical components in their design locations, commissioning beam alignment, and performing precise system alignment are the key alignment accomplishments over the decade of work described herein. The design and positioning phases placed more than 3000 large ( 2.5 m × 2 m × 1 m ) line-replaceable optics assemblies to within ± 1 mm of design requirement. The commissioning and alignment phases validated clear apertures (no clipping) for all beam lines, and demonstrated automated laser alignment within 10 min and alignment to target chamber center within 44 min . Pointing validation system shots to flat gold-plated x-ray emitting targets showed NIF met its design requirement of ± 50 μm rms beam pointing to target chamber. Finally, this paper describes the major alignment challenges faced by the NIF Project from inception to present, and how these challenges were met and solved by the NIF design and commissioning teams.

© 2011 Optical Society of America

OCIS Codes
(140.0140) Lasers and laser optics : Lasers and laser optics
(140.3530) Lasers and laser optics : Lasers, neodymium
(220.1140) Optical design and fabrication : Alignment

ToC Category:
Lasers and Laser Optics

Original Manuscript: August 30, 2010
Revised Manuscript: November 19, 2010
Manuscript Accepted: November 23, 2010
Published: March 8, 2011

S. C. Burkhart, E. Bliss, P. Di Nicola, D. Kalantar, R. Lowe-Webb, T. McCarville, D. Nelson, T. Salmon, T. Schindler, J. Villanueva, and K. Wilhelmsen, "National Ignition Facility system alignment," Appl. Opt. 50, 1136-1157 (2011)

Sort:  Author  |  Year  |  Journal  |  Reset  


  1. G. H. Miller, E. I. Moses, and C. R. Wuest, “The National Ignition Facility,” Opt. Eng. 43, 2841–2853 (2004). [CrossRef]
  2. M. L. Spaeth, K. R. Manes, C. C. Widmayer, W. H. Williams, P. K. Whitman, M. A. Henesian, I. F. Stowers, and J. Honig, “National Ignition Facility wavefront requirements and optical architecture,” Opt. Eng. 43, 2854–2865 (2004). [CrossRef]
  3. G. L. Tietbohl and S. C. Sommer, “Stability design considerations for mirror support systems in ICF lasers,” Proc. SPIE 3047, 649–660 (1997). [CrossRef]
  4. C. LeCocq, B. Fuss, and R. R. Ruland, “Status report on the alignment activities at SLAC,” in Proceedings of the 8th International Workshop on Accelerator Alignment (IWAA 2004), http://www.slac.stanford.edu/econf/C04100411/.
  5. J. D. Lindl, P. Amendt, R. L. Berger, S. G. Glendenning, S. H. Glenzer, S. W. Haan, R. L. Kaufmann, O. T. Landen, and L. J. Suter, “The physics basis for ignition using indirect-drive targets on the National Ignition Facility,” Phys. Plasmas 11, 339–491 (2004). [CrossRef]
  6. M. Bowers, S. Burkhart, S. Cohen, G. Erbert, J. Heebner, M. Hermann, and D. Jedlovec, “The injection laser system on the National Ignition Facility,” Proc. SPIE 6451, 64511M(2007). [CrossRef]
  7. R. A. Zacharias, N. R. Beer, E. S. Bliss, S. C. Burkhart, S. J. Cohen, S. B. Sutton, R. L. Van Atta, S. E. Winters, J. T. Salmon, M. R. Latta, C. J. Stolz, D. C. Pigg, and T. J. Arnold, “Alignment and wavefront control systems of the National Ignition Facility,” Opt. Eng. 43, 2873–2884(2004). [CrossRef]
  8. M. A. Rhodes, S. N. Fochs, P. J. Biltoft, T. W. Alger, B. Funkhouser, and C. D. Boley, “Plasma electrode Pockels cell for the National Ignition Facility,” Proc. SPIE 3492, 144–147(1999). [CrossRef]
  9. S. N. Dixit, M. D. Feit, M. D. Perry, and H. T. Powell, “Designing fully continuous phase screens for tailoring focal-plane irradiance profiles,” Opt. Lett. 21, 1715–1717 (1996). [CrossRef]
  10. J. M. Auerbach, P. J. Wegner, S. A. Couture, D. Eimerl, R. L. Hibbard, D. Milam, M. A. Norton, P. K. Whitman, and L. A. Hackel, “Modeling of frequency doubling and tripling with measured crystal spatial refractive-index nonuniformities,” Appl. Opt. 40, 1404–1411 (2001). [CrossRef]
  11. C. A. Haynam, P. J. Wegner, J. M. Auerbach, M. W. Bowers, S. N. Dixit, G. V. Erbert, G. M. Heestand, M. A. Henesian, M. R. Hermann, K. S. Jancaitis, K. R. Manes, C. D. Marshall, N. C. Mehta, J. Menapace, E. Moses, J. R. Murray, M. C. Nostrand, C. D. Orth, R. Patterson, R. A. Sacks, M. J. Shaw, M. Spaeth, S. B. Sutton, W. H. Williams, C. C. Widmayer, R. K. White, S. T. Yang, and B. M. Van Wonterghem, “National Ignition Facility laser performance status,” Appl. Opt. 46, 3276–303 (2007). [CrossRef]
  12. NIF Requirement 5500902-OC, “Laser system beam control & diagnostics shall point the main laser beam to center of CSF pass1 and CSF pass2 shot pinhole locations with an accuracy of better than 10% of the pinhole diameter. Laser system beam control & diagnostics shall point the main laser beam to center of CSF pass3, CSF pass4, TSF pass1 and TSF pass4 shot pinhole locations with an accuracy of better than 5% of the pinhole diameter.”
  13. NIF Requirement 5500905-0B, “For each shot, position each beam at any location within 5 cm of target chamber center such that the rms deviation of all beams from their specified positions is 50 μm or less when measured perpendicular to the beam propagation directions. No single beam shall deviate more than 200 μm. This requirement applies equally to all beams whether directed at the principal target or at equatorial backlighting targets. The accuracy of surrogate alignment shall be periodically validated by direct detection of low level pulses.”
  14. S. C. Sommer and E. S. Bliss, “Beam positioning,” Proc. SPIE 3492, 112–135 (1999). [CrossRef]
  15. C. R. Noble, M. S. Hoehler, and S. C. Sommer, “NIF ambient vibration measurements” (2002), http://www.osti.gov/servlets/purl/802614-CVIu1A/native/.
  16. P. Kemple, “Vibration measurements at NIF Site,” NIF Project Internal Report NIF-0062282 (6 February 2001).
  17. M. Tabatabale and S. Sommer, “Analysis of soil-structure interaction due to ambient vibration,” ASME Publications PVP 364 (1998), pp. 397–406.
  18. G. S. Tietbohl and S. C. Sommer, “Stability design considerations for mirror support systems in ICF lasers,” LLNL report UCRL-JC-125396 (1996), http://www.osti.gov/bridge/purl.cover.jsp?purl=/471333-QXPIoZ/webviewable/.
  19. R. E. English, C. W. Laumann, J. L. Miller, and L. G. Seppala, “Optical system design of the National Ignition Facility,” Proc. SPIE 3482, 726–736 (1998). [CrossRef]
  20. R. E. English, “Clear aperture budget for main laser system (LM1–SF4),” NIF-0000475 (19 August 1996) (internal NIF document).
  21. S. C. Burkhart, “Component placement and optical tolerancing requirements,” NIF-0053005 (16 August 2000) (internal NIF document).
  22. S. C. Burkhart, “NIF clear aperture—optical component placement tolerance revalidation,” NIF-5007159 (14 November 2000) (internal NIF document).
  23. D. W. Larson, “NIF laser line-replaceable units (LRUs),” Proc. SPIE 5341, 127–136 (2004). [CrossRef]
  24. R. E. Bonanno, “Assembling and installing line-replaceable units for the National Ignition Facility,” Opt. Eng. 432866–2872 (2004). [CrossRef]
  25. E. S. Bliss, M. Feldman, J. E. Murray, and C. S. Vann, “Laser chain alignment with low-power local light sources,” Proc. SPIE 2633, 760–767 (1995). [CrossRef]
  26. R. E. English, L. G. Seppala, C. S. Vann, and E. S. Bliss, “Use of an intermediate wavelength laser for alignment to inertial confinement fusion targets,” Proc. SPIE 2633, 603–607 (1995). Author’s note: the NIF design was modified from the 389 nm source listed in this reference to a 375 nmsource. [CrossRef]
  27. F. R. Holdener, E. Ables, E. S. Bliss, S. J. Boege, R. D. Boyd, C. J. Chocol, D. T. Davis, R. D. Demaret, R. E. English, C. W. Laumann, J. L. Miller, and S. W. Thomas, “Beam control and diagnostic functions in the NIF transport spatial filter,” Proc. SPIE 3047, 692–699 (1997). Author’s note: the “3ω sampled beam diagnostic” described in this reference was eliminated from the design for reasons of protection from 351 nm backscattered light. In addition, the TSF reticle functions were no longer required and were eliminated. [CrossRef]
  28. K. Wilhelmsen, A. Awwal, W. Ferguson, B. Horowitz, V. Miller-Kamm, and C. Reynolds, “Automatic alignment system for the National Ignition Facility,” in Proceedings of 2007 International Conference on Accelerator and Large Experimental Control Systems (ICALEPCS07) (2007), pp. 486–490, http://accelconf.web.cern.ch/accelconf/ica07/PAPERS/ROAA02.PDF.
  29. W. A. McClay III, A. A. S. Awwal, S. C. Burkhart, and J. V. Candy, “Optimization and improvement of FOA corner cube algorithm,” Proc. SPIE 5556, 227–232 (2004). [CrossRef]
  30. A. A. S. Awwal, J. V. Candy, C. A. Haynam, C. C. Widmayer, E. S. Bliss, and S. C. Burkhart, “Accurate position sensing of defocused beams using simulated beam templates,” Proc. SPIE 5556, 233–242 (2004). [CrossRef]
  31. A. A. S. Awwal, K. L. Rice, and T. M. Taha, “Fast implementation of matched-filter-based automatic alignment image processing,” Opt. Laser Technol. 41, 193–197 (2009). [CrossRef]
  32. A. A. S. Awwal, W. A. McClay, W. S. Ferguson, J. V. Candy, J. T. Salmon, and P. Wegner, “Detection and tracking of the back-reflection of KDP images in the presence or absence of a phase mask,” Appl. Opt. 45, 3038–3048 (2006). [CrossRef]
  33. A. A. S. Awwal, K. L. Rice, and T. M. Taha, “Hardware accelerated optical alignment of lasers using beam-specific matched-filters,” Appl. Opt. 48, 5190–5196 (2009). [CrossRef]
  34. J. V. Candy, W. A. McClay, A. A. S. Awwal, and S. W. Ferguson, “Optimal position estimation for the automatic alignment of a high-energy laser,” J. Opt. Soc. Am. A 22, 1348–1356 (2005). [CrossRef]
  35. J. A. Koch, S. S. Alvarez, P. M. Bell, F. D. Lee, J. D. Moody, and M. D. Landon, “Design of the National Ignition Facility static x-ray imager,” Rev. Sci. Instrum. 72, 698–700 (2001). [CrossRef]
  36. S. H. Glenzer, B. J. MacGowan, P. Michel, N. B. Meezan, L. J. Suter, S. N. Dixit, J. L. Kline, G. A. Kyrala, D. K. Bradley, D. A. Callahan, E. L. Dewald, L. Divol, E. Dzenitis, M. J. Edwards, A. V. Hamza, C. A. Haynam, D. E. Hinkel, D. H. Kalantar, J. D. Kilkenny, O. L. Landen, J. D. Lindl, S. LePape, J. D. Moody, A. Nikroo, T. Parham, M. B. Schneider, R. P. J. Town, P. Wegner, K. Widmann, P. Whitman, B. K. F. Young, B. Van Wonterghem, L. J. Atherton, and E. I. Moses, “Symmetric inertial confinement fusion implosions at ultra-high laser energies,” Science 327, 1228–1231(2010). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited