OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 16, Iss. 17 — Aug. 18, 2008
  • pp: 13133–13138
« Show journal navigation

Chip-to-chip optical interconnect using gold long-range surface plasmon polariton waveguides

Jin Tae Kim, Jung Jin Ju, Suntak Park, Min-su Kim, Seung Koo Park, and Myung-Hyun Lee  »View Author Affiliations


Optics Express, Vol. 16, Issue 17, pp. 13133-13138 (2008)
http://dx.doi.org/10.1364/OE.16.013133


View Full Text Article

Acrobat PDF (507 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We demonstrate a novel on-board chip-to-chip optical interconnect using long-range surface plasmon polariton (LR-SPP) waveguides that feature 2.5-cm-long gold strips embedded in a low loss polymer cladding. A TM-mode vertical-cavity surface-emitting laser (VCSEL) operating at a wavelength of 1.3 µm was butt-coupled into the waveguides in order to excite a fundamental LR-SPP mode and then the transmitted light was received with a photo-diode (PD). The waveguide width is varied in the range of 1.5–5.0 µm in order to optimize the insertion loss where the 3-µm-wide waveguide provides a minimum insertion loss of -17 dB, consisting of 6 dB/cm propagation loss and 2 dB coupling loss. An interconnect system based on the optimized waveguide with a 4-channel array is assembled with the arrayed optoelectronic chips. It shows the feasibility of 10 Gbps (2.5 Gbps×4 channels) signal transmission indicating that the LR-SPP waveguide is a potential transmission line for optical interconnection.

© 2008 Optical Society of America

1. Introduction

Since low loss lightwave guidance along a thin metal strip embedded in a dielectric material was explained theoretically by the long-range surface plasmon polariton (LR-SPP) [1

1. P. Berini, “Plasmon-polariton waves guided by thin lossy metal films of finite width: Bound modes of symmetric structures,” Phys. Rev. B 61, 10484–10503 (2000). [CrossRef]

], LR-SPP-based optical waveguides have attracted great attention in integrated optical devices and numerous optical components have been investigated [2–6

2. T. Nikolajsen, K. Leosson, I. Salakhutdinov, and S. I. Bozhevolnyi, “Polymer-based surface-plasmon-polariton stripe waeguides at telecommunication wavelengths,” Appl. Phys. Lett. 82, 668 (2003). [CrossRef]

].

Of these, polymer-based LR-SPP waveguides whose metal strips are embedded in low-loss polymer cladding material demonstrate that propagation loss can be reduced to 2.0 dB/cm and 1.4 dB/cm at the telecommunication wavelengths of 1.3 µm and 1.5 µm, respectively, and that light coupling efficiency with standard single-mode optical fiber can be reduced to 0.5 dB [7

7. J. T. Kim, S. Park, J. J. Ju, S. K. Park, M -s. Kim, and M -H. Lee, “Low-loss polymer-based long-range surface plasmon-polariton waveguide,” IEEE Photon. Technol. Lett. 19, 1374–1376 (2007). [CrossRef]

, 8

8. S. Park, M -s. Kim, J. T. Kim, S. K. Park, J. J. Ju, and M -H. Lee, “Long range surface plasmon polariton waveguides at 1.31 and 1.55 µm wavelengths,” Opt. Commun. 281, 2057–2061 (2008). [CrossRef]

]. In addition, pig-tailed polymer-based LR-SPP waveguides demonstrate their ability to transmit a high bit-rate optical signal of 40 Gbps [9

9. J. J. Ju, M -s. Kim, S. Park, J. T. Kim, S. K. Park, and M -H. Lee, “10 Gbps optical signal transmission via long-range surface plasmon polariton waveguide,” ETRI J. 29, 808–810 (2007). [CrossRef]

, 10

10. J. J. Ju, S. Park, M -s. Kim, J. T. Kim, S. K. Park, Y. J. Park, and M -H. Lee, “40 Gbit/s light signal transmission in long-range surface plasmon waveguides,” Appl. Phys. Lett. 91, 171117 (2007). [CrossRef]

]. Thus, the polymer-based LR-SPP waveguide is considered a new optical wave guiding medium, replacing the conventional dielectric optical waveguide in parallel chip-to-chip optical interconnects.

This research focuses on the practical implementation of LR-SPP waveguides in on-board chip-to-chip optical interconnect systems. To demonstrate short-distance optical data communication, an Au LR-SPP waveguide is directly butt-coupled with a vertical-cavity surface-emitting laser (VCSEL) and a photodiode (PD). In order to excite the fundamental LR-SPP mode, the light from the VCSEL is TM-polarized. The optical properties of the LR-SPP waveguide when it is coupled to optoelectronic devices are investigated at a wavelength of 1.3 µm. We have performed a 2.5 Gbps optical signal transmission experiment for four waveguide channels.

2. Fabrication and experiment

In order to implement an on-board chip-to-chip optical interconnect using an LR-SPP waveguide, a simple chip-to-chip optical interconnect system supporting 10 Gbps (2.5 Gbps×4 channels) was designed as shown in Fig. 1. It consists of an optical transmitter (Tx) module, a receiver (Rx) module, and a polymer-based LR-SPP waveguide. The Tx module comprises a driver IC and a VCSEL array chip. The receiver IC comprises a receiver IC and a photo-diode (PD) array chip.

Driver and receiver ICs from SiRES LABS were used for four channels of 2.5 Gbps signal processing. To ensure reliable and high-speed electrical interconnection of Tx/Rx modules, a differential-coupled micro-strip line with 100 ohm differential characteristic impedance is employed in the electric circuits.

Fig. 1. Architectural view of on-board chip-to-chip optical interconnect using polymer-based Au long-range surface plasmon polariton (LR-SPP) waveguide.
Fig. 2. Schematics of chip-to-chip optical interconnect transmission test set-up.

The operation principle is as follows. An electrical signal from a pulse pattern generator (PPG) is transmitted to the driver IC through the differential line. Then, the electrical signal from the driver IC is transmitted to the VCSEL. A TM-polarized beam (1.3 µm wavelength) from the VCSEL excites a fundamental LR-SPP wave, the SS0 b mode [1

1. P. Berini, “Plasmon-polariton waves guided by thin lossy metal films of finite width: Bound modes of symmetric structures,” Phys. Rev. B 61, 10484–10503 (2000). [CrossRef]

], via a direct end-fire coupling. Subsequently, the wave propagates along the metal strip, and then the beam reaches the PD array. The electrical signal from the PD is magnified by the receiver IC consisting of a TIA and a limiting amp. Finally, the electrical signal is investigated with a digital communication analyzer (DCA).

To investigate the optical properties of the Au LR-SPP waveguide when it is coupled to the TM-polarized VCSEL, a simple chip-to-chip optical transmission testing assembly consisting of a Tx/Rx module, a Tx/Rx test board, and an LR-SPP waveguide was prepared, as shown in Fig. 2. One end of the 2.5 cm-long LR-SPP waveguide array was aligned with the VCSEL’s aperture through direct butt-coupling without index matching liquid. Then the output face of the waveguide was imaged with a charge-coupled device (CCD). The captured mode profile was fitted with a Gaussian distribution to estimate the mode field diameter (MFD). After capturing the mode image, the transmitted powers were measured separately with an optical power meter through SMF to evaluate insertion loss. After maximum optical coupling was achieved with the SMF, the horizontal and vertical scanning of the VCSEL was carried out to estimate the 3 dB alignment tolerance. On the other hand, measurement of the PD’s 3 dB tolerance to the metal waveguide was not performed because the PD has a large enough receiving area of 50 µm (in diameter).

Figure 3 shows the MFDs and the insertion loss with the TM-polarized VCSEL as a function of metal strip width at the fixed Au thickness of 14.5 nm. Similar experimental results were observed; that is, the horizontal and vertical MFDs became broader as the metal width narrowed. Compared to the MFDs excited with 1.55 µm wavelength light [8

8. S. Park, M -s. Kim, J. T. Kim, S. K. Park, J. J. Ju, and M -H. Lee, “Long range surface plasmon polariton waveguides at 1.31 and 1.55 µm wavelengths,” Opt. Commun. 281, 2057–2061 (2008). [CrossRef]

], the MFDs measured with 1.3 µm light source showed a smaller value. As predicted by theory [1

1. P. Berini, “Plasmon-polariton waves guided by thin lossy metal films of finite width: Bound modes of symmetric structures,” Phys. Rev. B 61, 10484–10503 (2000). [CrossRef]

], the fundamental LR-SPP mode is more tightly confined at shorter wavelengths for a given metal geometry, resulting in a narrower MFD and higher absorption.

Fig. 3. Mode field diameter and insertion loss as functions of metal strip width. Values are measured at 1.3 µm wavelength.

Figure 4 shows horizontal and vertical 3 dB alignment tolerances of the Au LR-SPP waveguide with the TM-polarized VCSEL in relation to the metal strip width. From the optical power variation measured under horizontal and vertical VCSEL scanning, a coupling tolerance of 3 dB was estimated. As expected from the MFD measurement, the estimated values increase as the metal width narrows. In particular, the horizontal 3 dB coupling tolerances are slightly larger compared to those of the vertical direction, and the difference between them increases as the metal strip width narrows. The largest horizontal and vertical 3 dB alignment tolerances were measured to be ±7 µm and ±5.2 µm, respectively, for the strip width of 1.5 µm.

Fig. 4. Horizontal and vertical 3 dB alignment tolerances of the Au LR-SPP with the TM-polarized VCSEL in relation to the metal strip width.
Fig. 5. (a). Assembled chip-to-chip optical interconnect system using the Au LR-SPP waveguide (the inset shows the coupling between the TM-polarized VCSEL and the Au LR-SPP waveguide), and (b) measured optical eye diagram for one channel (2.5 Gbps data rate) of the four receiver channels.

Although the lower propagation loss of the narrower metal strip width is advantageous for chip-to-chip optical interconnects, the higher coupling loss between the TM-polarized VCSEL and the Au LR-SPP waveguide is disadvantageous. Thus, we have to optimize the trade-off between propagation loss and coupling loss when the Au LR-SPP waveguide is used for chip-to-chip optical interconnects. Considering the insertion loss and a power budget of 20 dB, a 3 µm wide LR-SPP waveguide was chosen for our practical chip-to-chip optical signal transmission experiment.

To implement the chip-to-chip optical interconnect experiment, one end of the Au LR-SPP waveguide array was aligned into the VCSEL’s aperture, and a current indicator in the receiver IC was used to monitor the degree of alignment between the waveguide output and the PD. The average insertion loss was -17 dB, which is the sum of 6 dB/cm times 2.5 (the waveguide length in cm unit) for the propagation loss and 2 dB for the coupling loss. Since index matching liquid was not used between the metal waveguide and the optoelectronic devices, the insertion loss can be reduced if the liquid is used.

Figure 5(a) shows the assembled chip-to-chip optical interconnect test system installed with the polymer-based Au LR-SPP waveguide, and Fig. 5(b) shows the measured eye diagram for one channel of the receiver module. A 2.5 Gbps non-return-to-zero pseudorandom bit sequence (223-1) of the optical signals was transmitted through the metal waveguide. The eye diagram for one optimized channel was clearly open at room temperature. The peak-to-peak timing jitter was 132 ps, and the rise and fall times for the received waveform were 250 ps and 300 ps, respectively. The bit error rate (BER) obtained under the best condition was estimated to 10-10.

For better BER and error-free transmission of optical signal, the optical power reaching the PD should be increased. This requirement can be achieved by minimizing the insertion loss of the polymer-based Au LR-SPP waveguide. Using low-loss polymer materials having a low refractive index and absorption loss at a telecom wavelength can improve the optical properties of the LR-SPP waveguide [7

7. J. T. Kim, S. Park, J. J. Ju, S. K. Park, M -s. Kim, and M -H. Lee, “Low-loss polymer-based long-range surface plasmon-polariton waveguide,” IEEE Photon. Technol. Lett. 19, 1374–1376 (2007). [CrossRef]

]. Substitution of Au by Ag is an another suggestion to reduce the propagation loss of the LR-SPP waveguides since Ag has lower mode propagation attenuation (MPA) than that of Au [11

11. P. Berini, “Long-range surface plasmon-polariton waveguides in silica,” J. Appl. Phys. 102, 053105 (2007). [CrossRef]

].

On the other hand, the eye diagram in Fig. 5(b) shows the influence of all components because the pseudo random electrical bits pass through a long pathway, including the SMA connector, the Tx test board, the connector between board and module, the Tx module consisting of the VCSEL driver IC and the VCSEL, the Au LR-SPP waveguide, and reversed path components from the PD to SMA connectors. Therefore, the BER could be improved by simplifying the electric signal pathway.

3. Conclusion

To configure an on-board chip-to-chip optical interconnect using an Au LR-SPP waveguide, a polymer-based Au LR-SPP waveguide was developed and its optical characteristics with optoelectronic devices, including a TM-polarized VCSEL and a PD were investigated. With a simple Tx/Rx module supporting direct end-fire coupling between the Au LR-SPP waveguide and the optoelectronic chips, 10 Gbps (four channels of 2.5Gbps) data transmission was successfully accomplished at a wavelength of 1.3 µm. These results show that the polymer-based Au LR-SPP optical waveguide is a potential transmission line for very short-range direct chip-to-chip optical interconnects.

Acknowledgments

The authors would like to express their gratitude to Professor Sang-Yung Shin of KAIST for valuable discussions. This work was supported by the IT R&D program [2006-S-073-02] of the MKE/IITA, Korea.

References and links

1.

P. Berini, “Plasmon-polariton waves guided by thin lossy metal films of finite width: Bound modes of symmetric structures,” Phys. Rev. B 61, 10484–10503 (2000). [CrossRef]

2.

T. Nikolajsen, K. Leosson, I. Salakhutdinov, and S. I. Bozhevolnyi, “Polymer-based surface-plasmon-polariton stripe waeguides at telecommunication wavelengths,” Appl. Phys. Lett. 82, 668 (2003). [CrossRef]

3.

R. Charbonneau, C. Scales, I. Breukelaar, S. Fafard, N. Lahoud, G. Mattiussi, and P. Berini, “Passive integrated optics elements based on long-range surface plasmon polaritons,” J. Lightw. Technol. 24, 477–494 (2006). [CrossRef]

4.

A. Boltasseva and S. I. Bozhevolnyi, “Directional couplers using long-range surface plasmon polarition waveguides,” IEEE. J. Sel. Topic. Quantum. Electron. 12, 1233–1241 (2006). [CrossRef]

5.

T. Nikolajsen, K. Leosson, and S. I. Bozhevolnyi, “Surface plasmon polariton based modulators and switches operating at telecom wavelengths,” Appl. Phys. Lett. 88, 5833–5835 (2004). [CrossRef]

6.

S. Jetté-Charbonneau and P. Berini, “External cavity laser using a long-range surface plasmon grating as a distributed Bragg reflector,” Appl. Phys. Lett. 91, 181114 (2007). [CrossRef]

7.

J. T. Kim, S. Park, J. J. Ju, S. K. Park, M -s. Kim, and M -H. Lee, “Low-loss polymer-based long-range surface plasmon-polariton waveguide,” IEEE Photon. Technol. Lett. 19, 1374–1376 (2007). [CrossRef]

8.

S. Park, M -s. Kim, J. T. Kim, S. K. Park, J. J. Ju, and M -H. Lee, “Long range surface plasmon polariton waveguides at 1.31 and 1.55 µm wavelengths,” Opt. Commun. 281, 2057–2061 (2008). [CrossRef]

9.

J. J. Ju, M -s. Kim, S. Park, J. T. Kim, S. K. Park, and M -H. Lee, “10 Gbps optical signal transmission via long-range surface plasmon polariton waveguide,” ETRI J. 29, 808–810 (2007). [CrossRef]

10.

J. J. Ju, S. Park, M -s. Kim, J. T. Kim, S. K. Park, Y. J. Park, and M -H. Lee, “40 Gbit/s light signal transmission in long-range surface plasmon waveguides,” Appl. Phys. Lett. 91, 171117 (2007). [CrossRef]

11.

P. Berini, “Long-range surface plasmon-polariton waveguides in silica,” J. Appl. Phys. 102, 053105 (2007). [CrossRef]

OCIS Codes
(130.3120) Integrated optics : Integrated optics devices
(200.4650) Optics in computing : Optical interconnects
(240.6680) Optics at surfaces : Surface plasmons

ToC Category:
Optics in computing

History
Original Manuscript: May 28, 2008
Revised Manuscript: August 1, 2008
Manuscript Accepted: August 6, 2008
Published: August 12, 2008

Citation
Jin Tae Kim, Jung Jin Ju, Suntak Park, Min-su Kim, Seung Koo Park, and Myung-Hyun Lee, "Chip-to-chip optical interconnect using gold long-range surface plasmon polariton waveguides," Opt. Express 16, 13133-13138 (2008)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-16-17-13133


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. P. Berini, "Plasmon-polariton waves guided by thin lossy metal films of finite width: Bound modes of symmetric structures," Phys. Rev. B 61, 10484-10503 (2000). [CrossRef]
  2. T. Nikolajsen, K. Leosson, I. Salakhutdinov, and S. I. Bozhevolnyi, "Polymer-based surface-plasmon-polariton stripe waeguides at telecommunication wavelengths," Appl. Phys. Lett. 82, 668 (2003). [CrossRef]
  3. R. Charbonneau, C. Scales, I. Breukelaar, S. Fafard, N. Lahoud, G. Mattiussi, P. Berini, "Passive integrated optics elements based on long-range surface plasmon polaritons," J. Lightwave Technol. 24, 477-494 (2006). [CrossRef]
  4. A. Boltasseva and S. I. Bozhevolnyi, "Directional couplers using long-range surface plasmon polarition waveguides," IEEE.J. Sel. Top. Quantum Electron 12, 1233-1241 (2006). [CrossRef]
  5. T. Nikolajsen, K. Leosson, and S. I. Bozhevolnyi, "Surface plasmon polariton based modulators and switches operating at telecom wavelengths," Appl. Phys. Lett. 88, 5833-5835 (2004). [CrossRef]
  6. S. Jetté-Charbonneau, P. Berini, "External cavity laser using a long-range surface plasmon grating as a distributed Bragg reflector," Appl. Phys. Lett. 91, 181114 (2007). [CrossRef]
  7. J. T. Kim, S. Park, J. J. Ju, S. K. Park, M -s. Kim, and M -H. Lee, "Low-loss polymer-based long-range surface plasmon-polariton waveguide," IEEE Photon. Technol. Lett. 19, 1374-1376 (2007). [CrossRef]
  8. S. Park, M -s. Kim, J. T. Kim, S. K. Park, J. J. Ju, and M -H. Lee, "Long range surface plasmon polariton waveguides at 1.31 and 1.55 μm wavelengths," Opt. Commun. 281, 2057-2061 (2008). [CrossRef]
  9. J. J. Ju, M -s. Kim, S. Park, J. T. Kim, S. K. Park, and M -H. Lee, "10 Gbps optical signal transmission via long-range surface plasmon polariton waveguide," ETRI J. 29, 808-810 (2007). [CrossRef]
  10. J. J. Ju, S. Park, M -s. Kim, J. T. Kim, S. K. Park, Y. J. Park, and M -H. Lee, "40 Gbit/s light signal transmission in long-range surface plasmon waveguides," Appl. Phys. Lett. 91, 171117 (2007). [CrossRef]
  11. P. Berini, "Long-range surface plasmon-polariton waveguides in silica," J. Appl. Phys. 102, 053105 (2007). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited