OSA's Digital Library

Optics Express

Optics Express

  • Editor: Michael Duncan
  • Vol. 12, Iss. 5 — Mar. 8, 2004
  • pp: 907–915
« Show journal navigation

Pulse-amplitude equalization in a rational harmonic mode-locked semiconductor fiber ring laser using a dual-drive Mach-Zehnder modulator

Yun Jong Kim, Chung Ghiu Lee, Young Yun Chun, and Chang-Soo Park  »View Author Affiliations


Optics Express, Vol. 12, Issue 5, pp. 907-915 (2004)
http://dx.doi.org/10.1364/OPEX.12.000907


View Full Text Article

Acrobat PDF (516 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We present and demonstrate a simple method of pulse-amplitude equalization in a rational harmonic mode-locked semiconductor ring laser, using a dual-drive Mach-Zehnder (MZ) modulator. Pulse-amplitude equalization was achieved by adjusting the voltages applied to both arms of the modulator, such that each mode-locked pulse experiences the same transmission coefficient in the transmission curve of the modulator. With this method, amplitude-equalized pulse trains with repetition rates of ~7.42GHz (third rational harmonic) and ~12.34GHz (fifth rational harmonic) were successfully obtained without any additional function to the ring laser itself.

© 2004 Optical Society of America

1. Introduction

A stable pulse train with high repetition rate is very essential for a high-speed OTDM system. An actively mode-locked fiber laser is ideal for generating a short pulse train with various bit rates. Recently, rational harmonic mode-locking techniques that generate pulse trains with high repetition rates have been reported [1

1. C. Wu and N. K. Dutta, “High-repetition-rate optical pulse generation using a rational harmonic mode-locking fiber laser,” IEEE J. Quantum Electron. 36, 145–150 (2000). [CrossRef]

, 2

2. N. Onodera, A. J. Lowery, L. Zhai, Z. Ahmed, and R. S. Tucker, “Frequency multiplication in actively mode-locked semiconductor lasers,” Appl. Phys. Lett. 62, 1329–1331 (1993). [CrossRef]

, 3

3. Z. Ahmed and N. Onodera, “High repetition rate optical pulse generation by frequency mudltiplication in actively modelocked fibre ring lasers,” Electron. Lett. 32, 455–457 (1996). [CrossRef]

]. When the repetition rate of the generated optical pulse train becomes an integer multiple of the RF drive frequency, the amplitudes among the pulses become varied and characterized by large fluctuations. To overcome this unevenness, several methods have been reported, including the use of another fiber laser with a nonlinear optical loop mirror (NOLM) [4

4. M. -Y. Jeon, H. K. Lee, J. T. Ahn, K. H. Kim, D. S. Lim, and E. -H. Lee, “Pulse-amplitude-equalized output from a rational harmonic mode-locked fiber laser,” Opt. Lett. 23, 855–857 (1998). [CrossRef]

] and an SOA loop mirror [5

5. H. J. Lee, K. Kim, and H. G.. Kim, “Pulse-amplitude equalization of rational harmonic mode-locked fiber laser using a semiconductor optical amplifier loop mirror,” Opt. Commun. 160, 51–56 (1999). [CrossRef]

], nonlinear polarization rotation (NPR) [6

6. Z. Li, C. Lou, K. T. Chan, Y. Li, and Y. Gao, “Theoretical and Experimental Study of Pulse-Amplitude-Equalization in a Rational Harmonic Mode-Locked Fiber Ring Laser,” IEEE J. Quantum Electron. 37, 33–37 (2001). [CrossRef]

], and optical feedback [7

7. C. G. Lee, Y. J. Kim, H. K. Choi, and C. -S. Park, “Pulse-amplitude equalization in a rational harmonic mode-locked semiconductor ring laser using optical feedback,” Opt. Commun. 209, 417–425 (2002). [CrossRef]

]. G. Zhu, et al. were able to show theoretically an equalized amplitude pulse train up to the fourth order rational harmonic mode-locking [8

8. G. Zhu, H. Chen, and N. Dutta, “Time domain analysis of a rational harmonic mode locked ring fiber laser,” J. Appl. Phys. 90, 2143–2147 (1990). [CrossRef]

]. In a semiconductor-based ring laser, however, DC biasing the single electrode intensity modulator of an actively mode-locked fiber ring laser is commonly known to generate optical pulses at repetition rates that are twice as much as those of the RF drive frequency [9

9. A. Takada and H. Miyazawa, “30GHz picosecond pulse generation from actively mode-locked erbium-doped fibre laser,” Electron. Lett. 26, 216–217 (1990). [CrossRef]

].

In this letter, We propose a simple method of equalizing pulse-amplitudes of rational harmonic mode-locked pulses in a semiconductor-based ring laser. Equalization can be easily achieved by using a dual-drive LiNbO3 Mach-Zehnder (MZ) modulator placed inside the ring laser itself and individually adjusting two voltages to the modulator. With this simple structure, amplitude-equalized pulse trains with more than two times the RF modulation frequency can be realized and will be demonstrated experimentally without introducing additional components or changes in structure.

2. Principle of pulse-amplitude equalization

The multiplication of repetition rate by rational harmonic mode-locking has been described in the literatures [1

1. C. Wu and N. K. Dutta, “High-repetition-rate optical pulse generation using a rational harmonic mode-locking fiber laser,” IEEE J. Quantum Electron. 36, 145–150 (2000). [CrossRef]

, 2

2. N. Onodera, A. J. Lowery, L. Zhai, Z. Ahmed, and R. S. Tucker, “Frequency multiplication in actively mode-locked semiconductor lasers,” Appl. Phys. Lett. 62, 1329–1331 (1993). [CrossRef]

, 3

3. Z. Ahmed and N. Onodera, “High repetition rate optical pulse generation by frequency mudltiplication in actively modelocked fibre ring lasers,” Electron. Lett. 32, 455–457 (1996). [CrossRef]

]. If the RF drive frequency (fmod) is equal to a harmonic of the fundamental cavity frequency (fcav), that is, fmod=nfcav (n is a positive integer), the nth-order harmonic mode-locking occurs, and the pulse repetition rate (frep) is the same as the RF drive frequency. That is frep=fmod=nfcav. To achieve rational harmonic mode-locking, the modulation frequency is slightly detuned from the harmonic mode-locking condition by fcav/p. Thus fmod=nfcav ± fcav/p, where p is a positive integer. The pulse train of the repetition rate at p times the RF drive frequency can then be obtained (frep=pfmod). Figures 1(a) and 1(d) show the third (p=3) rational harmonic mode-locked pulse train as an example. The pulse repetition rate becomes three times the RF drive frequency (frep=3 fmod, i.e., Trep=Tmod/3) [7

7. C. G. Lee, Y. J. Kim, H. K. Choi, and C. -S. Park, “Pulse-amplitude equalization in a rational harmonic mode-locked semiconductor ring laser using optical feedback,” Opt. Commun. 209, 417–425 (2002). [CrossRef]

]. Tmod is the time interval of the modulation frequency for harmonic mode-locking. The pulses in solid line in Fig. 1(a) indicate the harmonic mode-locked pulses.

The amplitudes of the generated harmonic mode-locked pulses are determined by the transmission coefficients through the MZ modulator. Generally, the transmission curve of the modulator from input port to output port is defined as TMZM(t)=Iout (t)/Iin(t), where Iin=|Ein(t)|2, Iout=|Eout (t)|2, and Iin(t) denotes the shape of the input optical pulse train at time t to the modulator. Ein and Eout are the input and output optical fields, respectively. The output field of the dual drive MZ modulator is given by

Eout(t)=Ein(t)2[exp(jπv1(t)Vπ)+γexp(jπv2(t)Vπ)],
(1)

v1(t)=Vbias1+Vacsin(2πfmodt+ϕ1)
v2(t)=Vbias2+Vacsin(2πfmodt+ϕ2),
(2)

where Vac is a modulation amplitude, V bias1 and V bias2 the bias voltages applied to arm1 and arm2, ϕ 1 and ϕ 2 the phase of applied voltage to arm1 and arm2, respectively. Figure 2 shows the calculated values of the modulation amplitude, Vac, in order to achieve the pulse-amplitude equalization for the third (p=3) and the fifth (p=5) rational harmonic mode-locking. When the phase difference between the applied voltages is π, |ϕ 1-ϕ 2|=π, small amount of modulation amplitude is sufficient to acquire pulse-amplitude equalization for the third (p=3) and the fifth (p=5) rational harmonic mode-locking cases. Pulse-amplitude equalization can be easily achieved in that condition.

Fig. 1. Timing diagrams for pulse-amplitude equalization. (a), (d) The input pulse train of the MZ modulator, (b), (e) transmission curve of the MZ modulator, and (c), (f) the output pulse train of the MZ modulator. [(a), (b), and (c)] are due to the small signal modulation (Vac <Vπ) and [(d), (e), and (f)] large signal modulation (Vac >Vπ).

Therefore, we choose the phase difference of π for pulse-amplitude equalization with small modulation amplitude. In our case, ϕ 1=0 and ϕ 2=π. Then, the voltages are described as

v1(t)=Vbias1+Vacsin(2πfmodt)=Vbias1+vac(t)
v2(t)=Vbias2+Vacsin(2πfmodt+π)=Vbias2+vac¯(t),
(3)

where vac(t)=|Vac|sin(2πf mod t), vac¯(t)=Vacsin(2πfmodt+π). The output optical pulse train derived from Eq. (1) is expressed as

Iout(t)=Ein(t)24[1+γ2+2γcos(πv1(t)Vππv2(t)Vπ)].
(4)

Therefore, TMZM(t) is given as

TMZM(t)=14[1+γ2+2γcos(πv1(t)Vππv2(t)Vπ)].
5)

Figures 1(b) and 1(e) represent the transmission curves of the MZ modulator given by Eq. (5). As shown in Fig. 1(b), the third rational harmonic mode-locking pulses experience different transmission coefficients in the MZ modulator. This causes the pulse-amplitude variation. This pulse-amplitude fluctuation has been known to result from the interaction between circulating pulses and cavity loss modulation [3

3. Z. Ahmed and N. Onodera, “High repetition rate optical pulse generation by frequency mudltiplication in actively modelocked fibre ring lasers,” Electron. Lett. 32, 455–457 (1996). [CrossRef]

]. Equalization of pulse-amplitudes occurs only when the pulse gets the same transmission coefficient in the modulator [8

8. G. Zhu, H. Chen, and N. Dutta, “Time domain analysis of a rational harmonic mode locked ring fiber laser,” J. Appl. Phys. 90, 2143–2147 (1990). [CrossRef]

]. The transmission curve of the modulator depends on the voltages applied to each arm of the MZ modulator. By adjusting the voltages applied to the modulator, i.e., bias voltages,V bias1,V bias2 and the modulation amplitude, Vac, the shape of transmission curve can be changed from Fig. 1(b) to Fig. 1(e). Conventional rational harmonic mode-locked pulse is usually obtained by operating the modulator with the peak-to-peak amplitude of the applied voltage (Vac) smaller than that of the switching voltage, Vπ as shown in Fig. 1(c). On the contrary, by providing voltages larger than the switching voltage of the modulator, more minimum and maximum values of transmission curve can be generated in such a way that the rational harmonic mode-locked pulses experience almost the same transmission coefficient. This is to the case of similar in the single-drive modulator [8

8. G. Zhu, H. Chen, and N. Dutta, “Time domain analysis of a rational harmonic mode locked ring fiber laser,” J. Appl. Phys. 90, 2143–2147 (1990). [CrossRef]

], but the freedom of adjusting is largely limited because only one voltage can be used to obtain the phase variation. Figure 1(e) is the result of large modulation (Vac >Vπ) with a dual control. In this case, transmission coefficients are almost equal to the mode-locked pulses arriving to the modulator and, as a result, pulse-amplitude equalization of the third (p=3) rational harmonic mode-locked pulse train is obtained (see Fig. 1(f)). The dash-and-dotted horizontal line is drawn for showing the same transmission coefficient met by the input optical pulses.

Fig. 2. Minimum modulation amplitude as a function of phase difference between the two applied signals for a pulse-amplitude equalization with mode-locking cases of p=3 and p=5.
Fig. 3. Simulated pulse trains (solid line) and transmission curves (dotted line) for the third (p=3) rational harmonic mode-locking (a) without pulse-amplitude equalization (V bias1=1.51Vπ, V bias2=1.51Vπ and Vac=0.86Vπ) and (b) with pulse-amplitude equalization (V bias1=1.30Vπ, V bias2=1.40Vπ and Vac=1.01Vπ).
Fig. 4. Simulated pulse trains (solid line) and transmission curves (dotted line) for the fifth (p=5) rational harmonic mode-locking (a) without pulse-amplitude equalization (V bias1=1.50Vπ, V bias2=1.50Vπ and Vac=0.83Vπ) and (b) with pulse-amplitude equalization (V bias1=1.30Vπ, V bias2=1.72Vπ and Vac=1.12Vπ).

Fig. 5. Experimental setup. PC: polarization controller; PPG: pulse pattern generator; SOA: semiconductor optical amplifier; OTDL: optical tunable delay line; ATT: RF attenuator.

3. Experiments and results

3.1. Experimental setup

To demonstrate pulse-amplitude equalization in a rational harmonic mode-locked semiconductor fiber ring laser, the experimental setup depicted in Fig. 5 was built. The rational harmonic mode-locked semiconductor fiber ring laser was composed of a semiconductor optical amplifier (SOA), an optical tunable delay line (OTDL), a polarization controller (PC), an isolator, and a dual-electrode LiNbO3 MZ type modulator. The modulator, which has 10Gb/s bandwidth, switching voltage of ~5V, and insertion loss of 6dB, is connected to a high-speed differential driver. An RF clock from the pulse pattern generator (PPG) was applied to the differential driver (Anritsu A3HD2106), which gives the differential outputs with π phase difference to each other but the same amplitude. Then, V bias1 and V bias2 are controlled individually. The SOA (Alcatel 1901) is a polarization-insensitive type (0.6dB typically) with low tensile bulk separate confinement heterostructure, and its gain and cavity length are 25dB and 1000µm, respectively. It has a carrier lifetime of ~320ps. It was driven at the operating bias current of 95.7mA. The cavity length was estimated to be 22.31m, corresponding to a fundamental frequency of ~8.96MHz. The output pulse train from the rational harmonic mode-locked fiber laser was measured using a 3dB coupler. It was electrically converted by a high-speed photodiode with a 26GHz bandwidth and a 12ps full-width half maximum (FWHM) impulse response. The converted electrical signal was measured directly using an RF spectrum analyzer without a low-noise RF preamplifier.

3.2. Third rational harmonic mode-locking (p=3)

Conventional active mode-locking was obtained at 1560nm at a modulation frequency of 2.48832GHz (~277th harmonics), driven by the pulse pattern generator. By slightly detuning the RF drive frequency from the mode-locking frequency by fcav/p with an integer p, the pth rational harmonic mode-locked optical pulse train was obtained from the rational harmonic mode-locked semiconductor fiber laser [7

7. C. G. Lee, Y. J. Kim, H. K. Choi, and C. -S. Park, “Pulse-amplitude equalization in a rational harmonic mode-locked semiconductor ring laser using optical feedback,” Opt. Commun. 209, 417–425 (2002). [CrossRef]

]. Based on this relationship, the third rational harmonic mode-locking (p=3) was observed at the modulation frequency of 2.490840GHz detuned from 2.48832GHz by fcav/3. This produces a pulse train with a repetition rate that is three times the RF drive frequency (~7.42GHz) as shown in Fig. 6(a). Two arms of the dual-electrode modulator were equally biased at 7.558V (V bias1,V bias2≅1.51Vπ) from the condition acquired analytically in Section 2. Modulation amplitude of 4.335V (Vac=0.86V) was also determined from the analytical condition, Vac=0.86V. The RF spectrum for Fig. 6(a) is shown in Fig. 7(a). The frequency scale is 1GHz/div, and the amplitude scale is 2dB/div. The main peak indicates the frequency component at the pulse repetition rate, i.e., ~7.42GHz. There are also other frequency components in the RF spectrum. When the rational harmonic mode-locked pulse has a triple repetition rate, the peak amplitude repeats every three pulses. By controlling the applied voltages to each arm of the dual-electrode modulator, pulse-amplitude equalization was obtained. From the amplitude equalization conditions described in Section 2, the applied bias voltages and the modulation peak were extracted as V bias1=1.30Vπ, V bias2=1.40Vπ and Vac=1.01Vπ. The bias voltages and the modulation amplitude were then tuned around those values. One of the arms was biased with a voltage of 6.240V (V bias1≅1.25Vπ) and the other at 7.128V (V bias2≅1.43Vπ). In addition, the amplitude of the drive signals applied to two arms was increased from 4.335V (Vac≅0.86Vπ) to 5.097V (Vac≅1.02Vπ). A slight deviation of the experimental voltage values from the simulation results are mainly resulted from the minor tuning by fiber polarization control in order to obtain the best equalized pulse amplitude. Figure 6(b) shows that the pulse-amplitudes can be equalized using the unbalanced dual-drive Mach-Zehnder modulator. Figure 7(b) is the RF spectrum for Fig. 6(b), showing that all other frequency components except the 7.42GHz component were effectively suppressed. This verifies that the amplitude-equalized pulse train has a pure 7.42GHz frequency component that corresponds to the pulse repetition frequency. The suppression ratio of the signal power at 7.42GHz to the noise power level (other frequency components) appeared to be about 16dB without using any low-noise amplifiers after the high-speed photo detector. As shown in Fig. 6 and Fig. 7, the proposed method equalizes the uneven pulse-amplitude effectively while keeping the pulse repetition rate at three times the RF drive frequency.

Fig. 6. Measured optical pulse trains from the third (p=3) rational harmonic mode-locked semiconductor fiber ring laser (a) without and (b) with pulse-amplitude equalization.
Fig. 7. RF spectra of the optical pulse trains from the third (p=3) rational harmonic modelocked semiconductor fiber ring laser. (a) Without and (b) with pulse-amplitude equalization.
Fig. 8. Measured optical pulse trains from the fifth (p=5) rational harmonic mode-locked semiconductor fiber ring laser (a) without and (b) with pulse-amplitude equalization.

3.3. Fifth rational harmonic mode-locking (p=5)

The fifth rational harmonic mode-locking (p=5) was derived from the modulation frequency at 2.491609GHz by detuning from 2.48832GHz by fcav/5. Figure 8 shows the amplitude-equalized and -unequalized pulse trains in the fifth rational harmonic mode-locked semiconductor fiber laser. Figure 8(a) was obtained when the dual arms of the modulator were biased at the same voltage of 7.509V (V bias1,V bias2≅1.50Vπ) and equipped with the same amplitude signals of 4.14V (Vac≅0.83Vπ). The bias voltages of the two arms of the modulator were changed separately. One of the arms was biased at 6.855V (V bias1≅1.37Vπ) and the other at 7.998V (V bias2≅1.60Vπ). With an increase in the amplitudes of the drive signals applied to each arm from 4.14V (Vac≅0.83Vπ) to 5.263V (Vac≅1.05Vπ), the pulse-amplitudes were equalized. Figure 9 represents the RF spectrum of Fig. 8. The frequency scale is 1.5GHz/div, and the amplitude scale is 2dB/div. The main peak indicates the pulse repetition rate at about 12.34GHz. Three frequency components exist in Fig. 9(a). As shown in Fig. 9(b), the proposed pulse-amplitude equalization method suppressed the unwanted frequency components in the frequency domain. The suppression ratio of the 12.34GHz component power level to the noise power level is about 12dB. This result verifies that the proposed method effectively equalizes the uneven amplitudes of the fifth rational harmonic mode-locked pulse.

Fig. 9. RF spectra of the optical pulse trains from the fifth (p=5) rational harmonic mode-locked semiconductor fiber ring laser. (a) Without and (b) with pulse-amplitude equalization.

4. Conclusion

We have proposed and successfully demonstrated a novel pulse-amplitude equalization method using an unbalanced dual-drive LiNbO3 Mach-Zehnder modulator. The dual-drive modulator was used as a mode-locker and a pulse-amplitude equalizer in a rational harmonic mode-locked semiconductor fiber ring laser. The experimental results were consistent with the theoretical analysis. This is believed to be the simplest one in the pulse-amplitude equalization methods of higher order (>2) rational harmonic mode-locking. Only, the equalized rational harmonic order can be limited by the available amplitudes of the applying voltages. This can be utilized as a short optical pulse source with high repetition rate as required in high-speed OTDM systems.

Acknowledgement

This workwas partially supported by grant No. R01-2001-000-00327-0 from the Basic Program of the Korea Science & Engineering Foundation and also by the Brain Korea 21 project in Korea.

References and links

1.

C. Wu and N. K. Dutta, “High-repetition-rate optical pulse generation using a rational harmonic mode-locking fiber laser,” IEEE J. Quantum Electron. 36, 145–150 (2000). [CrossRef]

2.

N. Onodera, A. J. Lowery, L. Zhai, Z. Ahmed, and R. S. Tucker, “Frequency multiplication in actively mode-locked semiconductor lasers,” Appl. Phys. Lett. 62, 1329–1331 (1993). [CrossRef]

3.

Z. Ahmed and N. Onodera, “High repetition rate optical pulse generation by frequency mudltiplication in actively modelocked fibre ring lasers,” Electron. Lett. 32, 455–457 (1996). [CrossRef]

4.

M. -Y. Jeon, H. K. Lee, J. T. Ahn, K. H. Kim, D. S. Lim, and E. -H. Lee, “Pulse-amplitude-equalized output from a rational harmonic mode-locked fiber laser,” Opt. Lett. 23, 855–857 (1998). [CrossRef]

5.

H. J. Lee, K. Kim, and H. G.. Kim, “Pulse-amplitude equalization of rational harmonic mode-locked fiber laser using a semiconductor optical amplifier loop mirror,” Opt. Commun. 160, 51–56 (1999). [CrossRef]

6.

Z. Li, C. Lou, K. T. Chan, Y. Li, and Y. Gao, “Theoretical and Experimental Study of Pulse-Amplitude-Equalization in a Rational Harmonic Mode-Locked Fiber Ring Laser,” IEEE J. Quantum Electron. 37, 33–37 (2001). [CrossRef]

7.

C. G. Lee, Y. J. Kim, H. K. Choi, and C. -S. Park, “Pulse-amplitude equalization in a rational harmonic mode-locked semiconductor ring laser using optical feedback,” Opt. Commun. 209, 417–425 (2002). [CrossRef]

8.

G. Zhu, H. Chen, and N. Dutta, “Time domain analysis of a rational harmonic mode locked ring fiber laser,” J. Appl. Phys. 90, 2143–2147 (1990). [CrossRef]

9.

A. Takada and H. Miyazawa, “30GHz picosecond pulse generation from actively mode-locked erbium-doped fibre laser,” Electron. Lett. 26, 216–217 (1990). [CrossRef]

10.

S. Walklin and J. Conradi, “Effect of Mach-Zehnder Modulator DC Extinction Ratio on Residual Chirp-Induced Dispersion in 10-Gb/s Binary and AM-PSK Duobinary Lightwave Systems,” IEEE Photon. Technol. Lett. 9, 1400–1402 (1997). [CrossRef]

OCIS Codes
(060.2330) Fiber optics and optical communications : Fiber optics communications
(140.3560) Lasers and laser optics : Lasers, ring
(140.4050) Lasers and laser optics : Mode-locked lasers
(250.5980) Optoelectronics : Semiconductor optical amplifiers
(320.5550) Ultrafast optics : Pulses

ToC Category:
Research Papers

History
Original Manuscript: December 22, 2003
Revised Manuscript: February 27, 2004
Published: March 8, 2004

Citation
Yun Kim, Chung Lee, Young Chun, and Chang-Soo Park, "Pulse-amplitude equalization in a rational harmonic mode-locked semiconductor fiber ring laser using a dual-drive Mach-Zehnder modulator," Opt. Express 12, 907-915 (2004)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-12-5-907


Sort:  Journal  |  Reset  

References

  1. C. Wu and N. K. Dutta, �??High-repetition-rate optical pulse generation using a rational harmonic mode-locking fiber laser,�?? IEEE J. Quantum Electron. 36, 145�??150 (2000). [CrossRef]
  2. N. Onodera, A. J. Lowery, L. Zhai, Z. Ahmed, and R. S. Tucker, �??Frequency multiplication in actively mode-locked semiconductor lasers,�?? Appl. Phys. Lett. 62, 1329�??1331 (1993). [CrossRef]
  3. Z. Ahmed and N. Onodera, �??High repetition rate optical pulse generation by frequency mudltiplication in actively modelocked fibre ring lasers,�?? Electron. Lett. 32, 455�??457 (1996). [CrossRef]
  4. M. -Y. Jeon, H. K. Lee, J. T. Ahn, K. H. Kim, D. S. Lim, and E. -H. Lee, �??Pulse-amplitude-equalized output from a rational harmonic mode-locked fiber laser,�?? Opt. Lett. 23, 855�??857 (1998). [CrossRef]
  5. H. J. Lee, K. Kim, H. G. Kim, �??Pulse-amplitude equalization of rational harmonic mode-locked fiber laser using a semiconductor optical amplifier loop mirror,�?? Opt. Commun. 160, 51�??56 (1999). [CrossRef]
  6. Z. Li, C. Lou, K. T. Chan, Y. Li, and Y. Gao, �??Theoretical and Experimental Study of Pulse-Amplitude-Equalization in a Rational Harmonic Mode-Locked Fiber Ring Laser,�?? IEEE J. Quantum Electron. 37, 33�??37 (2001). [CrossRef]
  7. C. G. Lee, Y. J. Kim, H. K. Choi, C. -S. Park, �??Pulse-amplitude equalization in a rational harmonic mode-locked semiconductor ring laser using optical feedback,�?? Opt. Commun. 209, 417�??425 (2002). [CrossRef]
  8. G. Zhu, H. Chen, and N. Dutta, �??Time domain analysis of a rational harmonic mode locked ring fiber laser,�?? J. Appl. Phys. 90, 2143�??2147 (1990). [CrossRef]
  9. A. Takada and H. Miyazawa, �??30GHz picosecond pulse generation from actively mode-locked erbium-doped fibre laser,�?? Electron. Lett. 26, 216�??217 (1990). [CrossRef]
  10. S.Walklin and J. Conradi, �??Effect of Mach-Zehnder Modulator DC Extinction Ratio on Residual Chirp-Induced Dispersion in 10-Gb/s Binary and AM-PSK Duobinary Lightwave Systems,�?? IEEE Photon. Technol. Lett. 9, 1400�??1402 (1997). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited