OSA's Digital Library

Optics Express

Optics Express

  • Editor: Michael Duncan
  • Vol. 11, Iss. 21 — Oct. 20, 2003
  • pp: 2730–2735
« Show journal navigation

Passive Q-switching by Tm3+co-doping of a Yb3+-fiber laser

P. Adel, M. Auerbach, C. Fallnich, S. Unger, H.-R. Müller, and J. Kirchhof  »View Author Affiliations


Optics Express, Vol. 11, Issue 21, pp. 2730-2735 (2003)
http://dx.doi.org/10.1364/OE.11.002730


View Full Text Article

Acrobat PDF (368 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

Q-switching of a wavelength tunable Yb3+-doped double-clad fiber laser by a Tm3+-codoping in the gain fiber is demonstrated. This system showed up to 2.4 W output power, up to 140 kHz repetition rate, a maximum pulse energy of 21.8 µJ and a minimum pulse duration of 1.1 µs. Using a grating pair in Littrow-Littman configuration the emission wavelength was tunable between 1055 nm and 1090 nm. The output radiation showed a maximum spectral linewidth of 4 GHz.

© 2003 Optical Society of America

Introduction

Pulsed lasers are extremely useful for applications like frequency conversion, or marking of plastics because of the higher peak power compared to cw-lasers [1

1. A. Hideur, T. Chartier, M. Brunel, M. Salhi, C. Ozkul, and F. Sanchez “Mode-lock, Q-switch and CW operation of an Yb-doped double-clad fiber ring laser,” Opt. Commun. 198, 141–146 (2002) [CrossRef]

]. Additionally for these applications a good beam quality is important that can be accomplished by light propagation in single-mode fibers. Therefore, it is very promising to combine the Q-switching technique with the advantages of fiber lasers.

2. Experimental set-up

Figure 1 shows the detailed laser set-up, which consists of the following main components: a Yb3+-doped double-clad fiber with Tm3+-codoping that provides the gain and the saturable absorption, quarter- (QWP) and half-wave-plates (HWP), a Faraday rotator (FR) for unidirectional laser operation and a grating pair (1200 lines/mm, gold coated) in Littrow-Littman configuration for tunable narrow-linewidth operation. The polarization beam splitter (PBS2) at the input of the FR acted as a variable output coupler in combination with HWP2. In addition, a polarization beam splitter (PBS1) was placed in front of this HWP2 to fix the polarization state and therefore the outcoupling factor at the PBS1. Otherwise the cavity loss could be reduced by nonlinear polarization effects at high outcoupling factors which would favor polarization rotation mode-locking. The gain fiber with a dopant concentration of 1500 ppm Yb203 and about 5 ppm Tm2O3 had a pump and laser core diameter of 250 µm and 7 µm, respectively. For this fiber with a cut-off wavelength below 1,0 µm a D-shaped pump core was chosen for improved pump light absorption.

Fig. 1. Set-up of the tunable Q-switched fiber laser system.

The light from the fiber was steered by mirrors M1 and M2 through a polarization beam splitter and to the variable output coupler consisting of HWP2 and the PBS2 in front of the FR. Behind the FR, the signal propagated towards the grating pair. The wavelength of the back reflected signal was determined by adjustment of the incident angle on the Littrow tuning grating. For the back-reflected signal the FR in combination with the PBS2 acted as an optical circulator and the beam was then coupled into the Yb3+-fiber via mirror M3. The polarization at the fiber input was determined by the settings of the zeroth-order (1064 nm) wave-plates (HWP1 + QWP).

3. Results and discussion

Using a set-up with a 20 m long gain fiber and an output coupling factor adjusted to 65% stable pulsed operation started at 5.6 W launched pump power for appropriate waveplate settings. At this threshold the laser showed a repetition rate of 20.1 kHz and an output power of 33 mW while the wavelength was kept fixed to 1065 nm. At maximum pump power of 21.9 W an output power of 1.44 W at a repetition rate of 98.1 kHz was achieved. The output power and the repetition rate versus pump power are plotted in Fig. 2(a). The output power did not increase linearly with pump power but showed a S-shaped curve. This was due to a thermally induced increase of the pump diode wavelength with pump power. While the laser diode case was mounted on a heat sink with constant temperature the laser emitter temperature, and therefore the emission wavelength, increased with pump power, because of the increased heat generation. In combination with the relatively narrow absorption peak of Yb3+ at 975 nm, the pump wavelength moves closer to the absorption peak with increasing pump power resulting in an improved pump light absorption. This was confirmed by measurements of the transmitted pump power which showed that the pump light absorption increased with pump power especially at medium power levels.

Figure 2(b) shows the pulse energy as a function of the pump power. The pulse energy was calculated from the measured output power and repetition rate. The pulse energy increased nearly linear from 1.6 µJ at 5.6 W pump power to a maximum of 15.1 µJ at 19.7 W pump power. For even higher pump powers the pulse energy decreased slightly with pump power.

Furthermore, the pulse width (FWHM) as a function of the pump power, measured with a 2 GHz photodiode and a 500 MHz oscilloscope, is shown in Fig. 2(b). The pulse width decreased asymptotically from 6.5 µs to 1.1 µs with increasing pump power. Typically the Q-switched pulses showed a substructure above the µs pulse pedestal with a periodicity equal to the cavity round trip time (left diagram in figure 3). The width of this substructure pulses in the oscilloscope trace was roughly equal to the resolution limit of the oscilloscope of about 2 ns. The pulse width of the µs pulse pedestal was determined by reducing the detection bandwidth electronically to about 20 MHz and therefore smoothing the signal. It can be seen from Fig. 3 (red curve) that the 20 MHz trace nearly coincides with the 500 MHz resolution curve, except for the ns peaks. This trace show, that the contribution of the ns peaks to the total energy of the µs pulses is quite small (<5%). It should be noted, that the amplitude of the substructure depended on waveplate settings and the coiling (twist) of the fiber and that also Q-switched operation without such a substructure was observed. A typical photodiode trace of the output signal on a larger time scale is shown in the right diagram of Fig. 3. The variations of the pulse amplitude in this diagram are attributable to the discrete sampling of the digital oscilloscope in combination with the pulse substructure. No variations of the peak amplitude were observed on an analog oscilloscope with 20 MHz bandwidth.

Fig. 2. Output power, repetition rate, pulse width and pulse energy as a function of the pump power.
Fig 3. Left diagram: 500 MHz Oscilloscope trace (black) of a Q-switched pulse which shows the nssubstructure above the µs pulse pedestal. The red curve shows the averaged time signal (averaging time 5 ns). Right diagram: Typical “long-time” photodiode trace of the Q-switched fiber laser output signal.

Variations of the output coupling (OC) from 0 to 90% resulted in up to 20% increase of the pulse width relative to the pulse width minimum which was observed for OC’s between 50% and 65%. Furthermore, the output power increased roughly linearly with the OC factor, while its influence on the repetition rate was below 5%. Only unstable Q-switching was achieved for extremely high output coupling factors (i.e., >90% at 15 W pump power).

Using a Yb3+-doped fiber without an additional Tm3+-doping in the set-up, we could achieve only a cw output or random fluctuations but no stable pulsed operation. This indicated, that the pulsed operation is due to a saturable absorption effect of the codoped Tm3+-ions. In addition, during infrared laser operation, the codoped gain fiber shows a blue fluorescence. The brightness of this spontaneous emission at about 480 nm increased with signal intensity and was much stronger than for conventional Yb3+-doped fibers.

Table 1. Laser data for set-ups with a 20 m and a 32 m long gain fiber

table-icon
View This Table

The effect of the Tm3+-ions on laser operation of the Yb3+-fiber is similar to the saturable absorption effect of Er3+-clusters in heavily doped Er3+-fibers which also favors self-pulsing operation [8

8. S. Colin, E. Contesse, P. Le Boudec, G. Stephan, and F. Sanchez, “Evidence of a saturable-absorption effect in heavily erbium-doped fibers,” Opt. Lett. 21, 1987 – 1989 (1996) [CrossRef] [PubMed]

]. For these systems the loss modulation of the Tm3+-ions or Er3+-ion clusters, respectively, is weak relative to fiber gain. Hence the passive modulation amplitude is relative small relative to the fiber gain which is also indicated by the above mentioned simulations (~3% modulation in Fig. 4(b). However, the pulse duration in the µs range and the observed high duty cycle were an indication that laser operation was also influenced by relaxation oscillations. Calculation of the relaxation oscillation frequency based on standard relaxation theory showed a good agreement between the calculated and the observed repetition rate as a function of the pump power for both set-ups [11

11. Siegman, “Lasers,” University Science Books, Sausalito (1986)

]. For these calculations a cavity round trip loss of 90% was assumed and the lifetime of the upper Yb3+-level was calculated by taking into account the emitted signal power, the pump and signal intensities and the absorption and emission cross sections. The deviations between calculated and measured repetition rates were below 10%. Such a relation was also previously reported for heavily doped Er3+-fibers [12

12. R. Rangel-Rojo and M. Mohebi, “Study of the onset of self-pulsing behaviour in an Er-doped fibre laser,” Opt. Commun. 137, 98 – 102 (1997) [CrossRef]

]. This correspondence and the above mentioned properties of the Tm3+-codoping leads to the conclusion that the saturable absorption of the Tm3+-ions initiates and sustains relaxation oscillations in the Yb3+-fiber. Consequently repetition rate and pulse build up can be calculated by standard relaxation theory for different doping concentrations and fiber lengths.

Fig. 4. Energy level diagram for Tm3+-ions (left). Pump transitions and fluorescence are indicated by vertical dashed arrows. Nonradiative decays which are relevant for the upconversion process (solid) or which are taken into account for the calculations (dashed) are indicated by diagonal arrows. For the pump transitions the wavelength of the absorption peaks are shown. Lifetimes which were determined by calculation of the nonradiative decay rates are in brackets (same relation between energy gap and nonradiative decay rate as in Er3+-silica fibers assumed [10]). Lifetime of the 1G4 level was determined from the exponential decay of the blue fluorescence. Right diagram shows the calculated Tm3+-absorption (upper curve) of the 32 m fiber. The lower curve shows the corresponding intra-cavity signal (20 µJ, 1.5 µs, 65 kHz).

For both set-ups the Q-switched operation was influenced by the waveplate settings which is due to the following effects. On the one hand the resonator loss depends on the birefringence of the fiber and the waveplates. On the other hand, the polarization evolution in the fiber depends on the signal intensity for an elliptically polarized signal due to the Kerr-effect, which can be used for mode locking [13

13. P. Adel, M. Auerbach, C. Fallnich, S. Unger, and H.-R. Müller, “Super-stretched mode-locked Yb3+-fiber ring laser with 40 nm bandwidth, 9.5 nJ pulse energy and 630 mW output power,” Opt. Commun. 211, 283 – 287 (2002) [CrossRef]

]. In standard gain fibers the birefringence shows random fluctuations which results in an elliptical polarization state somewhere in the fiber. Hence the typically observed ns substructure of the µs pulse is likely due to nonlinear polarization effects in the fiber. Both effects could be avoided by a polarization maintaining (PM) gain fiber. For such a fiber no birefringence compensation by waveplates is required and the linear polarization along the fiber avoids nonlinear polarization rotation effects.

By rotating the tuning grating the signal wavelength was tunable between 1055 and 1085 nm (1059 and 1090 nm) for the 20 m (32 m) set-up. This was measured at a pump power of 16.8 W (13.7 W). The spectra, measured with a resolution of 0.5 nm, showed also that the spectral intensity of the amplified spontaneous emission was at least 37 dB lower than the main laser radiation. If the tuning grating position was adjusted for a emission wavelength outside the above mentioned tuning limits only unstable Q-switching was observed. In the wings of the tuning range the repetition rate and the pulse width increased typically up to a factor of two. The maximum output power was measured at about 1065 nm and decreased only slightly (< 15%) if the wavelength was detuned. However at the long wavelength limit for the 32 m fiber a power drop of up to 35% was observed.

In order to determine the linewidth of the laser, a confocal scanning Fabry-Perot interferometer with 10 GHz free spectral range and a finesse of 150 was used. The measured linewidth increased for the pump power ranges mentioned in table 1 from 0.17 GHz to 2.3 GHz (from 0.35 GHz to 4 GHz) with pump power for the 20 m (32 m) set-up. This increase was nearly linear at low pump powers and showed an asymptotic behaviour at higher pump power levels. Regarding the linewidth it should be noted that for cw-operation of a similar set-up with a conventional 20 m long Yb3+-fiber nearly the same linewidth (<2.5 GHz) was observed [14

14. M. Auerbach, P. Adel, D. Wandt, C. Fallnich, S. Unger, S. Jetschke, and H. R. Mueller “10 W widely tunable narrow linewidth double-clad fiber ring laser,” Opt. Express 10, 139–144 (2002), http://www.opticsexpress.org/abstract.cfm?URI=OPEX-10-2-1391 [CrossRef] [PubMed]

].

4. Conclusion

To our knowledge we realized the first tunable Yb3+-fiber laser passively Q-switched by a Tm3+-codoping of the gain fiber. Q-switched operation (up to 21.8 µJ, 140 kHz, 1.1 µs), in combination with narrow linewidth operation (<4 GHz) and wavelength tunability between 1055 and 1090 nm was demonstrated. It was shown, that the pulsed output of this system is due to relaxation oscillations which were sustained by saturable absorption of the Tm3+-ions. Detailed simulations of the Tm3+-absorption dynamics and variation of the concentration and the axial distribution of the Yb3+- and the Tm3+-doping for further optimization of the laser’s Q-switching performance are in progress.

Acknowledgments

This research is supported by the German Ministry of Science, Education, Research and Technology under contract 13N7799. We like to thank one reviewer for taking our attention to Ref. [4

4. L. Tordella, H. Dejellout, B. Dussardier, A. Saissy, and G. Monnom, “High repetition rate passively Q-switched Nd3+:Cr4+ all fibre laser,” Electron. Lett. 39, 1307 – 1308 (2003) [CrossRef]

].

References and links

1.

A. Hideur, T. Chartier, M. Brunel, M. Salhi, C. Ozkul, and F. Sanchez “Mode-lock, Q-switch and CW operation of an Yb-doped double-clad fiber ring laser,” Opt. Commun. 198, 141–146 (2002) [CrossRef]

2.

Z. Y. Chen, A. B. Grudinin, J. Porta, and J. D. Minelly, “Enhanced Q switching in double-clad fiber lasers,” Opt. Lett. 23, 454–456 (1998) [CrossRef]

3.

K. Takaichi, J. Lu, T. Murai, T. Uematsu, A. Shirakawa, K. Ueda, H. Yagi, T. Yanagitani, and A. Kaminskii, “Chromium Doped Y3Al5O12 Ceramics - a Novel Saturable Absorber for Passively Self-Q-switched One-Micron Solid State Lasers,” Jpn. J. Appl. Phys. 41, L96–L98 (2002) [CrossRef]

4.

L. Tordella, H. Dejellout, B. Dussardier, A. Saissy, and G. Monnom, “High repetition rate passively Q-switched Nd3+:Cr4+ all fibre laser,” Electron. Lett. 39, 1307 – 1308 (2003) [CrossRef]

5.

P. Gross, M. E. Klein, T. Walde, K.-J. Boller, M. Auerbach, P. Wessels, and C. Fallnich, “Fiber-laser-pumped continuous-wave singly resonant optical parametric oscillator,” Opt. Lett. 27, 418 – 420 (2002) [CrossRef]

6.

E. B. Mejia, A. N. Starodumov, and Y. O. Barmenkov, “Blue and infrared up-conversion in Tm3+-doped fluorozirconate fiber pumped at 1.06, 1.117 and 1.18 µm,” Appl. Phys. Lett. 74, 1540 – 1554 (1999) [CrossRef]

7.

R. Caspary “Applied Rare-Earth Spectroscopy for Fiber Laser Optimization,” Shaker, Aachen (2002)

8.

S. Colin, E. Contesse, P. Le Boudec, G. Stephan, and F. Sanchez, “Evidence of a saturable-absorption effect in heavily erbium-doped fibers,” Opt. Lett. 21, 1987 – 1989 (1996) [CrossRef] [PubMed]

9.

S. D. Jackson and T. A. King, “Dynamics of the output of heavily Tm-doped double clad silica fiber lasers,” J. Opt. Soc. Am. B 16, 2178 – 2188 (1999) [CrossRef]

10.

M. V. D. Vermelho, U. Peschel, and J. S. Aitchison, “Simple and Accurate Procedure for Modeling Erbiumdoped Waveguide Amplifiers with High Concentrations,” J. Lightwave Technol. 18, 401 – 408 (2000) [CrossRef]

11.

Siegman, “Lasers,” University Science Books, Sausalito (1986)

12.

R. Rangel-Rojo and M. Mohebi, “Study of the onset of self-pulsing behaviour in an Er-doped fibre laser,” Opt. Commun. 137, 98 – 102 (1997) [CrossRef]

13.

P. Adel, M. Auerbach, C. Fallnich, S. Unger, and H.-R. Müller, “Super-stretched mode-locked Yb3+-fiber ring laser with 40 nm bandwidth, 9.5 nJ pulse energy and 630 mW output power,” Opt. Commun. 211, 283 – 287 (2002) [CrossRef]

14.

M. Auerbach, P. Adel, D. Wandt, C. Fallnich, S. Unger, S. Jetschke, and H. R. Mueller “10 W widely tunable narrow linewidth double-clad fiber ring laser,” Opt. Express 10, 139–144 (2002), http://www.opticsexpress.org/abstract.cfm?URI=OPEX-10-2-1391 [CrossRef] [PubMed]

OCIS Codes
(140.3480) Lasers and laser optics : Lasers, diode-pumped
(140.3510) Lasers and laser optics : Lasers, fiber
(140.3540) Lasers and laser optics : Lasers, Q-switched
(140.3560) Lasers and laser optics : Lasers, ring
(140.3600) Lasers and laser optics : Lasers, tunable

ToC Category:
Research Papers

History
Original Manuscript: July 9, 2003
Revised Manuscript: October 13, 2003
Published: October 20, 2003

Citation
P. Adel, M. Auerbach, Carsten Fallnich, S. Unger, H. Müller, and J. Kirchhof, "Passive Q-switching by Tm3+co-doping of a Yb3+-fiber laser," Opt. Express 11, 2730-2735 (2003)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-11-21-2730


Sort:  Journal  |  Reset  

References

  1. A. Hideur, T. Chartier, M. Brunel, M. Salhi, C. Ozkul, F. Sanchez �?? Mode-lock, Q-switch and CW operation of an Yb-doped double-clad fiber ring laser,�?? Opt. Commun. 198, 141-146 (2002) [CrossRef]
  2. Z. Y. Chen, A. B. Grudinin, J. Porta, J. D. Minelly, �??Enhanced Q switching in double-clad fiber lasers,�?? Opt. Lett. 23, 454-456 (1998) [CrossRef]
  3. K. Takaichi, J. Lu, T. Murai, T. Uematsu, A. Shirakawa, K. Ueda, H. Yagi, T. Yanagitani, A. Kaminskii, �??Chromium Doped Y3Al5O12 Ceramics �?? a Novel Saturable Absorber for Passively Self-Q-switched One- Micron Solid State Lasers,�?? Jpn. J. Appl. Phys. 41, L96-L98 (2002) [CrossRef]
  4. L. Tordella, H. Dejellout, B. Dussardier, A. Saissy, G. Monnom, �??High repetition rate passively Q-switched Nd3+:Cr4+ all fibre laser,�?? Electron. Lett. 39, 1307 - 1308 (2003) [CrossRef]
  5. P. Gross, M. E. Klein, T. Walde, K.-J. Boller, M. Auerbach, P. Wessels, C. Fallnich, �??Fiber-laser-pumped continuous-wave singly resonant optical parametric oscillator,�?? Opt. Lett. 27, 418 �?? 420 (2002) [CrossRef]
  6. E. B. Mejia, A. N. Starodumov, Y. O. Barmenkov, �??Blue and infrared up- onversion in Tm3+-doped fluorozirconate fiber pumped at 1.06, 1.117 and 1.18 µm,�?? Appl. Phys. Lett. 74, 1540 �?? 1554 (1999) [CrossRef]
  7. R. Caspary �??Applied Rare-Earth Spectroscopy for Fiber Laser Optimization,�?? Shaker, Aachen (2002)
  8. S. Colin, E. Contesse, P. Le Boudec, G. Stephan, F. Sanchez, �??Evidence of a saturable-absorption effect in heavily erbium-doped fibers,�?? Opt. Lett. 21, 1987 - 1989 (1996) [CrossRef] [PubMed]
  9. S. D. Jackson, T. A. King, �??Dynamics of the output of heavily Tm-doped double clad silica fiber lasers,�?? .J Opt. Soc. Am. B 16, 2178 �?? 2188 (1999) [CrossRef]
  10. M. V. D. Vermelho, U. Peschel, J. S. Aitchison, �??Simple and Accurate procedure for Modeling Erbium-doped Waveguide Amplifiers with High Concentrations,�?? J. Lightwave Technol. 18, 401 - 408 (2000) [CrossRef]
  11. Siegman, �??Lasers,�?? University Science Books, Sausalito (1986)
  12. R. Rangel-Rojo, M. Mohebi, �??Study of the onset of self-pulsing behaviour in an Er-doped fibre laser,�?? Opt. Commun. 137, 98 �?? 102 (1997) [CrossRef]
  13. P. Adel, M. Auerbach, C. Fallnich, S. Unger, H.-R. Müller, �??Super- tretched mode-locked Yb3+-fiber ring laser with 40 nm bandwidth, 9.5 nJ pulse energy and 630 mW output power,�?? Opt. Commun. 211, 283 - 287 (2002) [CrossRef]
  14. M. Auerbach, P. Adel, D. Wandt, C. Fallnich, S. Unger, S. Jetschke, H. R. Mueller �?? 10 W widely tunable narrow linewidth double-clad fiber ring laser,�?? Opt. Express 10, 139-144 (2002), <a href="http://www.opticsexpress.org/abstract.cfm?URI=OPEX-10-2-139">http://www.opticsexpress.org/abstract.cfm?URI=OPEX-10-2-139</a> [CrossRef] [PubMed]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1. Fig. 2. Fig 3.
 
Fig. 4.
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited