OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 18, Iss. 14 — Jul. 5, 2010
  • pp: 15062–15072
« Show journal navigation

High-power, widely-tunable Cr2+:ZnSe master oscillator power amplifier systems

P. A. Berry and K. L. Schepler  »View Author Affiliations


Optics Express, Vol. 18, Issue 14, pp. 15062-15072 (2010)
http://dx.doi.org/10.1364/OE.18.015062


View Full Text Article

Acrobat PDF (1014 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We demonstrate high-power Cr2+:ZnSe master oscillator power amplifier (MOPA) pure continuous wave (CW) laser systems with output power of 14 W and amplifier gain greater than 2X. In addition, we develop a theoretical model for this type of amplification and show single-knob tunability at high powers over 400 nm.

© 2010 OSA

1. Introduction

The atmospheric transmission windows in the middle-infrared (mid-IR, 2-5 µm) wavelength range, coupled with organic and other chemical absorption lines occurring throughout this region give rise to a wide variety of medical, scientific, commercial and military applications. Communications, remote sensing, IR countermeasures, laser surgery and non-invasive imaging are just a few of the drivers of high-power solid-state mid-IR laser development. Transition-metal doped II-VI laser materials, such as Cr2+:ZnSe [1

1. L. D. DeLoach, R. H. Page, G. D. Wilke, S. A. Payne, and W. F. Krupke, “Transition metal-doped zinc chalcogenides: spectroscopy and laser demonstration of a new class of gain media,” IEEE J. Quantum Electron. 32(6), 885–895 (1996). [CrossRef]

, 2

2. R. H. Page, K. I. Schaffers, L. D. DeLoach, G. D. Wilke, F. D. Patel, J. B. Tassano Jr, S. A. Payne, W. F. Krupke, K. T. Chen, and A. Burger, “Cr2+-doped zinc chalcogenides as efficient, widely tunable mid-infrared lasers,” IEEE J. Quantum Electron. 33(4), 609–619 (1997). [CrossRef]

], Cr2+:ZnS [1

1. L. D. DeLoach, R. H. Page, G. D. Wilke, S. A. Payne, and W. F. Krupke, “Transition metal-doped zinc chalcogenides: spectroscopy and laser demonstration of a new class of gain media,” IEEE J. Quantum Electron. 32(6), 885–895 (1996). [CrossRef]

3

3. I. T. Sorokina, E. Sorokin, S. Mirov, V. Fedorov, V. Badikov, V. Panyutin, and K. I. Schaffers, “Broadly tunable compact continuous-wave Cr2+:ZnS laser,” Opt. Lett. 27(12), 1040–1042 (2002). [CrossRef]

], Cr2+:Cd1-xMnxTe [4

4. U. Hömmerich, X. Wu, V. R. Davis, S. B. Trivedi, K. Grasza, R. J. Chen, and S. Kutcher, “Demonstration of room-temperature laser action at 2.5 mum from Cr2+:Cd0.85Mn0.15Te,” Opt. Lett. 22(15), 1180–1182 (1997). [CrossRef] [PubMed]

], and Cr2+:CdSe [5

5. J. McKay, K. L. Schepler, and G. C. Catella, “Efficient grating-tuned mid-infrared Cr2+:CdSe laser,” Opt. Lett. 24(22), 1575–1577 (1999). [CrossRef]

], have many desirable properties such as wide tunability [6

6. U. Demirbas and A. Sennaroglu, “Intracavity-pumped Cr2+:ZnSe laser with ultrabroad tuning range between 1880 and 3100 nm,” Opt. Lett. 31(15), 2293–2295 (2006). [CrossRef] [PubMed]

], broad absorption bands, a large gain cross section, room-temperature operation and no excited state absorption [1

1. L. D. DeLoach, R. H. Page, G. D. Wilke, S. A. Payne, and W. F. Krupke, “Transition metal-doped zinc chalcogenides: spectroscopy and laser demonstration of a new class of gain media,” IEEE J. Quantum Electron. 32(6), 885–895 (1996). [CrossRef]

, 7

7. I. T. Sorokina, “Cr2+-doped II-VI materials for lasers and nonlinear optics,” Opt. Mater. 26(4), 395–412 (2004). [CrossRef]

].

Cr2+:ZnSe in particular has been shown to be capable of continuous wave (CW) output power levels exceeding 12 W [8

8. I. S. Moskalev, V. V. Fedorov, S. B. Mirov, P. A. Berry, and K. L. Schepler, “12-Watt CW Polycrystalline Cr2+:ZnSe Laser Pumped by Tm-fiber Laser,” in Advanced Solid State Photonics(Optical Society of America, Denver, CO, 2008), p. WB30.

], gain switched lasing with average output power of up to 18.5 W [9

9. T. J. Carrig, G. J. Wagner, W. J. Alford, and A. Zakel, “Chromium-doped chalcogenide lasers,” in Solid State Lasers and Amplifiers, A. Sennaroglu, J. G. Fujimoto, and C. R. Pollock, eds. (SPIE, Bellingham, WA, 2004), pp. 74–82.

], narrow-linewidth operation [10

10. G. J. Wagner, B. G. Tiemann, W. J. Alford, and T. J. Carrig, “Single-Frequency Cr:ZnSe Laser,” in Advanced Solid-State Photonics(Optical Society of America, 2004), p. WB12.

], and tunability from 1973 to 3339 nm [11

11. E. Sorokin, I. T. Sorokina, M. S. Mirov, V. V. Fedorov, I. S. Moskalev, and S. B. Mirov, “Ultrabroad Continuous-Wave Tuning of Ceramic Cr:ZnSe and Cr:ZnS Lasers,” in Advanced Solid-State Photonics(Optical Society of America, 2010), p. AMC2.

]. Only relatively recently have higher-quality Cr2+:ZnS crystals been fabricated and because of this, these types of lasers have not been as extensively demonstrated. However, they have been shown to be capable of multi-watt output [12

12. I. S. Moskalev, V. V. Fedorov, and S. B. Mirov, “10-watt, pure continuous-wave, polycrystalline Cr2+:ZnS laser,” Opt. Express 17(4), 2048–2056 (2009). [CrossRef] [PubMed]

], and can have some advantages over Cr2+:ZnSe with respect to physical properties [13

13. R. J. Harris, G. T. Johnston, G. A. Kepple, P. C. Krok, and H. Mukai, “Infrared thermooptic coefficient measurement of polycrystalline ZnSe, ZnS, CdTe, CaF2, and BaF2, single crystal KCI, and TI-20 glass,” Appl. Opt. 16(2), 436–438 (1977). [CrossRef] [PubMed]

, 14

14. D. M. Simanovskii, H. A. Schwettman, H. Lee, and A. J. Welch, “Midinfrared Optical Breakdown in Transparent Dielectrics,” Phys. Rev. Lett. 91(10), 107601 (2003). [CrossRef] [PubMed]

]. Power scaling of chromium lasers has long been hampered by the problem of thermal lensing due to the high thermo-optic coefficients of zinc sulfide (46 x 10−6 1/K), zinc selenide (70 x 10−6 1/K), CdSe and CdTe (both ~100 x 10−6 1/K) [7

7. I. T. Sorokina, “Cr2+-doped II-VI materials for lasers and nonlinear optics,” Opt. Mater. 26(4), 395–412 (2004). [CrossRef]

]. Self-focusing in the gain material leads to optical damage or cavity instability which limits the maximum achievable output power. These thermal issues can be addressed through appropriate choices of crystal geometry, a longer wavelength pump source and heat removal, all of which help to reduce the thermal load in the gain element [15

15. K. L. Schepler, R. D. Peterson, P. A. Berry, and J. B. McKay, “Thermal Effects in Cr2+:ZnSe Thin Disk Lasers,” IEEE J. Sel. Top. Quantum Electron. 11(3), 713–720 (2005). [CrossRef]

]. Even when these steps are taken to mitigate the thermal problems, the lasers are often still limited in their output characteristics. One solution to this problem is to use a master oscillator power amplifier (MOPA) architecture where the MO design is chosen to emphasize a desirable operating characteristic such as beam quality, linewidth or tunability while the amplifier section accomplishes the power scaling without degrading performance.

In this paper we present MOPA laser performance using polycrystalline Cr2+:ZnSe gain media in the conventional slab geometry for both the oscillator and the amplifier. We develop an improved amplifier gain model which incorporates variations in pump and signal beam parameters. We investigate a variety of MO configurations and their performance as part of a versatile MOPA-configuration laser system. We demonstrate 14 W of pure CW output and compare the system performance to the theoretical model. System versatility is demonstrated by multi-watt, narrow linewidth output tunable over a range greater than 400 nm. Beam quality and spectral content are also investigated.

2. Amplifier model

In order to design a MOPA Cr2+:ZnSe laser, a theoretical model was developed and used to determine possible amplifier performance for a given set of physical parameters. We considered optical pumping co-aligned with an input signal beam. Absorption by the Cr2+ ions is proportional to pump intensity so both pump intensity and absorbed power will decrease along the propagation direction. In addition, both the pump and signal are expected to have some non-uniform transverse distribution which we will model as well.

Any amplifier model must be based on known or measured material parameters involved in absorption and emission. The absorption and emission cross-sections for Cr2+:ZnSe vary in the literature (for example, between 0.9 x 10−18 and 1.3 x 10−18 cm2 for peak emission cross-section). This model will use values published by DeLoach et. al. [1

1. L. D. DeLoach, R. H. Page, G. D. Wilke, S. A. Payne, and W. F. Krupke, “Transition metal-doped zinc chalcogenides: spectroscopy and laser demonstration of a new class of gain media,” IEEE J. Quantum Electron. 32(6), 885–895 (1996). [CrossRef]

] but also acceptable would be those from Sorokina et. al. [7

7. I. T. Sorokina, “Cr2+-doped II-VI materials for lasers and nonlinear optics,” Opt. Mater. 26(4), 395–412 (2004). [CrossRef]

]. The absorption and emission cross-sections at the pump wavelength of 1.9 µm, σpa and σpe respectively, are 0.6 x 10−18 cm2 and 0.3 x 10−18 cm2 while the emission cross-section at the input signal wavelength of 2.5 µm, σse, is 0.9 x 10−18 cm2. The Cr2+ doping level, no, is calculated from the measured amount of a small signal (i.e. not close to saturating or bleaching the absorption) beam power transmitted through a Cr2+:ZnSe sample. A typical value of n0 is 1 x 1019 cm−3(~0.04% atomic) The Cr2+ ion in a tetrahedral crystal field is a 4-level system with fast relaxation in the vibronic sublevels which means that no is effectively the sum of n* and ng, where n* is the upper state population and ng is the unexcited (ground state) population.

In the case of a collinearly-pumped amplifier (where both the pump and signal beams propagate in the z-direction), the intensity-driven n* is not uniform with respect to z, but will decrease due to absorption of the pump. Thus the gain at each z location will also vary due to the intensity dependence of the pumping rate. In order to calculate gain, G, in our amplifier we need to understand the relationships between n*, the pump intensity, Ip and the input signal intensity, Is through a system of differential equations.

The differential equation for n* will have a positive term from absorption at the pump wavelength and negative terms from spontaneous emission and stimulated emission at the signal wavelength. In addition to these, because the absorption and emission bands of Cr2+:ZnSe overlap in the 1.9 µm region, there will also be a stimulated re-emission term at the pump wavelength as well. The absorption cross section at 2.5 µm is negligible in Cr2+:ZnSe so there will be no absorption term at the signal wavelength. The differential equation for the pump radiation intensity will have negative terms from absorption and passive losses at the pump wavelength in addition to a positive term due to stimulated re-emission at the pump wavelength. The differential equation for input signal intensity has a gain contribution from stimulated emission and passive losses at the signal wavelength.

It is convenient to define the pump and signal intensities in dimensionless units so that we have (6) and (7),
Jp(z,r)=Ip(z,r)hνp(σpa+σpe)τ=Ip(z,r)Ip,sat
(6)
Js(z,r)=Is(z,r)hνsσseτ=Is(z,r)Is,sat
(7)
where Is,sat and Is,sat are the saturation intensities for signal and pump wavelengths. With these definitions, neglecting radial dependence and assuming negligible passive losses gives the system in (8-10).

n*(z)=n0σpa(σpa+σpe)Jp(z)Jp(z)+Js(z)+1
(8)
dJp(z)dz=Jp(z)[σpan0+(σpa+σpe)n*(z)]
(9)
dJs(z)dz=Js(z)σsen*(z)
(10)

These equations can be solved numerically for some initial pump and signal intensities, Ip0 and Is0 and a crystal length L. This system assumes that both the signal and pump beams of a given power have a uniform transverse intensity over a circular area A (with say a radius of r). In practice, however, the pump and signal beams both have some non-uniform, mostly Gaussian transverse intensity distribution. In order to model the radial dependence, we must run the z-propagation model for points along the radius with intensities given by the Gaussian distribution (11) of r (with a 1/e2 radius of δ and a Gaussian order N) and integrate them over r and θ to get an output power.

I(r,δ,N)=exp(2r2Nδ2N)
(11)

This can take into account non-uniform saturation effects in the center of the signal beam where intensities are higher. The end result of which could be beams which become less Gaussian as they are amplified.

3. Experimental design

One of the advantages of the MOPA design is the flexibility to use almost any combination of oscillator and amplifier. A variety of MO designs were built and tested with the simplest PA design. This was done to evaluate the advantages of each design while adhering to the optimum PA design with respect to simplicity and performance predicted by the model. MO designs were selected for their ability to optimize certain operating modes such as tunability, narrow linewidth or power output.

There are a number of situations which may require the orientation of the laser crystal at Brewster’s angle in a laser cavity. Anti-reflective (AR) coatings in the 2-3 µm region may be too costly or not robust enough for use and thus another method is needed to reduce reflective losses. However, using a crystal at Brewster’s angle carries with it some negative astigmatism effects which are compounded by thermal lensing in the crystal which is now at an angle. To counteract this, advantage can be taken of the astigmatism-compensating properties of cavity configurations first used by Kogelnik in dye laser cavities [18

18. H. Kogelnik, E. Ippen, A. Dienes, and C. Shank, “Astigmatically compensated cavities for CW dye lasers,” IEEE J. Quantum Electron. 8(3), 373–379 (1972). [CrossRef]

].

Our initial approach used a Kogelnik-type cavity with a single collimated leg represented in Fig. 2
Fig. 2 Astigmatically-compensated Z-cavity design which can use either a single collimated-leg design (dashed) or a double-collimated leg design. OC = output coupler, LP = laser pump lens, FE = functional element.
by the dashed lines. The cavity consisted of a flat 45° dichroic input coupler (M2), AR-coated for 1.9 µm and high reflectivity (HR)-coated for 2-3 µm; two 5 cm radius of curvature (ROC) spherical mirrors (M1); and a flat CaF2 50% reflective (R) output coupler (OC) located ~16 cm from M1. The pump focusing lens (LP) had an experimentally-determined optimal focal length of 5 cm. The polycrystalline, 8.9x7.0x3.0 mm (LxWxH) Cr2+:ZnSe gain element was pumped along the long dimension with a Tm-fiber laser linearly polarized parallel to the plane of the diagram. The fiber nature of the pump system and the lack of high-power isolators at 1.9 µm required that this and all subsequent designs incorporate a non-normal incidence input coupler to prevent back-reflection. This cavity was shown to be capable of over 12 W of pure CW power [8

8. I. S. Moskalev, V. V. Fedorov, S. B. Mirov, P. A. Berry, and K. L. Schepler, “12-Watt CW Polycrystalline Cr2+:ZnSe Laser Pumped by Tm-fiber Laser,” in Advanced Solid State Photonics(Optical Society of America, Denver, CO, 2008), p. WB30.

]. This single-leg cavity was limited however, in that its output beam quality and stability were poor at higher operating powers which essentially precluded quality focusing and overlap in the amplifier. It also had no good location in which to insert functional elements such as a grating for tunability or a saturable absorber for modelocking.

To address these concerns, a double collimated-leg Z-cavity was assembled as illustrated with the solid elements in Fig. 2. The same 5 cm ROC mirror (M1) used as an end mirror in the above cavity was moved one focal length from the gain element and used as the input coupler while also creating the second collimated leg. The ~16 cm long ‘functional element’ (FE) leg was terminated with a planar HR mirror for free-running mode or a 300 gr/mm, 2.5 µm blazed grating in the Littrow configuration for tuning and line narrowing. It was found experimentally that the optimal pump lens (LP) focal length was 7.5 cm and optimal outcoupler reflectivity was 70%. Modeling cavity mode overlap with the pump can be accomplished using a standard ABCD matrix method, but the results were merely a good starting point experimentally due to the variable and strong nature of the thermal lensing.

When robust AR coatings are available, some of the astigmatism problems can be eliminated by utilizing a normal-incidence L-cavity pumping scheme. This simplifies the cavity considerably as seen in Fig. 3A
Fig. 3 A) Normal-incidence L-cavity scheme which can use either an HR curved mirror (M1) or a combination of planar HR (M2) and positive lens (L1). B) Power amplifier design where LMO and LPA are chosen for optimal overlap of pump and signal beams.
. Cavity stability can be achieved using either a concave HR end mirror (La-cavity) or a planar HR end mirror with an intracavity AR coated positive lens (Lb-cavity). The latter configuration is more complicated to construct in confined quarters and may have some loss depending on the quality of the AR coating but M2 could be replaced with a grating in the Littrow configuration to achieve cavity tuning. Both cavities had an optimal outcoupler reflectivity of 70% and pump lens focal lengths of 5 cm.

The power amplifier section used a co-linearly pumped, polycrystalline, 8.9x7.0x3.0 mm (LxWxH) Cr2+:ZnSe crystal similar to the MO crystal, but AR coated for 1.9-3 µm. As seen in Fig. 3B, the 150 W maximum, 1.9 µm, Tm-fiber laser pump beam is co-aligned with the MO output. Both beams are focused for optimal mode overlap of around 100 µm radius with 15 cm focal length lenses (LMO and LPA) for the Z-cavity or 80 µm with 5 cm focal length lenses for the L-cavities.

4. Experimental results

The Z- and L-cavity oscillators were optimized for highest output (Z-cavity) or just below the damage threshold for the AR coatings (L-cavities). All experiments were done with the laser samples cooled with circulating water maintained at 10° C. Experimentally, it was determined that the Lb-cavity was easily out-performed by the La-cavity, possibly due to additional losses from the intra-cavity lens (~5% per pass). Once an MO was optimized in this way, the PA pump power was then varied to test the system and compare to the theoretical model. The data shown in Fig. 4
Fig. 4 Power scaling ability of MOPA configurations. Experimental data (discrete points) is compared with model predictions for La- and Z-cavities, both with 80 µm and 100 μm spot sizes, respectively.
represents the best performance of each of the MOPA configurations. From this, it can be seen that the La-cavity is better suited for power scaling than the Z-cavity. This is likely due to the limited ability of the fixed-angle curved mirrors in the Z-cavity to compensate for the increasing astigmatism from the Brewster-angle thermal lens in the gain element. However, it should be noted that the output from the Z-cavity is tunable and, due to the poor performance of the Lb-cavity, this is not an option in the linear cavity configuration.

The experimental data follows the model-predicted performance at lower pump powers when thermal lensing in the amplifier crystal is low. As the thermal lens power increases however, the size of the pump and signal beams are affected by the lens and begin to deviate from the values which were used in the model. This, along with any changes in overlap between the two beams, causes the differences between the model and experiment. Experimental evidence also showed that longer amplifier crystals showed little improvement in amplification, supporting the model predictions about pump depletion levels at higher pump powers.

The output spectrum of the free-running (no grating present) Lb-cavity MO was measured as a function of output power. Spectra were measured by a 2MHz Cal Sensors 256 element PbSe linear detector array coupled to the exit slit of a 750 mm Acton Research Corporation monochromator.. This system was calibrated and optimized using a Yokogawa 735305 optical spectrum analyzer (OSA) and a 150 W IPG Tm fiber laser. The OSA showed a 0.2 nm linewidth for the 150 W IPG laser and after proper positioning of the array at the focal plane and adjustment of the monochromator slit widths, similar resolution was achieved with the spectrometer system. Figure 5
Fig. 5 Output spectrum of free-running Lb-cavity as a function of output power showing a shift to higher wavelengths at increased power.
shows that the width of the collection of output peaks of the laser is not a function of pump power, however, the weighted average wavelength increases with pump power, going from 2415 to 2442 nm. There are a number of thermal effects which could be postulated to shift the average output wavelength in either direction, but it is difficult to predict which will dominate. A shift to the longer wavelengths could be due to higher temperatures in the crystal affecting non-radiative transitions for higher energy levels.

Representative tunable output characteristics of the amplified, grating equipped Z-cavity are shown in Fig. 6
Fig. 6 Tunable output power of Z-cavity over 400 nm which was limited by mirror reflectivities and grating efficiency.
. A maximum power of 8.9 W was achieved at 2450 nm with tunable lasing over the 2275-2700 nm range, which was limited by grating efficiency and wavelength-dependent coating reflectivity. Figure 6 shows the dependence of the measured output power on wavelength. The linewidths at all measured points were less than 2 nm.

One of the goals of the MOPA configuration is an improvement in the beam quality for a given output power. The need for this can be understood by looking at the near-field beam profile of the MO output. Figure 7
Fig. 7 Single-frame excerpt (left) from video showing near-field beam profile changes of Lb-cavity as a function of decreasing pump power. (Media 1) starts with maximum pump power and ends at zero pump power. Transitions between different modes cause instability in power output (right).
shows a single-frame excerpt from a video showing the near-field beam profile of the Lb-cavity as a function of decreasing pump power. The cavity will run stable in one mode until the power changes enough to allow or cause a shift to a new mode. This type of transition period in the cavity is marked by unstable and fluctuating output powers and beam quality. On the other hand, with a MOPA system, the MO could be placed in a stable region while the system power output is varied by the PA, allowing for more stable overall output power and quality.

The ability of the MOPA system to achieve higher output powers while maintaining beam quality was tested by measuring the M2 of the La-cavity. At 1 W, the cavity had an M2 of 1.2 and at 3 W it had an M2 of 1.8. With the MO running at 1 W and amplified to 3 W with the PA, the system had an M2 of 1.3. This reinforces the idea that a MOPA system can be used to power scale a system where other issues may limit oscillator operation.

5. Conclusion

In conclusion, we have demonstrated a CW Cr2+:ZnSe MOPA laser with output power of 14 W and amplifier gain of 2X. We developed an amplifier model for co-linearly pumped Cr2+:ZnSe, which compares well with our experimental data. Use of a MOPA configuration allowed us to demonstrate high-power and good beam quality in a Cr2+:ZnSe laser. In addition, we demonstrated single-knob tunability at multi-watt powers over a 400 nm tuning range.

As is common with chromium-doped II-VI lasers, thermal effects limited the output power and beam quality of this setup. Improvements in cooling are needed to take full advantage of the available pump power and increase system stability. This MOPA system will be evaluated with additional MO configurations to study the optimal operating conditions and increase output laser power. Thermal management techniques will continue to be improved in an effort to reduce thermal instability in the oscillator. Improvements will also be made to the model to incorporate thermal lens modeling and effects.

Acknowledgements

The authors would like to thank S. Mirov, V. Fedorov and I. Moskalev (University of Alabama – Birmingham) for extensive discussions on modeling the nature of Cr2+ as well as experimental collaboration. The authors would also like to acknowledge their colleagues and collaborators P. Powers (University of Dayton), T. Wagner, R. Bedford, R. Peterson, J. Evans, C. Phelps, S. Hegde and J. McCurdy (Air Force Research Lab) as well as funding support by the Air Force Office of Scientific Research and the Sensors Directorate of the Air Force Research Laboratory.

References and links

1.

L. D. DeLoach, R. H. Page, G. D. Wilke, S. A. Payne, and W. F. Krupke, “Transition metal-doped zinc chalcogenides: spectroscopy and laser demonstration of a new class of gain media,” IEEE J. Quantum Electron. 32(6), 885–895 (1996). [CrossRef]

2.

R. H. Page, K. I. Schaffers, L. D. DeLoach, G. D. Wilke, F. D. Patel, J. B. Tassano Jr, S. A. Payne, W. F. Krupke, K. T. Chen, and A. Burger, “Cr2+-doped zinc chalcogenides as efficient, widely tunable mid-infrared lasers,” IEEE J. Quantum Electron. 33(4), 609–619 (1997). [CrossRef]

3.

I. T. Sorokina, E. Sorokin, S. Mirov, V. Fedorov, V. Badikov, V. Panyutin, and K. I. Schaffers, “Broadly tunable compact continuous-wave Cr2+:ZnS laser,” Opt. Lett. 27(12), 1040–1042 (2002). [CrossRef]

4.

U. Hömmerich, X. Wu, V. R. Davis, S. B. Trivedi, K. Grasza, R. J. Chen, and S. Kutcher, “Demonstration of room-temperature laser action at 2.5 mum from Cr2+:Cd0.85Mn0.15Te,” Opt. Lett. 22(15), 1180–1182 (1997). [CrossRef] [PubMed]

5.

J. McKay, K. L. Schepler, and G. C. Catella, “Efficient grating-tuned mid-infrared Cr2+:CdSe laser,” Opt. Lett. 24(22), 1575–1577 (1999). [CrossRef]

6.

U. Demirbas and A. Sennaroglu, “Intracavity-pumped Cr2+:ZnSe laser with ultrabroad tuning range between 1880 and 3100 nm,” Opt. Lett. 31(15), 2293–2295 (2006). [CrossRef] [PubMed]

7.

I. T. Sorokina, “Cr2+-doped II-VI materials for lasers and nonlinear optics,” Opt. Mater. 26(4), 395–412 (2004). [CrossRef]

8.

I. S. Moskalev, V. V. Fedorov, S. B. Mirov, P. A. Berry, and K. L. Schepler, “12-Watt CW Polycrystalline Cr2+:ZnSe Laser Pumped by Tm-fiber Laser,” in Advanced Solid State Photonics(Optical Society of America, Denver, CO, 2008), p. WB30.

9.

T. J. Carrig, G. J. Wagner, W. J. Alford, and A. Zakel, “Chromium-doped chalcogenide lasers,” in Solid State Lasers and Amplifiers, A. Sennaroglu, J. G. Fujimoto, and C. R. Pollock, eds. (SPIE, Bellingham, WA, 2004), pp. 74–82.

10.

G. J. Wagner, B. G. Tiemann, W. J. Alford, and T. J. Carrig, “Single-Frequency Cr:ZnSe Laser,” in Advanced Solid-State Photonics(Optical Society of America, 2004), p. WB12.

11.

E. Sorokin, I. T. Sorokina, M. S. Mirov, V. V. Fedorov, I. S. Moskalev, and S. B. Mirov, “Ultrabroad Continuous-Wave Tuning of Ceramic Cr:ZnSe and Cr:ZnS Lasers,” in Advanced Solid-State Photonics(Optical Society of America, 2010), p. AMC2.

12.

I. S. Moskalev, V. V. Fedorov, and S. B. Mirov, “10-watt, pure continuous-wave, polycrystalline Cr2+:ZnS laser,” Opt. Express 17(4), 2048–2056 (2009). [CrossRef] [PubMed]

13.

R. J. Harris, G. T. Johnston, G. A. Kepple, P. C. Krok, and H. Mukai, “Infrared thermooptic coefficient measurement of polycrystalline ZnSe, ZnS, CdTe, CaF2, and BaF2, single crystal KCI, and TI-20 glass,” Appl. Opt. 16(2), 436–438 (1977). [CrossRef] [PubMed]

14.

D. M. Simanovskii, H. A. Schwettman, H. Lee, and A. J. Welch, “Midinfrared Optical Breakdown in Transparent Dielectrics,” Phys. Rev. Lett. 91(10), 107601 (2003). [CrossRef] [PubMed]

15.

K. L. Schepler, R. D. Peterson, P. A. Berry, and J. B. McKay, “Thermal Effects in Cr2+:ZnSe Thin Disk Lasers,” IEEE J. Sel. Top. Quantum Electron. 11(3), 713–720 (2005). [CrossRef]

16.

P. A. Berry, and K. L. Schepler, “Cr2+:ZnSe master oscillator / power amplifier for improved power scaling,” in Solid State Lasers XIX: Technology and Devices(SPIE, San Francisco, California, USA, 2010), pp. 75781L–75711.

17.

A. Sennaroglu, U. Demirbas, A. Kurt, and M. Somer, “Concentration dependence of fluorescence and lasing efficiency in Cr2+:ZnSe lasers,” Opt. Mater. 29(6), 703–708 (2007). [CrossRef]

18.

H. Kogelnik, E. Ippen, A. Dienes, and C. Shank, “Astigmatically compensated cavities for CW dye lasers,” IEEE J. Quantum Electron. 8(3), 373–379 (1972). [CrossRef]

OCIS Codes
(140.3070) Lasers and laser optics : Infrared and far-infrared lasers
(140.3580) Lasers and laser optics : Lasers, solid-state

ToC Category:
Lasers and Laser Optics

History
Original Manuscript: March 30, 2010
Revised Manuscript: June 14, 2010
Manuscript Accepted: June 23, 2010
Published: June 30, 2010

Citation
P. A. Berry and K. L. Schepler, "High-power, widely-tunable Cr2+:ZnSe
master oscillator power amplifier systems," Opt. Express 18, 15062-15072 (2010)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-18-14-15062


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. L. D. DeLoach, R. H. Page, G. D. Wilke, S. A. Payne, and W. F. Krupke, “Transition metal-doped zinc chalcogenides: spectroscopy and laser demonstration of a new class of gain media,” IEEE J. Quantum Electron. 32(6), 885–895 (1996). [CrossRef]
  2. R. H. Page, K. I. Schaffers, L. D. DeLoach, G. D. Wilke, F. D. Patel, J. B. Tassano, S. A. Payne, W. F. Krupke, K. T. Chen, and A. Burger, “Cr2+-doped zinc chalcogenides as efficient, widely tunable mid-infrared lasers,” IEEE J. Quantum Electron. 33(4), 609–619 (1997). [CrossRef]
  3. I. T. Sorokina, E. Sorokin, S. Mirov, V. Fedorov, V. Badikov, V. Panyutin, and K. I. Schaffers, “Broadly tunable compact continuous-wave Cr2+:ZnS laser,” Opt. Lett. 27(12), 1040–1042 (2002). [CrossRef]
  4. U. Hömmerich, X. Wu, V. R. Davis, S. B. Trivedi, K. Grasza, R. J. Chen, and S. Kutcher, “Demonstration of room-temperature laser action at 2.5 mum from Cr2+:Cd0.85Mn0.15Te,” Opt. Lett. 22(15), 1180–1182 (1997). [CrossRef] [PubMed]
  5. J. McKay, K. L. Schepler, and G. C. Catella, “Efficient grating-tuned mid-infrared Cr2+:CdSe laser,” Opt. Lett. 24(22), 1575–1577 (1999). [CrossRef]
  6. U. Demirbas and A. Sennaroglu, “Intracavity-pumped Cr2+:ZnSe laser with ultrabroad tuning range between 1880 and 3100 nm,” Opt. Lett. 31(15), 2293–2295 (2006). [CrossRef] [PubMed]
  7. I. T. Sorokina, “Cr2+-doped II-VI materials for lasers and nonlinear optics,” Opt. Mater. 26(4), 395–412 (2004). [CrossRef]
  8. I. S. Moskalev, V. V. Fedorov, S. B. Mirov, P. A. Berry, and K. L. Schepler, “12-Watt CW Polycrystalline Cr2+:ZnSe Laser Pumped by Tm-fiber Laser,” in Advanced Solid State Photonics(Optical Society of America, Denver, CO, 2008), p. WB30.
  9. T. J. Carrig, G. J. Wagner, W. J. Alford, and A. Zakel, “Chromium-doped chalcogenide lasers,” in Solid State Lasers and Amplifiers, A. Sennaroglu, J. G. Fujimoto, and C. R. Pollock, eds. (SPIE, Bellingham, WA, 2004), pp. 74–82.
  10. G. J. Wagner, B. G. Tiemann, W. J. Alford, and T. J. Carrig, “Single-Frequency Cr:ZnSe Laser,” in Advanced Solid-State Photonics(Optical Society of America, 2004), p. WB12.
  11. E. Sorokin, I. T. Sorokina, M. S. Mirov, V. V. Fedorov, I. S. Moskalev, and S. B. Mirov, “Ultrabroad Continuous-Wave Tuning of Ceramic Cr:ZnSe and Cr:ZnS Lasers,” in Advanced Solid-State Photonics(Optical Society of America, 2010), p. AMC2.
  12. I. S. Moskalev, V. V. Fedorov, and S. B. Mirov, “10-watt, pure continuous-wave, polycrystalline Cr2+:ZnS laser,” Opt. Express 17(4), 2048–2056 (2009). [CrossRef] [PubMed]
  13. R. J. Harris, G. T. Johnston, G. A. Kepple, P. C. Krok, and H. Mukai, “Infrared thermooptic coefficient measurement of polycrystalline ZnSe, ZnS, CdTe, CaF2, and BaF2, single crystal KCI, and TI-20 glass,” Appl. Opt. 16(2), 436–438 (1977). [CrossRef] [PubMed]
  14. D. M. Simanovskii, H. A. Schwettman, H. Lee, and A. J. Welch, “Midinfrared Optical Breakdown in Transparent Dielectrics,” Phys. Rev. Lett. 91(10), 107601 (2003). [CrossRef] [PubMed]
  15. K. L. Schepler, R. D. Peterson, P. A. Berry, and J. B. McKay, “Thermal Effects in Cr2+:ZnSe Thin Disk Lasers,” IEEE J. Sel. Top. Quantum Electron. 11(3), 713–720 (2005). [CrossRef]
  16. P. A. Berry, and K. L. Schepler, “Cr2+:ZnSe master oscillator / power amplifier for improved power scaling,” in Solid State Lasers XIX: Technology and Devices(SPIE, San Francisco, California, USA, 2010), pp. 75781L–75711.
  17. A. Sennaroglu, U. Demirbas, A. Kurt, and M. Somer, “Concentration dependence of fluorescence and lasing efficiency in Cr2+:ZnSe lasers,” Opt. Mater. 29(6), 703–708 (2007). [CrossRef]
  18. H. Kogelnik, E. Ippen, A. Dienes, and C. Shank, “Astigmatically compensated cavities for CW dye lasers,” IEEE J. Quantum Electron. 8(3), 373–379 (1972). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Multimedia

Multimedia FilesRecommended Software
» Media 1: AVI (1732 KB)      QuickTime

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited