OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 17, Iss. 25 — Dec. 7, 2009
  • pp: 22393–22400
« Show journal navigation

Fabrication and characterization of chalcogenide glass photonic crystal waveguides

Keijiro Suzuki, Yohei Hamachi, and Toshihiko Baba  »View Author Affiliations


Optics Express, Vol. 17, Issue 25, pp. 22393-22400 (2009)
http://dx.doi.org/10.1364/OE.17.022393


View Full Text Article

Acrobat PDF (283 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We report on the fabrication of chalcogenide glass (Ag-As2Se3) photonic crystal waveguides and the first detailed characterization of the linear and nonlinear optical properties. The waveguides, fabricated by e-beam lithography and ICP etching exhibit typical transmission spectra of photonic crystal waveguides, and exhibit high optical nonlinearity. Nonlinear phase shift of 1.5π through self-phase modulation is observed at 0.78 W input peak power in a 400 μm long device. The effective nonlinear parameter γeff estimated from this result reaches 2.6 × 104 W−1m−1. Four-wave mixing is also observed in the waveguide, while two-photon absorption at optical communication wavelengths is sufficiently small and the corresponding figure of merit is larger than 11.

© 2009 OSA

1. Introduction

Chalcogenide glasses (ChGs) are based on chalcogen elements (S, Se and Te), mixed with other elements such as As, Ge, P and Sb. They are transparent at optical communication wavelengths, and exhibit high optical Kerr nonlinearity as well as low two-photon absorption (TPA) [1

1. J. M. Harbold, F. O. Ilday, F. W. Wise, J. S. Sanghera, V. Q. Nguyen, L. B. Shaw, and I. D. Aggarwal, “Highly nonlinear As-S-Se glasses for all-optical switching,” Opt. Lett. 27(2), 119–121 ( 2002). [CrossRef] [PubMed]

,2

2. A. Zakery and S. R. Elliott, “Optical properties and applications of chalcogenide glasses: a review,” J. Non-Cryst. Solids 330(1-3), 1–12 ( 2003). [CrossRef]

]. The nonlinearity is non-resonant, and has a subpicosecond response time. ChGs also exhibit several photoinduced phenomena when illuminated with light near the band-gap. By the use of these phenomena, the formation of waveguides and gratings [3

3. A. V. Rode, A. Zakery, M. Samoc, R. B. Charters, E. G. Gamaly, and B. Luther-Davies, “Laser-deposited As2S3 chalcogenide films for waveguide applications,” Appl. Surf. Sci. 197-198, 481–485 ( 2002). [CrossRef]

,4

4. T. G. Robinson, R. G. DeCorby, J. N. McMullin, C. J. Haugen, S. O. Kasap, and D. Tonchev, “Strong Bragg gratings photoinduced by 633-nm illumination in evaporated As2Se3 thin films,” Opt. Lett. 28(6), 459–461 ( 2003). [CrossRef] [PubMed]

] and post-tuning of photonic crystal waveguides [5

5. D. Freeman, C. Grillet, M. W. Lee, C. L. C. Smith, Y. Ruan, A. Rode, M. Krolikowska, S. Tomljenovic-Hanic, C. M. De Sterke, M. J. Steel, B. Luther-Davies, S. Madden, D. J. Moss, Y. H. Lee, and B. J. Eggleton, “Chalcogenide glass photonic crystals,” Photon. Nanostructures 6, 3–11 ( 2008). [CrossRef]

] have been reported. In addition, integration with Si-photonics is also possible because ChGs can be formed and processed at low temperature (<400 °C). These characteristics make ChGs a promising platform for integrated all-optical devices [6

6. V. G. Ta’eed, N. J. Baker, L. B. Fu, K. Finsterbusch, M. R. E. Lamont, D. J. Moss, H. C. Nguyen, B. J. Eggleton, D. Y. Choi, S. Madden, and B. Luther-Davies, “Ultrafast all-optical chalcogenide glass photonic circuits,” Opt. Express 15(15), 9205–9221 ( 2007), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-15-15-9205. [CrossRef] [PubMed]

]. Recently, it is found that Ag-doped As2Se3 glass (i.e., Agx(As0.4Se0.6)100- x) has particularly high Kerr nonlinearity higher than As2Se3 by around 2−4 times at wavelength λ = 1053 nm without increasing TPA coefficient [7

7. K. Ogusu, J. Yamasaki, S. Maeda, M. Kitao, and M. Minakata, “Linear and nonlinear optical properties of Ag-As-Se chalcogenide glasses for all-optical switching,” Opt. Lett. 29(3), 265–267 ( 2004). [CrossRef] [PubMed]

], and low material absorption loss at infrared region [8

8. K. Suzuki, K. Ogusu, and M. Minakata, “Single-mode Ag-As2Se3 strip-loaded waveguides for applications to all-optical devices,” Opt. Express 13(21), 8634–8641 ( 2005), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-13-21-8634. [CrossRef] [PubMed]

]. We apply this glass in a guiding layer of our devices described below.

Further nonlinear enhancement is expected for the combination of the ChGs and PCWs. However, the difficulty in the fabrication has limited its experimental demonstration [5

5. D. Freeman, C. Grillet, M. W. Lee, C. L. C. Smith, Y. Ruan, A. Rode, M. Krolikowska, S. Tomljenovic-Hanic, C. M. De Sterke, M. J. Steel, B. Luther-Davies, S. Madden, D. J. Moss, Y. H. Lee, and B. J. Eggleton, “Chalcogenide glass photonic crystals,” Photon. Nanostructures 6, 3–11 ( 2008). [CrossRef]

]. ChGs are much softer than Si, which makes difficult to obtain vertical sidewalls of air-holes and clean facets for efficient optical coupling to the waveguides. Hence, only their fundamental characteristics have been investigated under the limited condition [16

16. M. W. Lee, C. Grillet, C. G. Poulton, C. Monat, C. L. Smith, E. Mägi, D. Freeman, S. Madden, B. Luther-Davies, and B. J. Eggleton, “Characterizing photonic crystal waveguides with an expanded k-space evanescent coupling technique,” Opt. Express 16(18), 13800–13808 ( 2008), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-16-18-13800. [CrossRef] [PubMed]

], and their nonlinear characteristics have not been investigated yet.

In this study, we develop the fabrication technique of fine Ag-As2Se3 ChG PCW using e-beam lithography and ICP etching, and characterize their detailed linear and nonlinear optical properties, for the first time. We successfully observed the light propagation characteristics of the waveguides. In addition, we confirmed the generation of SPM and the four-wave mixing (FWM) in the ChG PCW. Negligible TPA is also observed at optical communication wavelengths.

2. Design and fabrication

Figure 1(a)
Fig. 1 (a) Schematic of chalcogenide glass photonic crystal waveguide. (b) Band diagram of Ag-As2Se3 photonic crystal waveguide. (c) Magnified figure of (b).
shows the schematic of ChG PCW, which consists of air-holes embedded in a Ag-As2Se3 layer. An InP substrate is used for easy cleavage. A Ti layer is used for better adhesion between As2Se3 and InP. Typical device length is 400 μm. To analyze waveguide modes, we used 3D-FDTD method. In this analysis, we assumed that refractive index of the slab is 2.85, the normalized air-hole diameter 2r/a is 0.52 and normalized slab thickness d/a is 0.63, where a is the lattice constant. Figures 1(b) and 1(c) show the three-dimensional photonic band diagram, which show the presence of guiding modes within the bandgap. Provided the light propagation at λ = 1550 nm, we obtain a = 480 nm, 2r = 250 nm and d = 300 nm. These structural parameters indicate that the fabrication of ChG PCW is practical. The transmission bandwidth of even guided mode sandwiched by the air light cone and the band-edge completely covers the C band of silica fiber communications.

Figure 2
Fig. 2 Fabrication process of the Ag-As2Se3 chalcogenide glass photonic crystal waveguides. (a) Ti thermal evaporation. (b) As2Se3 thermal evaporation. (c) Ag thermal evaporation. (d) Photo-doping of Ag into As2Se3 using Halogen lamp. (e) EB writing of photonic crystal waveguides. (f) ICP etching using a CHF3/CF4 gas mixture. (g) EB resist removal using ZDMAC remover. (h) Wet-etching in HF and HCl solution.
shows a fabrication process of ChG PCW. First, Ti layer is thermally evaporated onto an InP substrate by 10 nm at 6.0 nm/min. Then, commercially available As2Se3, Furuuchi Chemical is thermally evaporated onto the Ti layer by 300 nm at a rate of 10 nm/min. The Ag-As2Se3 layer cannot be obtained by direct evaporation of the ternary Ag-As-Se glass because of their phase difference. Therefore, Ag layer is evaporated on the As2Se3 layer by 10 nm, and doped into As2Se3 film using photodoping technique [17

17. T. Wagner, V. Perina, A. Mackova, E. Rauhala, A. Seppala, M. Vleck, S. O. Kasap, M. Vlcek, and M. Frumar, “The tailoring of the composition of Ag-As-S amorphous films using photo-induced solid state reaction between Ag and As30S70 films,” Solid State Ion. 141-142(1), 387–395 ( 2001). [CrossRef]

]. 10 nm thickness of Ag corresponds to an Ag content of 5 at.%. Next, standard e-beam lithography is used to pattern PCWs. An EB resist ZEP-520A, ZEON is spincasted onto the surface, and prebaked at 180 °C for 2 min. PCWs are patterned by e-beam accelerated by 50 kV. After development, the substrate is post-baked at 130 °C for 30 min. The pattern of PCW is transferred to Ag-As2Se3 layer by ICP etching (RIE-10iP, Samco). The etching gas is a CHF3 and CF4 mixture. After the etching, a residual EB resist on the surface of the guiding layer is removed by a cleaner solution. Finally, Ti and InP underneath the PCWs are removed by HF and successive HCl solution to form an air-bridge structure.

Figure 3
Fig. 3 SEM image of a fabricated Ag-As2Se3 photonic crystal waveguide. (a) Cross-sectional view. (b) Top view.
shows scanning electron microscope (SEM) image of the fabricated ChG PCW. The cross-sectional image shows that the air-holes have sufficiently smooth and vertical sidewalls, and the cleaved facet looks clean enough to couple external light to the waveguide efficiently. From the top view, it is evaluated that the fluctuation of air-hole diameter is ± 10 nm.

3. Measurement

3.1 Transmission spectrum

Figure 4
Fig. 4 Transmission spectrum of a fabricated chalcogenide glass photonic crystal waveguide.
shows the transmission spectrum of a fabricated ChG PCW. Here, tunable laser light was coupled to the waveguide from the cleaved facet through microscope objectives. Transmission drops caused by the light line and band edge are confirmed, indicating that the obtained spectrum is a typical one of single line defect PCW. The transmission bandwidth defined by the light line and band edge is in good agreement with photonic band analysis shown in Fig. 1(c). The transmitted power is ~5 dB lower than the typical one of our 400-μm-long Si-PCW at λ = 1550 nm (corresponding to group index ng ~5). In our Si-PCW, the propagation loss is typical 1 dB/mm, corresponding to 0.4 dB loss in a 400-μm-length waveguide. In the ChG PCW, the loss of 400-μm-length waveguide is estimated to 5 + 0.4 = 5.4 dB. Hence, 5.4 dB/0.4 mm = 13.5 dB/mm is evaluated as the propagation loss of the ChG PCW.

3.2 Self-phase modulation

We observed SPM by launching optical pulses in the transmission band near the band-edge. In the SPM and TPA measurements, we used another sample which has a band-edge at λ ~1550 nm. Figure 5
Fig. 5 Experimental setup for self-phase modulation.
shows experimental setup. The optical pulse from passive mode-locked laser was expanded spectrally by SPM at the first erbium-doped fiber amplifier (EDFA). Then, the pulse was filtered at desired center wavelength λp and pulse width τp. We chose λp = 1547 nm corresponding to the band edge of the sample (ng = 10), and τp = 2.0 ps to suppress SPM in silica fibers of the setup. The filtered pulse was amplified by the second EDFA, and coupled to the PCW through the microscope objectives. The output pulse from the PCW was detected with a lensed fiber. The pulse spectrum was observed by an optical spectrum analyzer (OSA).

Figure 6
Fig. 6 Spectra of output pulse exhibiting SPM. Each spectrum is normalized to the peak magnitude
shows spectra of output pulse at different launched input peak powers P in for 400-μm-long device. The SPM-induced spread spectrum is clearly observed when the coupled pulse peak power is higher than 0.63 W. The asymmetrical spreading of the spectra is caused by the cut-off at the band-edge. When we coupled pulses of P in = 0.78 W to the PCW, the output pulse spectrum exhibited two peaks and center dip, indicating that the nonlinear phase change ΔϕNL = 1.5π [18

18. G. P. Agrawal, Nonlinear Fiber Optics, Fourth ed. (Academic Press, London, 2007).

]. This is the evidence of the large nonlinear enhancement of the ChG.

Let us compare the efficiency of the nonlinear phase change with Si-wire [19

19. E. Dulkeith, Y. A. Vlasov, X. Chen, N. C. Panoiu, and R. M. Osgood Jr., “Self-phase-modulation in submicron silicon-on-insulator photonic wires,” Opt. Express 14(12), 5524–5534 ( 2006), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-14-12-5524. [CrossRef] [PubMed]

]. The Ag-As2Se3 PCW requires 0.78 W input peak power, 230 μm effective length L eff (1/e power decay length for a propagation loss of 13.5 dB/mm, neglecting TPA) and 0.18 μm2 cross-sectional area for 1.5π nonlinear phase shift. On the other hand, in Si-wire, the same phase shift is observed with 6.85 W peak power, 3400 μm effective length (propagation loss: 0.36 dB/mm) and 0.106 μm2 cross-sectional area. That is, the Ag-As2Se3 PCW only needs nine times lower peak power, and 15 times shorter effective length and 1.7 times broader cross-sectional area. In total, it is 79 times more efficient than Si-wire.

To confirm the result, we also estimate the efficiency from material and structural parameters. Although the nonlinear refractive index n 2 of Ag-As2Se3 has not been measured at λ ~1550 nm, it has been reported in [7

7. K. Ogusu, J. Yamasaki, S. Maeda, M. Kitao, and M. Minakata, “Linear and nonlinear optical properties of Ag-As-Se chalcogenide glasses for all-optical switching,” Opt. Lett. 29(3), 265–267 ( 2004). [CrossRef] [PubMed]

] that the Ag doping enhances n 2 to 2 − 4 times larger at λ = 1053 nm. Let us assume here that n 2 of Ag-As2Se3 is three times larger than 2300 × 10−20 m2/W for As2Se3 [20

20. J. M. Harbold, F. Ö. Ilday, F. W. Wise, J. S. Sanghera, V. Q. Nguyen, L. B. Shaw, and I. D. Aggarwal, “Highly nonlinear As-S-Se glasses for all-optical switching,” Opt. Lett. 27(2), 119–121 ( 2002). [CrossRef] [PubMed]

], i.e. 6900 × 10−20 m2/W, which is 26 times Si’s (270 × 10−20 m2/W) [21

21. R. W. Boyd, Nonlinear Optics, Third ed. (Academic Press, New York, 2008).

]. The nonlinear enhancement is proportional to n g 2 [10

10. Y. Hamachi, S. Kubo, and T. Baba, “Slow light with low dispersion and nonlinear enhancement in a lattice-shifted photonic crystal waveguide,” Opt. Lett. 34(7), 1072–1074 ( 2009). [CrossRef] [PubMed]

,14

14. K. Inoue, H. Oda, N. Ikeda, and K. Asakawa, “Enhanced third-order nonlinear effects in slow-light photonic-crystal slab waveguides of line-defect,” Opt. Express 17(9), 7206–7216 ( 2009), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-9-7206. [CrossRef] [PubMed]

]. Since n g of the fabricated PCW and Si-wire are estimated to be 10 and 4.5, respectively, the enhancement is (10/4.5)2 = 5 times. Regarding the cross-sectional area, it is the same as mentioned above. In total, the fabricated PCW should be more efficient than Si-wire by 26 × 5/1.7 = 76 times. This value is in good agreement with the experimental value.

In the same manner, we estimated the effective nonlinear parameter γeff = ΔϕNL/P in L eff to be 2.6 × 104 W−1m−1. This value is much larger than a reported value for As2S3 ChG rib-waveguide of 10 W−1m−1 [22

22. M. R. Lamont, B. Luther-Davies, D.-Y. Choi, S. Madden, X. Gai, and B. J. Eggleton, “Net-gain from a parametric amplifier on a chalcogenide optical chip,” Opt. Express 16(25), 20374–20381 ( 2008), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-16-25-20374. [CrossRef] [PubMed]

]. The above n 2 for Ag-As2Se3 is already 23 times larger than 300 × 10−20 W−1m−1 for As2S3. Since ng of the Ag-As2Se3 PCW and As2S3 rib-waveguide are estimated to 10 and 2.4, respectively, the enhancement is (10/2.4)2 = 17 times. As for A eff, we assumed that it is proportional to the cross-sectional area of the waveguide, i.e., 0.18 and 1.2 μm2 for the PCW and rib-waveguide, respectively, corresponding to 7 times enhancement. In total, deduced γeff of the ChG PCW is 10 × 23 × 17 × 7 = 2.7 × 104 W−1m−1. This also agrees well with the above value. Thus, all the comparisons are consistent with each other.

3.3 Two-photon absorption

We measured input/output characteristics of a ChG PCW to evaluate the TPA. The experiment setup was the same as for the SPM. Figure 7
Fig. 7 Output average power versus input peak power characteristic.
shows the result. Note that the output power keeps linear when the input power is sufficiently high to generate the SPM, indicating that the TPA of Ag-As2Se3 is negligible in the optical communication wavelengths.

Nonlinear switching devices are designed to have a large figure of merit (FOM), which is defined as the nonlinearity per unit nonlinear absorption (i.e. FOM = n 2/(βλ), where β is the TPA coefficient). The requirement for FOM depends on switching mechanisms, e.g. ~5 for Mach-Zehnder switches [23

23. G. Lenz, J. Zimmermann, T. Katsufuji, M. E. Lines, H. Y. Hwang, S. Spälter, R. E. Slusher, S. W. Cheong, J. S. Sanghera, and I. D. Aggarwal, “Large Kerr effect in bulk Se-based chalcogenide glasses,” Opt. Lett. 25(4), 254–256 ( 2000). [CrossRef] [PubMed]

]. In bulk As2Se3, FOM is as high as ~11 [1

1. J. M. Harbold, F. O. Ilday, F. W. Wise, J. S. Sanghera, V. Q. Nguyen, L. B. Shaw, and I. D. Aggarwal, “Highly nonlinear As-S-Se glasses for all-optical switching,” Opt. Lett. 27(2), 119–121 ( 2002). [CrossRef] [PubMed]

]. Ag-doped As2Se3 exhibits not only high nonlinearity but negligible TPA. As the nonlinearity of Ag-As2Se3 is higher than As2Se3 by Ag doping, FOM > 11 is expected.

3.4 Four-wave mixing

Figure 8
Fig. 8 Experimental setup for FWM.
shows the experimental setup. We launched two optical pulses at different wavelengths as pump lights to generate FWM. The mode-locked laser pulse was expanded spectrally at the first EDFA, then divided by 3 dB coupler into two arms. The divided pulses were filtered at each band-pass filters as pump lights. The center wavelengths of the two pulses λ11) and λ22) were 1556 nm (192.7 THz) and 1560 nm (192.2 THz), respectively, both corresponding to the fast group velocity regime of the PCW. Their spectral width was suppressed to less than 2 nm to avoid the FWM in silica fibers of the setup. Then, they were amplified by following EDFA. A delay line was introduced into one arm to alter the timing of the confluence at a following 3 dB coupler. The timing of the two pulses was adjusted so that their auto-correlation trace exhibits the clearest beat. The pulses were coupled to the PCW through the microscope objectives. The output pulse was detected by a lensed fiber, and its spectrum was observed by the OSA.

Figure 9
Fig. 9 Spectra of output pulse exhibiting FWM in Ag-As2Se3 PCW.
shows spectra of the output pulse. Signal and idler light are observed around the two pumps when the input peak power increases. The center wavelengths of signal λsigsig) and idler λidlidl) light are 1552 (193.2 THz) nm and 1564 nm (191.7 THz), respectively, which is in good agreement with theoretically estimated values from frequency matching conditions (ωsig = 2ω1 − ω2, ωidl = 2ω2 − ω1). Considering the short device length (400 μm) and pulse propagation at the fast group velocity regime, this is another evidence of the large nonlinearity in the ChG.

In Si-wire [24

24. H. Fukuda, K. Yamada, T. Shoji, M. Takahashi, T. Tsuchizawa, T. Watanabe, J. Takahashi, and S. Itabashi, “Four-wave mixing in silicon wire waveguides,” Opt. Express 13(12), 4629–4637 ( 2005), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-13-12-4629. [CrossRef] [PubMed]

], the FWM occurs with 0.2 W peak power (CW), 10200 μm effective length (propagation loss: 0.24 dB/mm) and 0.09 μm2 cross-sectional area. In comparison with them, 1.7 times higher peak power, 1/44 times shorter effective length and a twice cross-sectional area give the similar FWM, corresponding to 13 times higher efficiency than Si-wire’s.

4. Conclusion

We have fabricated Ag-As2Se3 chalcogenide glass photonic crystal waveguides and demonstrated large self-phase modulation, and four-wave mixing, and negligible two-photon absorption for the first time. The large effective nonlinear parameter (2.6 × 104 W−1m−1) is the clear evidence of the advantage of chalcogenide glass photonic crystal waveguides for all-optical switching devices. Further nonlinearity enhancement is expected by exploiting low dispersion slow-light structures.

Acknowledgements

This work was supported from the JSPS Research Fellow-ships for Young Scientists.

References and links

1.

J. M. Harbold, F. O. Ilday, F. W. Wise, J. S. Sanghera, V. Q. Nguyen, L. B. Shaw, and I. D. Aggarwal, “Highly nonlinear As-S-Se glasses for all-optical switching,” Opt. Lett. 27(2), 119–121 ( 2002). [CrossRef] [PubMed]

2.

A. Zakery and S. R. Elliott, “Optical properties and applications of chalcogenide glasses: a review,” J. Non-Cryst. Solids 330(1-3), 1–12 ( 2003). [CrossRef]

3.

A. V. Rode, A. Zakery, M. Samoc, R. B. Charters, E. G. Gamaly, and B. Luther-Davies, “Laser-deposited As2S3 chalcogenide films for waveguide applications,” Appl. Surf. Sci. 197-198, 481–485 ( 2002). [CrossRef]

4.

T. G. Robinson, R. G. DeCorby, J. N. McMullin, C. J. Haugen, S. O. Kasap, and D. Tonchev, “Strong Bragg gratings photoinduced by 633-nm illumination in evaporated As2Se3 thin films,” Opt. Lett. 28(6), 459–461 ( 2003). [CrossRef] [PubMed]

5.

D. Freeman, C. Grillet, M. W. Lee, C. L. C. Smith, Y. Ruan, A. Rode, M. Krolikowska, S. Tomljenovic-Hanic, C. M. De Sterke, M. J. Steel, B. Luther-Davies, S. Madden, D. J. Moss, Y. H. Lee, and B. J. Eggleton, “Chalcogenide glass photonic crystals,” Photon. Nanostructures 6, 3–11 ( 2008). [CrossRef]

6.

V. G. Ta’eed, N. J. Baker, L. B. Fu, K. Finsterbusch, M. R. E. Lamont, D. J. Moss, H. C. Nguyen, B. J. Eggleton, D. Y. Choi, S. Madden, and B. Luther-Davies, “Ultrafast all-optical chalcogenide glass photonic circuits,” Opt. Express 15(15), 9205–9221 ( 2007), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-15-15-9205. [CrossRef] [PubMed]

7.

K. Ogusu, J. Yamasaki, S. Maeda, M. Kitao, and M. Minakata, “Linear and nonlinear optical properties of Ag-As-Se chalcogenide glasses for all-optical switching,” Opt. Lett. 29(3), 265–267 ( 2004). [CrossRef] [PubMed]

8.

K. Suzuki, K. Ogusu, and M. Minakata, “Single-mode Ag-As2Se3 strip-loaded waveguides for applications to all-optical devices,” Opt. Express 13(21), 8634–8641 ( 2005), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-13-21-8634. [CrossRef] [PubMed]

9.

T. Baba, “Slow light in photonic crystals,” Nat. Photonics 2(8), 465–473 ( 2008). [CrossRef]

10.

Y. Hamachi, S. Kubo, and T. Baba, “Slow light with low dispersion and nonlinear enhancement in a lattice-shifted photonic crystal waveguide,” Opt. Lett. 34(7), 1072–1074 ( 2009). [CrossRef] [PubMed]

11.

B. Corcoran, C. Monat, C. Grillet, D. J. Moss, B. J. Eggleton, T. P. White, L. O'Faolain, and T. F. Krauss, “Green light emission in silicon through slow-light enhanced third-harmonic generation in photonic-crystal waveguides,” Nat. Photonics 3(4), 206–210 ( 2009). [CrossRef]

12.

C. Monat, B. Corcoran, M. Ebnali-Heidari, C. Grillet, B. J. Eggleton, T. P. White, L. O’Faolain, and T. F. Krauss, “Slow light enhancement of nonlinear effects in silicon engineered photonic crystal waveguides,” Opt. Express 17(4), 2944–2953 ( 2009), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-4-2944. [CrossRef] [PubMed]

13.

A. Baron, A. Ryasnyanskiy, N. Dubreuil, P. Delaye, Q. Vy Tran, S. Combrié, A. de Rossi, R. Frey, and G. Roosen, “Light localization induced enhancement of third order nonlinearities in a GaAs photonic crystal waveguide,” Opt. Express 17(2), 552–557 ( 2009), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-2-552. [CrossRef] [PubMed]

14.

K. Inoue, H. Oda, N. Ikeda, and K. Asakawa, “Enhanced third-order nonlinear effects in slow-light photonic-crystal slab waveguides of line-defect,” Opt. Express 17(9), 7206–7216 ( 2009), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-9-7206. [CrossRef] [PubMed]

15.

D. Pudo, B. Corcoran, C. Monat, M. Pelusi, D. J. Moss, B. J. Eggleton, T. P. White, L. O'Faolain, and T. F. Krauss, “Investigation of slow light enhanced nonlinear transmission for all-optical regeneration in silicon photonic crystal waveguides at 10 Gbit/s,” Photonic. Nanostruct ,” Corrected Proof. In Press., doi:. [CrossRef]

16.

M. W. Lee, C. Grillet, C. G. Poulton, C. Monat, C. L. Smith, E. Mägi, D. Freeman, S. Madden, B. Luther-Davies, and B. J. Eggleton, “Characterizing photonic crystal waveguides with an expanded k-space evanescent coupling technique,” Opt. Express 16(18), 13800–13808 ( 2008), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-16-18-13800. [CrossRef] [PubMed]

17.

T. Wagner, V. Perina, A. Mackova, E. Rauhala, A. Seppala, M. Vleck, S. O. Kasap, M. Vlcek, and M. Frumar, “The tailoring of the composition of Ag-As-S amorphous films using photo-induced solid state reaction between Ag and As30S70 films,” Solid State Ion. 141-142(1), 387–395 ( 2001). [CrossRef]

18.

G. P. Agrawal, Nonlinear Fiber Optics, Fourth ed. (Academic Press, London, 2007).

19.

E. Dulkeith, Y. A. Vlasov, X. Chen, N. C. Panoiu, and R. M. Osgood Jr., “Self-phase-modulation in submicron silicon-on-insulator photonic wires,” Opt. Express 14(12), 5524–5534 ( 2006), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-14-12-5524. [CrossRef] [PubMed]

20.

J. M. Harbold, F. Ö. Ilday, F. W. Wise, J. S. Sanghera, V. Q. Nguyen, L. B. Shaw, and I. D. Aggarwal, “Highly nonlinear As-S-Se glasses for all-optical switching,” Opt. Lett. 27(2), 119–121 ( 2002). [CrossRef] [PubMed]

21.

R. W. Boyd, Nonlinear Optics, Third ed. (Academic Press, New York, 2008).

22.

M. R. Lamont, B. Luther-Davies, D.-Y. Choi, S. Madden, X. Gai, and B. J. Eggleton, “Net-gain from a parametric amplifier on a chalcogenide optical chip,” Opt. Express 16(25), 20374–20381 ( 2008), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-16-25-20374. [CrossRef] [PubMed]

23.

G. Lenz, J. Zimmermann, T. Katsufuji, M. E. Lines, H. Y. Hwang, S. Spälter, R. E. Slusher, S. W. Cheong, J. S. Sanghera, and I. D. Aggarwal, “Large Kerr effect in bulk Se-based chalcogenide glasses,” Opt. Lett. 25(4), 254–256 ( 2000). [CrossRef] [PubMed]

24.

H. Fukuda, K. Yamada, T. Shoji, M. Takahashi, T. Tsuchizawa, T. Watanabe, J. Takahashi, and S. Itabashi, “Four-wave mixing in silicon wire waveguides,” Opt. Express 13(12), 4629–4637 ( 2005), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-13-12-4629. [CrossRef] [PubMed]

OCIS Codes
(160.2750) Materials : Glass and other amorphous materials
(230.3120) Optical devices : Integrated optics devices
(230.4320) Optical devices : Nonlinear optical devices
(230.5298) Optical devices : Photonic crystals

ToC Category:
Photonic Crystals

History
Original Manuscript: October 2, 2009
Revised Manuscript: November 13, 2009
Manuscript Accepted: November 14, 2009
Published: November 23, 2009

Citation
Keijiro Suzuki, Yohei Hamachi, and Toshihiko Baba, "Fabrication and characterization of chalcogenide glass photonic crystal waveguides," Opt. Express 17, 22393-22400 (2009)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-25-22393


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. J. M. Harbold, F. O. Ilday, F. W. Wise, J. S. Sanghera, V. Q. Nguyen, L. B. Shaw, and I. D. Aggarwal, “Highly nonlinear As-S-Se glasses for all-optical switching,” Opt. Lett. 27(2), 119–121 (2002). [CrossRef] [PubMed]
  2. A. Zakery and S. R. Elliott, “Optical properties and applications of chalcogenide glasses: a review,” J. Non-Cryst. Solids 330(1-3), 1–12 (2003). [CrossRef]
  3. A. V. Rode, A. Zakery, M. Samoc, R. B. Charters, E. G. Gamaly, and B. Luther-Davies, “Laser-deposited As2S3 chalcogenide films for waveguide applications,” Appl. Surf. Sci. 197-198, 481–485 (2002). [CrossRef]
  4. T. G. Robinson, R. G. DeCorby, J. N. McMullin, C. J. Haugen, S. O. Kasap, and D. Tonchev, “Strong Bragg gratings photoinduced by 633-nm illumination in evaporated As2Se3 thin films,” Opt. Lett. 28(6), 459–461 (2003). [CrossRef] [PubMed]
  5. D. Freeman, C. Grillet, M. W. Lee, C. L. C. Smith, Y. Ruan, A. Rode, M. Krolikowska, S. Tomljenovic-Hanic, C. M. De Sterke, M. J. Steel, B. Luther-Davies, S. Madden, D. J. Moss, Y. H. Lee, and B. J. Eggleton, “Chalcogenide glass photonic crystals,” Photon. Nanostructures 6, 3–11 (2008). [CrossRef]
  6. V. G. Ta’eed, N. J. Baker, L. B. Fu, K. Finsterbusch, M. R. E. Lamont, D. J. Moss, H. C. Nguyen, B. J. Eggleton, D. Y. Choi, S. Madden, and B. Luther-Davies, “Ultrafast all-optical chalcogenide glass photonic circuits,” Opt. Express 15(15), 9205–9221 (2007), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-15-15-9205 . [CrossRef] [PubMed]
  7. K. Ogusu, J. Yamasaki, S. Maeda, M. Kitao, and M. Minakata, “Linear and nonlinear optical properties of Ag-As-Se chalcogenide glasses for all-optical switching,” Opt. Lett. 29(3), 265–267 (2004). [CrossRef] [PubMed]
  8. K. Suzuki, K. Ogusu, and M. Minakata, “Single-mode Ag-As2Se3 strip-loaded waveguides for applications to all-optical devices,” Opt. Express 13(21), 8634–8641 (2005), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-13-21-8634 . [CrossRef] [PubMed]
  9. T. Baba, “Slow light in photonic crystals,” Nat. Photonics 2(8), 465–473 (2008). [CrossRef]
  10. Y. Hamachi, S. Kubo, and T. Baba, “Slow light with low dispersion and nonlinear enhancement in a lattice-shifted photonic crystal waveguide,” Opt. Lett. 34(7), 1072–1074 (2009). [CrossRef] [PubMed]
  11. B. Corcoran, C. Monat, C. Grillet, D. J. Moss, B. J. Eggleton, T. P. White, L. O'Faolain, and T. F. Krauss, “Green light emission in silicon through slow-light enhanced third-harmonic generation in photonic-crystal waveguides,” Nat. Photonics 3(4), 206–210 (2009). [CrossRef]
  12. C. Monat, B. Corcoran, M. Ebnali-Heidari, C. Grillet, B. J. Eggleton, T. P. White, L. O’Faolain, and T. F. Krauss, “Slow light enhancement of nonlinear effects in silicon engineered photonic crystal waveguides,” Opt. Express 17(4), 2944–2953 (2009), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-4-2944 . [CrossRef] [PubMed]
  13. A. Baron, A. Ryasnyanskiy, N. Dubreuil, P. Delaye, Q. Vy Tran, S. Combrié, A. de Rossi, R. Frey, and G. Roosen, “Light localization induced enhancement of third order nonlinearities in a GaAs photonic crystal waveguide,” Opt. Express 17(2), 552–557 (2009), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-2-552 . [CrossRef] [PubMed]
  14. K. Inoue, H. Oda, N. Ikeda, and K. Asakawa, “Enhanced third-order nonlinear effects in slow-light photonic-crystal slab waveguides of line-defect,” Opt. Express 17(9), 7206–7216 (2009), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-9-7206 . [CrossRef] [PubMed]
  15. D. Pudo, B. Corcoran, C. Monat, M. Pelusi, D. J. Moss, B. J. Eggleton, T. P. White, L. O'Faolain, and T. F. Krauss, “Investigation of slow light enhanced nonlinear transmission for all-optical regeneration in silicon photonic crystal waveguides at 10 Gbit/s,” Photonic. Nanostruct ,” Corrected Proof. In Press., doi:. [CrossRef]
  16. M. W. Lee, C. Grillet, C. G. Poulton, C. Monat, C. L. Smith, E. Mägi, D. Freeman, S. Madden, B. Luther-Davies, and B. J. Eggleton, “Characterizing photonic crystal waveguides with an expanded k-space evanescent coupling technique,” Opt. Express 16(18), 13800–13808 (2008), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-16-18-13800 . [CrossRef] [PubMed]
  17. T. Wagner, V. Perina, A. Mackova, E. Rauhala, A. Seppala, M. Vleck, S. O. Kasap, M. Vlcek, and M. Frumar, “The tailoring of the composition of Ag-As-S amorphous films using photo-induced solid state reaction between Ag and As30S70 films,” Solid State Ion. 141-142(1), 387–395 (2001). [CrossRef]
  18. G. P. Agrawal, Nonlinear Fiber Optics, Fourth ed. (Academic Press, London, 2007).
  19. E. Dulkeith, Y. A. Vlasov, X. Chen, N. C. Panoiu, and R. M. Osgood., “Self-phase-modulation in submicron silicon-on-insulator photonic wires,” Opt. Express 14(12), 5524–5534 (2006), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-14-12-5524 . [CrossRef] [PubMed]
  20. J. M. Harbold, F. Ö. Ilday, F. W. Wise, J. S. Sanghera, V. Q. Nguyen, L. B. Shaw, and I. D. Aggarwal, “Highly nonlinear As-S-Se glasses for all-optical switching,” Opt. Lett. 27(2), 119–121 (2002). [CrossRef] [PubMed]
  21. R. W. Boyd, Nonlinear Optics, Third ed. (Academic Press, New York, 2008).
  22. M. R. Lamont, B. Luther-Davies, D.-Y. Choi, S. Madden, X. Gai, and B. J. Eggleton, “Net-gain from a parametric amplifier on a chalcogenide optical chip,” Opt. Express 16(25), 20374–20381 (2008), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-16-25-20374 . [CrossRef] [PubMed]
  23. G. Lenz, J. Zimmermann, T. Katsufuji, M. E. Lines, H. Y. Hwang, S. Spälter, R. E. Slusher, S. W. Cheong, J. S. Sanghera, and I. D. Aggarwal, “Large Kerr effect in bulk Se-based chalcogenide glasses,” Opt. Lett. 25(4), 254–256 (2000). [CrossRef] [PubMed]
  24. H. Fukuda, K. Yamada, T. Shoji, M. Takahashi, T. Tsuchizawa, T. Watanabe, J. Takahashi, and S. Itabashi, “Four-wave mixing in silicon wire waveguides,” Opt. Express 13(12), 4629–4637 (2005), http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-13-12-4629 . [CrossRef] [PubMed]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited