OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 18, Iss. 11 — May. 24, 2010
  • pp: 10941–10946
« Show journal navigation

Wavelength-tunable silicon microring modulator

Po Dong, Roshanak Shafiiha, Shirong Liao, Hong Liang, Ning-Ning Feng, Dazeng Feng, Guoliang Li, Xuezhe Zheng, Ashok V. Krishnamoorthy, and Mehdi Asghari  »View Author Affiliations


Optics Express, Vol. 18, Issue 11, pp. 10941-10946 (2010)
http://dx.doi.org/10.1364/OE.18.010941


View Full Text Article

Acrobat PDF (789 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We present a wavelength-tunable, compact, high speed and low power silicon microring modulator. With a ring radius of 5 µm, we demonstrate a modulator with a high speed of 12.5 Gbps and a driving voltage of 3 V to achieve ~6 dB extinction ratio in high speed measurement. More importantly, tunability of the resonant wavelength is accomplished by means of a microheater on top of the ring, with an efficiency of 2.4 mW/nm (2.4 mW is needed to tune the resonant wavelength by 1 nm). This device aims to solve the narrow bandwidth problem of silicon microcavity modulators and increase the data bandwidth in optical interconnect systems.

© 2010 OSA

1. Introduction

Optical interconnect technology is expected as a key solution to solving major performance limitations in high performance computing caused by bus bandwidth bottleneck, latency and power consumption issues [1

1. R. A. Soref, “The past, present and future of silicon photonics,” IEEE. J. Sel. Top. Quantum Electron. 12(6), 1678–1687 (2006). [CrossRef]

5

5. I. Young, E. Mohammed, J. Liao, A. Kern, S. Palermo, B. Block, M. Reshotko, and P. Chang, “Optical I/O technology for tera-scale computing,” IEEE J. Solid-state Circuits 45(1), 235–248 (2010). [CrossRef]

]. A critical component in an optical interconnect is a high speed silicon optical modulator with low power/energy consumption and a small footprint [6

6. A. V. Krishnamoorthy, R. Ho, X. Zheng, H. Schwetman, J. Lexau, P. Koka, G. Li, I. Shubin, and J. E. Cunningham, “Computer systems based on silicon photonic interconnects,” Proc. IEEE 97, 1337–1361 (2009). [CrossRef]

]. While Mach-Zehnder interferometer (MZI) silicon modulators have been developed with speed up to 30 GHz, they usually exhibit a large footprint, have energy consumption greater than 5 pJ per bit, and require a large driving voltage of 6-8 V [7

7. A. Liu, R. Jones, L. Liao, D. Samara-Rubio, D. Rubin, O. Cohen, R. Nicolaescu, and M. Paniccia, “A high-speed silicon optical modulator based on a metal-oxide-semiconductor capacitor,” Nature 427(6975), 615–618 (2004). [CrossRef] [PubMed]

9

9. W. M. Green, M. J. Rooks, L. Sekaric, and Y. A. Vlasov, “Ultra-compact, low RF power, 10 Gb/s silicon Mach-Zehnder modulator,” Opt. Express 15(25), 17106–17113 (2007). [CrossRef] [PubMed]

]. These make them not suitable for the applications of chip-level optical interconnect. Promising compact and low power modulator candidates include carrier-injection silicon microring modulators [10

10. Q. Xu, B. Schmidt, S. Pradhan, and M. Lipson, “Micrometre-scale silicon electro-optic modulator,” Nature 435(7040), 325–327 (2005). [CrossRef] [PubMed]

, 11

11. S. Manipatruni, Q. Xu, B. Schmidt, J. Shakya, and M. Lipson, “High speed carrier injection 18 Gb/s silicon micro-ring electro-optic modulator,” in Proceedings of LEOS2007 (IEEE 2007), pp. 537–538.

], carrier-depletion microdisk and microring modulators [12

12. M. R. Watts, D. C. Trotter, R. W. Young, and A. L. Lentine, “Ultralow power silicon microdisk modulators and switches,” in Proceedings of 5th IEEE International Conference on Group IV Photonics (IEEE 2008), pp. 4 - 6.

, 13

13. P. Dong, S. Liao, D. Feng, H. Liang, D. Zheng, R. Shafiiha, C. C. Kung, W. Qian, G. Li, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low Vpp, ultralow-energy, compact, high-speed silicon electro-optic modulator,” Opt. Express 17(25), 22484–22490 (2009). [CrossRef]

], electro-absorption GeSi modulators using the Franz-Keldysh effect [14

14. J. Liu, D. Pan, S. Jongthammanurak, K. Wada, L. C. Kimerling, and J. Michel, “Design of monolithically integrated GeSi electro-absorption modulators and photodetectors on a SOI platform,” Opt. Express 15(2), 623–628 (2007). [CrossRef] [PubMed]

, 15

15. J. Liu, M. Beals, A. Pomerene, S. Bernardis, R. Sun, J. Cheng, L. C. Kimerling, and J. Michel, “Waveguide-integrated, ultralow-energy GeSi electro-absorption modulators,” Nat. Photonics 2(7), 433–437 (2008). [CrossRef]

], and GeSi quantum well modulators [16

16. J. E. Roth, O. Fidaner, R. K. Schaevitz, Y. H. Kuo, T. I. Kamins, J. S. Harris, and D. A. B. Miller, “Optical modulator on silicon employing germanium quantum wells,” Opt. Express 15(9), 5851–5859 (2007). [CrossRef] [PubMed]

]. The spectral bandwidth of microcavities is usually less than 1 nm and that of GeSi modulators is about 15 nm. Therefore, all these modulators suffer from a narrow bandwidth, which limits possible data bandwidth enabled by wavelength multiplexing techniques. The need for wavelength-tunable microcavity modulators is even greater due to the uncertainty in resonance wavelength arising from tolerances in the fabrication process [6

6. A. V. Krishnamoorthy, R. Ho, X. Zheng, H. Schwetman, J. Lexau, P. Koka, G. Li, I. Shubin, and J. E. Cunningham, “Computer systems based on silicon photonic interconnects,” Proc. IEEE 97, 1337–1361 (2009). [CrossRef]

]. Here we demonstrate a high speed silicon microring modulator with a local microheater. The local heater can heat up the ring and red-shift the resonance, with a tuning efficiency of 2.4 mW/nm (2.4 mW heating power is needed to shift the resonant wavelength by 1 nm). High speed modulation is achieved by carrier depletion in a reverse-biased pn junction embedded in the ring; the modulator exhibits a drive voltage of 3 V, a high speed of 12.5 Gbps, ultralow modulation energy consumption of 40 fJ per bit (not including tuning power), and a small ring radius of 5 µm.

2. Design and fabrication

The use of microrings or microdisks can dramatically reduce modulation power and device size by exploiting optical field confinement in a small area. Further advantages include high modulation ratios, low insertion losses, and low Vpp (peak-to-peak swing voltage) [13

13. P. Dong, S. Liao, D. Feng, H. Liang, D. Zheng, R. Shafiiha, C. C. Kung, W. Qian, G. Li, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low Vpp, ultralow-energy, compact, high-speed silicon electro-optic modulator,” Opt. Express 17(25), 22484–22490 (2009). [CrossRef]

]. The microring modulator presented here consists of a ring resonator coupled to a neighboring bus waveguide. The bus and ring waveguides have a width of 0.5 µm, a height of 0.25 µm and a slab height of 50 nm [Fig. 1(a)
Fig. 1 (a) Cross-section of the designed modulator with a local heater. (b) Top-view SEM image of the fully fabricated microring modulator. The ring radius is 5 µm.
]. The ring radius is 5 µm and the ring-bus gap is 150 nm. Tuning the effective index of the ring waveguide modifies the resonant wavelength which induces a strong modulation of the transmitted signal at the resonance wavelength. Reverse-biased pn diodes or forward-biased p-i-n diodes have been demonstrated to realize high speed modulation of silicon waveguides [8

8. A. Liu, L. Liao, D. Rubin, H. Nguyen, B. Ciftcioglu, Y. Chetrit, N. Izhaky, and M. Paniccia, “High-speed optical modulation based on carrier depletion in a silicon waveguide,” Opt. Express 15(2), 660–668 (2007). [CrossRef] [PubMed]

13

13. P. Dong, S. Liao, D. Feng, H. Liang, D. Zheng, R. Shafiiha, C. C. Kung, W. Qian, G. Li, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low Vpp, ultralow-energy, compact, high-speed silicon electro-optic modulator,” Opt. Express 17(25), 22484–22490 (2009). [CrossRef]

] through plasma dispersion effects [17

17. R. A. Soref and B. R. Bennett, “Electrooptical effects in silicon,” IEEE J. Quantum Electron. 23(1), 123–129 (1987). [CrossRef]

]. Here, we designed an asymmetric lateral pn junction with a p doping concentration of 5x1017 cm−3 and an n doping concentration of 1x1018 cm−3 [13

13. P. Dong, S. Liao, D. Feng, H. Liang, D. Zheng, R. Shafiiha, C. C. Kung, W. Qian, G. Li, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low Vpp, ultralow-energy, compact, high-speed silicon electro-optic modulator,” Opt. Express 17(25), 22484–22490 (2009). [CrossRef]

]. We fabricated the device on a silicon-on-insulator (SOI) platform with a 3-µm-thick buried oxide. Following waveguide trench etching, multiple lithography steps were used to define various doping areas. High-energy ion implantation and rapid thermal annealing defined the pn diode and the heavy doping regions. A 1.2 µm-thick oxide was deposited as the top cladding layer. A 100 nm-thick Ti film was then deposited on top of the cladding and along the ring, which acts as a local heater. The heater has a width of 1 µm. Figure 1(b) shows a top-view scanning electron microscopy (SEM) image of a fully fabricated ring modulator.

3. Measurement

We characterize the heater efficiency by measuring the transmission spectra under different heating powers, as shown in Fig. 2(a)
Fig. 2 (a) Transmission spectra of the ring resonator with different heating power. (b) Resonant wavelength versus heating power and its linear fitting.
. As we increase the electrical power of the metal heater, the temperature of the ring waveguide rises, which produces a resonance red-shift (silicon has a thermal coefficient of ~1.86x10−4/°C). The resonant wavelength is extracted as a function of heating power, presented in Fig. 2(b). The linear fitting shows that the power to shift the resonance of 1 nm is 2.4 mW. Since the free spectral range (FSR) of this ring is ~19.5 nm, the power to tune one whole FSR is about 46 mW. This tuning power is comparable to that reported for passive silicon ring resonators [18

18. N. Sherwood-Droz, H. Wang, L. Chen, B. G. Lee, A. Biberman, K. Bergman, and M. Lipson, “Optical 4x4 hitless slicon router for optical Networks-on-Chip (NoC),” Opt. Express 16(20), 15915–15922 (2008). [CrossRef] [PubMed]

] but higher than for recently reported optimized heaters [19

19. M. Watts, W. Zortman, D. Trotter, G. Nielson, D. Luck, and R. Young, “Adiabatic resonant microrings (ARMs) with directly integrated thermal microphotonics,” In Conference on Lasers and Electro-Optics / Quantum Electronics and Laser Science Conference (CLEO/QELS 2009), paper CPDB10.

, 20

20. P. Dong, W. Qian, H. Liang, R. Shafiiha, N.-N. Feng, D. Feng, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low power and compact reconfigurable multiplexing devices based on silicon microring resonators,” Opt. Express 18(10), 9852–9858 (2010). [CrossRef] [PubMed]

]. Compared with passive only rings where the silicon substrates are the main heat sink, the metal contacts of the pn junction also dissipate heat, which reduces the heating efficiency. From Fig. 2, it is seen that the extinction ratio (ER) of the ring resonance varies with ring temperature, however, a >10 dB ER is achievable over the heating range. This ER variation may be due to the coupling variation between the bus waveguide and the ring or the ring waveguide loss variation arising from the opto-elastic effect.

The high speed modulation is achieved by modulating the reverse bias of the pn junction. We measured the transmission spectra under different bias voltages, as shown in Fig. 3
Fig. 3 Transmission spectra of the ring at different bias voltages.
. The quality factor of the ring resonator is estimated at ~9000. From the value of the quality factor, we estimate that the ring waveguide has a propagation loss of ~45 dB/cm, which comes from the doping and also from the sidewall roughness. The resonance shift per unit voltage is 16.5 pm/V. A Vpp of 3V is sufficient to achieve a modulation depth of >6 dB. Considering an experimentally measured junction capacitance of ~17 fF for our device and a Vpp of 3 V, we can obtain the energy consumption as ~40 fJ/bit [13

13. P. Dong, S. Liao, D. Feng, H. Liang, D. Zheng, R. Shafiiha, C. C. Kung, W. Qian, G. Li, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low Vpp, ultralow-energy, compact, high-speed silicon electro-optic modulator,” Opt. Express 17(25), 22484–22490 (2009). [CrossRef]

].

In order to verify the feasibility of high temperature operation, we carried out eye diagram measurement with different heating powers. The modulator was driven by an NRZ PRBS 223-1 signal with a Vpp of 1.5 V and a d.c. bias of −1 V through a high speed probe. Due to microwave reflection from the modulator to the probe, the actual Vpp applied on the ring modulator is expected to be 3 V. The optical output was amplified by an erbium doped fiber amplifier (EDFA) and then measured using a high-speed oscilloscope equipped with an optical detector. The measured eye diagrams exhibit clear eye openings for 12.5 Gbps with a modulation depth of about 6 dB without any heating (i.e., at room temperature), as shown in Fig. 4(a)
Fig. 4 (a) 12.5 Gbps modulation of the device without any heating power at a wavelength of 1550.70 nm. (b) 12.5 Gbps modulation of the device with 18 mW heating power at a wavelength of 1558.00 nm. The temperature increase is expected to be ~93 °C.
. The noise in the eye diagrams may come from the EDFA and/or the microwave reflection. We then applied a heating power of 18 mW, which tunes the ring resonance from 1550.7 nm to 1558.0 nm. An eye diagram with an input wavelength of 1558.0 nm was then collected, shown in Fig. 4(b). Since the resonance shift can be expressed byΔλ=λng(NeffT)ΔT, where Neff is the effective index and ng is the group index, the theoretical resonance shift efficiency is ΔλΔT0.078  nm/°C. The temperature increase of the ring with 18 mW heating power is therefore expected to be ~93 °C for the ring waveguide. Comparing Fig. 4(b) with Fig. 4(a), we do not see detrimental effects due to this high temperature operation. The current density in the heater is estimated about 3.5 MA/cm2, for which electro-migration effects may occur to degrade the heater performance. Careful design of heater width and thickness and/or the use of other heater metals/alloys may be needed to avoid this effect. In addition, the resistivity increase of our Ti heater with respect to temperature was measured as ~0.4% per degree.

4. Discussion and conclusion

The thermal tuning power would not increase if the modulation speed increases. From the quality factor (~9000) and series resistance of our device (measured as ~100 ohm), our ring modulator should be able to operate at 20 Gbps [13

13. P. Dong, S. Liao, D. Feng, H. Liang, D. Zheng, R. Shafiiha, C. C. Kung, W. Qian, G. Li, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low Vpp, ultralow-energy, compact, high-speed silicon electro-optic modulator,” Opt. Express 17(25), 22484–22490 (2009). [CrossRef]

]. Recently reported ring modulator by other groups also demonstrates a high speed 3 dB bandwidth of 19 GHz [21

21. F. Y. Gardes, A. Brimont, P. Sanchis, G. Rasigade, D. Marris-Morini, L. O’Faolain, F. Dong, J. M. Fedeli, P. Dumon, L. Vivien, T. F. Krauss, G. T. Reed, and J. Martí, “High-speed modulation of a compact silicon ring resonator based on a reverse-biased pn diode,” Opt. Express 17(24), 21986–21991 (2009). [CrossRef] [PubMed]

]. Therefore, if adding a thermal tuning power of 12 mW which can shift the resonance by ~5 nm (5 nm would allow a temperature tolerance of ~65 °C), the total energy consumption would increase to ~650 fJ/bit under 20 Gbps operation. More efficient heating configurations may be designed using techniques such as thermal isolation beneath modulators [20

20. P. Dong, W. Qian, H. Liang, R. Shafiiha, N.-N. Feng, D. Feng, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low power and compact reconfigurable multiplexing devices based on silicon microring resonators,” Opt. Express 18(10), 9852–9858 (2010). [CrossRef] [PubMed]

] or using waveguides as a heating resistor [19

19. M. Watts, W. Zortman, D. Trotter, G. Nielson, D. Luck, and R. Young, “Adiabatic resonant microrings (ARMs) with directly integrated thermal microphotonics,” In Conference on Lasers and Electro-Optics / Quantum Electronics and Laser Science Conference (CLEO/QELS 2009), paper CPDB10.

] (~0.55 mW/nm efficiency has been demonstrated). This would bring down the total energy consumption of modulation and tuning to under 500 fJ/bit. Further power reduction can be realized by reducing the ring radius since the tuning efficiency is usually proportional to the inverse of the ring radius (microrings with a 1.5 µm radius and with similar waveguide geometry have been demonstrated in Ref [22

22. Q. Xu, D. Fattal, and R. G. Beausoleil, “Silicon microring resonators with 1.5-microm radius,” Opt. Express 16(6), 4309–4315 (2008). [CrossRef] [PubMed]

].). Even including this tuning power, the energy consumption of ring modulators is still significantly lower than that of MZI modulators which is usually larger than 5 pJ/bit. In addition, as demonstrated in Ref [20

20. P. Dong, W. Qian, H. Liang, R. Shafiiha, N.-N. Feng, D. Feng, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low power and compact reconfigurable multiplexing devices based on silicon microring resonators,” Opt. Express 18(10), 9852–9858 (2010). [CrossRef] [PubMed]

], 15 µm spacing is sufficient to avoid thermal crosstalk if more ring modulators are needed on a single chip, resulting in much more compact devices than MZI modulators.

In conclusion, a compact (5 µm radius ring), high-speed (12.5 Gbps) silicon electro-optic microring modulator with a low Vpp (3V) has been demonstrated with tunable resonance accomplished by means of a local microheater. This modulator consists of a ring resonator as an optical platform and realizes index modulation by using a reversed-biased lateral pn diode embedded in the ring. The heater on top of the ring can tune the resonance wavelength with an efficiency of 2.4 mW/nm. This device aims to solve the narrow bandwidth problem of silicon microcavity modulators and increase the data bandwidth in optical interconnect systems. To the best of our knowledge, this is the first experimental realization of microring modulators integrated with local metal heaters, although passive silicon rings with heaters have been demonstrated [18

18. N. Sherwood-Droz, H. Wang, L. Chen, B. G. Lee, A. Biberman, K. Bergman, and M. Lipson, “Optical 4x4 hitless slicon router for optical Networks-on-Chip (NoC),” Opt. Express 16(20), 15915–15922 (2008). [CrossRef] [PubMed]

20

20. P. Dong, W. Qian, H. Liang, R. Shafiiha, N.-N. Feng, D. Feng, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low power and compact reconfigurable multiplexing devices based on silicon microring resonators,” Opt. Express 18(10), 9852–9858 (2010). [CrossRef] [PubMed]

]. The metal heaters enable wide tuning ranges, much larger than that of forward biased p-j-n junction based heaters demonstrated in Ref [23

23. S. Manipatruni, R. K. Dokania, B. Schmidt, N. Sherwood-Droz, C. B. Poitras, A. B. Apsel, and M. Lipson, “Wide temperature range operation of micrometer-scale silicon electro-optic modulators,” Opt. Lett. 33(19), 2185–2187 (2008). [CrossRef] [PubMed]

]. In addition, we would like to stress that athermal operation of ring resonators and couplers have been demonstrated [24

24. B. Guha, B. B. C. Kyotoku, and M. Lipson, “CMOS-compatible athermal silicon microring resonators,” Opt. Express 18(4), 3487–3493 (2010). [CrossRef] [PubMed]

,25

25. B. Chen, H. Lu, D. Zhao, Y. Yuan, and M. Iso, “Optimized Design of Polarization-Independent and Temperature-Insensitive Broadband Optical Waveguide Coupler by Use of Fluorinated Polyimide,” Appl. Opt. 42(20), 4196–4201 (2003). [CrossRef] [PubMed]

], however, submicron silicon waveguides are very sensitive to fabrication variations and athermal operation limits the application of the thermo-optic effect to compensate the wavelength variation arising from fabrication tolerance [20

20. P. Dong, W. Qian, H. Liang, R. Shafiiha, N.-N. Feng, D. Feng, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low power and compact reconfigurable multiplexing devices based on silicon microring resonators,” Opt. Express 18(10), 9852–9858 (2010). [CrossRef] [PubMed]

].

Acknowledgements

The authors acknowledge funding of this work by DARPA MTO office under UNIC program supervised by Jagdeep Shah (contract agreement with SUN Microsystems HR0011-08-9-0001). The authors greatly acknowledge Dr. W. Qian, Dr. C. C. Kung, Dr. D. Zheng, Dr. J. Fong and Dr. B. J. Luff from Kotura Inc. for their work in fabricating of the device and revising the manuscript, and Dr. J. E. Cunningham and Dr. K. Raj from SUN Microsystems for helpful discussions. The views, opinions, and/or findings contained in this article/presentation are those of the author/presenter and should not be interpreted as representing the official views or policies, either expressed or implied, of the Defense Advanced Research Projects Agency or the Department of Defense. Approved for Public Release. Distribution Unlimited.

References and Links

1.

R. A. Soref, “The past, present and future of silicon photonics,” IEEE. J. Sel. Top. Quantum Electron. 12(6), 1678–1687 (2006). [CrossRef]

2.

L. C. Kimerling., “Electronic–photonic integrated circuits on the CMOS platform,” Proc. SPIE 6125, 6–15 (2006).

3.

D. A. B. Miller, “Optical interconnects to silicon,” IEEE J. Sel. Top. Quantum Electron. 6(6), 1312–1317 (2000). [CrossRef]

4.

B. Jalali, M. Paniccia, and G. Reed, “Silicon photonics,” IEEE Microw. Mag. 7(3), 58–68 (2006). [CrossRef]

5.

I. Young, E. Mohammed, J. Liao, A. Kern, S. Palermo, B. Block, M. Reshotko, and P. Chang, “Optical I/O technology for tera-scale computing,” IEEE J. Solid-state Circuits 45(1), 235–248 (2010). [CrossRef]

6.

A. V. Krishnamoorthy, R. Ho, X. Zheng, H. Schwetman, J. Lexau, P. Koka, G. Li, I. Shubin, and J. E. Cunningham, “Computer systems based on silicon photonic interconnects,” Proc. IEEE 97, 1337–1361 (2009). [CrossRef]

7.

A. Liu, R. Jones, L. Liao, D. Samara-Rubio, D. Rubin, O. Cohen, R. Nicolaescu, and M. Paniccia, “A high-speed silicon optical modulator based on a metal-oxide-semiconductor capacitor,” Nature 427(6975), 615–618 (2004). [CrossRef] [PubMed]

8.

A. Liu, L. Liao, D. Rubin, H. Nguyen, B. Ciftcioglu, Y. Chetrit, N. Izhaky, and M. Paniccia, “High-speed optical modulation based on carrier depletion in a silicon waveguide,” Opt. Express 15(2), 660–668 (2007). [CrossRef] [PubMed]

9.

W. M. Green, M. J. Rooks, L. Sekaric, and Y. A. Vlasov, “Ultra-compact, low RF power, 10 Gb/s silicon Mach-Zehnder modulator,” Opt. Express 15(25), 17106–17113 (2007). [CrossRef] [PubMed]

10.

Q. Xu, B. Schmidt, S. Pradhan, and M. Lipson, “Micrometre-scale silicon electro-optic modulator,” Nature 435(7040), 325–327 (2005). [CrossRef] [PubMed]

11.

S. Manipatruni, Q. Xu, B. Schmidt, J. Shakya, and M. Lipson, “High speed carrier injection 18 Gb/s silicon micro-ring electro-optic modulator,” in Proceedings of LEOS2007 (IEEE 2007), pp. 537–538.

12.

M. R. Watts, D. C. Trotter, R. W. Young, and A. L. Lentine, “Ultralow power silicon microdisk modulators and switches,” in Proceedings of 5th IEEE International Conference on Group IV Photonics (IEEE 2008), pp. 4 - 6.

13.

P. Dong, S. Liao, D. Feng, H. Liang, D. Zheng, R. Shafiiha, C. C. Kung, W. Qian, G. Li, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low Vpp, ultralow-energy, compact, high-speed silicon electro-optic modulator,” Opt. Express 17(25), 22484–22490 (2009). [CrossRef]

14.

J. Liu, D. Pan, S. Jongthammanurak, K. Wada, L. C. Kimerling, and J. Michel, “Design of monolithically integrated GeSi electro-absorption modulators and photodetectors on a SOI platform,” Opt. Express 15(2), 623–628 (2007). [CrossRef] [PubMed]

15.

J. Liu, M. Beals, A. Pomerene, S. Bernardis, R. Sun, J. Cheng, L. C. Kimerling, and J. Michel, “Waveguide-integrated, ultralow-energy GeSi electro-absorption modulators,” Nat. Photonics 2(7), 433–437 (2008). [CrossRef]

16.

J. E. Roth, O. Fidaner, R. K. Schaevitz, Y. H. Kuo, T. I. Kamins, J. S. Harris, and D. A. B. Miller, “Optical modulator on silicon employing germanium quantum wells,” Opt. Express 15(9), 5851–5859 (2007). [CrossRef] [PubMed]

17.

R. A. Soref and B. R. Bennett, “Electrooptical effects in silicon,” IEEE J. Quantum Electron. 23(1), 123–129 (1987). [CrossRef]

18.

N. Sherwood-Droz, H. Wang, L. Chen, B. G. Lee, A. Biberman, K. Bergman, and M. Lipson, “Optical 4x4 hitless slicon router for optical Networks-on-Chip (NoC),” Opt. Express 16(20), 15915–15922 (2008). [CrossRef] [PubMed]

19.

M. Watts, W. Zortman, D. Trotter, G. Nielson, D. Luck, and R. Young, “Adiabatic resonant microrings (ARMs) with directly integrated thermal microphotonics,” In Conference on Lasers and Electro-Optics / Quantum Electronics and Laser Science Conference (CLEO/QELS 2009), paper CPDB10.

20.

P. Dong, W. Qian, H. Liang, R. Shafiiha, N.-N. Feng, D. Feng, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low power and compact reconfigurable multiplexing devices based on silicon microring resonators,” Opt. Express 18(10), 9852–9858 (2010). [CrossRef] [PubMed]

21.

F. Y. Gardes, A. Brimont, P. Sanchis, G. Rasigade, D. Marris-Morini, L. O’Faolain, F. Dong, J. M. Fedeli, P. Dumon, L. Vivien, T. F. Krauss, G. T. Reed, and J. Martí, “High-speed modulation of a compact silicon ring resonator based on a reverse-biased pn diode,” Opt. Express 17(24), 21986–21991 (2009). [CrossRef] [PubMed]

22.

Q. Xu, D. Fattal, and R. G. Beausoleil, “Silicon microring resonators with 1.5-microm radius,” Opt. Express 16(6), 4309–4315 (2008). [CrossRef] [PubMed]

23.

S. Manipatruni, R. K. Dokania, B. Schmidt, N. Sherwood-Droz, C. B. Poitras, A. B. Apsel, and M. Lipson, “Wide temperature range operation of micrometer-scale silicon electro-optic modulators,” Opt. Lett. 33(19), 2185–2187 (2008). [CrossRef] [PubMed]

24.

B. Guha, B. B. C. Kyotoku, and M. Lipson, “CMOS-compatible athermal silicon microring resonators,” Opt. Express 18(4), 3487–3493 (2010). [CrossRef] [PubMed]

25.

B. Chen, H. Lu, D. Zhao, Y. Yuan, and M. Iso, “Optimized Design of Polarization-Independent and Temperature-Insensitive Broadband Optical Waveguide Coupler by Use of Fluorinated Polyimide,” Appl. Opt. 42(20), 4196–4201 (2003). [CrossRef] [PubMed]

OCIS Codes
(200.4650) Optics in computing : Optical interconnects
(230.3120) Optical devices : Integrated optics devices
(250.5300) Optoelectronics : Photonic integrated circuits
(250.7360) Optoelectronics : Waveguide modulators

ToC Category:
Integrated Optics

History
Original Manuscript: February 12, 2010
Revised Manuscript: May 3, 2010
Manuscript Accepted: May 4, 2010
Published: May 10, 2010

Citation
Po Dong, Roshanak Shafiiha, Shirong Liao, Hong Liang, Ning-Ning Feng, Dazeng Feng, Guoliang Li, Xuezhe Zheng, Ashok V. Krishnamoorthy, and Mehdi Asghari, "Wavelength-tunable silicon microring modulator," Opt. Express 18, 10941-10946 (2010)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-18-11-10941


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. R. A. Soref, “The past, present and future of silicon photonics,” IEEE. J. Sel. Top. Quantum Electron. 12(6), 1678–1687 (2006). [CrossRef]
  2. L. C. Kimerling and ., “Electronic–photonic integrated circuits on the CMOS platform,” Proc. SPIE 6125, 6–15 (2006).
  3. D. A. B. Miller, “Optical interconnects to silicon,” IEEE J. Sel. Top. Quantum Electron. 6(6), 1312–1317 (2000). [CrossRef]
  4. B. Jalali, M. Paniccia, and G. Reed, “Silicon photonics,” IEEE Microw. Mag. 7(3), 58–68 (2006). [CrossRef]
  5. I. Young, E. Mohammed, J. Liao, A. Kern, S. Palermo, B. Block, M. Reshotko, and P. Chang, “Optical I/O technology for tera-scale computing,” IEEE J. Solid-state Circuits 45(1), 235–248 (2010). [CrossRef]
  6. A. V. Krishnamoorthy, R. Ho, X. Zheng, H. Schwetman, J. Lexau, P. Koka, G. Li, I. Shubin, and J. E. Cunningham, “Computer systems based on silicon photonic interconnects,” Proc. IEEE 97, 1337–1361 (2009). [CrossRef]
  7. A. Liu, R. Jones, L. Liao, D. Samara-Rubio, D. Rubin, O. Cohen, R. Nicolaescu, and M. Paniccia, “A high-speed silicon optical modulator based on a metal-oxide-semiconductor capacitor,” Nature 427(6975), 615–618 (2004). [CrossRef] [PubMed]
  8. A. Liu, L. Liao, D. Rubin, H. Nguyen, B. Ciftcioglu, Y. Chetrit, N. Izhaky, and M. Paniccia, “High-speed optical modulation based on carrier depletion in a silicon waveguide,” Opt. Express 15(2), 660–668 (2007). [CrossRef] [PubMed]
  9. W. M. Green, M. J. Rooks, L. Sekaric, and Y. A. Vlasov, “Ultra-compact, low RF power, 10 Gb/s silicon Mach-Zehnder modulator,” Opt. Express 15(25), 17106–17113 (2007). [CrossRef] [PubMed]
  10. Q. Xu, B. Schmidt, S. Pradhan, and M. Lipson, “Micrometre-scale silicon electro-optic modulator,” Nature 435(7040), 325–327 (2005). [CrossRef] [PubMed]
  11. S. Manipatruni, Q. Xu, B. Schmidt, J. Shakya, and M. Lipson, “High speed carrier injection 18 Gb/s silicon micro-ring electro-optic modulator,” in Proceedings of LEOS2007 (IEEE 2007), pp. 537–538.
  12. M. R. Watts, D. C. Trotter, R. W. Young, and A. L. Lentine, “Ultralow power silicon microdisk modulators and switches,” in Proceedings of 5th IEEE International Conference on Group IV Photonics (IEEE 2008), pp. 4 - 6.
  13. P. Dong, S. Liao, D. Feng, H. Liang, D. Zheng, R. Shafiiha, C. C. Kung, W. Qian, G. Li, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low Vpp, ultralow-energy, compact, high-speed silicon electro-optic modulator,” Opt. Express 17(25), 22484–22490 (2009). [CrossRef]
  14. J. Liu, D. Pan, S. Jongthammanurak, K. Wada, L. C. Kimerling, and J. Michel, “Design of monolithically integrated GeSi electro-absorption modulators and photodetectors on a SOI platform,” Opt. Express 15(2), 623–628 (2007). [CrossRef] [PubMed]
  15. J. Liu, M. Beals, A. Pomerene, S. Bernardis, R. Sun, J. Cheng, L. C. Kimerling, and J. Michel, “Waveguide-integrated, ultralow-energy GeSi electro-absorption modulators,” Nat. Photonics 2(7), 433–437 (2008). [CrossRef]
  16. J. E. Roth, O. Fidaner, R. K. Schaevitz, Y. H. Kuo, T. I. Kamins, J. S. Harris, and D. A. B. Miller, “Optical modulator on silicon employing germanium quantum wells,” Opt. Express 15(9), 5851–5859 (2007). [CrossRef] [PubMed]
  17. R. A. Soref and B. R. Bennett, “Electrooptical effects in silicon,” IEEE J. Quantum Electron. 23(1), 123–129 (1987). [CrossRef]
  18. N. Sherwood-Droz, H. Wang, L. Chen, B. G. Lee, A. Biberman, K. Bergman, and M. Lipson, “Optical 4x4 hitless slicon router for optical Networks-on-Chip (NoC),” Opt. Express 16(20), 15915–15922 (2008). [CrossRef] [PubMed]
  19. M. Watts, W. Zortman, D. Trotter, G. Nielson, D. Luck, and R. Young, “Adiabatic resonant microrings (ARMs) with directly integrated thermal microphotonics,” In Conference on Lasers and Electro-Optics / Quantum Electronics and Laser Science Conference (CLEO/QELS 2009), paper CPDB10.
  20. P. Dong, W. Qian, H. Liang, R. Shafiiha, N.-N. Feng, D. Feng, X. Zheng, A. V. Krishnamoorthy, and M. Asghari, “Low power and compact reconfigurable multiplexing devices based on silicon microring resonators,” Opt. Express 18(10), 9852–9858 (2010). [CrossRef] [PubMed]
  21. F. Y. Gardes, A. Brimont, P. Sanchis, G. Rasigade, D. Marris-Morini, L. O’Faolain, F. Dong, J. M. Fedeli, P. Dumon, L. Vivien, T. F. Krauss, G. T. Reed, and J. Martí, “High-speed modulation of a compact silicon ring resonator based on a reverse-biased pn diode,” Opt. Express 17(24), 21986–21991 (2009). [CrossRef] [PubMed]
  22. Q. Xu, D. Fattal, and R. G. Beausoleil, “Silicon microring resonators with 1.5-microm radius,” Opt. Express 16(6), 4309–4315 (2008). [CrossRef] [PubMed]
  23. S. Manipatruni, R. K. Dokania, B. Schmidt, N. Sherwood-Droz, C. B. Poitras, A. B. Apsel, and M. Lipson, “Wide temperature range operation of micrometer-scale silicon electro-optic modulators,” Opt. Lett. 33(19), 2185–2187 (2008). [CrossRef] [PubMed]
  24. B. Guha, B. B. C. Kyotoku, and M. Lipson, “CMOS-compatible athermal silicon microring resonators,” Opt. Express 18(4), 3487–3493 (2010). [CrossRef] [PubMed]
  25. B. Chen, H. Lu, D. Zhao, Y. Yuan, and M. Iso, “Optimized Design of Polarization-Independent and Temperature-Insensitive Broadband Optical Waveguide Coupler by Use of Fluorinated Polyimide,” Appl. Opt. 42(20), 4196–4201 (2003). [CrossRef] [PubMed]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1 Fig. 2 Fig. 3
 
Fig. 4
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited