OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 16, Iss. 15 — Jul. 21, 2008
  • pp: 11027–11031
« Show journal navigation

CMOS-compatible dual-output silicon modulator for analog signal processing

S. J. Spector, M. W. Geis, G.-R. Zhou, M. E. Grein, F. Gan, M.A. Popović, J. U. Yoon, D. M. Lennon, E. P. Ippen, F. X. Kärtner, and T. M. Lyszczarz  »View Author Affiliations


Optics Express, Vol. 16, Issue 15, pp. 11027-11031 (2008)
http://dx.doi.org/10.1364/OE.16.011027


View Full Text Article

Acrobat PDF (199 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

A broadband, Mach-Zehnder-interferometer based silicon optical modulator is demonstrated, with an electrical bandwidth of 26 GHz and VπL of 4 V∙cm. The design of this modulator does not require epitaxial overgrowth and is therefore simpler to fabricate than previous devices with similar performance.

© 2008 Optical Society of America

1. Introduction

The development of silicon based photonics has the potential to allow monolithically-integrated, low-cost optical devices on a platform compatible with CMOS circuits [1

1. G. T. Reed and A. P. Knights, “Silicon Photonics: an Introduction,” (John Wiley, Chichester, 2004)

]. Optical modulators are an essential component in most applications, and there has been considerable recent effort directed at developing silicon based optical modulators [2

2. L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, “40 Gbit/s silicon optical modulator for highspeed applications,” Electron. Lett. , 43 (22) pp. 1196-1197 (2007). [CrossRef]

4

4. L. Liao, D. Samara-Rubio, M. Morse, A. Liu, and D. Hodge, “High speed silicon Mach-Zehnder modulator,” Opt. Express 13, 3129-3135 (2005). [CrossRef] [PubMed]

]. The most successful devices have used the free-carrier plasma dispersion effect [5

5. R. A. Soref and B. R. Bennett, “Electrooptical effects in silicon,” IEEE J. Quantum Electron. 23, 123-129 (1987). [CrossRef]

], where a change in density of carriers causes a change in the refractive index of silicon. This effect can be accessed by carrier injection in a p-i-n diode [3

3. Q. 'u, S. Manipatruni, B. Schmidt, J. Shakya, and M. Lipson, “12.5 Gbit/s carrier-injection-based silicon microring silicon modulators,” Opt. Express 15, 430-436 (2007).

], accumulation in a MOS capacitor [4

4. L. Liao, D. Samara-Rubio, M. Morse, A. Liu, and D. Hodge, “High speed silicon Mach-Zehnder modulator,” Opt. Express 13, 3129-3135 (2005). [CrossRef] [PubMed]

], or carrier depletion in a p-n diode [2

2. L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, “40 Gbit/s silicon optical modulator for highspeed applications,” Electron. Lett. , 43 (22) pp. 1196-1197 (2007). [CrossRef]

]. Carrier depletion has achieved the best high speed result to date, with a Mach Zehnder based modulator achieving 30 GHz of electrical bandwidth and a VπL of 4 V∙cm [2

2. L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, “40 Gbit/s silicon optical modulator for highspeed applications,” Electron. Lett. , 43 (22) pp. 1196-1197 (2007). [CrossRef]

]. One disadvantage of the design in [2

2. L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, “40 Gbit/s silicon optical modulator for highspeed applications,” Electron. Lett. , 43 (22) pp. 1196-1197 (2007). [CrossRef]

] is the use of a top contact which requires an epitaxial silicon overgrowth. A recent result used a design that eliminated the top contact, but did not achieve the same performance [6

6. D. Marris-Morini, L. Vivien, J. M. Fédéli, E. Cassan, P. Lyan, and S. Laval, “Low loss and high speed silicon optical modulator based on a lateral carrier depletion structure,” Opt. Express 16, 334-339 (2008). [CrossRef] [PubMed]

]. The design described here does not use a top contact, and shows performance approaching that of [2

2. L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, “40 Gbit/s silicon optical modulator for highspeed applications,” Electron. Lett. , 43 (22) pp. 1196-1197 (2007). [CrossRef]

]. The modulator demonstrated here achieves 26 GHz of electrical bandwidth and a VπL of 4 Vcm.

There are additional considerations for the design of a modulator which may depend on the application. For analog applications, a modulator with two complementary outputs can be used to linearize the transfer function of the modulator and compensate for fluctuations external to the modulator [7

7. J. C. Twichell and R. Helkey, “Phase-encoded optical sampling for analog-to-digital converters,” IEEE Photonic Technol. Lett. 12, 1237-1239 (2000). [CrossRef]

,8

8. F. X. Kärtner, R. Amatya, M. Araghchini, J. Birge, H. Byun, J. Chen, M. Dahlem, N. A. DiLello, F. Gan, C.W. Holzwarth, J. L. Hoyt, E. P. Ippen, A. Khilo, J. Kim, M. Kim, A. Motamedi, J. S. Orcutt, M. Park, M. Perrott, M. A. Popović, R. J. Ram, H. I. Smith, G. R. Zhou, S. J. Spector, T. M. Lyszczarz, M. W. Geis, D. M. Lennon, J. U. Yoon, M. E. Grein, and R. T. Schulein, “Photonic Analog-to-Digital Conversion with Electronic-Photonic Integrated Circuits,” Proceedings of SPIE Photonics West, (Invited Paper), San Jose, CA, USA, Jan. 2008.

], such as variations in the laser output. The design described here uses a balanced Mach-Zehnder interferometer with broadband 3 dB couplers. The input 3 dB coupler is a symmetric Y-junction, while the output 3 dB coupler uses an adiabatic 4- port structure to provide two complementary outputs.

2. Design

The modulators are fabricated using Unibond silicon-on-insulator (SOI) wafers with a 0.22 μm thick layer of silicon above a 3 μm buried oxide. Figure 1(a) schematically shows the top-view of the modulator. The active areas of the device are p-n diode phase shifter sections in the arms of the modulator. Modulators using reverse bias p-n junctions can be very fast; their electrical speed is usually only limited by capacitance. By employing a relatively short interaction length of 0.5 mm (the travel time of the light is only 5 ps), a simple lumped-element electrode design can be used to achieve speeds of about 30 GHz. The modulator can be operated in a push-pull configuration by driving the center electrode (as shown), or a single arm can be driven. An additional thermal phase shifter (not shown) is fabricated on one arm, to allow the relative optical phase of the two arms of the modulator to be adjusted independently of the diodes.

An adiabatic 4-port 3 dB coupler is used to interfere the two arms at the output of the Mach-Zehnder interferometer leading to two complementary modulator output ports. An adiabatic 3 dB coupler design [9

9. K. Solehmainen, M. Kapulainen, M. Harjanne, and T. Aalto, “Adiabatic and multimode interference couplers on silicon-on-insulator,” IEEE Photonic Technol. Lett. 18, 2287-2289 (2006). [CrossRef]

] was chosen over a conventional 3 dB coupler because the former has less stringent fabrication tolerances. Typically, adiabatic couplers have the disadvantage that they are fairly large – in the millimeters. This is not the case in strongly confined waveguides, however. Here an effort was made to optimize the design for short length, and the resulting design for the adiabatic coupler is only 130 μm long. Mode-profile converting tapers are also needed to provide efficient fiber-to-chip coupling at the input and outputs. For this purpose, a silicon inverse-taper mode converter combined with a lower index silicon oxynitride waveguide [10

10. T. Shoji, T. Tsuchizawa, T. Watanabe, K. Yamada, and H. Morita, “Spot-size converter for low-loss coupling between 0.3-μm-square Si wire waveguides and single-mode fibers,” EOS 2002. 2002 IEEE/LEOS Annual Meeting Conference Proceedings,1, pp. 289-290.

] was used.

Figure 1(b) shows schematically the cross-section of the waveguide in the active area of the modulator. The central region (core) of the waveguide is 220 nm thick, 500 nm wide, and lightly n-type doped to a concentration of 2×1017cm-3, resulting in a break down voltage of 16 V. The sidewalls are moderately doped, n-type on one side and p-type on the other, to a concentration of 1018 cm-3 and an approximate depth of 50 nm. When a reverse bias is applied, a depletion region forms at the p-n junction on one side of the waveguide. This depletion region’s lateral size increases into the center of the waveguide as the bias is increased, creating a change in the refractive index of the waveguide. To make electrical contact to the core of the waveguide, heavily doped, (1019 cm-3 concentration), 50 nm thick slab regions connect the waveguide to metal contacts located 1 μm away. To ensure good ohmic contact, the silicon slab under the metal contacts is degenerately doped to a concentration of 1021 cm-3. The parasitic resistance of the diodes including ohmic contacts and the resistance of the doped Si is usually <0.3 ω/cm.

Fig. 1. (a) Top-view layout of the dual-output modulator. (b) Schematic view of the crosssection of one of the phase shifters. (All dimensions are in μm).

3. Modeling

Simple modeling can be used to estimate the electrical bandwidth of a 0.5 mm long device. The input capacitance of the diodes in the Mach Zehnder interferometer is calculated to be ∼0.1 pF and the contact pad capacitance is < 0.05 pF. This gives an estimate total capacitance from 0.1 and 0.15 pF. The 5 ω of internal resistance in the Mach Zehnder and 50 ω output impedance of the RF power supply, gives a calculated RC bandwidth of between 20 and 30 GHz.

4. Results

The DC response of the modulator was tested by varying the DC bias voltage on arm #1 while the other arm remained at the same bias level. Figure 2 shows the simulated and measured normalized light intensity as a function of the applied voltage, for the two complementary outputs. The measured and simulated results are in good agreement with each other. To get a better measure of VπL, a longer device, with 5 mm arm lengths, was also measured. The output of that modulator (which was fabricated with only one output channel) is also shown in Fig. 2, and gives a VπL of just over 4 V∙cm. This is comparable to what had been achieved earlier with a structure requiring more complicated fabrication [2

2. L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, “40 Gbit/s silicon optical modulator for highspeed applications,” Electron. Lett. , 43 (22) pp. 1196-1197 (2007). [CrossRef]

]. Operating the modulator in a push-pull configuration has also been demonstrated, and cuts the effective VpL for the device in half to 2 V∙cm, as expected.

Fig. 2. Measured and simulated normalized light transmission as a function of applied voltage.

The high-frequency response of the modulator was measured by the following experimental setup: a 1550 nm laser beam is amplified and coupled into the modulator chip via a lensed fiber. The output beam from the modulator chip is collected by an aspheric lens, goes through a fiber amplifier and a 2 nm bandpass filter, and is finally detected with a ∼50 GHz InGaAs photodetector. A network analyzer is used to drive the modulator and to measure the signal on the photodetector. In order to distinguish the bandwidth limiting effects associated with cabling from the actual bandwidth performance of the device, the RF transmission response is first measured through the cables only. The cables were found to have a 3 dB bandwidth of 10 GHz. Then the fabricated modulator device is connected with the same cables to measure the total response. The net performance of the device is then obtained by subtracting the measured cable response from the total response. No attempt was made to impedance match the Mach Zehnder modulator to the 50-ω impedance of the RF source. Any losses from this impedance mismatch are not measured or compensated by this method.

Fig. 3. Measured frequency response of the modulator.

Figure 3 shows the small signal frequency response of the modulator after correction for frequency dependent cable losses. A 3-dB cut-off frequency of 26 GHz is reached in a 0.5 mm device, which agrees with the estimate calculated above. A shorter device with 0.25 mm long phase shifters was also measured, and exhibits between 30–40 GHz of bandwidth. In addition to the RC limitation mentioned above, the electrode can no longer be considered a lumped-element device at high frequencies. This leads to unpredictable behavior at higher frequencies, such as a secondary peak at 40 GHz in the 0.5 mm device. In order to drive the modulator with higher power, an RF amplifier and bias-T were added to the above experimental set-up. When running the 0.5 mm device in a push-pull configuration, 46 mW of RF power achieves ∼22% modulation depth, as defined by [11

11. P. W. Juodawlkis, J. C. Twichell, G. E. Betts, J. J. Hargreaves, R. D. Younger, J. L. Wasserman, F. J. O’Donnell, K. G. Ray, and R. C. Williamson, “Optically Sampled Analog-to-Digital Converters,” IEEE Trans. On Microwave Theory and Tech. 49, 1840-1853 (2001). [CrossRef]

], for a 26 GHz sinusoid. The RF power was measured by replacing the modulator with the network analyzer.

From the VπL of 2 V∙cm, it can be calculated that a voltage of ± 4.5 V is necessary to achieve a 22% modulation depth in a 0.5 mm device. This is roughly twice the voltage of a 46 mW signal into a 50 ω load. This difference can be explained by an enhancement of the drive voltage due to the impedence mismatch at the modulator. The modulator is expected to have high impedence, which causes most of the drive signal to be reflected. The combination of the reflected signal with the forward signal doubles the voltage at the modulator.

The optical loss of the device was estimated to be 5dB from the total fiber to fiber loss of 10 dB.

5. Discussion

The measured 22% modulation depth is small, but sufficient for some applications. In an optically sampled analog to digital converter, this modulation depth is sufficient to achieve a signal to noise ratio of 47 dB [11

11. P. W. Juodawlkis, J. C. Twichell, G. E. Betts, J. J. Hargreaves, R. D. Younger, J. L. Wasserman, F. J. O’Donnell, K. G. Ray, and R. C. Williamson, “Optically Sampled Analog-to-Digital Converters,” IEEE Trans. On Microwave Theory and Tech. 49, 1840-1853 (2001). [CrossRef]

]. This is only 6 dB less than the theoretical maximum of 53 dB achieved with a 50% modulation depth under otherwise similar conditions.

The modulation depth could also be improved by going to a traveling-wave electrode design. A traveling-wave electrode would allow devices to have longer lengths, and therefore lower Vπ, while still achieving high-speed operation. The results on the 0.25 mm device indicate that 40 GHz of bandwidth should be feasible in longer devices if a traveling-wave electrode is used. In addition, modeling has indicated that changing the doping type from n-type to p-type in the center of the waveguide can potentially increase the modulation efficiency by a factor of 2∼3, thereby reaching a VπL of 2 V∙cm.

6. Conclusion

We have demonstrated a silicon modulator with two complementary outputs, a VπL of 4 V∙cm (or 2 V∙cm for the whole device operating in push-pull), and a 3-dB bandwidth of 26 GHz. A modulation depth of 22% was achieved. The insertion loss of the device is 10 dB, about half of which occurs on chip, and half of which occurs coupling in and out of the device.

Acknowledgements

References and links

1.

G. T. Reed and A. P. Knights, “Silicon Photonics: an Introduction,” (John Wiley, Chichester, 2004)

2.

L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, “40 Gbit/s silicon optical modulator for highspeed applications,” Electron. Lett. , 43 (22) pp. 1196-1197 (2007). [CrossRef]

3.

Q. 'u, S. Manipatruni, B. Schmidt, J. Shakya, and M. Lipson, “12.5 Gbit/s carrier-injection-based silicon microring silicon modulators,” Opt. Express 15, 430-436 (2007).

4.

L. Liao, D. Samara-Rubio, M. Morse, A. Liu, and D. Hodge, “High speed silicon Mach-Zehnder modulator,” Opt. Express 13, 3129-3135 (2005). [CrossRef] [PubMed]

5.

R. A. Soref and B. R. Bennett, “Electrooptical effects in silicon,” IEEE J. Quantum Electron. 23, 123-129 (1987). [CrossRef]

6.

D. Marris-Morini, L. Vivien, J. M. Fédéli, E. Cassan, P. Lyan, and S. Laval, “Low loss and high speed silicon optical modulator based on a lateral carrier depletion structure,” Opt. Express 16, 334-339 (2008). [CrossRef] [PubMed]

7.

J. C. Twichell and R. Helkey, “Phase-encoded optical sampling for analog-to-digital converters,” IEEE Photonic Technol. Lett. 12, 1237-1239 (2000). [CrossRef]

8.

F. X. Kärtner, R. Amatya, M. Araghchini, J. Birge, H. Byun, J. Chen, M. Dahlem, N. A. DiLello, F. Gan, C.W. Holzwarth, J. L. Hoyt, E. P. Ippen, A. Khilo, J. Kim, M. Kim, A. Motamedi, J. S. Orcutt, M. Park, M. Perrott, M. A. Popović, R. J. Ram, H. I. Smith, G. R. Zhou, S. J. Spector, T. M. Lyszczarz, M. W. Geis, D. M. Lennon, J. U. Yoon, M. E. Grein, and R. T. Schulein, “Photonic Analog-to-Digital Conversion with Electronic-Photonic Integrated Circuits,” Proceedings of SPIE Photonics West, (Invited Paper), San Jose, CA, USA, Jan. 2008.

9.

K. Solehmainen, M. Kapulainen, M. Harjanne, and T. Aalto, “Adiabatic and multimode interference couplers on silicon-on-insulator,” IEEE Photonic Technol. Lett. 18, 2287-2289 (2006). [CrossRef]

10.

T. Shoji, T. Tsuchizawa, T. Watanabe, K. Yamada, and H. Morita, “Spot-size converter for low-loss coupling between 0.3-μm-square Si wire waveguides and single-mode fibers,” EOS 2002. 2002 IEEE/LEOS Annual Meeting Conference Proceedings,1, pp. 289-290.

11.

P. W. Juodawlkis, J. C. Twichell, G. E. Betts, J. J. Hargreaves, R. D. Younger, J. L. Wasserman, F. J. O’Donnell, K. G. Ray, and R. C. Williamson, “Optically Sampled Analog-to-Digital Converters,” IEEE Trans. On Microwave Theory and Tech. 49, 1840-1853 (2001). [CrossRef]

OCIS Codes
(130.3120) Integrated optics : Integrated optics devices
(230.2090) Optical devices : Electro-optical devices
(250.7360) Optoelectronics : Waveguide modulators

ToC Category:
Optoelectronics

History
Original Manuscript: April 3, 2008
Revised Manuscript: June 20, 2008
Manuscript Accepted: June 24, 2008
Published: July 9, 2008

Citation
S. J. Spector, M. W. Geis, G.-R. Zhou, M. E. Grein, F. Gan, M. A. Popovic, J. U. Yoon, D. M. Lennon, E. P. Ippen, F. Z. Kärtner, and T. M. Lyszczarz, "CMOS-compatible dual-output silicon modulator for analog signal processing," Opt. Express 16, 11027-11031 (2008)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-16-15-11027


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. G. T. Reed and A. P. Knights, Silicon Photonics: an Introduction (John Wiley, Chichester, 2004)
  2. L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, "40 Gbit/s silicon optical modulator for highspeed applications," Electron. Lett. 431196-1197 (2007). [CrossRef]
  3. Q. Xu, S. Manipatruni, B. Schmidt, J. Shakya, and M. Lipson, "12.5 Gbit/s carrier-injection-based silicon microring silicon modulators," Opt. Express 15, 430-436 (2007).
  4. L. Liao, D. Samara-Rubio, M. Morse, A. Liu, and D. Hodge, "High speed silicon Mach-Zehnder modulator," Opt. Express 13, 3129-3135 (2005). [CrossRef] [PubMed]
  5. R. A. Soref and B. R. Bennett, "Electrooptical effects in silicon," IEEE J. Quantum Electron. 23, 123-129 (1987). [CrossRef]
  6. D. Marris-Morini, L. Vivien, J. M. Fédéli, E. Cassan, P. Lyan, and S. Laval, "Low loss and high speed silicon optical modulator based on a lateral carrier depletion structure," Opt. Express 16, 334-339 (2008). [CrossRef] [PubMed]
  7. J. C. Twichell and R. Helkey, "Phase-encoded optical sampling for analog-to-digital converters," IEEE Photonic Technol. Lett. 12, 1237-1239 (2000). [CrossRef]
  8. F. X. Kärtner, R. Amatya, M. Araghchini, J. Birge, H. Byun, J. Chen, M. Dahlem, N. A. DiLello, F. Gan, C. W. Holzwarth, J. L. Hoyt, E. P. Ippen, A. Khilo, J. Kim, M. Kim, A. Motamedi, J. S. Orcutt, M. Park, M. Perrott, M. A. Popovi?, R. J. Ram, H. I. Smith, G. R. Zhou, S. J. Spector, T. M. Lyszczarz, M. W. Geis, D. M. Lennon, J. U. Yoon, M. E. Grein, and R. T. Schulein, "Photonic Analog-to-Digital Conversion with Electronic-Photonic Integrated Circuits," Proceedings of SPIE Photonics West, (Invited Paper), San Jose, CA, USA, Jan. 2008.
  9. K. Solehmainen, M. Kapulainen, M. Harjanne, and T. Aalto, "Adiabatic and multimode interference couplers on silicon-on-insulator," IEEE Photonic Technol. Lett. 18, 2287-2289 (2006). [CrossRef]
  10. T. Shoji, T. Tsuchizawa, T. Watanabe, K. Yamada, and H. Morita, "Spot-size converter for low-loss coupling between 0.3-μm-square Si wire waveguides and single-mode fibers," EOS 2002. 2002 IEEE/LEOS Annual Meeting Conference Proceedings, 1, pp. 289-290.
  11. P. W. Juodawlkis, J. C. Twichell, G. E. Betts, J. J. Hargreaves, R. D. Younger, J. L. Wasserman, F. J. O??Donnell, K. G. Ray, and R. C. Williamson, "Optically Sampled Analog-to-Digital Converters," IEEE Trans Microwave Theory Tech. 49, 1840-1853 (2001). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1. Fig. 2. Fig. 3.
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited