OSA's Digital Library

Optics Express

Optics Express

  • Editor: Michael Duncan
  • Vol. 13, Iss. 10 — May. 16, 2005
  • pp: 3594–3599

Optics InfoBase > Optics Express > Volume 13 > Issue 10 > Page 3594

« Show journal navigation

Dispersion of nonlinear refraction and two-photon absorption using a white-light continuum Z-scan

Mihaela Balu, Joel Hales, David Hagan, and Eric Van Stryland  »View Author Affiliations


Optics Express, Vol. 13, Issue 10, pp. 3594-3599 (2005)
http://dx.doi.org/10.1364/OPEX.13.003594


View Full Text Article

Acrobat PDF (138 KB)


Advanced Search

Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We use a white-light continuum (WLC) Z-scan technique to measure the degenerate two-photon absorption spectrum and associated dispersion of the nonlinear refraction in ZnSe. The spectral components of the WLC source are separated by using a narrow band variable filter to minimize nondegenerate nonlinearities. We observe a change in sign of the ultrafast nonlinear refractive index around 0.7 of the bandgap energy as predicted by theory.

© 2005 Optical Society of America

1. Introduction

Specific applications require nonlinear properties of materials to be known over a broad wavelength range. The database for the spectral dependence of the nonlinear absorption and nonlinear refraction of materials is sparse. The methods for measuring nonlinearities are often time consuming and prone to errors of interpretation. For example, distinguishing ultrafast nonlinearities such as two-photon absorption, 2PA, from cumulative nonlinearities of, for example, excited-state absorption; or distinguishing bound-electronic nonlinear refraction from free-carrier refraction, can be difficult. Key to our understanding of these nonlinearities in many materials is the development of a large and reliable database of nonlinear spectral properties. For example, the spectral properties are of importance for determining structure-property trends in organic materials, where knowledge of the wavelengths of the peaks of the nonlinearities is important. Here we introduce a method for very rapid and simultaneous determination of both the spectrum of nonlinear absorption (NLA) and dispersion of nonlinear refraction (NLR).

Recently, a WLC was used as an intense source to measure degenerate 2PA over a broad spectral range [1

G.S. He, T.C Lin, P.N. Prasad, R. Kannan, R.A. Vaia, and L.S. Tan, “New technique for degenerate two-photon absorption spectral measurements using femtosecond continuum generation,” Opt. Express 10, 566 (2002), http://www.opticsexpress.org/abstract.cfm?URI=OPEX-10-13-566 [PubMed]

]. We then introduced the “WLC Z-scan” as a method for rapid and broadband characterization of the degenerate NLA and NLR and we demonstrated this method for NLA [2

M. Balu, J. Hales, D.J. Hagan, and E.W. Van Stryland, “White-light continuum Z-scan technique for nonlinear material characterization,” Opt. Express 12, 3820 (2004), http://www.opticsexpress.org/abstract.cfm?URI=OPEX-12-16-3820 [CrossRef] [PubMed]

]. At nearly the same time the authors of reference [3

L. De Boni, A.A. Andrade, L. Misoguti, C.R. Mendoca, and S.C. Zilio, “Z-scan measurements using femtosecond continuum generation,” Opt. Express 12, 3921 (2004), http://www.opticsexpress.org/abstract.cfm?URI=OPEX-12-17-3921 [CrossRef] [PubMed]

] introduced a similar technique that required a separate calibration and ignored nondegenerate 2PA. In our method an intense, broadband, WLC was used to replace the single wavelength source that is conventionally used in a Z-scan experiment. A glass prism and a ZnSe window were employed to spatially and temporally separate the spectral components of the WLC source before entering the nonlinear sample to minimize the nondegenerate 2PA process, which we found was significant in the absence of such separation. To confirm the validity of the method, we measured the degenerate 2PA spectrum of ZnSe. The experimental results showed good agreement with theory [4

E.W. Van Stryland, M.A. Woodall, H. Vanherzeele, and M.J. Soileau, “Energy band-gap dependence of two-photon absorption,” Opt. Lett. 10, 490 (1985) [CrossRef] [PubMed]

] and with our previous measurements at specific wavelengths, verifying the validity of our method.

In this paper, we demonstrate that the method can be extended to the “closed aperture” Z-scan for NLR measurements. As in the above 2PA measurements, simultaneous NLR measurements at all wavelengths would also require separation of the wavelengths to minimize nondegenerate nonlinearities. However, spatial separation presents difficulties in using the aperture needed for closed aperture Z-scans. Temporal dispersion of the continuum can broaden the pulses and may significantly reduce the irradiance, thus weakening the nonlinear signal. Here we present an alternative approach for both NLA and NLR, where we separate the WLC wavelengths with a variable frequency bandpass thin-film filter. This “linear variable filter” (LVF) method provides an absolute measurement of the degenerate nonlinearities of the sample under investigation with the high sensitivity of the normal Z-scan technique [5

T. Xia, D.J. Hagan, M. Sheik-Bahae, and E.W. Van Stryland, “Eclipsing Z-scan measurement of λ/104 wave-front distorsion,” Opt. Lett. 19, 317 (1994) [CrossRef] [PubMed]

]. To confirm its validity, we test this new procedure on the well-characterized semiconductor, ZnSe [4

E.W. Van Stryland, M.A. Woodall, H. Vanherzeele, and M.J. Soileau, “Energy band-gap dependence of two-photon absorption,” Opt. Lett. 10, 490 (1985) [CrossRef] [PubMed]

,6

M. Sheik-Bahae, A.A. Said, T.H. Wei, D.J. Hagan, and E.W. Van Stryland, “Sensitive measurement of optical nonlinearities using a single beam,” IEEE J. Quantum Electron. 26, 760(1990) [CrossRef]

,7

R. Negres, J. Hales, A. Kobyakov, D. J. Hagan, and E. W. Van Stryland, “Experiment and analysis of two-photon absorption spectroscopy using a white-light continuum probe,” IEEE J.Quantum Electron. 38, 1205 (2002) [CrossRef]

,8

M. Sheik-Bahae, D.C. Hutchings, D.J. Hagan, and E.W. Van Stryland, “Dispersion of bound electronic nonlinear refraction in solids,” IEEE J.Quantum Electron. 27, 1296 (1991) [CrossRef]

]. We demonstrate the use of this technique for simultaneous measurement of both NLA and NLR.

2. Experiment: method and results

We used a regeneratively amplified femtosecond laser system which provides laser pulses at 775 nm of 150 fs (FWHM) duration, with an energy of 1 mJ/pulse at a 1 kHz repetition rate.

For WLC generation, we focused ~10µJ of this beam with an f=15 cm lens into a 3 cm long cell filled with distilled water. A short-pass filter was used to remove the 775 nm pump and the infrared part of the continuum. The spectrum of the WLC after passing through the low-pass filter is shown in Fig. 1.

Fig. 1. WLC spectrum after passing through the low-pass filter

To avoid nonlinear processes such as nondegenerate 2PA, cross-phase modulation, etc., we spectrally separate the WLC wavelengths with a narrowband LVF, manufactured by Ocean Optics, Inc.[9

http://www.oceanoptics.com/Products/linearvariablefilters.asp

]. This acts as a bandpass filter with spatially-varying center wavelength. The bandpass width can also be varied. By focusing the WLC beam through the filter we were able to obtain a transmitted beam having a spectral bandwidth of 12–15 nm (FWHM) over the wavelength range 500 to 710 nm. To obtain Z-scans over this wavelength range, at each Z-position we scan the full wavelength range by translating the LVF through the beam. The sample is translated along Z after each wavelength scan, and the process is repeated until the entire Z-scan is obtained. In practice, we use two computer driven translation stages and, at the 1 kHz laser pulse repetition rate, averaging 500 pulses per data point, a single experiment takes ~8 minutes to give the full spectrum of NLA and full dispersion of NLR. The experimental setup is shown in Fig. 2. After the WLC beam is focused onto the LVF, the single wavelength beam transmitted by the LVF is approximately recollimated, then divided by a beamsplitter into a reference arm and a signal arm. After focusing the beam through the sample, we use a second beamsplitter, to split the transmitted beam into two arms. On one arm, we use a lens to collect all the energy on the detector (“open aperture” Z-scan). On the other arm we place an aperture which transmits only ~40% of the beam (“closed aperture” Z-scan). Nonlinear absorption coefficients are extracted from the transmission curves obtained in the open aperture experimental arm. The experimental curves obtained in the closed aperture arm contain information about both nonlinear absorption and nonlinear refraction. It was shown in reference [6

M. Sheik-Bahae, A.A. Said, T.H. Wei, D.J. Hagan, and E.W. Van Stryland, “Sensitive measurement of optical nonlinearities using a single beam,” IEEE J. Quantum Electron. 26, 760(1990) [CrossRef]

] that, for small signals, the separation of the nonlinear refraction from 2PA can be done by dividing the closed aperture normalized Z-scan by the open aperture one.

To fit the Z-scan transmission curves corresponding to open [6

M. Sheik-Bahae, A.A. Said, T.H. Wei, D.J. Hagan, and E.W. Van Stryland, “Sensitive measurement of optical nonlinearities using a single beam,” IEEE J. Quantum Electron. 26, 760(1990) [CrossRef]

] and closed [10

M. Sheik-Bahae, A.A. Said, and E.W. Van Stryland, “High-sensitivity, single-beam n2 measurements,” Opt.Lett. 14, 955 (1989) [CrossRef] [PubMed]

] apertures, we need to know the energy, the beam waist and the pulsewidth for each spectral component. The energies measured were in the range of 0.3–2 nJ over the range 500 nm–710 nm. We determined the beam waist for different wavelengths transmitted by the LVF by using the knife-edge scanning technique. For pulsewidth measurements we used an Optical Kerr Gate experiment (OKG) [11

S. Yamaguchi and H. Hamaguchi, “Convenient method of measuring the chirp structure of femtosecond white-light continuum pulses,” Appl. Spectrosc. 49, 1513 (1995) [CrossRef]

], where the Kerr medium was a 1mm thick cell filled with CCl4. From the width of the cross-correlation traces we were able to determine the pulsewidth for different wavelengths transmitted by the LVF. The value determined was ~165 fs FWHM in the range 500 nm–750 nm.

In order to test this technique we measured the 2PA spectrum and the associated bound electronic n2 dispersion in ZnSe. We chose ZnSe since we had measured its 2PA and n2 at several wavelengths previously [4

E.W. Van Stryland, M.A. Woodall, H. Vanherzeele, and M.J. Soileau, “Energy band-gap dependence of two-photon absorption,” Opt. Lett. 10, 490 (1985) [CrossRef] [PubMed]

,6

M. Sheik-Bahae, A.A. Said, T.H. Wei, D.J. Hagan, and E.W. Van Stryland, “Sensitive measurement of optical nonlinearities using a single beam,” IEEE J. Quantum Electron. 26, 760(1990) [CrossRef]

,8

M. Sheik-Bahae, D.C. Hutchings, D.J. Hagan, and E.W. Van Stryland, “Dispersion of bound electronic nonlinear refraction in solids,” IEEE J.Quantum Electron. 27, 1296 (1991) [CrossRef]

]. The thickness of the sample was 2.0 mm for which the thin sample approximation for diffraction is valid [6

M. Sheik-Bahae, A.A. Said, T.H. Wei, D.J. Hagan, and E.W. Van Stryland, “Sensitive measurement of optical nonlinearities using a single beam,” IEEE J. Quantum Electron. 26, 760(1990) [CrossRef]

]. However, ZnSe has a large group velocity dispersion (GVD) and we must account for GVD-induced pulsewidth broadening as the pulse passes through the ZnSe sample. To measure the effect of the GVD on the pulsewidth in the ZnSe, we repeated the OKG experiment with the sample placed in the WLC path. This revealed that the broadening was significant, increasing the pulse width from 165 fs FWHM to 260 fs at 710 nm and from 165 fs to 400 fs at 560 nm.

In order to analyze the Z-scan we need to determine the irradiance within the sample. For this, we begin with the experimentally measured pulsewidths without and with the ZnSe in the beam (corresponding respectively to the pulsewidths at the front and at the back of the sample). We then compare the experimental value after the ZnSe sample with that obtained from the following theoretical calculation. Considering the pulse entering the sample to be linearly up-chirped, we can calculate the chirp parameter from its spectral width (determined from the spectrometer) and its pulsewidth (obtained from the OKG measurement). The pulsewidth at the output of the sample is then calculated by taking into account the GVD induced pulse broadening. The experimental pulsewidths were between 8% and 17% longer than theoretical, with an average difference of 14% at all wavelengths. Therefore, to obtain a good value for the average irradiance within the sample, we average the experimentally measured input pulsewidth with the calculated output multiplied by 1.14, i.e. (τinput+1.14τoutput)/2. We used the average value of 1.14 because we measured the effect of broadening due to ZnSe for only 4 wavelengths.

Fig. 2. WLC Z-scan experimental setup. CPA-2001-femtosecond laser source; WP-waveplate; P-polarizer; L-lens; LVF-linear variable filter; M-mirror; BS-beamsplitter; S-sample; A-aperture; D-detector

The experimental Z-scan curves (open aperture and its corresponding divided closed aperture) are shown in Fig. 3 for two different wavelengths.

Fig. 3. Z-scan data at 580nm and 710nm a) open aperture and b) closed aperture (the result of the division with open aperture). Here each data point is the average of 500 pulses.

The solid lines represent fits [6

M. Sheik-Bahae, A.A. Said, T.H. Wei, D.J. Hagan, and E.W. Van Stryland, “Sensitive measurement of optical nonlinearities using a single beam,” IEEE J. Quantum Electron. 26, 760(1990) [CrossRef]

,10

M. Sheik-Bahae, A.A. Said, and E.W. Van Stryland, “High-sensitivity, single-beam n2 measurements,” Opt.Lett. 14, 955 (1989) [CrossRef] [PubMed]

] to the experimental curves used to extract values of the 2PA coefficient, β (from the open-aperture Z-scan curves) and the values of the nonlinear refractive index, n2 (from the closed-aperture Z-scan curves). We notice that n2 changes sign from negative at 580 nm to positive at 710 nm, as predicted by theory in reference [8

M. Sheik-Bahae, D.C. Hutchings, D.J. Hagan, and E.W. Van Stryland, “Dispersion of bound electronic nonlinear refraction in solids,” IEEE J.Quantum Electron. 27, 1296 (1991) [CrossRef]

]. To our knowledge, this is the first time the sign change of n2 around 0.7 of the energy bandgap has been demonstrated by tuning the wavelength. The values of β and n2 obtained from fits at different wavelengths are presented in Fig. 4 along with the theoretical predictions of references 4 and 8. The β values have an estimated experimental error of approximately 20%. The errors for n2 values are between ±30% and ±80%, the larger errors corresponding to the n2 values close to zero as the transmittance curves were quite noisy.

Fig. 4. a) 2PA coefficient and b) nonlinear refractive index coefficient obtained from theory and from the experimental data fittings

3. Conclusion and future work

We have proposed and demonstrated a sensitive method for rapid and simultaneous characterization of a material’s degenerate nonlinear absorption spectrum and the dispersion of its nonlinear refraction. We experimentally verified the method on the well-characterized semiconductor, ZnSe. The good agreement between experimental results and theoretical calculations for the 2PA spectrum and n2 dispersion attests to the potential of this technique. Extension of this technique to materials with considerably smaller nonlinearities will require higher spectral energy densities for the WLC. High energy WLC sources have already been demonstrated [13

A.K. Dharmadhikari, F.A. Rajgara, N.C.S. Reddy, A.S. Sandhu, and D. Mathur, “Highly efficient white light generation from barium fluoride,” Opt. Express 12, 695 (2004) http://www.opticsexpress.org/abstract.cfm?URI=OPEX-12-4-695 [CrossRef] [PubMed]

], but unfortunately, above a certain threshold, the beam breaks into small filaments making a Z-scan experiment impossible. A promising possibility is to use a WLC generated in hollow fibers which appears to exhibit both high spectral energy densities and good spatial properties [14

Private communication, Alex Gaeta, Cornel University

, 15

K. Sokolowski-Tinten, K. Werner, M. Zhou, and D. Von Der Linde, “Femtosecond continuum generation using a gas-filled hollow fiber”, CLEO Conference, Baltimore, May 23–28, 1999

].

Also, linear variable filters that operate in different spectral regions will allow for measurements over a broader spectrum, thus helping to complete the database of the spectral dependence of the degenerate nonlinear absorption and refraction of materials.

The results of this method when combined with data from our WLC femtosecond pump-probe method [7

R. Negres, J. Hales, A. Kobyakov, D. J. Hagan, and E. W. Van Stryland, “Experiment and analysis of two-photon absorption spectroscopy using a white-light continuum probe,” IEEE J.Quantum Electron. 38, 1205 (2002) [CrossRef]

] yielding the nondegenerate nonlinear absorption with temporal information, give us a very complete picture of the nonlinear absorptive and refractive properties of a material.

Acknowledgments

We gratefully acknowledge the support of the National Science Foundation ECS 0217932 and the US Army Research Laboratory.

References

1.

G.S. He, T.C Lin, P.N. Prasad, R. Kannan, R.A. Vaia, and L.S. Tan, “New technique for degenerate two-photon absorption spectral measurements using femtosecond continuum generation,” Opt. Express 10, 566 (2002), http://www.opticsexpress.org/abstract.cfm?URI=OPEX-10-13-566 [PubMed]

2.

M. Balu, J. Hales, D.J. Hagan, and E.W. Van Stryland, “White-light continuum Z-scan technique for nonlinear material characterization,” Opt. Express 12, 3820 (2004), http://www.opticsexpress.org/abstract.cfm?URI=OPEX-12-16-3820 [CrossRef] [PubMed]

3.

L. De Boni, A.A. Andrade, L. Misoguti, C.R. Mendoca, and S.C. Zilio, “Z-scan measurements using femtosecond continuum generation,” Opt. Express 12, 3921 (2004), http://www.opticsexpress.org/abstract.cfm?URI=OPEX-12-17-3921 [CrossRef] [PubMed]

4.

E.W. Van Stryland, M.A. Woodall, H. Vanherzeele, and M.J. Soileau, “Energy band-gap dependence of two-photon absorption,” Opt. Lett. 10, 490 (1985) [CrossRef] [PubMed]

5.

T. Xia, D.J. Hagan, M. Sheik-Bahae, and E.W. Van Stryland, “Eclipsing Z-scan measurement of λ/104 wave-front distorsion,” Opt. Lett. 19, 317 (1994) [CrossRef] [PubMed]

6.

M. Sheik-Bahae, A.A. Said, T.H. Wei, D.J. Hagan, and E.W. Van Stryland, “Sensitive measurement of optical nonlinearities using a single beam,” IEEE J. Quantum Electron. 26, 760(1990) [CrossRef]

7.

R. Negres, J. Hales, A. Kobyakov, D. J. Hagan, and E. W. Van Stryland, “Experiment and analysis of two-photon absorption spectroscopy using a white-light continuum probe,” IEEE J.Quantum Electron. 38, 1205 (2002) [CrossRef]

8.

M. Sheik-Bahae, D.C. Hutchings, D.J. Hagan, and E.W. Van Stryland, “Dispersion of bound electronic nonlinear refraction in solids,” IEEE J.Quantum Electron. 27, 1296 (1991) [CrossRef]

9.

http://www.oceanoptics.com/Products/linearvariablefilters.asp

10.

M. Sheik-Bahae, A.A. Said, and E.W. Van Stryland, “High-sensitivity, single-beam n2 measurements,” Opt.Lett. 14, 955 (1989) [CrossRef] [PubMed]

11.

S. Yamaguchi and H. Hamaguchi, “Convenient method of measuring the chirp structure of femtosecond white-light continuum pulses,” Appl. Spectrosc. 49, 1513 (1995) [CrossRef]

12.

M. Sheik-Bahae, A.A. Said, and E.W. Van Stryland, “High-sensitivity, single-beam n2 measurements,” Opt. Lett. 14, 955 (1989) [CrossRef] [PubMed]

13.

A.K. Dharmadhikari, F.A. Rajgara, N.C.S. Reddy, A.S. Sandhu, and D. Mathur, “Highly efficient white light generation from barium fluoride,” Opt. Express 12, 695 (2004) http://www.opticsexpress.org/abstract.cfm?URI=OPEX-12-4-695 [CrossRef] [PubMed]

14.

Private communication, Alex Gaeta, Cornel University

15.

K. Sokolowski-Tinten, K. Werner, M. Zhou, and D. Von Der Linde, “Femtosecond continuum generation using a gas-filled hollow fiber”, CLEO Conference, Baltimore, May 23–28, 1999

OCIS Codes
(190.4400) Nonlinear optics : Nonlinear optics, materials
(300.6420) Spectroscopy : Spectroscopy, nonlinear

ToC Category:
Research Papers

History
Original Manuscript: March 24, 2005
Revised Manuscript: April 27, 2005
Published: May 16, 2005

Citation
Mihaela Balu, Joel Hales, David Hagan, and Eric Van Stryland, "Dispersion of nonlinear refraction and two-photon absorption using a white-light continuum Z-scan," Opt. Express 13, 3594-3599 (2005)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-13-10-3594


Sort:  Journal  |  Reset  

References

  1. G.S.He, T.C Lin, P.N. Prasad, R.Kannan, R.A. Vaia and L.S. Tan, “New technique for degenerate two-photon absorption spectral measurements using femtosecond continuum generation,” Opt. Express 10, 566 (2002). [PubMed]
  2. M.Balu, J.Hales, D.J.Hagan, E.W. Van Stryland, “White-light continuum Z-scan technique for nonlinear material characterization,” Opt. Express 12, 3820 (2004). [CrossRef] [PubMed]
  3. L.De Boni, A.A.Andrade, L.Misoguti, C.R.Mendoca and S.C.Zilio, “Z-scan measurements using femtosecond continuum generation,” Opt. Express 12, 3921 (2004) [CrossRef] [PubMed]
  4. E.W.Van Stryland, M.A. Woodall, H.Vanherzeele and M.J.Soileau, “Energy band-gap dependence of two-photon absorption,” Opt. Lett. 10, 490 (1985) [CrossRef] [PubMed]
  5. T. Xia, D.J.Hagan, M.Sheik-Bahae, E.W.Van Stryland, “Eclipsing Z-scan measurement of λ/10^4 wave-front distorsion,” Opt. Lett. 19, 317 (1994) [CrossRef] [PubMed]
  6. M.Sheik-Bahae, A.A.Said, T.H.Wei, D.J.Hagan and E.W. Van Stryland, “Sensitive measurement of optical nonlinearities using a single beam,” IEEE J. Quantum Electron. 26, 760 (1990) [CrossRef]
  7. R. Negres, J. Hales, A. Kobyakov, D. J. Hagan and E. W. Van Stryland, “Experiment and analysis of two-photon absorption spectroscopy using a white-light continuum probe,” IEEE J.Quantum Electron. 38, 1205 (2002) [CrossRef]
  8. M. Sheik-Bahae, D.C. Hutchings, D.J. Hagan, E.W. Van Stryland, “Dispersion of bound electronic nonlinear refraction in solids,” IEEE J. Quantum Electron. 27, 1296 (1991) [CrossRef]
  9. http://www.oceanoptics.com/Products/linearvariablefilters.asp
  10. M.Sheik-Bahae, A.A.Said and E.W. Van Stryland, “High-sensitivity, single-beam n2 measurements,” Opt. Lett. 14, 955 (1989) [CrossRef] [PubMed]
  11. S.Yamaguchi and H. Hamaguchi, “Convenient method of measuring the chirp structure of femtosecond white-light continuum pulses,” Appl. Spectrosc. 49, 1513 (1995) [CrossRef]
  12. M.Sheik-Bahae, A.A.Said and E.W. Van Stryland, “High-sensitivity, single-beam n2 measurements,” Opt. Lett. 14, 955 (1989) [CrossRef] [PubMed]
  13. A.K.Dharmadhikari, F.A.Rajgara, N.C.S.Reddy, A.S.Sandhu and D.Mathur, “Highly efficient white light generation from barium fluoride,” Opt. Express 12, 695 (2004). [CrossRef] [PubMed]
  14. Private communication, Alex Gaeta, Cornel University
  15. K. Sokolowski-Tinten, K. Werner, M. Zhou and D. Von Der Linde, “Femtosecond continuum generation using a gas-filled hollow fiber”, CLEO Conference, Baltimore, May 23-28, 1999

Cited By

 Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1. Fig. 2. Fig. 3.
 
Fig. 4.
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited