OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 17, Iss. 5 — Mar. 2, 2009
  • pp: 3424–3428
« Show journal navigation

Integrated polymer microprisms for free space optical beam deflecting

Christopher Reardon, Andrea Di Falco, Karl Welna, and Thomas Krauss  »View Author Affiliations


Optics Express, Vol. 17, Issue 5, pp. 3424-3428 (2009)
http://dx.doi.org/10.1364/OE.17.003424


View Full Text Article

Acrobat PDF (342 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We demonstrate beam deflection and multiple channel communication in free space optical communications using microprisms integrated directly onto an array of vertical cavity surface emitting lasers (VCSELs). The design and fabrication of such a transmitter is presented, and shown to achieve beam deflection of up to 10° in a planar configuration. A location discovery application, for use within a distributed network, is put forward and analysed.

© 2009 Optical Society of America

1. Introduction

Transmitting optical information via a free space beam is advantageous in many areas of technology, such as computer board-to-board interconnects [1

1. S. Sinzinger and J. Jahns, “Integrated micro-optical imaging-system with a high interconnection capacity fabricated in planar optics,” Appl. Opt. 36, 4729–4735 (1997). [CrossRef] [PubMed]

], optical sensing and optical communications, including distributed networks [2–4

2. Speckled Computing Website, http://www.specknet.org.

], that consist of simple subunits employing sensors, power supplies, and basic processors and that function as a whole by exchanging information.

Beam deflection has the role of addressing the receivers of information in such systems and is best done dynamically; dynamic beam deflection accounts for movement in the network as well facilitating the initial setup. Beam deflection can be done by moving a single beam, e.g. via micro-electro-mechanical system (MEMS) [5

5. J. Korvink and O. Paul, Editors, MEMS - a practical guide to design, analysis and applications (W. Andrew Publishing2006). [CrossRef]

] mirrors, or by “redundancy”. Redundancy means that the information is encoded onto one out of a large array of emitters, each of which points in a different direction. By activating the emitter that points into the desired direction, the information is sent to the correct recipient. While the latter approach appears wasteful at first sight, it is, in fact, more power efficient than actively moving the beam, since no power is consumed for the purpose of redirecting the beam. The fact that multiple emitters are required can be tolerated given the fact that current technology allows the placement of large arrays of emitters on a small area. For example, a large number of vertical cavity surface emitting lasers (VCSELs) [6

6. H. Li and K. Iga, Editors, Vertical-Cavity Surface-Emitting Laser (Devices Springer Series in Photonics2002).

] can be placed onto to a mm-size chip. Here, we discuss the “redundancy” approach and demonstrate it by integrating polymer microprisms onto a set of GaAs/AlGaAs VCSELs.

We use electron-beam greyscale lithography to create the microprisms. Greyscale lithography depends on partial cross-linking of a polymer, with the resulting film thickness being controlled by the electron dose. Unlike other approaches, such as thermal reflow [7

7. D. Daly, R. F. Stevens, M. C. Hutley, and N. Davies, “The manufacture of microlenses by melting photoresist,” Meas. Sci. Technol. 759–766 (1990). [CrossRef]

], greyscale lithography gives full control over the shape of the structure, and a number of interesting elements, such as axicons and spiral-phase-plates, can be produced via this route [8

8. V. Garces-Chavez, D. McGloin, H. Melville, W. Sibbett, and K. Dholakia, “Simultaneous micromanipulation in multiple planes using a self-reconstructing light beam,” Nature 419, 145–147 (2002). [CrossRef] [PubMed]

].

In the following sections we describe the fabrication of the VCSEL transmitter array and demonstrate beam deflection via microprisms. We then discuss the experimental results and finally propose a location discovery setup based on this system.

2. Design and fabrication

We utilised top emitting VCSELs (emitting at 980 nm) with oxide apertures in the experiment. The devices were fabricated by photolithography, chemically assisted ion beam etching (CAIBE) with chlorine as the reactive gas, and steam oxidation (450 °C, 25 min.). Individual devices were then isolated using photo-patterned SU-8 with separate Cr-Au contacts [14

14. D. Sameoto, S.-W. Lee, and M. Parameswaran, “Electrical interconnection through optimized wirebonding onto SU-8 structures and actuators,” J. Micromech. Microeng. 18, (2008). [CrossRef]

].

Figure 1 shows a chart of e-beam dose against resulting polymer film thickness, measured using a scanning electron microscope (SEM). A linear region is observed between the doses of 0.2 μAs/cm2 and 0.8 μAs/cm2 with a useful thickness range of approximately 5 μm.

Fig. 1. Resulting polymer thickness against electron-beam dose measured using a scanning electron microscope

The SU-8 was exposed accordingly in order to create prisms on top of the finished VCSEL. After exposure, the sample was developed in microposit EC solvent (Rohm and Haas Electronic Materials) for 2 minutes, and then rinsed in isopropyl alcohol (IPA). Hard-baking, of the polymer, is only carried out after development (180 °C, 10 min.); this hard-bake is also responsible for a small-scale smoothing of the prism surface (with final roughness well below λ/50 (i.e. less than 20 nm)). Since the overall height of the elements cannot be increased beyond 10 μm, the maximum angle of the prisms is limited; fig. 2(a) shows the profiles of three VCSELs with prisms of different lateral dimensions acquired with a surface profiler (Dektak 3 Auto 1). We measured angles of: α1 = 5.2°, α2 = 10.3° and α3 = 10.2° for 50- , 30-and 20-μm base-dimension prisms, respectively.

Figure 2(a) also gives an indication of the usable area (delimited by dotted lines) within each prism (defined as the point at which the angle of the prism changes by 10%). This area decreases as the slope of the prism is increased. Since the prisms are fabricated on top of 6 μm high mesas of 40 μm diameter, edge-effects are also seen to play a role. The 30 μm base prism appeared the best choice and was used in subsequent experiments. Figure 2(b) shows a completed device including a contact pad for wire-bonding and subsequent packaging of the transmitter array.

Fig. 2. (a) Surface profiles of three VCSELs with prisms of differing lateral dimensions. (b) SEM micrograph of a VCSEL with integrated microprism. Inset showing VCSEL contact pad (yellow), location of VCSEL emission aperture (red), and microprism angle profile (blue)

3. Experimental results

The emission lobes of the VCSELs were recorded via a detector mounted on a rotating arm, and are shown in fig. 3. The lobes of the two outer VCSELs in each array are deflected by ±5° from normal as a result of the 10° prism angle, given the n = 1.56 refractive index of SU-8. It is worth noting that the emission cone of each individual emitter is not compromised by passing through the microprism since all three emitters show equally wide cones and equal output for the same drive current, even though there is no prism on top of the central device. This is an advantage over diffractive-optic-elements (DOEs) and micro step-based blazed gratings, as they create higher order lobes alongside the desired steered-lobe [16

16. J. Yang, X. Su, P. Xu, and Z. Gu, “Beam steering and deflecting device using step-based micro-blazed grating,” Opt. Commun. 281, 3969–3976 (2008). [CrossRef]

].

Fig. 3. Emission lobe measurements of a microprism-steered VCSEL array. Inset shows a close-up of the deflection angle achieved.

On the other hand, it is obvious that the deflection angle is rather limited and one would like to achieve more than the ±5° demonstrated here. The most obvious approach would be to increase the thickness of the SU-8 layer and thereby the prism angle. This could be done by exposing the polymer on an e-beam system with a higher acceleration voltage, e.g. 50 kV or 100 kV. Alternatively, the pattern could be transferred into the semiconductor, which amplifies the beam deflection due to the considerably higher refractive index. This would require increasing the top-emitting VCSELs capping layer or the use of bottom-emitting VCSELs, since etching into the top mirror would compromise the laser feedback mechanism.

A key application area for this type of beam-deflection array is location discovery within a distributed network. Location discovery is a necessary step in identifying the source of information and their relative position in such a network. Here we show how a beam-deflection array can facilitate location discovery by identifying each transmitter with a different code, or in the simplest case, a different frequency.

A receiver was positioned at a distance of 30 cm from the transmitter chip and translated across the field of view with an automatic rotation stage. The three transmitters were modulated at different frequencies (6, 7 and 8 kHz, respectively) and the relative signal strengths at each position recorded. From the ratio between the signals received at the respective frequencies, it is then possible to deduce the position of the detector in the field of view. Figure 4 shows the corresponding translation measurements and fig. 5 shows the error in the position calculated from the experiment against the actual position of the detector.

Fig. 4. Received signal strength measurements as the detector is scanned across the VCSEL array from left to right
Fig. 5. Position error, of the detector obtained via the ratio of received signal powers from the transmitter (±1° error highlighted)

4. Conclusions

We have shown that, using greyscale e-beam lithography, it is possible to fabricate optical elements, (in this case microprisms), and integrate such elements onto an active laser device, in this case a VCSEL. We investigated the properties of the fabricated microprisms and found that a lateral dimension of 30 μm, resulted in a prism angle of 10.2° and a deflection angle of ±5°. We then demonstrated a potential application for such a system, namely its use for location discovery in a distributed network. We achieved such location discovery to an accuracy of ±1° over the useful range of ±10° of the array. By making prisms out of thicker SU-8 polymer and exposing it in an e-beam system with higher acceleration voltage, a larger range of angles could be covered with similar accuracy. This technique is particularly useful for prototyping devices but can be scaled up in volume in one of two ways. The use of electron beam lithography (EBL) on a large scale is not prohibitively difficult, each microelement takes a matter of seconds to expose and commercial EBL systems are widely available. This process could also be done with high energy beam sensitive (HEBS) glass as a grayscale mask, for increasing production volume.

Acknowledgments

This work was supported by the Consortium of Speckled Computing (EPSRC “Specknet”).

References and links

1.

S. Sinzinger and J. Jahns, “Integrated micro-optical imaging-system with a high interconnection capacity fabricated in planar optics,” Appl. Opt. 36, 4729–4735 (1997). [CrossRef] [PubMed]

2.

Speckled Computing Website, http://www.specknet.org.

3.

V. S. Hsu, J. M. Kahn, and K. S. J. Pister, “Wireless Communications for Smart Dust,” Electron. Res. Lab. Memo. M98/2, (1998).

4.

J. M. Kahn, R. H. Katz, and K. S. J. Pister, “Next Century Challenges: Mobile Networking for “Smart Dust,” Mobicom ’99, (1999).

5.

J. Korvink and O. Paul, Editors, MEMS - a practical guide to design, analysis and applications (W. Andrew Publishing2006). [CrossRef]

6.

H. Li and K. Iga, Editors, Vertical-Cavity Surface-Emitting Laser (Devices Springer Series in Photonics2002).

7.

D. Daly, R. F. Stevens, M. C. Hutley, and N. Davies, “The manufacture of microlenses by melting photoresist,” Meas. Sci. Technol. 759–766 (1990). [CrossRef]

8.

V. Garces-Chavez, D. McGloin, H. Melville, W. Sibbett, and K. Dholakia, “Simultaneous micromanipulation in multiple planes using a self-reconstructing light beam,” Nature 419, 145–147 (2002). [CrossRef] [PubMed]

9.

I.-H. Song, K.-N. Kang, Y. Jin, D. S.-W. Park, and P. K. Ajmera, “Microlens array fabrication by backside exposure using Fraunhofer diffraction,” Microsyst. Technol. 14, 1285–1290 (2008). [CrossRef]

10.

Y. Lu and S. Chen, “Direct write of microlens array using digital projection photopolymerization,” Appl. Phys. Lett. 92, (2008). [CrossRef]

11.

E. Bisaillon, D. F. Brosseau, T. Yamamoto, M. Mony, E. Bernier, D. Goodwill, D. V. Plant, and A. G. Kirk, “Free-space optical link with spatial redundancy for misalignment tolerance,” IEEE Photon. Technol. Lett. 14, 242–244 (2002). [CrossRef]

12.

C.-J. Yang, S.-H. Liu, H.-H. Hsieh, C.-C. Liu, T.-Y. Cho, and C.-C. Wu, “Microcavity top-emitting organic light-emitting devices integrated with microlens arrays: Simultaneous enhancement of quantum efficiency, cd/A efficiency, color performances, and image resolution,” Appl. Phys. Lett. 91, (2007). [PubMed]

13.

A. Braeuer, P. Dannberg, U. Zeitner, G. Mann, and W. Karthe, “Application oriented complex polymer microoptic,” Microsyst. Technol. 9, 304–307 (2003). [CrossRef]

14.

D. Sameoto, S.-W. Lee, and M. Parameswaran, “Electrical interconnection through optimized wirebonding onto SU-8 structures and actuators,” J. Micromech. Microeng. 18, (2008). [CrossRef]

15.

P. Mali, A. Sarkar, and R. Lal, “Facile fabrication of microfluidic systems using electron beam lithography,” Lab Chip 6, 310–315 (2006). [CrossRef] [PubMed]

16.

J. Yang, X. Su, P. Xu, and Z. Gu, “Beam steering and deflecting device using step-based micro-blazed grating,” Opt. Commun. 281, 3969–3976 (2008). [CrossRef]

OCIS Codes
(130.3120) Integrated optics : Integrated optics devices
(220.3740) Optical design and fabrication : Lithography
(200.2605) Optics in computing : Free-space optical communication
(140.7260) Lasers and laser optics : Vertical cavity surface emitting lasers
(130.3990) Integrated optics : Micro-optical devices

ToC Category:
Integrated Optics

History
Original Manuscript: December 5, 2008
Revised Manuscript: January 22, 2009
Manuscript Accepted: February 16, 2009
Published: February 19, 2009

Citation
Christopher Reardon, Andrea Di Falco, Karl Welna, and Thomas Krauss, "Integrated polymer microprisms for free space optical beam deflecting," Opt. Express 17, 3424-3428 (2009)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-17-5-3424


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. S. Sinzinger and J. Jahns, "Integrated micro-optical imaging-system with a high interconnection capacity fabricated in planar optics," Appl. Opt. 36, 4729-4735 (1997). [CrossRef] [PubMed]
  2. Speckled Computing Website, http://www.specknet.org.
  3. V. S. Hsu, J. M. Kahn, and K. S. J. Pister, "Wireless Communications for Smart Dust," Electron. Res. Lab. Memo.  M98/2, (1998).
  4. J. M. Kahn, R. H. Katz, and K. S. J. Pister, "Next Century Challenges: Mobile Networking for "Smart Dust," Mobicom ’99, (1999).
  5. J. Korvink and O. Paul, Editors, MEMS - a practical guide to design, analysis and applications (W. Andrew Publishing 2006). [CrossRef]
  6. H. Li and K. Iga, Editors, Vertical-Cavity Surface-Emitting Laser (Devices Springer Series in Photonics 2002).
  7. D. Daly, R. F. Stevens, M. C. Hutley, and N. Davies, "The manufacture of microlenses by melting photoresist," Meas. Sci. Technol. 1, 759-766 (1990). [CrossRef]
  8. V. Garces-Chavez, D. McGloin, H. Melville, W. Sibbett, and K. Dholakia, "Simultaneous micromanipulation in multiple planes using a self-reconstructing light beam," Nature 419, 145-147 (2002). [CrossRef] [PubMed]
  9. I.-H. Song, K.-N. Kang, Y. Jin, D. S.-W. Park, and P. K. Ajmera, "Microlens array fabrication by backside exposure using Fraunhofer diffraction," Microsyst. Technol. 14, 1285-1290 (2008). [CrossRef]
  10. Y. Lu and S. Chen, "Direct write of microlens array using digital projection photopolymerization," Appl. Phys. Lett. 92, 041109 (2008). [CrossRef]
  11. E. Bisaillon, D. F. Brosseau, T. Yamamoto, M. Mony, E. Bernier, D. Goodwill, D. V. Plant, and A. G. Kirk, "Free-space optical link with spatial redundancy for misalignment tolerance," IEEE Photon. Technol. Lett. 14, 242-244 (2002). [CrossRef]
  12. C.-J. Yang, S.-H. Liu, H.-H. Hsieh, C.-C. Liu, T.-Y. Cho, and C.-C. Wu, "Microcavity top-emitting organic light-emitting devices integrated with microlens arrays: Simultaneous enhancement of quantum efficiency, cd/A efficiency, color performances, and image resolution," Appl. Phys. Lett. 91, 63-64 (2007). [PubMed]
  13. A. Braeuer, P. Dannberg, U. Zeitner, G. Mann, and W. Karthe, "Application oriented complex polymer microoptic," Microsyst. Technol. 9, 304-307 (2003). [CrossRef]
  14. D. Sameoto, S.-W. Lee, and M. Parameswaran, "Electrical interconnection through optimized wirebonding onto SU-8 structures and actuators," J. Micromech. Microeng. 18, 075023 (2008). [CrossRef]
  15. P. Mali, A. Sarkar, and R. Lal, "Facile fabrication of microfluidic systems using electron beam lithography," Lab Chip 6, 310-315 (2006). [CrossRef] [PubMed]
  16. J. Yang, X. Su, P. Xu, and Z. Gu, "Beam steering and deflecting device using step-based micro-blazed grating," Opt. Commun. 281, 3969-3976 (2008). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited