OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 15, Iss. 5 — Mar. 5, 2007
  • pp: 2369–2374
« Show journal navigation

Injection mode-locked guide star laser concept and design verification experiments

Thomas P. Rutten, Peter J. Veitch, Céline d’Orgeville, and Jesper Munch  »View Author Affiliations


Optics Express, Vol. 15, Issue 5, pp. 2369-2374 (2007)
http://dx.doi.org/10.1364/OE.15.002369


View Full Text Article

Acrobat PDF (140 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

Injection mode-locking combined with stretched Q-switching of a ring resonator are proposed and demonstrated as a promising approach for advanced, guide star lasers. The concept uses two Nd:YAG lasers, producing a macro-micro pulse-burst output, optimized for efficient sum-frequency generation. We demonstrate wavelength, bandwidth and timing control required to maximize the atmospheric Na fluorescence.

© 2007 Optical Society of America

1. Introduction

The use of lasers to create artificial guide stars for adaptive optics is currently revolutionizing ground based astronomy by permitting correction of the optical aberrations due to the atmosphere and allowing near diffraction limited performance of large aperture, ground based telescopes when no natural guide star is available near the science object [1

1. P. W. Milonni, “Resource letter: AOA-1: Adaptive optics for astronomy,” Am. J. Phys. 67, 476 (1999). [CrossRef]

, 2

2. N. Ageorges and C. Dainty, Laser Guide Star Adaptive Optics for Astronomy (Kluwer Academic Publishers, 2000).

]. Light emitted at 589 nm is used to excite sodium fluorescence in the upper atmosphere, thereby creating an artificial point-like source of light, or guide star, which can be used as a source for adaptive optics in a telescope to correct for aberrations in the intervening atmosphere. For extremely large ground based telescopes (ELTs) in the 30 m to 100 m diameter class [3

3. N. Hubin, B. L. Ellerbroek, R. Arsenault, R. M. Clare, R. Dekany, L. Gilles, M. Kasper, G. Herriot, M. Le Louarn, E. Marchetti, S. Oberti, J. Stoesz, J. P. Veran, and C. Vérinaud, “Adaptive optics for Extremely Large Telescopes,” in Proceedings IAU Symposium No. 232, 60–85 (2005).

], a single Na guide star does not provide sufficient sampling of the atmosphere [4

4. R. Foy and A. Labeyrie, “Feasibility of adaptive telescope with laser probe,” Astron. Astrophys. 152, 29 (1985).

] and a more complex approach is required using multiple laser guide stars distributed across the aperture of the telescope to allow tomography of the intervening atmospheric aberrations [2

2. N. Ageorges and C. Dainty, Laser Guide Star Adaptive Optics for Astronomy (Kluwer Academic Publishers, 2000).

]. This approach has resulted in the need to develop improved laser sources. There is thus a demand for increased power and improved pulse burst formats to maximize utility and efficiency [3

3. N. Hubin, B. L. Ellerbroek, R. Arsenault, R. M. Clare, R. Dekany, L. Gilles, M. Kasper, G. Herriot, M. Le Louarn, E. Marchetti, S. Oberti, J. Stoesz, J. P. Veran, and C. Vérinaud, “Adaptive optics for Extremely Large Telescopes,” in Proceedings IAU Symposium No. 232, 60–85 (2005).

]. The particular requirements for our work are summarized in Table 1 [5

5. Requirements from Gemini RFP no. N231397, Dec. 2003.

] and include a total optical power ≥ 50 W and a waveform consisting of pulses of duration less than 3 μs, operating at pulse repetition frequencies (PRF) up to 800 Hz. Furthermore, the emission must be exactly tunable to the D2 line of Na, and have a bandwidth that can be optimized between 1 GHz and 3 GHz to enable use of all the Doppler broadened Na available and maximize photon return [1

1. P. W. Milonni, “Resource letter: AOA-1: Adaptive optics for astronomy,” Am. J. Phys. 67, 476 (1999). [CrossRef]

]. Finally, engineering requirements of reliability, robustness and efficiency are important for applications of lasers to telescopes situated on remote mountain tops.

Table 1. Laser Performance Requirements

table-icon
View This Table

Approaches to the laser include the first generation dye lasers [6

6. C. E. Max, K. Avicola, J. M. Brase, H. W. Friedman, H. D. Bissinger, J. Duff, D. T. Gavel, J. A. Horton, R. Kiefer, J. R. Morris, S. S. Olivier, R. W. Presta, D. A. Rapp, J. T. Salmon, and K. E. Waltjen, “Design, layout, and early results of a feasibility experiment for sodium-layer laser-guide-star adaptive optics,” J. Opt. Soc. Am. A. 11, 813 (1994). [CrossRef]

], the more reliable sum-frequency generation (SFG) using solid state lasers [7

7. T. H. Jeys, A. A. Brailove, and A. Mooradian, “Sum frequency generation of sodium resonance radiation,” Appl. Opt. 28, 2588 (1989). [CrossRef] [PubMed]

,8

8. A. Tracy, A. Hankla, C. Lopez, D. Sadighi, N. Rogers, K. Groff, I. McKinnie, and C. d’Orgeville, “High-Power Solid-State Sodium Beacon Laser Guidestar for the Gemini North Observatory,” Proc. SPIE 5490, 998–1009 (2004). [CrossRef]

] and recently fiber lasers [9

9. D. M. Pennington, R. Beach, J. Dawson, A. Drobshoff, Z. Liao, S. Payne, D. Bonaccini, W. Hackenberg, and L. Taylor, “Compact fiber laser approach to generating 589 nm laser guide stars,” in Proceedings of Conference on Lasers and Electro-Optics Europe, 730 (2003).

,10

10. D. Bonaccini Calia, W. Hackenberg, C. Araujo, I. Guidolin, and J. L. Alvarez, “Laser guide star related activities at ESO,” Proc. SPIE 5490, 974–980 (2004). [CrossRef]

], combined with various laser waveform techniques ranging from cw to mode-locking [11

11. E. J. Kibblewhite and F. Shi, “Design and field test of an 8 watt sum-frequency laser for adaptive optics,” Proc. SPIE 3353, 300–309 (1998). [CrossRef]

]. However, to the best of our knowledge no single approach has fully satisfied all the requirements simultaneously. We have proposed a novel approach [12

12. Response to Gemini RFP no. N231397, Jan 2004.

, 13

13. T. P. Rutten, P. J. Veitch, and J. Munch, “Development of a Sodium Laser Guide Star for Astronomical Adaptive Optics Systems,” presented at the Australasian Conference on Optics, Lasers and Spectroscopy, Rotorua, New Zealand, 5–9 Dec. 2005.

] using injection mode- locking [14,15] that has the potential to satisfy the above requirements. The concept is summarized below and we also describe critical design verification experiments to demonstrate the viability of the concept.

2. Injection mode-locked guide star laser concept.

The overall concept is shown in Fig. 1. It uses two cw non planar ring oscillator (NPRO) lasers [17

17. T. J. Kane and R. L. Byer, “Monolithic, unidirectional single-mode Nd:YAG ring laser,” Opt. Lett. 10, 65 (1985). [CrossRef] [PubMed]

], each stabilized accurately to the wavelengths near 1064 nm and 1319 nm required to produce the Na wavelength by SFG [7

7. T. H. Jeys, A. A. Brailove, and A. Mooradian, “Sum frequency generation of sodium resonance radiation,” Appl. Opt. 28, 2588 (1989). [CrossRef] [PubMed]

]. For robust operation and control we propose using an active servo to accomplish this as shown, but in practice this may not be necessary due to the inherent stability of the NPROs [18

18. J. C. Bienfang, C. A. Denman, B. W. Grime, P. D. Hillman, G. T. Moore, and J. M. Telle, “20 W of continuous-wave sodium D2 resonance radiation from sum-frequency generation with injection-locked lasers,” Opt. Lett. 28, 2219 (2003). [CrossRef] [PubMed]

]. From the output of each of these cw lasers, we slice a pulse of about 1 ns duration to inject into the slave power resonator for injection mode-locking. Accurate control of the width of the injected pulse is used to control the bandwidth of the micro-pulses of the injection mode-locked output. Precise timing of the two injected pulses is required for efficient single-pass SFG. This is ensured by operating both pulse slicers in series from the same high voltage pulser, thus minimizing timing jitter between the 1064 nm and the 1319 nm micro-pulses.

Fig. 1. Overall design concept. Two cw NPRO lasers provide the absolute wavelength control and tuning, and synchronized pulse slicers provide timing and bandwidth control of injection mode-locked slave lasers for subsequent SFG at the Na wavelength.

3. Design verification experiments using a subscale, 1064nm laser.

3.1 Seed pulse production

To investigate bandwidth control by injection mode-locking, we have assembled a versatile pulsed seed source consisting of an NPRO master laser followed by two 50 ohm Pockels cells between linear polarizers. Two independent high voltage avalanche transistor pulsers are used to provide fast rise time (100 ps) electrical pulses to the Pockels cells. This setup allows complete control of the optical pulse width, by using one Pockels cell to turn on the pulse and the other to turn it off, with an adjustable time delay between the two events.

Using this pulse slicer, we have produced optical seed pulses of peak power up to 0.5 W, and pulse duration continuously adjustable between 1 ns and 200 ps, with examples shown in Fig. 2. The near-cw light rejected by the pulse slicer would be used to lock the master lasers to the sodium wavelength by cw SFG, if required. The jitter between the trigger of the high voltage pulse generators and the output of the mode-locked laser (see below) was measured, using a fast sampling oscilloscope, to be < 10 ps rms. This low jitter proves that timing of the output micro-pulses is determined by the input pulse, as required for efficient SFG of two mode-locked lasers, and allows for very precise control of the pulse width in our design verification experiments.

Fig. 2. Optical pulses of variable duration produced by our double Pockels cell switch.

3.2 Slave laser

The slave laser (Fig. 3) was assembled for use in the design verification experiments only. It uses a conduction cooled Nd:YAG zigzag slab, 4.00 mm x 4.32 mm x 36.14 mm, which is side pumped in the zigzag plane by pulsed semiconductor lasers. The laser makes use of a 3.5 m long ring oscillator incorporating a Q-switch, a thin film polarizer (TFP) for injection and extraction and a half wave plate (HWP). Together, these elements allow the efficient production of stretched Q-switched pulses [16

16. Australian Patent PCT/AU2006/ 001852, Dec. 2006.

]. Telescopes were included to provide resonator stability while creating a large size TEM00 mode (ω = 1.2 mm) inside the zigzag slab [19

19. D. C. Hanna, C. G. Sawyers, and M. A. Yuratich, “Telescopic resonators for large-volume TEM00-mode operation,” Opt. Quantum Electron. 13, 493 (1981). [CrossRef]

]. This configuration permits efficient extraction of the stored energy, avoids damage to optics from the high peak power micro-pulses and reduces the optical gain per round trip, which lengthens the output macro-pulse width [20

20. J. J. Degnan, “Theory of the Optimally Coupled Q-Switched Laser,” IEEE J. Quantum Electron. 25, 214 (1989). [CrossRef]

].

Fig. 3. Slave laser configuration, showing pulse injection into a traveling ring oscillator via a polarizing beam splitter (TFP), and the arrangement of polarizing elements (HWP) and Q-switch required to stretch the macro-pulse formed.

For injection mode-locking, a π-polarized seed pulse is injected into the resonator through the TFP. For the first pass, the seed pulse polarization is converted to σ by the HWP, and with no voltage applied to the Q-switch the seed pulse passes through without a change in polarization. It is thus completely reflected by the TFP and then converted to π polarization by the HWP. Voltage has meanwhile been applied to the Q-switch rotating the polarization back to σ thus trapping the pulse within the ring and enabling development of the giant pulse. Once the pulse has built up sufficiently, the voltage applied to the Q-switch is reduced slightly, allowing a controlled out-coupling fraction of the TFP. By varying this voltage the stretching of the output pulse can be controlled. Thus the Q-switch in our resonator produces no polarization rotation losses during build-up of the pulse and, instead of being opened completely to cavity dump the pulse as in conventional regenerative amplifiers [15

15. J. E. Murray and W. H. Lowdermilk, “ND:YAG regenerative amplifier,” J. Appl. Phys. 51, 3548 (1980). [CrossRef]

], it is used to stretch the output pulse. Due to the broad bandwidth of the injected seed pulse, no servo was required to keep the slave locked to the master oscillator.

3.3 Design verification results.

Initial experiments were done to investigate injection mode-locking with no pulse stretching. The slave laser produced a near diffraction limited (M2 = 1.06) 1064 nm beam. A typical output of the injection mode-locked slave resonator is shown in Fig. 4. The optimized output was 20 mJ per macro-pulse at 50 Hz PRF, limited by the pump lasers used. This is the energy per macropulse of a laser with average power of 16 W operating at 800 Hz PRF, and our initial result is thus already of significance to conventional laser guide star requirements. Each macro-pulse consists of more than 30 micro-pulses separated by 12 ns, the round trip time of the slave resonator. This could be adjusted in terms of the 16 ns Na fluorescence life time [1

1. P. W. Milonni, “Resource letter: AOA-1: Adaptive optics for astronomy,” Am. J. Phys. 67, 476 (1999). [CrossRef]

,7

7. T. H. Jeys, A. A. Brailove, and A. Mooradian, “Sum frequency generation of sodium resonance radiation,” Appl. Opt. 28, 2588 (1989). [CrossRef] [PubMed]

] to minimize bleaching and thus optimize the photon return from the guide star. The waveform shown was obtained on every pulse without the need for any feedback to the slave oscillator and it was observed that the shape of each micro-pulse from the slave laser closely resembled that of the input seed pulse.

Fig. 4. A single macro-micro pulse output, consisting of a train of injection mode-locked micro-pulses. The time scale is 50 ns per half cm, or 0.9μs across the whole picture.

The input pulse width was measured using a sampling oscilloscope and a fast detector with an overall detection bandwidth of 12 GHz, with typical seed pulse shapes obtained as shown in Fig. 2. The bandwidth of the output of the slave laser was measured by integrating the output of a scanning Fabry-Perot interferometer over many macro-pulses. An example of one of these bandwidth measurements is shown in Fig. 5(a). While the resolution of the Fabry-Perot is 40 MHz, longitudinal laser modes can not be resolved in this figure due to the drift of modes within the envelope of the lasers spectrum, caused by changes in the slave cavity length from thermal expansion. The irregular shape of the spectrum is believed due to the irregular shape of the injected seed pulse (Fig. 2). A plot of the FWHM of a Gaussian fit to each spectrum is shown as a function of the injected seed pulse width in Fig. 5(b). We thus succeeded in controlling the bandwidth of the output from 0.8 GHz to 2.3 GHz. The bandwidth of the final SFG is expected to be approximately twice that of the fundamental wavelengths [7

7. T. H. Jeys, A. A. Brailove, and A. Mooradian, “Sum frequency generation of sodium resonance radiation,” Appl. Opt. 28, 2588 (1989). [CrossRef] [PubMed]

] and the results obtained thus essentially satisfy the system requirements. It is not expected to be difficult to modify the temporal shape of the seed pulse or to increase its duration slightly if a lower bandwidth is desired.

The BBO Q-switch was driven by a specially designed pulser, capable of pulse stretching as discussed. Excellent throttled Q-switching and resulting macro-pulse stretching with no loss in pulse energy was achieved as shown in Fig. 6. The tendency towards a flat top envelope will facilitate subsequent SFG optimization.

Fig. 5. (a). Spectrum of the slave output corresponding to a seed pulse width of 760 ps. The FWHM bandwidth is 1.3 GHz. (b) Plot of measurements of slave laser bandwidth versus the width of the seed pulse. The curve is a fit to the data with a time-bandwidth product of 0.91 as shown.
Fig. 6. Example of a stretched macro-pulse, 10 mJ per pulse, 50 Hz. The un-stretched macro-pulse in this case is similar to Fig. 4, but with FWHM width of 300ns.

4. Discussion and conclusion

We have proposed a new concept for sodium guide star lasers that appears to satisfy most critical requirements for planned telescope designs. Our design verification experiments have demonstrated the viability of our approach, including demonstrating a preferred pulse burst waveform, detailed bandwidth control, wavelength control and low timing jitter. Additional work is in progress to demonstrate the concept at 1319 nm and to optimize the concept at the power and wavelengths for the Na guide star. This optimization will include a simplified pulse slicer, optimized laser sources, the possible use of additional laser power amplifiers and optimized SFG. Detailed designs and proof of concept experiments for our approach remain to be done, but some critical design issues have already been demonstrated by others such as the operation of simple extra cavity SFG using mode-locked pump lasers [11

11. E. J. Kibblewhite and F. Shi, “Design and field test of an 8 watt sum-frequency laser for adaptive optics,” Proc. SPIE 3353, 300–309 (1998). [CrossRef]

] and the realization of 50W class SFG Na guide star lasers [21

21. C. A. Denman, P. D. Hillman, G. T. Moore, J. M. Telle, J. E. Preston, J. D. Drummond, and R. Q. Fugate, “Realization of a 50-watt facility-class sodium guidestar pump laser,” Proc. SPIE 5707, 46–49 (2005) [CrossRef]

].

Acknowledgments

This paper is based upon work supported by the National Science Foundation under Cooperative Agreement No. AST0084699. We thank B. Ellerbroeck and J. C. Shelton for useful discussions and R. F. Wuerker, B. Middlemiss and N. Wild for technical contributions.

References and links

1.

P. W. Milonni, “Resource letter: AOA-1: Adaptive optics for astronomy,” Am. J. Phys. 67, 476 (1999). [CrossRef]

2.

N. Ageorges and C. Dainty, Laser Guide Star Adaptive Optics for Astronomy (Kluwer Academic Publishers, 2000).

3.

N. Hubin, B. L. Ellerbroek, R. Arsenault, R. M. Clare, R. Dekany, L. Gilles, M. Kasper, G. Herriot, M. Le Louarn, E. Marchetti, S. Oberti, J. Stoesz, J. P. Veran, and C. Vérinaud, “Adaptive optics for Extremely Large Telescopes,” in Proceedings IAU Symposium No. 232, 60–85 (2005).

4.

R. Foy and A. Labeyrie, “Feasibility of adaptive telescope with laser probe,” Astron. Astrophys. 152, 29 (1985).

5.

Requirements from Gemini RFP no. N231397, Dec. 2003.

6.

C. E. Max, K. Avicola, J. M. Brase, H. W. Friedman, H. D. Bissinger, J. Duff, D. T. Gavel, J. A. Horton, R. Kiefer, J. R. Morris, S. S. Olivier, R. W. Presta, D. A. Rapp, J. T. Salmon, and K. E. Waltjen, “Design, layout, and early results of a feasibility experiment for sodium-layer laser-guide-star adaptive optics,” J. Opt. Soc. Am. A. 11, 813 (1994). [CrossRef]

7.

T. H. Jeys, A. A. Brailove, and A. Mooradian, “Sum frequency generation of sodium resonance radiation,” Appl. Opt. 28, 2588 (1989). [CrossRef] [PubMed]

8.

A. Tracy, A. Hankla, C. Lopez, D. Sadighi, N. Rogers, K. Groff, I. McKinnie, and C. d’Orgeville, “High-Power Solid-State Sodium Beacon Laser Guidestar for the Gemini North Observatory,” Proc. SPIE 5490, 998–1009 (2004). [CrossRef]

9.

D. M. Pennington, R. Beach, J. Dawson, A. Drobshoff, Z. Liao, S. Payne, D. Bonaccini, W. Hackenberg, and L. Taylor, “Compact fiber laser approach to generating 589 nm laser guide stars,” in Proceedings of Conference on Lasers and Electro-Optics Europe, 730 (2003).

10.

D. Bonaccini Calia, W. Hackenberg, C. Araujo, I. Guidolin, and J. L. Alvarez, “Laser guide star related activities at ESO,” Proc. SPIE 5490, 974–980 (2004). [CrossRef]

11.

E. J. Kibblewhite and F. Shi, “Design and field test of an 8 watt sum-frequency laser for adaptive optics,” Proc. SPIE 3353, 300–309 (1998). [CrossRef]

12.

Response to Gemini RFP no. N231397, Jan 2004.

13.

T. P. Rutten, P. J. Veitch, and J. Munch, “Development of a Sodium Laser Guide Star for Astronomical Adaptive Optics Systems,” presented at the Australasian Conference on Optics, Lasers and Spectroscopy, Rotorua, New Zealand, 5–9 Dec. 2005.

14.

A. J. Alcock, P. B. Corkum, and D. J. James, “A simple mode-locking technique for large-aperture TEA CO2 lasers,” Appl. Phys. Lett. 30, 148 (1977). [CrossRef]

15.

J. E. Murray and W. H. Lowdermilk, “ND:YAG regenerative amplifier,” J. Appl. Phys. 51, 3548 (1980). [CrossRef]

16.

Australian Patent PCT/AU2006/ 001852, Dec. 2006.

17.

T. J. Kane and R. L. Byer, “Monolithic, unidirectional single-mode Nd:YAG ring laser,” Opt. Lett. 10, 65 (1985). [CrossRef] [PubMed]

18.

J. C. Bienfang, C. A. Denman, B. W. Grime, P. D. Hillman, G. T. Moore, and J. M. Telle, “20 W of continuous-wave sodium D2 resonance radiation from sum-frequency generation with injection-locked lasers,” Opt. Lett. 28, 2219 (2003). [CrossRef] [PubMed]

19.

D. C. Hanna, C. G. Sawyers, and M. A. Yuratich, “Telescopic resonators for large-volume TEM00-mode operation,” Opt. Quantum Electron. 13, 493 (1981). [CrossRef]

20.

J. J. Degnan, “Theory of the Optimally Coupled Q-Switched Laser,” IEEE J. Quantum Electron. 25, 214 (1989). [CrossRef]

21.

C. A. Denman, P. D. Hillman, G. T. Moore, J. M. Telle, J. E. Preston, J. D. Drummond, and R. Q. Fugate, “Realization of a 50-watt facility-class sodium guidestar pump laser,” Proc. SPIE 5707, 46–49 (2005) [CrossRef]

OCIS Codes
(010.1080) Atmospheric and oceanic optics : Active or adaptive optics
(140.3580) Lasers and laser optics : Lasers, solid-state

ToC Category:
Lasers and Laser Optics

History
Original Manuscript: January 18, 2007
Revised Manuscript: February 19, 2007
Manuscript Accepted: February 22, 2007
Published: March 5, 2007

Citation
Thomas P. Rutten, Peter J. Veitch, Céline d'Orgeville, and Jesper Munch, "Injection mode-locked guide star laser concept and design verification experiments," Opt. Express 15, 2369-2374 (2007)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-15-5-2369


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. P. W. Milonni, "Resource letter: AOA-1: Adaptive optics for astronomy," Am. J. Phys. 67, 476 (1999). [CrossRef]
  2. N. Ageorges and C. Dainty, Laser Guide Star Adaptive Optics for Astronomy (Kluwer Academic Publishers, 2000).
  3. N. Hubin, B. L. Ellerbroek, R. Arsenault, R. M. Clare, R. Dekany, L. Gilles, M. Kasper, G. Herriot, M. Le Louarn, E. Marchetti, S. Oberti, J. Stoesz, J. P. Veran and C. Vérinaud, "Adaptive optics for Extremely Large Telescopes," in Proceedings IAU Symposium No. 232, 60-85 (2005).
  4. R. Foy and A. Labeyrie, "Feasibility of adaptive telescope with laser probe," Astron. Astrophys. 152, 29 (1985).
  5. Requirements from Gemini RFP no. N231397, Dec. 2003.
  6. C. E. Max, K. Avicola, J. M. Brase, H. W. Friedman, H. D. Bissinger, J. Duff, D. T. Gavel, J. A. Horton, R. Kiefer, J. R. Morris, S. S. Olivier, R. W. Presta, D. A. Rapp, J. T. Salmon and K. E. Waltjen, "Design, layout, and early results of a feasibility experiment for sodium-layer laser-guide-star adaptive optics," J. Opt. Soc. Am. A. 11, 813 (1994). [CrossRef]
  7. T. H. Jeys, A. A. Brailove and A. Mooradian, "Sum frequency generation of sodium resonance radiation," Appl. Opt. 28, 2588 (1989). [CrossRef] [PubMed]
  8. A. Tracy, A. Hankla, C. Lopez, D. Sadighi, N. Rogers, K. Groff, I. McKinnie and C. d'Orgeville, "High-Power Solid-State Sodium Beacon Laser Guidestar for the Gemini North Observatory," Proc. SPIE 5490, 998-1009 (2004). [CrossRef]
  9. D. M. Pennington, R. Beach, J. Dawson, A. Drobshoff, Z. Liao, S. Payne, D. Bonaccini, W. Hackenberg and L. Taylor, "Compact fiber laser approach to generating 589 nm laser guide stars," in Proceedings of Conference on Lasers and Electro-Optics Europe, 730 (2003).
  10. D. Bonaccini Calia, W. Hackenberg, C. Araujo, I. Guidolin and J. L. Alvarez, "Laser guide star related activities at ESO," Proc. SPIE 5490, 974-980 (2004). [CrossRef]
  11. E. J. Kibblewhite and F. Shi, "Design and field test of an 8 watt sum-frequency laser for adaptive optics," Proc. SPIE 3353, 300-309 (1998). [CrossRef]
  12. Response to Gemini RFP no. N231397, Jan 2004.
  13. T. P. Rutten, P. J. Veitch and J. Munch, "Development of a Sodium Laser Guide Star for Astronomical Adaptive Optics Systems," presented at the Australasian Conference on Optics, Lasers and Spectroscopy, Rotorua, New Zealand, 5-9 Dec. 2005.
  14. A. J. Alcock, P. B. Corkum and D. J. James, "A simple mode-locking technique for large-aperture TEA CO2 lasers," Appl. Phys. Lett. 30, 148 (1977). [CrossRef]
  15. J. E. Murray and W. H. Lowdermilk, "ND:YAG regenerative amplifier," J. Appl. Phys. 51, 3548 (1980). [CrossRef]
  16. Australian Patent PCT/AU2006/ 001852, Dec. 2006.
  17. T. J. Kane and R. L. Byer, "Monolithic, unidirectional single-mode Nd:YAG ring laser," Opt. Lett. 10, 65 (1985). [CrossRef] [PubMed]
  18. J. C. Bienfang, C. A. Denman, B. W. Grime, P. D. Hillman, G. T. Moore and J. M. Telle, "20 W of continuous-wave sodium D2 resonance radiation from sum-frequency generation with injection-locked lasers," Opt. Lett. 28, 2219 (2003). [CrossRef] [PubMed]
  19. D. C. Hanna, C. G. Sawyers and M. A. Yuratich, "Telescopic resonators for large-volume TEM00-mode operation," Opt. Quantum Electron. 13, 493 (1981). [CrossRef]
  20. J. J. Degnan, "Theory of the Optimally Coupled Q-Switched Laser," IEEE J. Quantum Electron. 25, 214 (1989). [CrossRef]
  21. C. A. Denman, P. D. Hillman, G. T. Moore, J. M. Telle, J. E. Preston, J. D. Drummond and R. Q. Fugate, "Realization of a 50-watt facility-class sodium guidestar pump laser," Proc. SPIE 5707,46-49 (2005) [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited