OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 17, Iss. 24 — Nov. 23, 2009
  • pp: 21628–21633
« Show journal navigation

A self-Q-switched all-fiber erbium laser at 1530 nm using an auxiliary 1570-nm erbium laser

Tzong-Yow Tsai and Yen-Cheng Fang  »View Author Affiliations


Optics Express, Vol. 17, Issue 24, pp. 21628-21633 (2009)
http://dx.doi.org/10.1364/OE.17.021628


View Full Text Article

Acrobat PDF (554 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We demonstrate a self-Q-switched, all-fiber, tunable, erbium laser at 1530 nm with high pulse repetition rates of 0.9-10 kHz. Through the use of an auxiliary 10-mW, 1570 nm laser that shortened the relaxation time of erbium, sequentially Q-switched pulses with pulse energies between 4 and 6 μJ and pulse widths of 40 ns were steadily achieved. A peak pulse power of 165 W was obtained.

© 2009 OSA

1. Introduction

Fiber lasers have been Q-switched using traditional bulk Q-switches and fiber-pigtailed ones. Sophisticated alignment techniques were necessary for reducing the coupling losses between the bulk Q-switches and the fiber cores. High-power, multimode pump diodes, double-cladding fibers and pump-signal combiners were often employed to increase pump efficiency and build up large laser gains that compensated for the coupling losses. All-fiber Q-switched lasers with fiber-pigtailed Q-switches are of great interest because of their alignment-free characteristics and low cavity loss that is essential for efficient Q-switching performance. The fiber-pigtail Q-switches can be active devices as piezoelectric actuators [1

1. N. A. Russo, R. Duchowicz, J. Mora, J. L. Cruz, and M. V. Andrés, “High-efficiency Q-switched erbium fiber laser using a Bragg grating-based modulator,” Opt. Commun. 210(3-6), 361–366 ( 2002). [CrossRef]

], acousto-optical modulators [2

2. D. W. Huang, W. F. Liu, and C. C. Yang, “Q-switched all-fiber laser with an acoustically modulated fiber attenuator,” IEEE Photon. Technol. Lett. 12(9), 1153–1155 ( 2000). [CrossRef]

4

4. M. Delgado-Pinar, D. Zalvidea, A. Díez, P. Pérez-Millan, and M. V. Andrés, “Q-switching of an all-fiber laser by acousto-optic modulation of a fiber Bragg grating,” Opt. Express 14(3), 1106–1112 ( 2006). [CrossRef] [PubMed]

] and magnetostrictive transducers [5

5. P. Pérez-Millán, A. Díez, M. V. Andrés, D. Zalvidea, and R. Duchowicz, “Q-switched all-fiber laser based on magnetostriction modulation of a Bragg grating,” Opt. Express 13(13), 5046–5051 ( 2005). [CrossRef] [PubMed]

], or passive ones such as semiconductor saturable-absorber mirrors (SESAM) [6

6. R. Paschotta, R. Häring, E. Gini, H. Melchior, U. Keller, H. L. Offerhaus, and D. J. Richardson, “Passively Q-switched 0.1-mJ fiber laser system at 1.53 mum,” Opt. Lett. 24(6), 388–390 ( 1999). [CrossRef] [PubMed]

,7

7. S. Kivistö, R. Koskinen, J. Paajaste, S. D. Jackson, M. Guina, and O. G. Okhotnikov, “Passively Q-switched Tm3+, Ho3+-doped silica fiber laser using a highly nonlinear saturable absorber and dynamic gain pulse compression,” Opt. Express 16(26), 22058–22063 ( 2008). [CrossRef] [PubMed]

] and saturable-absorber fibers [8

8. V. V. Dvoyrin, V. M. Mashinsky, and E. M. Dianov, “Yb-Bi pulsed fiber lasers,” Opt. Lett. 32(5), 451–453 ( 2007). [CrossRef] [PubMed]

12

12. S. D. Jackson, “Passively Q-switched Tm(3+)-doped silica fiber lasers,” Appl. Opt. 46(16), 3311–3317 ( 2007). [CrossRef] [PubMed]

]. Passive Q-switching with a saturable absorber fiber is the simplest and most economical approach for producing high-power laser pulses. In addition, a solid-state saturable absorber Q-switch (SAQS) fiber has a high damage threshold and can hold an enormous laser gain for energy release into one Q-switched laser pulse. In spite of these advantages, the SAQS fibers are seldom considered in the literature. One of the criteria for a SAQS laser is that the absorption cross section, σa, of the SAQS should be larger that the emission cross section, σe, of the gain medium. Furthermore, to achieve sequentially Q-switched pulses using a continuous-wave (CW) pump source, the relaxation lifetime of the SAQS, τa2, should be shorter than that of the gain medium, τg2. There has been a breakthrough in the last four years in finding SAQS fibers for ytterbium fiber lasers. Fibers doped with bismuth [8

8. V. V. Dvoyrin, V. M. Mashinsky, and E. M. Dianov, “Yb-Bi pulsed fiber lasers,” Opt. Lett. 32(5), 451–453 ( 2007). [CrossRef] [PubMed]

] and rare earth ions such as samarium [9

9. A. A. Fotiadi, A. S. Kurkov, and I. M. Razdobreev, “All-fiber passively Q-switched Ytterbium laser,” 2005 Conference on Lasers and Electro-Optics Europe, p. 515.

], thulium [10

10. P. Adel, M. Auerbach, C. Fallnich, S. Unger, H.-R. Müller, and J. Kirchhof, “Passive Q-switching by Tm3+co-doping of a Yb3+-fiber laser,” Opt. Express 11(21), 2730–2735 ( 2003). [CrossRef] [PubMed]

] and holmium [11

11. A. S. Kurkov, E. M. Sholokhov, and O. I. Medvedkov, “All fiber Yb-Ho pulsed laser,” Laser Phys. Lett. 6(2), 135–138 ( 2009). [CrossRef]

] have been demonstrated as efficient SAQS materials for ytterbium fiber lasers within the wavelength range from 1050 nm to 1125 nm where the σe of Yb is relatively small. Moreover, a Ho-doped fiber was reported as a SAQS fiber for use in a Tm fiber laser operating at 2-2.1 μm [12

12. S. D. Jackson, “Passively Q-switched Tm(3+)-doped silica fiber lasers,” Appl. Opt. 46(16), 3311–3317 ( 2007). [CrossRef] [PubMed]

].

Erbium fiber lasers emitting at the so-called eye-safe wavelength of 1.5-1.6 μm are the preferred laser devices for light detection and ranging (LIDAR) and other applications that require Q-switched operation. Few bulk crystals such as U:CaF2 [13

13. R. D. Stultz, M. B. Camargo, and M. Birnbaum, “Passive Q-switch at 1.53 µm using divalent uranium ions in calcium fluoride,” J. Appl. Phys. 78(5), 2959–2961 ( 1995). [CrossRef]

] Co:ZnS and Co:ZnSe [14

14. T.-Y. Tsai and M. Birnbaum, “Co2+:ZnS and Co2+:ZnSe Saturable Absorber Q-switches,” J. Appl. Phys. 87(1), 25–29 ( 2000). [CrossRef]

] have been reported to be efficient SAQS materials for Er:glass lasers. Nevertheless, there has been no fiber-type SAQS material demonstrated for erbium fiber lasers except for erbium fiber itself. Recently, we demonstrated self-Q-switched, all-fiber erbium lasers in a ring scheme [15

15. T.-Y. Tsai and Y.-C. Fang, “A saturable absorber Q-switched all-fiber ring laser,” Opt. Express 17(3), 1429–1434 ( 2009). [CrossRef] [PubMed]

] and a standing-wave resonator [16

16. T.-Y. Tsai, Y.-C. Fang, Z.-C. Lee, and H.-X. Tsao, “All-fiber passively Q-switched erbium laser using mismatch of mode field areas and a saturable-amplifier pump switch,” Opt. Lett. 34(19), 2891–2893 ( 2009). [CrossRef] [PubMed]

], where erbium fibers served as both 3-level lasers and 2-level saturable absorbers. Since the cross sections, σa and σe, of erbium are comparable, techniques of photon density enhancement in the SAQS fibers, such as double-passing routes and mismatch of mode field areas (MFA), were developed to activate SAQSing functions. Due to lifetime matching, τa2 = τg2, in a self-Q-switched laser, a saturable-amplifier pump switch (SAPS) was introduced for acquiring sequentially Q-switched pulses [16

16. T.-Y. Tsai, Y.-C. Fang, Z.-C. Lee, and H.-X. Tsao, “All-fiber passively Q-switched erbium laser using mismatch of mode field areas and a saturable-amplifier pump switch,” Opt. Lett. 34(19), 2891–2893 ( 2009). [CrossRef] [PubMed]

]. The function of the SAPS was to passively switch the pump intensity and delay the recovery of the gain population after Q-switched pulses. Although a passively Q-switched, all-fiber laser was demonstrated at low repetition rates, the peak pulse power decreased quickly (i.e. less pulse energy and larger pulse width) with an increasing pump power. The peak pulse power was 100 W at the lowest repetition rate of 250 Hz and decreased to 20 W at 1 kHz (i.e. ~10/τ2). The low-rate Q-switching was primarily due to the long relaxation lifetime of erbium (10 ms). Techniques shortening the relaxation lifetime of the erbium SAQS fiber could solve this inherent drawback and broaden the applications of the device.

2. Experiments

Figure 1
Fig. 1 Schematic diagram of a self-Q-switched, all-fiber erbium laser at 1530 nm with a tunable repetition rate using an auxiliary 1570 nm laser.
shows the schematic design of a self-Q-switched, erbium, all-fiber laser, pumped with a continuous-wave (CW) 980-nm laser diode (LD). The Q-switched laser was stabilized, and the pulse repetition rate was tunable using a 1570-nm laser that was also an erbium fiber laser pumped with a 980-nm LD (not shown). Therefore, the laser system could be simplified using only one high-power pump LD and a pump splitter with a properly designed ratio. The gain medium was a 210-cm erbium-doped fiber with a core diameter of 14 μm and an absorption loss of 19 dB⋅m−1 at 1530 nm, manufactured by the company Coractive. The SAQS was a 20-cm Er fiber, made by the manufacturer nLight, with a relatively smaller core diameter of 4 μm and an absorption loss of 110 dB⋅m−1 at 1530 nm. The mismatch of the mode field areas (MFA) between the gain and the SAQS resulted in high photon density and fast absorption saturation in the SAQS fiber, thereby giving rise to Q-switching action. The numerical aperture (NA) number and the mode field diameter of the SAQS were 0.2 and 6.5 μm, indicating a confinement factor Γ of about 0.53. Thus, the saturation power, Is,1570, was determined by Eq. (1) to be 1.2 mW. The 980/1530 nm WDM inside the resonator was used to protect the SAQS from the pump power. Similarly, a 1530/1570 nm WDM was employed to prevent the gain fiber from being stimulated by the 1570-nm laser. All components were core-fusion spliced. The length of the resonator was about 4 meters.

When the 1570-nm laser was turned on, the Q-switching performance was much improved. By comparing the two cases (i.e. with and without Ia,1570) at the same Rpr in Fig. 2(a), the improved pulse energy with the Ia,1570 demonstrates faster and more extensive recovery of Na,1530. Due to this increased Na,1530 recovery, a higher pump power was required with the Ia,1570. Furthermore, the improved recovery of Na,1530 denoted a higher hold-off ratio of the gain population in the gain fiber, in turn leading to a better Q-switching performance with a shorter pulse width and higher peak power as clearly demonstrated in Fig. 2(b).

We further improved the Q-switching performance by doubling the length of a SAQS fiber. The SAQS had an absorption loss of 44 dB at 1530 nm that was even larger than that of the gain fiber. Thus, the laser could not reach the threshold by pumping alone without the assistant of the Ia,1570. Stable, sequential, Q-switched pulses were achieved using a 10-mW Ia,1570, as shown in Fig. 4
Fig. 4 (a) Q-switching performance using a 10-mW Ia,1570 and a SAQS erbium fiber with an absorption loss of 44 dB at 1530nm. (b) Sequential Q-switched pulses at 1.5 kHz captured on an oscilloscope, and (c) the corresponding pulse with a peak power of 105 W.
. The pulse had a stable shape, a FWHM of about 40 ns, and a peak power of larger than 100 W along the pump range from 75 to 200 mW. The maximum pulse energy of 6 μJ and peak power of 165 W was achieved at the lowest Rpr of 0.1 kHz. The Rpr was proportional to the pump power and limited by the maximum 980-nm LD output. The high Q-switching efficiency was attributed to the high hold-off ratio of the gain population by the large Nai, which, in turn, lead to a high extraction efficiency of the pumped gain. By recording the readings on the oscilloscope, statistics showed that the deviation of the repetition rate, ΔRrp/Rrp was about 7% - 8% and the deviation of the peak power was about 8%. The stability showed no strong relation with Rrp, although it seemed that the stability was a little better (smaller ΔRrp/Rrp) when Rrp was higher. Since more pumping time was needed for the large gain population, the Q-switching was stabilized into a low-Rpr range from 0.1 to 1.5 kHz. Efficient Q-switching at higher Rpr should be achievable using a more intense pump LD. The results demonstrated here were better and more stable than what could be achieved using a saturable-amplifier pump switch [16

16. T.-Y. Tsai, Y.-C. Fang, Z.-C. Lee, and H.-X. Tsao, “All-fiber passively Q-switched erbium laser using mismatch of mode field areas and a saturable-amplifier pump switch,” Opt. Lett. 34(19), 2891–2893 ( 2009). [CrossRef] [PubMed]

].

3.Conclusion

We have demonstrated a self-Q-switched, all-fiber erbium laser emitting at 1530 nm through the use of an auxiliary laser at 1570 nm, Ia,1570, that allowed tunable and optimizable Q-switching performance. The Ia,1570 was applied to a SAQS erbium fiber to shorten the relaxation lifetime. The wavelengths of 1530 and 1570 nm are in the same band of energy transition between 4I13/2 and 4I15/2. A SAQS fiber with a 22-dB absorption loss was employed for demonstrating the effect of lifetime shortening, and the improvement on Q-switching at the repetition rate from 0.9 to 10 kHz. By doubling the length of the SAQS fiber and applying a 10-mW Ia,1570, sequential pulses with pulse energy of 6-4 μJ, steady pulse width of 38-40 ns and peak power of 165-105 W were achieved at repetition rate of 0.1-1.5 kHz. Efficient Q-switching at higher repetition rates is expected when a more intense pump source is employed.

References and links

1.

N. A. Russo, R. Duchowicz, J. Mora, J. L. Cruz, and M. V. Andrés, “High-efficiency Q-switched erbium fiber laser using a Bragg grating-based modulator,” Opt. Commun. 210(3-6), 361–366 ( 2002). [CrossRef]

2.

D. W. Huang, W. F. Liu, and C. C. Yang, “Q-switched all-fiber laser with an acoustically modulated fiber attenuator,” IEEE Photon. Technol. Lett. 12(9), 1153–1155 ( 2000). [CrossRef]

3.

D. Zalvidea, N. A. Russo, R. Duchowicz, M. Delgado-Pinar, A. Díez, J. L. Cruz, and M. V. Andrés, “High repetition rate acoustic-induced Q-switched all-fiber laser,” Opt. Commun. 244(1-6), 315–319 ( 2005). [CrossRef]

4.

M. Delgado-Pinar, D. Zalvidea, A. Díez, P. Pérez-Millan, and M. V. Andrés, “Q-switching of an all-fiber laser by acousto-optic modulation of a fiber Bragg grating,” Opt. Express 14(3), 1106–1112 ( 2006). [CrossRef] [PubMed]

5.

P. Pérez-Millán, A. Díez, M. V. Andrés, D. Zalvidea, and R. Duchowicz, “Q-switched all-fiber laser based on magnetostriction modulation of a Bragg grating,” Opt. Express 13(13), 5046–5051 ( 2005). [CrossRef] [PubMed]

6.

R. Paschotta, R. Häring, E. Gini, H. Melchior, U. Keller, H. L. Offerhaus, and D. J. Richardson, “Passively Q-switched 0.1-mJ fiber laser system at 1.53 mum,” Opt. Lett. 24(6), 388–390 ( 1999). [CrossRef] [PubMed]

7.

S. Kivistö, R. Koskinen, J. Paajaste, S. D. Jackson, M. Guina, and O. G. Okhotnikov, “Passively Q-switched Tm3+, Ho3+-doped silica fiber laser using a highly nonlinear saturable absorber and dynamic gain pulse compression,” Opt. Express 16(26), 22058–22063 ( 2008). [CrossRef] [PubMed]

8.

V. V. Dvoyrin, V. M. Mashinsky, and E. M. Dianov, “Yb-Bi pulsed fiber lasers,” Opt. Lett. 32(5), 451–453 ( 2007). [CrossRef] [PubMed]

9.

A. A. Fotiadi, A. S. Kurkov, and I. M. Razdobreev, “All-fiber passively Q-switched Ytterbium laser,” 2005 Conference on Lasers and Electro-Optics Europe, p. 515.

10.

P. Adel, M. Auerbach, C. Fallnich, S. Unger, H.-R. Müller, and J. Kirchhof, “Passive Q-switching by Tm3+co-doping of a Yb3+-fiber laser,” Opt. Express 11(21), 2730–2735 ( 2003). [CrossRef] [PubMed]

11.

A. S. Kurkov, E. M. Sholokhov, and O. I. Medvedkov, “All fiber Yb-Ho pulsed laser,” Laser Phys. Lett. 6(2), 135–138 ( 2009). [CrossRef]

12.

S. D. Jackson, “Passively Q-switched Tm(3+)-doped silica fiber lasers,” Appl. Opt. 46(16), 3311–3317 ( 2007). [CrossRef] [PubMed]

13.

R. D. Stultz, M. B. Camargo, and M. Birnbaum, “Passive Q-switch at 1.53 µm using divalent uranium ions in calcium fluoride,” J. Appl. Phys. 78(5), 2959–2961 ( 1995). [CrossRef]

14.

T.-Y. Tsai and M. Birnbaum, “Co2+:ZnS and Co2+:ZnSe Saturable Absorber Q-switches,” J. Appl. Phys. 87(1), 25–29 ( 2000). [CrossRef]

15.

T.-Y. Tsai and Y.-C. Fang, “A saturable absorber Q-switched all-fiber ring laser,” Opt. Express 17(3), 1429–1434 ( 2009). [CrossRef] [PubMed]

16.

T.-Y. Tsai, Y.-C. Fang, Z.-C. Lee, and H.-X. Tsao, “All-fiber passively Q-switched erbium laser using mismatch of mode field areas and a saturable-amplifier pump switch,” Opt. Lett. 34(19), 2891–2893 ( 2009). [CrossRef] [PubMed]

OCIS Codes
(060.2310) Fiber optics and optical communications : Fiber optics
(140.3510) Lasers and laser optics : Lasers, fiber
(140.3540) Lasers and laser optics : Lasers, Q-switched

ToC Category:
Lasers and Laser Optics

History
Original Manuscript: October 7, 2009
Revised Manuscript: November 2, 2009
Manuscript Accepted: November 8, 2009
Published: November 11, 2009

Citation
Tzong-Yow Tsai and Yen-Cheng Fang, "A self-Q-switched all-fiber erbium laser at 1530 nm using an auxiliary 1570-nm erbium laser," Opt. Express 17, 21628-21633 (2009)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-24-21628


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. N. A. Russo, R. Duchowicz, J. Mora, J. L. Cruz, and M. V. Andrés, “High-efficiency Q-switched erbium fiber laser using a Bragg grating-based modulator,” Opt. Commun. 210(3-6), 361–366 (2002). [CrossRef]
  2. D. W. Huang, W. F. Liu, and C. C. Yang, “Q-switched all-fiber laser with an acoustically modulated fiber attenuator,” IEEE Photon. Technol. Lett. 12(9), 1153–1155 (2000). [CrossRef]
  3. D. Zalvidea, N. A. Russo, R. Duchowicz, M. Delgado-Pinar, A. Díez, J. L. Cruz, and M. V. Andrés, “High repetition rate acoustic-induced Q-switched all-fiber laser,” Opt. Commun. 244(1-6), 315–319 (2005). [CrossRef]
  4. M. Delgado-Pinar, D. Zalvidea, A. Díez, P. Pérez-Millan, and M. V. Andrés, “Q-switching of an all-fiber laser by acousto-optic modulation of a fiber Bragg grating,” Opt. Express 14(3), 1106–1112 (2006). [CrossRef] [PubMed]
  5. P. Pérez-Millán, A. Díez, M. V. Andrés, D. Zalvidea, and R. Duchowicz, “Q-switched all-fiber laser based on magnetostriction modulation of a Bragg grating,” Opt. Express 13(13), 5046–5051 (2005). [CrossRef] [PubMed]
  6. R. Paschotta, R. Häring, E. Gini, H. Melchior, U. Keller, H. L. Offerhaus, and D. J. Richardson, “Passively Q-switched 0.1-mJ fiber laser system at 1.53 mum,” Opt. Lett. 24(6), 388–390 (1999). [CrossRef] [PubMed]
  7. S. Kivistö, R. Koskinen, J. Paajaste, S. D. Jackson, M. Guina, and O. G. Okhotnikov, “Passively Q-switched Tm3+, Ho3+-doped silica fiber laser using a highly nonlinear saturable absorber and dynamic gain pulse compression,” Opt. Express 16(26), 22058–22063 (2008). [CrossRef] [PubMed]
  8. V. V. Dvoyrin, V. M. Mashinsky, and E. M. Dianov, “Yb-Bi pulsed fiber lasers,” Opt. Lett. 32(5), 451–453 (2007). [CrossRef] [PubMed]
  9. A. A. Fotiadi, A. S. Kurkov, and I. M. Razdobreev, “All-fiber passively Q-switched Ytterbium laser,” 2005 Conference on Lasers and Electro-Optics Europe, p. 515.
  10. P. Adel, M. Auerbach, C. Fallnich, S. Unger, H.-R. Müller, and J. Kirchhof, “Passive Q-switching by Tm3+co-doping of a Yb3+-fiber laser,” Opt. Express 11(21), 2730–2735 (2003). [CrossRef] [PubMed]
  11. A. S. Kurkov, E. M. Sholokhov, and O. I. Medvedkov, “All fiber Yb-Ho pulsed laser,” Laser Phys. Lett. 6(2), 135–138 (2009). [CrossRef]
  12. S. D. Jackson, “Passively Q-switched Tm(3+)-doped silica fiber lasers,” Appl. Opt. 46(16), 3311–3317 (2007). [CrossRef] [PubMed]
  13. R. D. Stultz, M. B. Camargo, and M. Birnbaum, “Passive Q-switch at 1.53 µm using divalent uranium ions in calcium fluoride,” J. Appl. Phys. 78(5), 2959–2961 (1995). [CrossRef]
  14. T.-Y. Tsai and M. Birnbaum, “Co2+:ZnS and Co2+:ZnSe Saturable Absorber Q-switches,” J. Appl. Phys. 87(1), 25–29 (2000). [CrossRef]
  15. T.-Y. Tsai and Y.-C. Fang, “A saturable absorber Q-switched all-fiber ring laser,” Opt. Express 17(3), 1429–1434 (2009). [CrossRef] [PubMed]
  16. T.-Y. Tsai, Y.-C. Fang, Z.-C. Lee, and H.-X. Tsao, “All-fiber passively Q-switched erbium laser using mismatch of mode field areas and a saturable-amplifier pump switch,” Opt. Lett. 34(19), 2891–2893 (2009). [CrossRef] [PubMed]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1 Fig. 2 Fig. 3
 
Fig. 4
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited