OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 17, Iss. 17 — Aug. 17, 2009
  • pp: 15001–15007
« Show journal navigation

Continuous wave terahertz systems exploiting 1.5 µm telecom technologies

B. Sartorius, M. Schlak, D. Stanze, H. Roehle, H. Künzel, D. Schmidt, H.-G. Bach, R. Kunkel, and M. Schell  »View Author Affiliations


Optics Express, Vol. 17, Issue 17, pp. 15001-15007 (2009)
http://dx.doi.org/10.1364/OE.17.015001


View Full Text Article

Acrobat PDF (415 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

A fiber-assembled CW THz System operating at 1.5 µm is presented. High speed telecom photodiodes integrated with planar THz antennas serve as THz emitters with power up to 10 µW. Photoconductive antennas based on LT InGaAs/InAlAs multi-layer structures allow coherent detection. The system operates in a wide frequency range of 0.1 −1.6 THz.

© 2009 OSA

1. Introduction

Terahertz spectroscopy promises attractive applications in various fields such as security, medicine, science, and non-destructive material testing [1

1. M. Tonouchi, “„Cutting-edge terahertz technology,” Nat. Photonics 1(2), 97–105 (2007). [CrossRef]

]. THz systems, however, are presently bulky, expensive, and often need cryogenic cooling, thus preventing broader practical application. Exploiting mature telecom technologies is one promising way towards achieving compact and low cost Terahertz systems. This paper focuses on continuous wave (CW) THz systems and their improvements by using telecom technologies.

The big advantage of CW THz generation vs. time domain (TD) THz generation is its simple optical source. Only two single mode CW lasers are needed, with at least one of them tunable. Especially at the telecom wavelength 1.5 µm, a large variety of compact, tunable and low cost semiconductor lasers is already available.

The challenge for CW systems, on the other hand, is to achieve sufficient THz power. Photoconductive antennas (PCAs) work well in pulsed systems with high peak power at a moderate repetition rate. However, they have up to now had severe limitations as photomixer emitters in CW operation. Using LT-GaAs photomixers, THz power of 0.2 µW at 100 GHz is reported in [2

2. A. J. Deninger, T. Göbel, D. Schönherr, T. Kinder, A. Roggenbuck, M. Köberle, F. Lison, T. Müller-Wirts, and P. Meissner, “Precisely tunable continuous-wave terahertz source with interferometric frequency control,” Rev. Sci. Instrum. 79(4), 044702 (2008). [CrossRef] [PubMed]

]. Emcore developed ErAs:GaAs based photomixers, also for operation at 800 nm, and achieved 4 µW at 100 GHz [3].

Ion irradiated InGaAs has been developed and evaluated as a possible photomixer for use at the telecom wavelength of 1550 nm [4

4. M. Martin, J. Mangeney, P. Crozat, Y. Chassagneux, R. Colombelli, N. Zerounian, L. Vivien, and K. Blary, “Gigahertz modulation of tunable terahertz radiation from photomixers driven at telecom wavelengths,” Appl. Phys. Lett. 93(13), 131112 (2008). [CrossRef]

]. However, much less THz power compared to the 800 nm solution of [2

2. A. J. Deninger, T. Göbel, D. Schönherr, T. Kinder, A. Roggenbuck, M. Köberle, F. Lison, T. Müller-Wirts, and P. Meissner, “Precisely tunable continuous-wave terahertz source with interferometric frequency control,” Rev. Sci. Instrum. 79(4), 044702 (2008). [CrossRef] [PubMed]

,3] was reported (45 nW at 100 GHz), detectable only with cooled bolometers. Obviously, the exploitation of telecom technologies for CW THz systems requires improved THz emitters.

2. Development of 1.5 µm operated telecom based emitters

Fortunately, telecom technology offers alternative devices for THz generation: photodiodes with integrated antennas. While speed up of photoconductors is achieved by incorporating fast recombination centers - which at the same time reduce the efficiency of the photo effect - the speed of the diodes is limited by the transit time through the pin structure. In pioneering work, NTT in Japan developed the Uni-Traveling-Carrier (UTC) photodiode structure, where only the fast electrons - not the slow holes - limit the device speed [5

5. H. Ito, F. Nakajima, T. Furuta, and T. Ishibashi, “Continuous THz-wave generation using antenna-integrated uni-travelling-carrier photodiodes,” Semicond. Sci. Technol. 20(7), 191–198 (2005). [CrossRef]

]. They were able to demonstrate THz emission of about 2 µW at 1 THz. By optimizing the UTC concept and combining it with resonant antennas, other institutions have published THz emission powers of more than 100 µW at 400 GHz [6

6. C. C Renaud, M. Robertson, R. Firth, P. J. Cannard, R. Moore, and A. J. Seeds, “A high responsivity, broadband waveguide uni-travelling carrier photodiode,” Proc. SPIE 6194, 61940C (2006). [CrossRef]

]. Photodiode-based emitters are obviously the superior devices for optoelectronic CW systems.

We use another approach for high speed photodiodes: waveguide integrated devices. Using standard surface illuminated pin photodiodes (Fig. 1a
Fig. 1 Scheme of photodiode structures: (a) surface illuminated, (b) waveguide integrated
) and minimizing the thickness of the active layer leads to a higher speed - but on the other hand directly reduces the absorption and the efficiency. Waveguide integrated photodiodes (Fig. 1b), however behave like side illuminated devices, and high absorption even for thin active layers can be achieved. High speed and high efficiency can therefore be combined.

In the HHI waveguide integrated photodiodes have already been developed for telecom applications in the 1.5 µm wavelength range. These devices belong to the fastest worldwide, and they are suitable for additional antenna integration. The scheme of the HHI photodiode is shown in Fig. 2
Fig. 2 Photodiode (win-PDA) THz emitter: (a) scheme, (b) antenna, (c) contacted chip on lens
. The InGaAs/InGaAsP heterostructure is grown on semi-insulating InP substrates using MOVPE. The active layer has an effective thickness of about 0.3 µm. The waveguide includes a taper (Fig. 2a) for improved fiber-chip coupling. The processed photodiodes have a length of 20 µm and a width of 7 µm respectively, and are located above the waveguide. The control light is injected at the facet into the tapered structure and directed by the waveguide to the diode. There it is coupled into the active layer and absorbed. Further details on structure and processing are given in [7

7. H-.G. Bach, A. Beling, G. G. Mekonnen, R. Kunkel, D. Schmidt, W. Ebert, A. Seeger, M. Stollberg, and W. Schlaak, “InP-Based Waveguide-Integrated Photodetector With 100-GHz Bandwidth,” IEEE J. Sel. Top. Quantum Electron. 10, 668–672 (2004). [CrossRef]

].

On top of the photodiode, on an isolating nitride layer, bow tie antennas (size 160 µm, Fig. 2b), were integrated with electrical contacts to the diode. The bow tie antennas radiate in defined linear polarization, and the emission spectrum is broadband. We call this new device combining a waveguide integrated PhotoDiode with a THz Antenna “win-PDA”.

The photodiode chips are cleaved, and the input facets are anti-reflection coated. As a first device test, the emission power of the win-PDA was measured using a manufacturer-calibrated Golay cell. At 200 GHz and for an optical input power of 30 mW, a THz output power of 10 µW was achieved. This is below the results for the best UTC devices but clearly better than the photoconductive antenna based photomixers. Thus the design and technology of the first wafer were successful, and the devices can be used as THz emitters.

3. Development of 1.5 µm operated coherent receivers

Photodiodes with integrated antennas (PDAs) have proved to be improved emitters. However, a completely photodiode based THz system is not feasible since these devices are not suitable for coherent detection. Illuminated photodiodes emit a current and voltage output signal even without a THz field applied via the antenna, and thus a mixing effect similar as in the photoconductive antennas cannot be achieved. On the receiver side PCAs are indispensible for coherent detection. The problem is that the commonly available LT GaAs PCAs work only for wavelengths in the 800 nm range, while PDA based emitters have so far only been developed for 1.5 µm operation. Therefore, all photodiode based emitters have been used with incoherent detection by means of Golay cells or bolometers. The full benefit of PDA emitters can only be exploited once coherent receivers for 1.5 µm operation become available.

In HHI the fundamental problem of LT (200°C) MBE grown InGaAs on InP, namely the high dark conductivity, has recently been solved. Two techniques were combined: First, conventional compensation of the electron concentration by balanced doping with Be acceptors. Second, in a novel attempt, very thin (12 nm) photoconductive layers were embedded between InAlAs layers with higher bandgap (transparent for 1.5 µm). The essential feature of the InAlAs exploited here is the existence of deep trapping centers. The residual electrons are captured by the InAlAs, resulting in a sheet resistivity up to 106 Ω/sq.

For achieving sufficient absorption a sequence of 100 periods of this layer structure has been grown (Fig. 3a
Fig. 3 Coherent photoconductive receiver: (a) heterostructure, (b) antenna chip, (c) fiber coupled module
). The performance of this material for operation up to 3 THz has already been demonstrated in time domain spectrometers with strip line emitters and dipole receivers [8

8. B. Sartorius, H. Roehle, H. Künzel, J. Böttcher, M. Schlak, D. Stanze, H. Venghaus, and M. Schell, “All-fiber terahertz time-domain spectrometer operating at 1.5 microm telecom wavelengths,” Opt. Express 16(13), 9565–9570 (2008). [CrossRef] [PubMed]

]. For our photomixer application, we use the same material with one exception - bow tie antennas are used, similar to the diode emitter. The 90° bow ties are 3 mm long on 4x4 mm chips and the gap is 10x10 µm (Fig. 3b). These antenna chips are packaged into modules (Fig. 3c). A standard single mode fiber is fixed to the module. The excitation light can be launched via an FC/APC connector into the fiber and to the antenna, and the Si lens for coupling out the THz radiation can be seen on the front of the module. An SMA connector is available for measuring the photocurrent.

4. Assembly of CW system with photodiode emitter and coherent receiver

5. Performance of the assembled CW system

The bandwidth and performance of the setup were investigated by tuning the wavelength difference of the two ECLs and thus the beating frequency of the optical control signal. The optical power (measured in the fiber) was 30 mW at the emitter and 40 mW at the receiver. The photocurrent in the PC antenna (pre-amplified 108 V/A) was measured with the lock-in technique at 460 Hz modulation frequency. Integration and acquisition time were adapted to the signal amplitude: 30 ms / 100 ms at high amplitude (< 500 GHz), 300 ms / 1 s for low amplitude (> 1 THz), and 100 ms / 300 ms in the intermediate range. The tuning of the fiber delay line was computer controlled, and the amplitude of the receiver current versus time delay was measured. Figure 5a
Fig. 5 THz signal: (a) measured vs. time delay, (b) measured vs. frequency (steps 5 GHz)
shows the according sine trace for several measurements within three hours. The traces match very well, indicating the excellent stability of the signal in amplitude and phase. Increasing the wavelength difference of the ECLs from 0.1 nm to 13 nm, adjusting the phase condition correctly, and recording the amplitude of the signal gives us the curve in Fig. 5b. The dips observed in the curve correspond almost exactly to the known absorption lines of water vapor in air. Our CW system operates up to 1.6 THz with a good signal to noise ratio, an excellent value for the first generation of our diode chips.

6. Application examples of the CW THz system

The second advantage of a CW system is the measurement speed if the significant information can be extracted by measurements at a fixed frequency. As an example we monitored the water vapor in air over a period of time by measuring the absorption at the significant frequency of 0.556 THz. The water vapor content was varied in the test tube by switching between streams of wet or dry nitrogen (Fig. 7a
Fig. 7 Absorption versus time: (a) setup, (b) signal versus time
). The measured THz signal versus time is shown in Fig. 7b. The monitoring speed in this case is 100 ms, much faster than the gas exchange.

This proves the practical application of a gas monitoring technique that is even able to pierce tubes made of opaque plastic materials.

7. Summary and outlook

Size and costs of THz systems can be significantly reduced by replacing the pulsed lasers by continuous semiconductor lasers at the telecom wavelength 1.5 µm. The most critical components in a CW system are the emitters. Photoconductive antennas, while working excellently in TD systems, emit only low power in CW operation. High speed telecom photodiodes modified to integrate a THz antenna promise higher output power.

Combining these high THz output power photodiode antennas as emitters with sensitive coherent detection requires the operation of the both at the same wavelength. In this paper, we have presented the first CW system combining a photodiode antenna based emitter with a coherent photoconductive receiver. Both devices were fabricated at the HHI exploiting mature telecom InP technology. THz power up to 10 µW at 200 GHz was achieved with our first design iteration, and the operation of the system up to 1.6 THz was demonstrated. The complete system was assembled using fiber technology. Our CW system will pave the way to flexible, robust and transportable systems at moderate cost - handheld in size and price.

References and links

1.

M. Tonouchi, “„Cutting-edge terahertz technology,” Nat. Photonics 1(2), 97–105 (2007). [CrossRef]

2.

A. J. Deninger, T. Göbel, D. Schönherr, T. Kinder, A. Roggenbuck, M. Köberle, F. Lison, T. Müller-Wirts, and P. Meissner, “Precisely tunable continuous-wave terahertz source with interferometric frequency control,” Rev. Sci. Instrum. 79(4), 044702 (2008). [CrossRef] [PubMed]

3.

www.emcore.com/fiber_optics

4.

M. Martin, J. Mangeney, P. Crozat, Y. Chassagneux, R. Colombelli, N. Zerounian, L. Vivien, and K. Blary, “Gigahertz modulation of tunable terahertz radiation from photomixers driven at telecom wavelengths,” Appl. Phys. Lett. 93(13), 131112 (2008). [CrossRef]

5.

H. Ito, F. Nakajima, T. Furuta, and T. Ishibashi, “Continuous THz-wave generation using antenna-integrated uni-travelling-carrier photodiodes,” Semicond. Sci. Technol. 20(7), 191–198 (2005). [CrossRef]

6.

C. C Renaud, M. Robertson, R. Firth, P. J. Cannard, R. Moore, and A. J. Seeds, “A high responsivity, broadband waveguide uni-travelling carrier photodiode,” Proc. SPIE 6194, 61940C (2006). [CrossRef]

7.

H-.G. Bach, A. Beling, G. G. Mekonnen, R. Kunkel, D. Schmidt, W. Ebert, A. Seeger, M. Stollberg, and W. Schlaak, “InP-Based Waveguide-Integrated Photodetector With 100-GHz Bandwidth,” IEEE J. Sel. Top. Quantum Electron. 10, 668–672 (2004). [CrossRef]

8.

B. Sartorius, H. Roehle, H. Künzel, J. Böttcher, M. Schlak, D. Stanze, H. Venghaus, and M. Schell, “All-fiber terahertz time-domain spectrometer operating at 1.5 microm telecom wavelengths,” Opt. Express 16(13), 9565–9570 (2008). [CrossRef] [PubMed]

9.

R. J. Foltynowicz and R. E. Allman, “Terahertz Time-Domain Spectroscopy of Atmospheric Water Vapor From 0.4 to 2.7 THz,” Sandia Report, October 2005.

OCIS Codes
(120.4290) Instrumentation, measurement, and metrology : Nondestructive testing
(300.6495) Spectroscopy : Spectroscopy, teraherz

ToC Category:
Spectroscopy

History
Original Manuscript: May 12, 2009
Revised Manuscript: July 3, 2009
Manuscript Accepted: July 15, 2009
Published: August 10, 2009

Citation
B. Sartorius, M. Schlak, D. Stanze, H. Roehle, H. Künzel, D. Schmidt, H.-G. Bach, R. Kunkel, and M. Schell, "Continuous wave terahertz systems exploiting 1.5 µm telecom technologies," Opt. Express 17, 15001-15007 (2009)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-17-15001


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. M. Tonouchi, “„Cutting-edge terahertz technology,” Nat. Photonics 1(2), 97–105 (2007). [CrossRef]
  2. A. J. Deninger, T. Göbel, D. Schönherr, T. Kinder, A. Roggenbuck, M. Köberle, F. Lison, T. Müller-Wirts, and P. Meissner, “Precisely tunable continuous-wave terahertz source with interferometric frequency control,” Rev. Sci. Instrum. 79(4), 044702 (2008). [CrossRef] [PubMed]
  3. www.emcore.com/fiber_optics
  4. M. Martin, J. Mangeney, P. Crozat, Y. Chassagneux, R. Colombelli, N. Zerounian, L. Vivien, and K. Blary, “Gigahertz modulation of tunable terahertz radiation from photomixers driven at telecom wavelengths,” Appl. Phys. Lett. 93(13), 131112 (2008). [CrossRef]
  5. H. Ito, F. Nakajima, T. Furuta, and T. Ishibashi, “Continuous THz-wave generation using antenna-integrated uni-travelling-carrier photodiodes,” Semicond. Sci. Technol. 20(7), 191–198 (2005). [CrossRef]
  6. C. C Renaud, M. Robertson, R. Firth, P. J. Cannard, R. Moore, and A. J. Seeds, “A high responsivity, broadband waveguide uni-travelling carrier photodiode,” Proc. SPIE 6194, 61940C (2006). [CrossRef]
  7. H-.G. Bach, A. Beling, G. G. Mekonnen, R. Kunkel, D. Schmidt, W. Ebert, A. Seeger, M. Stollberg, and W. Schlaak, “InP-Based Waveguide-Integrated Photodetector With 100-GHz Bandwidth,” IEEE J. Sel. Top. Quantum Electron. 10, 668–672 (2004). [CrossRef]
  8. B. Sartorius, H. Roehle, H. Künzel, J. Böttcher, M. Schlak, D. Stanze, H. Venghaus, and M. Schell, “All-fiber terahertz time-domain spectrometer operating at 1.5 microm telecom wavelengths,” Opt. Express 16(13), 9565–9570 (2008). [CrossRef] [PubMed]
  9. R. J. Foltynowicz and R. E. Allman, “Terahertz Time-Domain Spectroscopy of Atmospheric Water Vapor From 0.4 to 2.7 THz,” Sandia Report, October 2005.

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited