OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 17, Iss. 1 — Jan. 5, 2009
  • pp: 185–192
« Show journal navigation

Plasmon-enhanced emission from optically-doped MOS light sources

Aaron C. Hryciw, Young Chul Jun, and Mark L. Brongersma  »View Author Affiliations


Optics Express, Vol. 17, Issue 1, pp. 185-192 (2009)
http://dx.doi.org/10.1364/OE.17.000185


View Full Text Article

Acrobat PDF (486 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We evaluate the spontaneous emission rate (Purcell) enhancement for optically-doped metal–dielectric–semiconductor light-emitting structures by considering the behavior of a semiclassical oscillating point dipole placed within the dielectric layer. For a Ag–SiO2–Si structure containing emitters at the center of a 20-nm-thick SiO2 layer, spontaneous emission rate enhancements of 40 to 60 can be reached in the wavelength range of 600 to 1800 nm, far away from the surface plasmon resonance; similar enhancements are also possible if Al is used instead of Ag. For dipoles contained in the thin oxide layer of a Ag–SiO2–Si–SiO2 structure, the emission exhibits strong preferential coupling to a single well-defined Si waveguide mode. This work suggests a means of designing a new class of power-efficient, high-modulation-speed, CMOS-compatible optical sources that take full advantage of the excellent electrical properties and plasmon-enhanced optical properties afforded by MOS devices.

© 2009 Optical Society of America

1. Introduction

As a key building-block of the integrated electronics industry, the metal–oxide–semiconductor (MOS) structure is fabricated using mature Si processing technology and has been studied exhaustively with respect to its electrical properties. In stark contrast, its optical properties have largely been ignored, as the top metal gate is generally considered too reflective or absorbing for optical applications. Interestingly, it is well documented that an increase in the spontaneous emission decay rate of dipolar emitters, such as fluorescent molecules or quantum dots, can be attained by placing them near metal surfaces [6

6. G. W. Ford and W. H. Weber, “Electromagnetic interactions of molecules with metal surfaces,” Phys. Rep. 113, 195–287 (1984). [CrossRef]

]. When close to the metal surface, new decay pathways open up for the emitter, including decay into surface plasmon-polariton (SPP) modes. SPPs are electron density waves propagating along metal–dielectric interfaces which exhibit a strong coupling to electromagnetic fields (“light”). In conventional solid-state lighting devices, the excitation of SPPs is suppressed as much as possible: the SPP energy is typically dissipated in the metal, lowering device efficiency.

Recently, several attempts have been made to recover the energy coupled to SPPs by using nanostructured metals in light-emitting devices. This can increase the out-coupling efficiency, decrease the radiative lifetime of emitters, and modify the angular distribution of the emission [7

7. W. L. Barnes, “Electromagnetic crystals for surface plasmon polaritons and the extraction of light from emissive devices,” J. Lightwave Tech. 17, 2170–2182 (1999). [CrossRef]

, 8

8. J. Vučković, M. Loncar, and A. Scherer, “Surface plasmon enhanced light-emitting diode,” IEEE J. Quantum Electron. 36, 1131–1144 (2000). [CrossRef]

, 9

9. J. S. Q. Liu and M. Brongersma, “Omnidirectional light emission via surface plasmon polaritons,” Appl. Phys. Lett. 90, 091116 (2007). [CrossRef]

]. Particularly pronounced changes in decay rates were recently predicted for metal–dielectric–metal (MDM) waveguides that support highly confined SPP modes [10

10. Y. C. Jun, R. D. Kekatpure, J. S. White, and M. Brongersma, “Nonresonant enhancement of spontaneous emission in metal-dielectric-metal plasmon waveguide structures,” Phys. Rev. B 78, 153111 (2008). [CrossRef]

]. The high dielectric contrast between the different layers in MOS structures also gives rise to highly-confined transverse magnetic (TM) modes; this is a direct consequence of the required continuity of the normal component of the dielectric displacement, D n = εE n, at any interface. Large increases in the decay rate of emitters embedded in the low-index oxide can thus be expected in these structures as well. The possibility to realize optically-doped MOS sources on Si may have tremendous potential based on ease of fabrication. Furthermore, efficient coupling to Si waveguides is straightforward if such sources are realized using silicon-on-insulator (SOI) technology. A schematic of a simple, on-chip light source applying this principle is shown in Fig. 1. This figure clearly shows the enhanced fields inside the oxide for a single supported TM mode and illustrates the possibility of coupling to a SOI waveguide. Although light sources based on MOS structures containing erbium [11

11. S. Wang, A. Eckau, E. Neufeld, R. Carius, and C. Buchal, “Hot electron impact excitation cross-section of Er3+ and electroluminescence from erbium-implanted silicon metal-oxide-semiconductor tunnel diodes,” Appl. Phys. Lett. 71, 2824–2826 (1997). [CrossRef]

, 12

12. K. Sun, W. J. Xu, B. Zhang, L. P. You, G. Z. Ran, and G. G. Qin, “Strong enhancement of Er3+ 1.54 μm electroluminescence through amorphous Si nanoparticles,” Nanotechnology 19, 105,708 (2008).

] or Si nanocrystals [13

13. A. Irrera, D. Pacifici, M. Miritello, G. Franzò, F. Priolo, F. Iacona, D. Sanfillipo, G. Di Stefano, and P. G. Fallica, “Electroluminescence properties of light emitting devices based on silicon nanocrystals,” Physica E 16, 395–399 (2003). [CrossRef]

] in the oxide layer have been demonstrated, the reports have focused on the electrical behavior of the devices; to the authors’ knowledge, evaluating metal–dielectric–semiconductor (MDS) light-emitting structures for decay rate enhancement has not yet been considered. The design of a device such as shown in Fig. 1 would involve analysis of the spontaneous emission rate enhancement, mode-coupling efficiencies, and charge-carrier injection; in this paper, we focus only on the first of these aspects.

Fig. 1. Schematic of a prototype CMOS-compatible light-emitting device architecture exploiting plasmonic decay rate enhancement of emitters in a planar metal–dielectric–semiconductor–dielectric (MDSD) structure and the possibility of coupling the emission into a SOI waveguide. Typical electric field profiles for supported transverse magnetic (TM) modes are shown in red.

2. Model

The most general planar geometry we consider is that of a point dipole in a dielectric slab of thickness LD and real dielectric constant εD, sandwiched between upper and lower claddings consisting of multilayer stacks. For a dipole with internal quantum efficiency η and decay rate γ free in an infinite dielectric, the normalized decay rate in the layered structure may be written as [6

6. G. W. Ford and W. H. Weber, “Electromagnetic interactions of molecules with metal surfaces,” Phys. Rep. 113, 195–287 (1984). [CrossRef]

]

γ̂γγfree=1η+η01freeddkdk.
(1)

When a dipole is oriented at an angle θ from the normal to the interfaces, the integrand in Eq. (1) is given by

1freeddk=321kD3e{kqD[cos2θ(k2r̃P)+12sin2θ(kD2r̃S+qD2r̃P)]}
(2)

where

r̃P=[1+rDPexp(2iqDd)][1+rD+Pexp(2iqDd+)]1rDPrD+Pexp(2iqDLD)
(3a)
r̃S=[1+rDSexp(2iqDd)][1+rD+Sexp(2iqDd+)]1rDSrD+Sexp(2iqDLD)
(3b)
r̃P=[1rDPexp(2iqDd)][1rD+Pexp(2iqDd+)]1rDPrD+Pexp(2iqDLD)
(3c)

take into account the multiple reflections at the dielectric slab’s surfaces, kD = 2πε D 1/2 / λ 0 is the magnitude of the wavevector in the dielectric, k is the in-plane wavevector (propagation constant of the mode), and q D = (k D 2 - k 2 )1/2 is the perpendicular (out-of-plane) wavevector. In Eqns. (3), r D+ P,S and r D- P,S are the effective P- and S-polarized (TM and TE) reflectivities at the upper and lower dielectric interfaces, respectively. For a dielectric layer clad with semi-infinite layers, r D+ P,S and r D- P,S reduce to the usual Fresnel reflectivities for single planar interfaces; for multilayer claddings, r D+ P,S and r D- P,S may be calculated using the transfer matrix approach [14

14. P. Yeh, Optical waves in layered media, 2nd ed. (Wiley-Interscience, New York, 2005).

].

We start by considering an emitter in the center of a dielectric (D) film (d +=d -= L D/2) clad by semi-infinite metal (M) and semiconductor (S) layers with (complex) dielectric constants ε M and ε S, respectively. Initially, we assume that the dipole is oriented perpendicular to the layer interfaces (θ = 0) and has unit quantum efficiency. This dipole couples most strongly to SPPs, which exhibit an electric field distribution that is dominantly perpendicular to the metal surface. While a complete account of the reflection of light from the D–M and D–S boundaries would include nonlocal effects via dielectric constants exhibiting both temporal and spatial dispersion, that is, ε = ε(ω, k), the layers are reasonably well described as local media with ε = ε(ω) so long as the dipole–interface distances are larger than ~ 10 nm [6

6. G. W. Ford and W. H. Weber, “Electromagnetic interactions of molecules with metal surfaces,” Phys. Rep. 113, 195–287 (1984). [CrossRef]

]. As such, we simulate a dipole in the center of a 20-nm-thick dielectric layer and use tabulated values for ε M (Ag) [15

15. A. D. Rakić, A. B. Djurišić, J. M. Elazar, and M. L. Majewski, “Optical properties of metallic films for vertical-cavity optoelectronic devices,” Appl. Opt. 37, 5271–2383 (1998). [CrossRef]

] and ε S (Si) [16

16. D. R. Lide, ed., CRC Handbook of Chemistry and Physics, Internet Version 2008, 88th ed. (Taylor & Francis, Boca Raton, FL, 2008).

]; for simplicity, we choose a dispersionless dielectric with ε D = 2.25, approximating that of SiO2. With its low loss in the visible, Ag serves as an exemplar for this discussion; CMOS-compatible metals such as Al exhibit qualitatively very similar behavior, as discussed later in the text.

3. Results and discussion

Calculated using Eq. (2), the normalized decay rate density for the semi-infinite Ag–SiO2–Si structure discussed above is shown in Fig. 2. The peaks in the decay rate density at each energy trace out the dispersion of the TM magnetic mode that provides the dominant decay pathway (red curve). Approaching Fig. 2 heuristically, the basic physics of the MDS structure becomes apparent. First, the red dispersion curve lies above the Si light line for the entire energy range being considered, in contrast to the bound SPP modes found at a single Ag–Si interface [10

10. Y. C. Jun, R. D. Kekatpure, J. S. White, and M. Brongersma, “Nonresonant enhancement of spontaneous emission in metal-dielectric-metal plasmon waveguide structures,” Phys. Rev. B 78, 153111 (2008). [CrossRef]

]. As such, the field profiles correspond to leaky SPP modes, marked by exponentially-growing solutions in the Si substrate; such solutions are physical insofar as they may be regarded as spatial transients, meaningful only for a finite distance in the Si [17

17. J. J. Burke, G. I. Stegeman, and T. Tamir, “Surface-polariton-like waves guided by thin, lossy metal films,” Phys. Rev. B 33, 5186–5201 (1986). [CrossRef]

]. While the interpretation of field distributions for leaky modes is thus complicated slightly, the limiting behavior of the dispersion relation remains intuitive. For energies near the Ag–SiO2 surface plasmon energy (h̅ω sp), the field becomes more concentrated in the dielectric layer than at low energies (see insets): the MDS dispersion relation’s asymptotic approach to this value mimics that of the single-interface DM case [6

6. G. W. Ford and W. H. Weber, “Electromagnetic interactions of molecules with metal surfaces,” Phys. Rep. 113, 195–287 (1984). [CrossRef]

]. At low energies, however, the MDS dispersion relation approaches the Si light line, since, relative to the high-energy case, the field is drawn out of the oxide layer in favor of the Si substrate.

Fig. 2. Normalized decay rate density for a perpendicular dipole located at the center of the 20-nm-thick dielectric layer in a Ag–SiO2–Si MDS structure. E-field profiles, normalized to unit H-field magnitude at the M–D interface, are shown in the insets.

The leaky nature of these modes is also highlighted by the difference in the peak width of the normalized decay rate density curves for the MDS and MDM structures, as illustrated in Fig. 3a for an emitter with λ 0 = 1535 nm. Whereas the MDM case supports a single bound gap-plasmon mode with a relatively well-defined propagation constant [10

10. Y. C. Jun, R. D. Kekatpure, J. S. White, and M. Brongersma, “Nonresonant enhancement of spontaneous emission in metal-dielectric-metal plasmon waveguide structures,” Phys. Rev. B 78, 153111 (2008). [CrossRef]

], the availability of leaky modes in the MDS case broadens its peak considerably. The sharp drop in decay rate density for the MDS plot at the maximum allowable k Si indicates the lack of de-excitation pathways with higher in-plane wavevectors. Decay into such high-k channels (lossy surface waves) [6

6. G. W. Ford and W. H. Weber, “Electromagnetic interactions of molecules with metal surfaces,” Phys. Rep. 113, 195–287 (1984). [CrossRef]

], is a purely absorptive loss mechanism, arising from the imaginary part of ε M.

Although the focus of this paper is on the semi-infinite MDS structure, emission into leaky SPP modes is not useful from the standpoint of on-chip light sources for integrated photonics. We have therefore also included in Fig. 3b the normalized decay rate density for a more viable device architecture (also see Fig. 1). This device structure could be fabricated on SOI, provided that the buried oxide (BOX) layer is sufficiently thick to limit leakage into the Si substrate [18

18. G. T. Reed and A. P. Knights, Silicon photonics: an introduction (John Wiley and Sons, Ltd., Chichester, England, 2004). [CrossRef]

]; in such a case, we may approximate the BOX layer by the infinite dielectric shown in Fig. 3b. In addition to an abrupt shoulder at k SiO2 marking the cutoff for SiO2 radiation modes, the MDSD case exhibits a similar low loss to LSW as in the MDS structure, with a peak of comparable sharpness to the MDM gap-plasmon mode, albeit at lower k ; this peak corresponds to a mode with the E-field distribution shown on the left side of Fig. 1, and has a propagation of length at 1535 nm of ~20 μ for this geometry.

Fig. 3. Decay rate density vs. k at λ 0 = 1535 nm and simulation geometries for (a) the semi-infinite MDS and MDM structures, and (b) the MDSD structure; in both cases, the dipole is situated at the center of the dielectric layer. The inset to (b) illustrates the effect of dipole position on the relative contributions of the surface plasmon polariton (SPP), lossy surface wave (LSW), and far-field radiation (rad.) pathways to the overall decay rate in the MDSD structure.

By integrating over the peak and comparing to the total power emitted by the dipole, we find that roughly 82% is coupled into this mode for a dipole at the center of the dielectric layer. In the inset to Fig. 3b, the efficacy of this coupling as a function of dipole position is illustrated: dipoles closer to the metal couple predominantly to LSWs, with more power being emitted into the MDSD SPP mode as the dipole approaches the Si surface. However, it is important to bear in mind that using a local dielectric constant causes an underestimation of the coupling to LSWs for very small dipole–metal distances (d + < 10 nm) [6

6. G. W. Ford and W. H. Weber, “Electromagnetic interactions of molecules with metal surfaces,” Phys. Rep. 113, 195–287 (1984). [CrossRef]

], such that the effect of quenching is likely to be stronger in this regime than predicted in the inset. This demonstrates the importance of careful control over the location of emitters during the fabrication of devices based on this principle. With this caveat, these results suggest that—given judicious emitter placement—one may indeed exploit this structure simultaneously to increase the decay rate of emitters and to couple their emission efficiently into a well-defined, specific guided-mode channel. The significant overlap of this mode with the SOI waveguide mode shown on the right of Fig. 1 can be used to ensure efficient coupling to a single low-loss dielectric waveguide mode and enable a very power-efficient source. For instance, if the MDSD structure shown in Fig. 3b is abruptly coupled to the equivalent SOI waveguide (i.e., the same structure with the metal and oxide layers removed, as on the right side of Fig. 1), the power transmittance between lowest-order TM modes is ~85% at 850 nm, considering the propagation constant mismatch and mode overlap, and neglecting scattering into radiation modes.

Returning to the semi-infinite cases, we plot in Fig. 4a a comparison of the overall decay rate enhancement, γ̂, with respect to a dipole in an infinite dielectric, for the MDS, MDM, and DM structures. Although this enhancement is strongest at the Ag–SiO2 surface plasmon resonance (λ 0 ~ 370 nm), the MDS case exhibits a strong non-resonant enhancement of ~40–60 between 600 and 1800 nm—only a factor of 2–3 smaller than that of the MDM structure; this behavior is nearly absent in the single-interface (DM) configuration. In particular, the enhancement at 1.5 μm is ~60, suggesting that this effect could be particularly useful for Er3+, which emits at this important telecommunications wavelength. It is important to note, however, that the enhancement decreases strongly with increased dielectric layer thickness [10

10. Y. C. Jun, R. D. Kekatpure, J. S. White, and M. Brongersma, “Nonresonant enhancement of spontaneous emission in metal-dielectric-metal plasmon waveguide structures,” Phys. Rev. B 78, 153111 (2008). [CrossRef]

], limiting the benefit of this effect in thicker Er-containing MOS structures such as those reported in [11

11. S. Wang, A. Eckau, E. Neufeld, R. Carius, and C. Buchal, “Hot electron impact excitation cross-section of Er3+ and electroluminescence from erbium-implanted silicon metal-oxide-semiconductor tunnel diodes,” Appl. Phys. Lett. 71, 2824–2826 (1997). [CrossRef]

] and [12

12. K. Sun, W. J. Xu, B. Zhang, L. P. You, G. Z. Ran, and G. G. Qin, “Strong enhancement of Er3+ 1.54 μm electroluminescence through amorphous Si nanoparticles,” Nanotechnology 19, 105,708 (2008).

].

Fig. 4. (a) Decay rate enhancements for DM, MDS, and MDM structures; for these three cases, the dipole is 10 nm from the metal surface. Two plots for the MDSD case of Fig. 3b are included for comparison: (red dashed line) perpendicular dipole at the center of the dielectric (d + = 10 nm); (black dashed line) emitters uniformly distributed such that d + ∊ [1.5,18.5] nm in the dielectric layer, averaged over all dipole orientations. Insets: E-field profiles for λ 0 = 850 nm. (b) The effect of internal quantum efficiency (η) on the decay rate enhancement for the MDSD structure shown in the inset (perpendicular dipole, d + = 10 nm).

The behavior of the finite MDSD case (schematized in the inset to Fig. 3b) is also included in Fig. 4a for comparison with the three semi-infinite cases. The red dashed line is for the situation which most closely resembles the corresponding MDS case: a perpendicular dipole located at the center of the dielectric (d + = 10 nm). It is notable that, although the decay rate density spectra for the MDSD and MDS cases differ considerably due to the possibility of coupling to a well-defined hybrid SPP/Si-waveguide-like mode in the former (cf. Figs. 3a and 3b), the overall spontaneous emission rate enhancements for the two structures are very similar. The black dashed line describes a device which would more likely be produced by a typical fabrication scheme: a finite MDSD structure (layer thicknesses as shown in Fig. 3b) with randomly-oriented, uniformly-excited emitters distributed throughout a region of the dielectric layer (d + ∊ [1.5,18.5] nm), rather than being confined to a plane at the center. This situation would more realistically model a device using, for example, Si nanocrystals (NCs) formed via ion implantation for the emitters. Although the SP resonance peak at ~370 nm is much higher than the case with dipoles at the dielectric center (due to the presence of emitters very close to the metal surface), the behavior in the non-resonant regime is comparable. It should be borne in mind that the fraction of power coupled into the useful SPP guided mode is a strong function of the dipole position (see the inset to Fig. 3b). As a result, the averaged enhancement shown in the black dashed plot is only representative of the overall decay rate in the ensemble and not specifically that of the SPP mode emission. The emitters closest to the metal would have the most rapid decay rate, but this power is inaccessible since it is lost to absorptive quenching processes. On the other hand, while the emitters which are closer to the oxide–silicon interface would not experience as high decay rates, they would couple most strongly to the useful guided mode.

So far, we have considered ideal emitters with unit internal quantum efficiency (η = 1). In practice, however, this is rarely the case; continuing with the foregoing example, wellpassivated Si NCs can have η ≈ 0.6 [19

19. R. J. Walters, J. Kalkman, A. Polman, H. A. Atwater, and M. J. A. de Dood, “Photoluminescence quantum efficiency of dense silicon nanocrystal ensembles in SiO2,” Phys. Rev. B 73, 132302 (2006). [CrossRef]

]. In Fig. 4b, for perpendicular dipoles at the center of the dielectric in the finite MDSD structure shown in the inset, we consider the effect of the emitters’ internal quantum efficiency on the decay rate enhancement: a reduction in the quantum efficiency yields essentially a linear reduction in the decay rate enhancement for the wavelength range shown. From this result, we see that even for non-ideal emitters, a strong non-resonant enhancement in the decay rate is possible, further suggesting the viability of this architecture for an on-chip light source.

From an integrated photonics perspective, it is also important to consider the behavior of a MDS structure containing only standard materials used in integrated microelectronics fabrication processes; fortuitously, replacing the semi-infinite silver layer with CMOS-compatible aluminum yields very similar results. For a MDSD structure in analogy to Fig. 3b, approximately 79% of the emission at 1535 nm is coupled into the hybrid plasmonic/dielectric guided mode discussed previously. Furthermore, γ̂ ranges from ~25 to 55 between 600 and 1800 nm, achieving a value of 50 at 1.5 μm. We therefore suggest that, despite its somewhat greater absorptive loss in the visible and near infrared, Al may also be used to obtain similar, substantial enhancements in emission rate across a broad wavelength range. Although this paper focuses on the optical characteristics of the emitters, it is worth noting that careful design of the emitter-containing layer may be necessary to yield the efficient electroluminescence required for a viable integrated photonics component. For instance, improved charge injection through the dielectric layer would be possible if silicon nitride rather than silicon dioxide is used for the dielectric layer [20

20. K. S. Cho, N. M. Park, T. Y. Kim, K. H. Kim, G. Y. Sung, and J. H. Shin, “High efficiency visible electroluminescence from silicon nanocrystals embedded in silicon nitride using a transparent doping layer”, Appl. Phys. Lett. 86, 071909 (2005). [CrossRef]

]. Using a higher-index dielectric would have the effect of reducing the overall enhancement somewhat due to the smaller dielectric contrast between the layers.

4. Conclusion

We have investigated spontaneous emission enhancements in planar MOS structures by considering the response of a semiclassical oscillating dipole at the center of a 20-nm-thick silica layer clad by semi-infinite Ag and Si layers. The decay rate density for TM modes is dominated by leaky radiation modes into the Si substrate, with additional absorptive loss at high k due to the proximity of the metal. The simulations predict radiative decay rate enhancements of 40 to 60 over a broad wavelength range (600 to 1800 nm) away from the Ag–SiO2 surface plasmon resonance. Similar behavior is observed for finite-thickness metal–oxide–silicon–oxide structures. This enables strong preferential coupling into a single, well-defined waveguide mode, suggesting a viable pathway toward a new class of power-efficient, monolithically-integrated, CMOS-compatible light sources for all-silicon optoelectronics applications.

Acknowledgements

References and links

1.

B. Jalali and S. Fathpour, “Silicon photonics,” J. Lightwave Tech. 24, 4600–4615 (2006). [CrossRef]

2.

M. Lipson, “Guiding, modulating, and emitting light on silicon—Challenges and opportunities,” J. Lightwave Tech. 23, 4222–4238 (2005). [CrossRef]

3.

L. Pavesi, “Will silicon be the photonic material of the third millenium?” J. Phys. Condens. Matter 15, R1169–R1196 (2003). [CrossRef]

4.

L. Pavesi, L. Dal Negro, C. Mazzoleni, G. Franzò, and F. Priolo, “Optical gain in silicon nanocrystals,” Nature 408, 440–444 (2000). [CrossRef] [PubMed]

5.

A. W. Fang, H. Park, O. Cohen, R. Jones, M. J. Paniccia, and J. E. Bowers, “Electrically pumped hybrid AlGaInAs-silicon evanescent laser,” Opt. Express 14, 9203–9210 (2006). [CrossRef] [PubMed]

6.

G. W. Ford and W. H. Weber, “Electromagnetic interactions of molecules with metal surfaces,” Phys. Rep. 113, 195–287 (1984). [CrossRef]

7.

W. L. Barnes, “Electromagnetic crystals for surface plasmon polaritons and the extraction of light from emissive devices,” J. Lightwave Tech. 17, 2170–2182 (1999). [CrossRef]

8.

J. Vučković, M. Loncar, and A. Scherer, “Surface plasmon enhanced light-emitting diode,” IEEE J. Quantum Electron. 36, 1131–1144 (2000). [CrossRef]

9.

J. S. Q. Liu and M. Brongersma, “Omnidirectional light emission via surface plasmon polaritons,” Appl. Phys. Lett. 90, 091116 (2007). [CrossRef]

10.

Y. C. Jun, R. D. Kekatpure, J. S. White, and M. Brongersma, “Nonresonant enhancement of spontaneous emission in metal-dielectric-metal plasmon waveguide structures,” Phys. Rev. B 78, 153111 (2008). [CrossRef]

11.

S. Wang, A. Eckau, E. Neufeld, R. Carius, and C. Buchal, “Hot electron impact excitation cross-section of Er3+ and electroluminescence from erbium-implanted silicon metal-oxide-semiconductor tunnel diodes,” Appl. Phys. Lett. 71, 2824–2826 (1997). [CrossRef]

12.

K. Sun, W. J. Xu, B. Zhang, L. P. You, G. Z. Ran, and G. G. Qin, “Strong enhancement of Er3+ 1.54 μm electroluminescence through amorphous Si nanoparticles,” Nanotechnology 19, 105,708 (2008).

13.

A. Irrera, D. Pacifici, M. Miritello, G. Franzò, F. Priolo, F. Iacona, D. Sanfillipo, G. Di Stefano, and P. G. Fallica, “Electroluminescence properties of light emitting devices based on silicon nanocrystals,” Physica E 16, 395–399 (2003). [CrossRef]

14.

P. Yeh, Optical waves in layered media, 2nd ed. (Wiley-Interscience, New York, 2005).

15.

A. D. Rakić, A. B. Djurišić, J. M. Elazar, and M. L. Majewski, “Optical properties of metallic films for vertical-cavity optoelectronic devices,” Appl. Opt. 37, 5271–2383 (1998). [CrossRef]

16.

D. R. Lide, ed., CRC Handbook of Chemistry and Physics, Internet Version 2008, 88th ed. (Taylor & Francis, Boca Raton, FL, 2008).

17.

J. J. Burke, G. I. Stegeman, and T. Tamir, “Surface-polariton-like waves guided by thin, lossy metal films,” Phys. Rev. B 33, 5186–5201 (1986). [CrossRef]

18.

G. T. Reed and A. P. Knights, Silicon photonics: an introduction (John Wiley and Sons, Ltd., Chichester, England, 2004). [CrossRef]

19.

R. J. Walters, J. Kalkman, A. Polman, H. A. Atwater, and M. J. A. de Dood, “Photoluminescence quantum efficiency of dense silicon nanocrystal ensembles in SiO2,” Phys. Rev. B 73, 132302 (2006). [CrossRef]

20.

K. S. Cho, N. M. Park, T. Y. Kim, K. H. Kim, G. Y. Sung, and J. H. Shin, “High efficiency visible electroluminescence from silicon nanocrystals embedded in silicon nitride using a transparent doping layer”, Appl. Phys. Lett. 86, 071909 (2005). [CrossRef]

OCIS Codes
(130.0250) Integrated optics : Optoelectronics
(160.3900) Materials : Metals
(160.6000) Materials : Semiconductor materials
(230.6080) Optical devices : Sources
(240.6680) Optics at surfaces : Surface plasmons
(250.5403) Optoelectronics : Plasmonics

ToC Category:
Optoelectronics

History
Original Manuscript: October 16, 2008
Revised Manuscript: December 19, 2008
Manuscript Accepted: December 22, 2008
Published: December 24, 2008

Citation
Aaron Hryciw, Young Chul Jun, and Mark L. Brongersma, "Plasmon-enhanced emission from optically-doped MOS light sources," Opt. Express 17, 185-192 (2009)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-1-185


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. B. Jalali and S. Fathpour, "Silicon photonics," J. Lightwave Tech. 24, 4600-4615 (2006). [CrossRef]
  2. M. Lipson, "Guiding, modulating, and emitting light on silicon—Challenges and opportunities," J. Lightwave Tech. 23, 4222-4238 (2005). [CrossRef]
  3. L. Pavesi, "Will silicon be the photonic material of the third millenium?" J. Phys. Condens. Matter 15, R1169- R1196 (2003). [CrossRef]
  4. L. Pavesi, L. Dal Negro, C. Mazzoleni, G. Franzò, and F. Priolo, "Optical gain in silicon nanocrystals," Nature 408, 440-444 (2000). [CrossRef] [PubMed]
  5. A. W. Fang, H. Park, O. Cohen, R. Jones, M. J. Paniccia, and J. E. Bowers, "Electrically pumped hybrid AlGaInAs-silicon evanescent laser," Opt. Express 14, 9203-9210 (2006). [CrossRef] [PubMed]
  6. G. W. Ford and W. H. Weber, "Electromagnetic interactions of molecules with metal surfaces," Phys. Rep. 113, 195-287 (1984). [CrossRef]
  7. W. L. Barnes, "Electromagnetic crystals for surface plasmon polaritons and the extraction of light from emissive devices," J. Lightwave Tech. 17, 2170-2182 (1999). [CrossRef]
  8. J. Vu?kovi?, M. Loncar, and A. Scherer, "Surface plasmon enhanced light-emitting diode," IEEE J. Quantum Electron. 36, 1131-1144 (2000). [CrossRef]
  9. J. S. Q. Liu and M. Brongersma, "Omnidirectional light emission via surface plasmon polaritons," Appl. Phys. Lett. 90, 091116 (2007). [CrossRef]
  10. Y. C. Jun, R. D. Kekatpure, J. S. White, and M. Brongersma, "Nonresonant enhancement of spontaneous emission in metal-dielectric-metal plasmon waveguide structures," Phys. Rev. B 78, 153111 (2008). [CrossRef]
  11. S. Wang, A. Eckau, E. Neufeld, R. Carius, and C. Buchal, "Hot electron impact excitation cross-section of Er3+ and electroluminescence from erbium-implanted silicon metal-oxide-semiconductor tunnel diodes," Appl. Phys. Lett. 71, 2824-2826 (1997). [CrossRef]
  12. K. Sun, W. J. Xu, B. Zhang, L. P. You, G. Z. Ran, and G. G. Qin, "Strong enhancement of Er3+ 1.54 ?m electroluminescence through amorphous Si nanoparticles," Nanotechnology 19, 708 (2008).
  13. A. Irrera, D. Pacifici, M. Miritello, G. Franzò, F. Priolo, F. Iacona, D. Sanfillipo, G. Di Stefano, and P. G. Fallica, "Electroluminescence properties of light emitting devices based on silicon nanocrystals," Physica E 16, 395-399 (2003). [CrossRef]
  14. P. Yeh, Optical waves in layered media, 2nd ed. (Wiley-Interscience, New York, 2005).
  15. A. D. Raki?, A. B. Djurisi?, J. M. Elazar, and M. L. Majewski, "Optical properties of metallic films for verticalcavity optoelectronic devices," Appl. Opt. 37, 5271-5283 (1998). [CrossRef]
  16. D. R. Lide, ed., CRC Handbook of Chemistry and Physics, Internet Version 2008, 88th ed. (Taylor & Francis, Boca Raton, FL, 2008).
  17. J. J. Burke, G. I. Stegeman, and T. Tamir, "Surface-polariton-like waves guided by thin, lossy metal films," Phys. Rev. B 33, 5186-5201 (1986). [CrossRef]
  18. G. T. Reed and A. P. Knights, Silicon photonics: an introduction (JohnWiley and Sons, Ltd., Chichester, England, 2004). [CrossRef]
  19. R. J. Walters, J. Kalkman, A. Polman, H. A. Atwater, and M. J. A. de Dood, "Photoluminescence quantum efficiency of dense silicon nanocrystal ensembles in SiO2," Phys. Rev. B 73, 132302 (2006). [CrossRef]
  20. K. S. Cho, N. M. Park, T. Y. Kim, K. H. Kim, G. Y. Sung, and J. H. Shin, "High efficiency visible electroluminescence from silicon nanocrystals embedded in silicon nitride using a transparent doping layer", Appl. Phys. Lett. 86, 071909 (2005). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1. Fig. 2. Fig. 3.
 
Fig. 4.
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited