OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 18, Iss. 15 — Jul. 19, 2010
  • pp: 15618–15623
« Show journal navigation

Demonstration of a low VπL modulator with GHz bandwidth based on electro-optic polymer-clad silicon slot waveguides

R. Ding, T. Baehr-Jones, Y. Liu, R. Bojko, J. Witzens, S. Huang, J. Luo, S. Benight, P. Sullivan, J-M Fedeli, M. Fournier, L. Dalton, A. Jen, and M. Hochberg  »View Author Affiliations


Optics Express, Vol. 18, Issue 15, pp. 15618-15623 (2010)
http://dx.doi.org/10.1364/OE.18.015618


View Full Text Article

Acrobat PDF (811 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We demonstrate a near-infrared electro-optic modulator with a bandwidth of 3 GHz and a VπL figure of merit of 0.8 V-cm using a push-pull configuration. This is the highest operating speed achieved in a silicon-polymer hybrid system to date by several orders of magnitude. The modulator was fabricated from a silicon strip-loaded slot waveguide and clad in a nonlinear polymer. In this geometry, the electrodes form parts of the waveguide, and the modulator driving voltage drops across a 200 nm slot.

© 2010 OSA

1. Introduction

The silicon-polymer hybrid platform [1

1. T. Baehr-Jones and M. Hochberg, “Polymer Silicon Hybrid Systems: A Platform for Practical Nonlinear Optics,” J. Phys. Chem. C 112(21), 8085–8090 (2008). [CrossRef]

3

3. C. Koos, P. Vorreau, P. Dumon, R. Baets, B. Esembeson, I. Biaggio, T. Michinobu, F. Diederich, W. Freude, and J. Leuthold, “Highly-nonlinear silicon photonics slot waveguide,” OFC 2008, PDP25 (2008).

] shows great potential for a number of applications, including building low drive-voltage modulators [4

4. T. Baehr-Jones, B. Penkov, J. Huang, P. Sullivan, J. Davies, J. Takayesu, J. Luo, T.-D. Kim, L. Dalton, A. Jen, M. Hochberg, and A. Scherer, “Nonlinear polymer-clad silicon slot waveguide modulator with a half wave voltage of 0.25 V,” Appl. Phys. Lett. 92(16), 163303 (2008). [CrossRef]

] and high-speed all-optical switches [5

5. C. Koos, P. Vorreau, T. Vallaitis, P. Dumon, W. Bogaerts, R. Baets, B. Esembeson, I. Biaggio, T. Michinobu, F. Diederich, W. Freude, and J. Leuthold, “All-optical high-speed signal processing with silicon organic hybrid slot waveguides,” Nat. Photonics 3(4), 216–219 (2009). [CrossRef]

]. Recently, a slot-waveguide [6

6. V. R. Almeida, Q. F. Xu, C. A. Barrios, and M. Lipson, “Guiding and confining light in void nanostructure,” Opt. Lett. 29(11), 1209–1211 (2004). [CrossRef] [PubMed]

] based silicon waveguide clad in an electro-optic polymer has been used to build a modulator with a Vπ of 0.25 V [4

4. T. Baehr-Jones, B. Penkov, J. Huang, P. Sullivan, J. Davies, J. Takayesu, J. Luo, T.-D. Kim, L. Dalton, A. Jen, M. Hochberg, and A. Scherer, “Nonlinear polymer-clad silicon slot waveguide modulator with a half wave voltage of 0.25 V,” Appl. Phys. Lett. 92(16), 163303 (2008). [CrossRef]

], approximately a factor of 20 lower than a typical commercial modulator [7

7. Mach-40 intensity modulator http://www.covega.com

]. Photonic crystal – slot waveguide hybrid devices have also been demonstrated [8

8. J. Wülbern, J. Hampe, A. Petrov, M. Eich, J. Luo, A. Jen, A. Falco, T. Krauss, and J. Bruns, “Electro-optic modulation in slotted resonant photonic crystal heterostructures,” Appl. Phys. Lett. 94(24), 241107 (2009). [CrossRef]

]. However, in all cases, the results have been at slow speeds, on the order of 1 kHz.

All-silicon-based electro-optic modulators rely on the modulation of charge density, in which the process of carrier injection and removal limits the speed [9

9. A. Liu, R. Jones, L. Liao, D. Samara-Rubio, D. Rubin, O. Cohen, R. Nicolaescu, and M. Paniccia, “A high-speed silicon optical modulator based on a metal-oxide-semiconductor capacitor,” Nature 427(6975), 615–618 (2004). [CrossRef] [PubMed]

]. However, the second-order nonlinear moment of electro-optic polymers is believed to be ultrafast [10

10. T. Baehr-Jones, M. Hochberg, G. Wang, R. Lawson, Y. Liao, P. Sullivan, L. Dalton, A. Jen, and A. Scherer, “Optical modulation and detection in slotted Silicon waveguides,” Opt. Express 13(14), 5216–5226 (2005). [CrossRef] [PubMed]

], and modulators that can operate at frequencies higher than 100 GHz have in fact already been demonstrated [11

11. D. Chen, H. R. Fetterman, A. Chen, W. H. Steier, L. R. Dalton, W. Wang, and Y. Shi, “Demonstration of 110 GHz electro-optic polymer modulators,” Appl. Phys. Lett. 70(25), 3335–3337 (1997). [CrossRef]

,12

12. M. Lee, H. E. Katz, C. Erben, D. M. Gill, P. Gopalan, J. D. Heber, and D. J. McGee, “Broadband modulation of light by using an electro-optic polymer,” Science 298(5597), 1401–1403 (2002). [CrossRef] [PubMed]

]. For polymer-silicon hybrid systems, the silicon contacts only act as transparent electrodes, and so carrier drift velocities are not a fundamental limitation. There is therefore the potential that polymer-silicon modulators could perform at speeds not only on the order of 10 GHz, but could eventually perform at speeds in the 100 GHz regime or higher [13

13. J. Witzens, T. Baehr-Jones, and M. Hochberg, “Design of transmission line driven slot waveguide Mach-Zehnder interferometers and application to analog optical links,” Opt. Express (to be published). [PubMed]

]. But to our knowledge no high-speed electro-optic modulation results have yet been shown in silicon–polymer hybrid system.

Here, we demonstrate a polymer-clad silicon slot waveguide that can work in the gigahertz regime. Our device is relatively short, at only 1 mm, and so the Vπ is relatively large at 8 V. The VπL figure of merit for this modulator is 1.6 V-cm (single-ended), and 0.8 V-cm (push-pull) [14

14. S. J. Spector, M. W. Geis, G.-R. Zhou, M. E. Grein, F. Gan, M. A. Popovic, J. U. Yoon, D. M. Lennon, E. P. Ippen, F. Z. Kärtner, and T. M. Lyszczarz, “CMOS-compatible dual-output silicon modulator for analog signal processing,” Opt. Express 16(15), 11027–11031 (2008). [CrossRef] [PubMed]

,15

15. D. Gill, S. Patel, M. Rasras, K.-Y. Tu, A. White, Y.-K. Chen, A. Pomerene, D. Carothers, R. Kamocsai, C. Hill, and J. Beattie, “CMOS-Compatible Si-Ring-Assisted Mach–Zehnder Interferometer With Internal Bandwidth Equalization,” IEEE J. Quantum Electron. 16(1), 45–52 (2010). [CrossRef]

], which is within a factor of 2 of the figure of merit used achieved by the 0.25 V Vπ result [4

4. T. Baehr-Jones, B. Penkov, J. Huang, P. Sullivan, J. Davies, J. Takayesu, J. Luo, T.-D. Kim, L. Dalton, A. Jen, M. Hochberg, and A. Scherer, “Nonlinear polymer-clad silicon slot waveguide modulator with a half wave voltage of 0.25 V,” Appl. Phys. Lett. 92(16), 163303 (2008). [CrossRef]

]. This demonstrates that the same low drive voltages achieved at slow speeds are likely to eventually be realized in RF bandwidth devices.

While VπL values of 0.036 V-cm have been achieved with forward-biased p-i-n diode modulators [16

16. W. M. J. Green, M. J. Rooks, L. Sekaric, and Y. A. Vlasov, “Ultra-compact, low RF power, 10 Gb/s silicon Mach-Zehnder modulator,” Opt. Express 15(25), 17106–17113 (2007). [CrossRef] [PubMed]

], the need for a bias voltage creates a number of problems, and drives power consumption. Additionally, modulators based on this technique will likely be ill-suited for analog applications requiring high linearity. Unbiased, highly linear, Lithium-Niobate modulators are still a dominant technology for high-performance optical modulation. Silicon modulators that do not require bias, and can operate at higher speeds, have typical VπL values of 4 V-cm [17

17. L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, “40 Gbit/s silicon optical modulator for highspeed applications,” Electron. Lett. 43(22), 1196–1197 (2007). [CrossRef]

].

2. Design and fabrication

To achieve high-bandwidth modulation, low-resistance electrical contact between the slot arms and the driving electrodes must be made to avoid a large RC time constant, thus the thickness and doping of the strip-loading region are important considerations. A tradeoff between optical loss and electrical conductivity needs to be made to determine the doping concentration [18

18. R. A. Soref and B. R. Bennett, “Electrooptical effects in silicon,” IEEE J. Quantum Electron. 23(1), 123–129 (1987). [CrossRef]

]. Making the strip-loading thicker will naturally decrease the resistance in accordance with Ohm’s law, although the process of waveguide design will become more challenging.

A further consideration is the surface states that are frequently created in the course of processing silicon. For a surface terminated by a chemical oxide, the surface state density is about 1012 cm−2 [19

19. H. F. Okorn-Schmidt, “Characterization of silicon surface preparation processes for advanced gate dielectrics,” IBM J. Res. Develop. 43(3), 351–365 (1999). [CrossRef]

]. This density of surface states will “pin” the Fermi-level, depleting the near surface region, making the effective height of the arms for current flow less than the physical height of the silicon. Therefore, we chose a relatively thick strip-loading as 70 nm to accommodate various doping concentrations.

A Mach–Zehnder modulator was built using this geometry of waveguide, and the device layout is shown in Fig. 2
Fig. 2 (a) Mach-Zehnder modulator layout; (b) SEM micrograph showing the fabricated device; (c) SEM micrograph of the layout of one arm showing the region where ridge waveguide couples into strip-loaded slot waveguide and metal pads sitting on strip-loading.
. The fabrication of the slot waveguides was done with two self-aligned photolithography steps on a 193 nm stepper and two Si dry etching steps on Silicon-On-Insulator (SOI) wafers (having 220 nm thick silicon layer, 2 µm thick buried oxide layer and substrate resistivity of 10 Ω-cm). Thin thermal oxide was employed to smoothen the waveguide sidewalls [20

20. T. Baehr-Jones, Department of Electrical Engineering, University of Washington, Campus Box 352500, Seattle, WA 98195, R. Ding, Y. Liu, R. Bojko, J-M. Fedeli, and M. Hochberg are preparing a manuscript to be called “Low-Loss Strip-loaded slot waveguides in Silicon-on-Insulator.”

]. This oxide was stripped by buffered oxide etch (BOE) before metallization. The chip was uniformly 1018 cm−3 Boron doped (resistivity was anticipated as 0.04 Ω-cm) and annealed after fabrication. The metallization process was done by contact photolithography and the pads were formed by Al evaporated and lift-off process. Before polymer coating, a 10min anneal at 460 °C was performed to enhance metal-semiconductor contact since there was no contact implant step.

The AJSP-series electro-optic polymers are newly developed high-efficiency nonlinear optical materials, and their r33 values range from 50 to 200 pm/V at telecommunication wavelengths [21

21. J. Luo, X.-H. Zhou, and A. K.-Y. Jen, “Rational molecular design and supramolecular assembly of highly efficient organic electro-optic materials,” J. Mater. Chem. 19(40), 7410–7424 (2009). [CrossRef]

]. AJSP100 exhibits relatively large electro-optic activity (r33 value of ~65 pm/V at 1550 nm), low optical loss (~1 dB/cm), and good temporal and photochemical stability, and it is suitable for a broad spectrum of photonic applications. The electro-optic polymer cladding was prepared by doping AJSP100 into PMMA host and the resultant refractive index of the polymer was 1.54 at 1550 nm. A poling field of 100 V/μm and poling temperature of 103 °C were used. During the poling the center pad was set to 0 V, left pad was set to + Vpole and right pad was set to –Vpole, where Vpole = 20 V to achieve the poling field across a 200 nm slot. During modulation, the center pad was set to signal while the left and right pads were held at ground, so that the modulator was operated in a push-pull fashion.

3. Measurement results

Grating couplers were used to couple light on and off the chip [22

22. D. M. Beggs, M. Ayre, D. F. G. Gallagher, and T. F. Krauss, “Design and fabrication of high-efficiency fibre couplers for nanophotonic devices,” Microelectron. Eng. 84(5-8), 1446–1449 (2007). [CrossRef]

], which had a 3-dB bandwidth of around 35 nm. Total device insertion losses were approximately −44 dB fiber to fiber.

3.1 DC Vπ

Figure 3
Fig. 3 Transmission through the Mach–Zehnder device as a function of wavelength, for various modulator drive voltages. As can be seen, 2 V bias suggested the direction of spectrum shift, 8 V bias was slightly above Vπ voltage.
shows device transmission spectra for various DC drive voltages, which was applied to the center pad of the device while the side pads being held at ground. Because this data is for an unbalanced Mach–Zehnder with arm lengths of 1mm and 1.08 mm, there is an approximately 7 nm periodicity in the transmission as a function of wavelength. The more gradual variation is from the grating coupler bandwidth. The half-wave voltage Vπ can be roughly determined as 8 V, from the plots, which corresponds to a VπL of 0.8 V-cm. Due to the strip-loading, the optical mode was less confined as compared to that of a slot waveguide without strip-loading, and the 200 nm relatively wide slot further lowered the effective index susceptibility [23

23. M. Hochberg, T. Baehr-Jones, G. Wang, J. Huang, P. Sullivan, L. Dalton, and A. Scherer, “Towards a millivolt optical modulator with nano-slot waveguides,” Opt. Express 15(13), 8401–8410 (2007). [CrossRef] [PubMed]

], which turned out to be only 0.2 μm−1. Thus, 0.8 V-cm VπL suggested that an in-device poled r33 of 40 pm/V was achieved.

3.2 Frequency response

The unbalanced Mach-Zehnder design allow us to bias the modulator at a π/2 bias point, corresponding to 3 dB of extinction and the maximum response to a driving voltage, by setting the signal wavelength to the appropriate value. The frequency response of the device was characterized from 200 Hz to 2 GHz.

For the frequency range from 200 Hz to 100 MHz, a function generator was used to drive the modulator with a sinusoidal signal with peak-to-peak voltage of 2 V. A DC lock-in amplifier and an RF lock-in amplifier were used to characterize the signal output by the photodetector, which was a Thorlab DET01CFC. The results are shown in Fig. 4
Fig. 4 The frequency dependence of the device: 6 dB rolloff in S21 occurred around 3 GHz. The corresponding normalized S21 of 8 V Vπ is also plotted in the same axis. The inset graph shows the response from 200 MHz to 6 GHz, in which the −6 dB rolloff appears around 3 GHz.
as normalized S21. The corresponding normalized S21 of 8 V Vπ is also plotted on the same axes. The S21 measurement from each detector was renormalized as well for the detector gain and the laser power level, so as to allow direct comparisons between different measurements. Typical noise floors were at least 10 dB beneath the measurement, and often substantially lower. The noise floor during the measurement with the high-speed detector is plotted in Fig. 4. Since the high-speed photodetector only has a peak gain of 0.6 A/W, and the VNA has a lower dynamic range in low frequency band, the data taken with the high-speed photodetector is not presented for the frequency range from 100 MHz to 200 MHz due to the low signal-to-noise ratio.

From the spectrum of S21, we observed that the flatness of the response extended from DC to gigahertz range, and the absolute value of S21 corresponded very well to the value implied by 8 V Vπ. 6 dB rolloff point occurred at around 3 GHz. It should be noted that our 6 dB rolloff in S21 corresponds to a 3 dB in the optical response typically defined to characterize modulator bandwidth as used by Liu et al [9

9. A. Liu, R. Jones, L. Liao, D. Samara-Rubio, D. Rubin, O. Cohen, R. Nicolaescu, and M. Paniccia, “A high-speed silicon optical modulator based on a metal-oxide-semiconductor capacitor,” Nature 427(6975), 615–618 (2004). [CrossRef] [PubMed]

].

The capacitance of each arm can be estimated as 80 pF/m if we assume the polymer has a RF dielectric constant of 4 [13

13. J. Witzens, T. Baehr-Jones, and M. Hochberg, “Design of transmission line driven slot waveguide Mach-Zehnder interferometers and application to analog optical links,” Opt. Express (to be published). [PubMed]

]. When combined with the arm resistance, which is roughly 70 Ω from each pad to the waveguide arm (assuming fully-charged surface states, thus 10nm silicon depletion region at this doping), one would expect to see a device bandwidth on the order of 15 GHz. So, our observed bandwidth was significantly lower than the predicted value. This is less likely due to RF attenuation or velocity mismatch considering the short length of the device. One possible source of the limitation is a higher than expected resistance in the strip-loading section. Considering the buffered-oxide etching step mentioned in Section 2, the removal of passivation oxide by wet etching could generate considerably higher density of surface states in silicon as opposed to those terminated with high quality gate oxide [19

19. H. F. Okorn-Schmidt, “Characterization of silicon surface preparation processes for advanced gate dielectrics,” IBM J. Res. Develop. 43(3), 351–365 (1999). [CrossRef]

]. It is also possible that there is parasitic resistance in the metal pad contacts, which could be explained by the lack of a high dose contact implant, or could be caused by mechanical damage to the pads during poling or testing. RF coupling to the substrate is another possible source of the rolloff – the pads are large and the silicon substrate beneath the buried-oxide layer is not highly resistive. Further design and experimental work is expected to increase the bandwidth of these devices greatly.

4. Conclusion

We have presented an electro-optic modulator based on nonlinear optical polymer and strip-loaded slot waveguide, demonstrating that polymer-clad silicon slot waveguides can work in gigahertz regime while maintaining low VπL. Our measurements indicated a figure of merit VπL of 0.8 V-cm and a bandwidth of 3 GHz.

There are several options to improve the device performance. One possibility is reducing the metal to waveguide clearance; if the resistance in the strip-loaded section is the limitation, and this spacing were reduced to one third of its current value, the bandwidth would likely increase to 10 GHz, while adding very negligible optical loss according to finite-difference-time-domain simulation. Additionally, instead of heavily doping the chip uniformly, doping the waveguide lightly while doping the proximity of the waveguide heavily would decrease the optical loss, but lower the series resistance from metal contact to the waveguide. We believe that device performance can be dramatically improved, with eventual bandwidths of 100 GHz achievable in a 1 mm device [13

13. J. Witzens, T. Baehr-Jones, and M. Hochberg, “Design of transmission line driven slot waveguide Mach-Zehnder interferometers and application to analog optical links,” Opt. Express (to be published). [PubMed]

].

Acknowledgments

References and links

1.

T. Baehr-Jones and M. Hochberg, “Polymer Silicon Hybrid Systems: A Platform for Practical Nonlinear Optics,” J. Phys. Chem. C 112(21), 8085–8090 (2008). [CrossRef]

2.

J. Leuthold, W. Freude, J.-M. Brosi, R. Baets, P. Dumon, I. Biaggio, M. L. Scimeca, F. Diederich, B. Frank, and C. Koos, “Silicon Organic Hybrid Technology-A Platform for Practical Nonlinear Optics,” Proc. IEEE 97(7), 1304–1316 (2009). [CrossRef]

3.

C. Koos, P. Vorreau, P. Dumon, R. Baets, B. Esembeson, I. Biaggio, T. Michinobu, F. Diederich, W. Freude, and J. Leuthold, “Highly-nonlinear silicon photonics slot waveguide,” OFC 2008, PDP25 (2008).

4.

T. Baehr-Jones, B. Penkov, J. Huang, P. Sullivan, J. Davies, J. Takayesu, J. Luo, T.-D. Kim, L. Dalton, A. Jen, M. Hochberg, and A. Scherer, “Nonlinear polymer-clad silicon slot waveguide modulator with a half wave voltage of 0.25 V,” Appl. Phys. Lett. 92(16), 163303 (2008). [CrossRef]

5.

C. Koos, P. Vorreau, T. Vallaitis, P. Dumon, W. Bogaerts, R. Baets, B. Esembeson, I. Biaggio, T. Michinobu, F. Diederich, W. Freude, and J. Leuthold, “All-optical high-speed signal processing with silicon organic hybrid slot waveguides,” Nat. Photonics 3(4), 216–219 (2009). [CrossRef]

6.

V. R. Almeida, Q. F. Xu, C. A. Barrios, and M. Lipson, “Guiding and confining light in void nanostructure,” Opt. Lett. 29(11), 1209–1211 (2004). [CrossRef] [PubMed]

7.

Mach-40 intensity modulator http://www.covega.com

8.

J. Wülbern, J. Hampe, A. Petrov, M. Eich, J. Luo, A. Jen, A. Falco, T. Krauss, and J. Bruns, “Electro-optic modulation in slotted resonant photonic crystal heterostructures,” Appl. Phys. Lett. 94(24), 241107 (2009). [CrossRef]

9.

A. Liu, R. Jones, L. Liao, D. Samara-Rubio, D. Rubin, O. Cohen, R. Nicolaescu, and M. Paniccia, “A high-speed silicon optical modulator based on a metal-oxide-semiconductor capacitor,” Nature 427(6975), 615–618 (2004). [CrossRef] [PubMed]

10.

T. Baehr-Jones, M. Hochberg, G. Wang, R. Lawson, Y. Liao, P. Sullivan, L. Dalton, A. Jen, and A. Scherer, “Optical modulation and detection in slotted Silicon waveguides,” Opt. Express 13(14), 5216–5226 (2005). [CrossRef] [PubMed]

11.

D. Chen, H. R. Fetterman, A. Chen, W. H. Steier, L. R. Dalton, W. Wang, and Y. Shi, “Demonstration of 110 GHz electro-optic polymer modulators,” Appl. Phys. Lett. 70(25), 3335–3337 (1997). [CrossRef]

12.

M. Lee, H. E. Katz, C. Erben, D. M. Gill, P. Gopalan, J. D. Heber, and D. J. McGee, “Broadband modulation of light by using an electro-optic polymer,” Science 298(5597), 1401–1403 (2002). [CrossRef] [PubMed]

13.

J. Witzens, T. Baehr-Jones, and M. Hochberg, “Design of transmission line driven slot waveguide Mach-Zehnder interferometers and application to analog optical links,” Opt. Express (to be published). [PubMed]

14.

S. J. Spector, M. W. Geis, G.-R. Zhou, M. E. Grein, F. Gan, M. A. Popovic, J. U. Yoon, D. M. Lennon, E. P. Ippen, F. Z. Kärtner, and T. M. Lyszczarz, “CMOS-compatible dual-output silicon modulator for analog signal processing,” Opt. Express 16(15), 11027–11031 (2008). [CrossRef] [PubMed]

15.

D. Gill, S. Patel, M. Rasras, K.-Y. Tu, A. White, Y.-K. Chen, A. Pomerene, D. Carothers, R. Kamocsai, C. Hill, and J. Beattie, “CMOS-Compatible Si-Ring-Assisted Mach–Zehnder Interferometer With Internal Bandwidth Equalization,” IEEE J. Quantum Electron. 16(1), 45–52 (2010). [CrossRef]

16.

W. M. J. Green, M. J. Rooks, L. Sekaric, and Y. A. Vlasov, “Ultra-compact, low RF power, 10 Gb/s silicon Mach-Zehnder modulator,” Opt. Express 15(25), 17106–17113 (2007). [CrossRef] [PubMed]

17.

L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, “40 Gbit/s silicon optical modulator for highspeed applications,” Electron. Lett. 43(22), 1196–1197 (2007). [CrossRef]

18.

R. A. Soref and B. R. Bennett, “Electrooptical effects in silicon,” IEEE J. Quantum Electron. 23(1), 123–129 (1987). [CrossRef]

19.

H. F. Okorn-Schmidt, “Characterization of silicon surface preparation processes for advanced gate dielectrics,” IBM J. Res. Develop. 43(3), 351–365 (1999). [CrossRef]

20.

T. Baehr-Jones, Department of Electrical Engineering, University of Washington, Campus Box 352500, Seattle, WA 98195, R. Ding, Y. Liu, R. Bojko, J-M. Fedeli, and M. Hochberg are preparing a manuscript to be called “Low-Loss Strip-loaded slot waveguides in Silicon-on-Insulator.”

21.

J. Luo, X.-H. Zhou, and A. K.-Y. Jen, “Rational molecular design and supramolecular assembly of highly efficient organic electro-optic materials,” J. Mater. Chem. 19(40), 7410–7424 (2009). [CrossRef]

22.

D. M. Beggs, M. Ayre, D. F. G. Gallagher, and T. F. Krauss, “Design and fabrication of high-efficiency fibre couplers for nanophotonic devices,” Microelectron. Eng. 84(5-8), 1446–1449 (2007). [CrossRef]

23.

M. Hochberg, T. Baehr-Jones, G. Wang, J. Huang, P. Sullivan, L. Dalton, and A. Scherer, “Towards a millivolt optical modulator with nano-slot waveguides,” Opt. Express 15(13), 8401–8410 (2007). [CrossRef] [PubMed]

OCIS Codes
(040.6040) Detectors : Silicon
(060.4080) Fiber optics and optical communications : Modulation
(130.0130) Integrated optics : Integrated optics
(130.2790) Integrated optics : Guided waves
(130.3120) Integrated optics : Integrated optics devices
(160.5470) Materials : Polymers

ToC Category:
Integrated Optics

History
Original Manuscript: May 17, 2010
Revised Manuscript: June 28, 2010
Manuscript Accepted: June 28, 2010
Published: July 8, 2010

Citation
R. Ding, T. Baehr-Jones, Y. Liu, R. Bojko, J. Witzens, S. Huang, J. Luo, S. Benight, P. Sullivan, J-M Fedeli, M. Fournier, L. Dalton, A. Jen, and M. Hochberg, "Demonstration of a low VπL modulator with GHz bandwidth based on electro-optic 
polymer-clad silicon slot waveguides," Opt. Express 18, 15618-15623 (2010)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-18-15-15618


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. T. Baehr-Jones and M. Hochberg, “Polymer Silicon Hybrid Systems: A Platform for Practical Nonlinear Optics,” J. Phys. Chem. C 112(21), 8085–8090 (2008). [CrossRef]
  2. J. Leuthold, W. Freude, J.-M. Brosi, R. Baets, P. Dumon, I. Biaggio, M. L. Scimeca, F. Diederich, B. Frank, and C. Koos, “Silicon Organic Hybrid Technology-A Platform for Practical Nonlinear Optics,” Proc. IEEE 97(7), 1304–1316 (2009). [CrossRef]
  3. C. Koos, P. Vorreau, P. Dumon, R. Baets, B. Esembeson, I. Biaggio, T. Michinobu, F. Diederich, W. Freude, and J. Leuthold, “Highly-nonlinear silicon photonics slot waveguide,” OFC 2008, PDP25 (2008).
  4. T. Baehr-Jones, B. Penkov, J. Huang, P. Sullivan, J. Davies, J. Takayesu, J. Luo, T.-D. Kim, L. Dalton, A. Jen, M. Hochberg, and A. Scherer, “Nonlinear polymer-clad silicon slot waveguide modulator with a half wave voltage of 0.25 V,” Appl. Phys. Lett. 92(16), 163303 (2008). [CrossRef]
  5. C. Koos, P. Vorreau, T. Vallaitis, P. Dumon, W. Bogaerts, R. Baets, B. Esembeson, I. Biaggio, T. Michinobu, F. Diederich, W. Freude, and J. Leuthold, “All-optical high-speed signal processing with silicon organic hybrid slot waveguides,” Nat. Photonics 3(4), 216–219 (2009). [CrossRef]
  6. V. R. Almeida, Q. F. Xu, C. A. Barrios, and M. Lipson, “Guiding and confining light in void nanostructure,” Opt. Lett. 29(11), 1209–1211 (2004). [CrossRef] [PubMed]
  7. Mach-40 intensity modulator http://www.covega.com
  8. J. Wülbern, J. Hampe, A. Petrov, M. Eich, J. Luo, A. Jen, A. Falco, T. Krauss, and J. Bruns, “Electro-optic modulation in slotted resonant photonic crystal heterostructures,” Appl. Phys. Lett. 94(24), 241107 (2009). [CrossRef]
  9. A. Liu, R. Jones, L. Liao, D. Samara-Rubio, D. Rubin, O. Cohen, R. Nicolaescu, and M. Paniccia, “A high-speed silicon optical modulator based on a metal-oxide-semiconductor capacitor,” Nature 427(6975), 615–618 (2004). [CrossRef] [PubMed]
  10. T. Baehr-Jones, M. Hochberg, G. Wang, R. Lawson, Y. Liao, P. Sullivan, L. Dalton, A. Jen, and A. Scherer, “Optical modulation and detection in slotted Silicon waveguides,” Opt. Express 13(14), 5216–5226 (2005). [CrossRef] [PubMed]
  11. D. Chen, H. R. Fetterman, A. Chen, W. H. Steier, L. R. Dalton, W. Wang, and Y. Shi, “Demonstration of 110 GHz electro-optic polymer modulators,” Appl. Phys. Lett. 70(25), 3335–3337 (1997). [CrossRef]
  12. M. Lee, H. E. Katz, C. Erben, D. M. Gill, P. Gopalan, J. D. Heber, and D. J. McGee, “Broadband modulation of light by using an electro-optic polymer,” Science 298(5597), 1401–1403 (2002). [CrossRef] [PubMed]
  13. J. Witzens, T. Baehr-Jones, and M. Hochberg, “Design of transmission line driven slot waveguide Mach-Zehnder interferometers and application to analog optical links,” Opt. Express (to be published). [PubMed]
  14. S. J. Spector, M. W. Geis, G.-R. Zhou, M. E. Grein, F. Gan, M. A. Popovic, J. U. Yoon, D. M. Lennon, E. P. Ippen, F. Z. Kärtner, and T. M. Lyszczarz, “CMOS-compatible dual-output silicon modulator for analog signal processing,” Opt. Express 16(15), 11027–11031 (2008). [CrossRef] [PubMed]
  15. D. Gill, S. Patel, M. Rasras, K.-Y. Tu, A. White, Y.-K. Chen, A. Pomerene, D. Carothers, R. Kamocsai, C. Hill, and J. Beattie, “CMOS-Compatible Si-Ring-Assisted Mach–Zehnder Interferometer With Internal Bandwidth Equalization,” IEEE J. Quantum Electron. 16(1), 45–52 (2010). [CrossRef]
  16. W. M. J. Green, M. J. Rooks, L. Sekaric, and Y. A. Vlasov, “Ultra-compact, low RF power, 10 Gb/s silicon Mach-Zehnder modulator,” Opt. Express 15(25), 17106–17113 (2007). [CrossRef] [PubMed]
  17. L. Liao, A. Liu, D. Rubin, J. Basak, Y. Chetrit, H. Nguyen, R. Cohen, N. Izhaky, and M. Paniccia, “40 Gbit/s silicon optical modulator for highspeed applications,” Electron. Lett. 43(22), 1196–1197 (2007). [CrossRef]
  18. R. A. Soref and B. R. Bennett, “Electrooptical effects in silicon,” IEEE J. Quantum Electron. 23(1), 123–129 (1987). [CrossRef]
  19. H. F. Okorn-Schmidt, “Characterization of silicon surface preparation processes for advanced gate dielectrics,” IBM J. Res. Develop. 43(3), 351–365 (1999). [CrossRef]
  20. T. Baehr-Jones, Department of Electrical Engineering, University of Washington, Campus Box 352500, Seattle, WA 98195, R. Ding, Y. Liu, R. Bojko, J-M. Fedeli, and M. Hochberg are preparing a manuscript to be called “Low-Loss Strip-loaded slot waveguides in Silicon-on-Insulator.”
  21. J. Luo, X.-H. Zhou, and A. K.-Y. Jen, “Rational molecular design and supramolecular assembly of highly efficient organic electro-optic materials,” J. Mater. Chem. 19(40), 7410–7424 (2009). [CrossRef]
  22. D. M. Beggs, M. Ayre, D. F. G. Gallagher, and T. F. Krauss, “Design and fabrication of high-efficiency fibre couplers for nanophotonic devices,” Microelectron. Eng. 84(5-8), 1446–1449 (2007). [CrossRef]
  23. M. Hochberg, T. Baehr-Jones, G. Wang, J. Huang, P. Sullivan, L. Dalton, and A. Scherer, “Towards a millivolt optical modulator with nano-slot waveguides,” Opt. Express 15(13), 8401–8410 (2007). [CrossRef] [PubMed]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1 Fig. 2 Fig. 3
 
Fig. 4
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited