OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 18, Iss. 20 — Sep. 27, 2010
  • pp: 20793–20798
« Show journal navigation

CW lasing of Ho in KLu(WO4)2 in-band pumped by a diode-pumped Tm:KLu(WO4)2 laser

Xavier Mateos, Venkatesan Jambunathan, Maria Cinta Pujol, Joan Josep Carvajal, Francesc Díaz, Magdalena Aguiló, Uwe Griebner, and Valentin Petrov  »View Author Affiliations


Optics Express, Vol. 18, Issue 20, pp. 20793-20798 (2010)
http://dx.doi.org/10.1364/OE.18.020793


View Full Text Article

Acrobat PDF (813 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We demonstrate continuous wave (CW) room temperature laser operation of the monoclinic Ho3+-doped KLu(WO4)2 crystal using a diode-pumped Tm3+:KLu(WO4)2 laser for in-band pumping. The slope efficiency achieved amounts to ~55% with respect to the absorbed power and the maximum output power of 648 mW is generated at 2078 nm.

© 2010 OSA

1. Introduction

Ho3+ (Ho) lasers operating at wavelengths slightly above 2 µm find applications in remote sensing, medical treatments and as pump sources for mid-IR OPOs [1

1. G. J. Koch, J. Y. Beyon, F. Gibert, B. W. Barnes, S. Ismail, M. Petros, P. J. Petzar, J. Yu, E. A. Modlin, K. J. Davis, and U. N. Singh, “Side-line tunable laser transmitter for differential absorption lidar measurements of CO2: design and application to atmospheric measurements,” Appl. Opt. 47(7), 944–956 (2008). [CrossRef] [PubMed]

3

3. P. A. Budni, L. A. Pomeranz, M. L. Lemons, C. A. Miller, J. R. Mosto, and E. P. Chicklis, “Efficient mid-infrared lasing using 1.9-μm-pumped Ho:YAG and ZnGeP2 optical parametric oscillators,” J. Opt. Soc. Am. B 17(5), 723–728 (2000). [CrossRef]

]. Diode-pumping of such lasers can be realized by co-doping the active material with Tm3+ (Tm) ions making profit from the well established AlGaAs laser diodes emitting around 800 nm and the energy transfer to Ho3+ ions [4

4. V. Sudesh and K. Asai, “Spectroscopic and diode-pumped-laser properties of Tm,Ho:YLF; Tm,Ho:LuLF; and Tm,Ho:LuAG crystals: a comparative study,” J. Opt. Soc. Am. B 20(9), 1829–1837 (2003). [CrossRef]

,5

5. E. Sani, A. Toncelli, M. Tonelli, N. Coluccelli, G. Galzerano, and P. Laporta, “Comparative analysis of Tm-Ho:KYF4 laser crystals,” Appl. Phys. B 81(6), 847–851 (2005). [CrossRef]

]. Such energy transfer, however, ultimately limits the overall pump efficiency while up-conversion mechanisms result in excitation of higher energy levels of Tm whose population is no longer involved in the transfer of energy to Ho. Thus, direct excitation of the upper emitting level of Ho (5I7) with a laser pump source, also known as in-band pumping or resonant pumping, remains the most promising approach for up-scaling the output power and increasing the efficiency of all-solid-state Ho-lasers emitting on the 5I75I8 transition. It ensures minimum thermal load which is essential for the quasi-three level operation scheme in order to avoid re-absorption. Although direct in-band diode-pumping of a Ho:YAG laser has been already demonstrated with (AlGaIn)(AsSb) laser diodes [6

6. K. Scholle, and P. Fuhrberg, “In-band pumping of high-power Ho:YAG lasers by laser diodes at 1.9 µm,” in Conference on Lasers and Electro-Optics CLEO’08, Technical Digest (CD) (Optical Society of America, 2008), paper CTuAA1.

], very efficient and powerful diode-pumped Tm lasers [7

7. M. Eichhorn, “Quasi-three-level solid-state lasers in the near and mid infrared based on trivalent rare earth ions,” Appl. Phys. B 93(2-3), 269–316 (2008). [CrossRef]

], including Tm-fiber lasers, offer more flexibility with respect to the spectral and spatial characteristics and are widely used for pumping Ho-lasers, e.g [3

3. P. A. Budni, L. A. Pomeranz, M. L. Lemons, C. A. Miller, J. R. Mosto, and E. P. Chicklis, “Efficient mid-infrared lasing using 1.9-μm-pumped Ho:YAG and ZnGeP2 optical parametric oscillators,” J. Opt. Soc. Am. B 17(5), 723–728 (2000). [CrossRef]

,8

8. D. Y. Shen, A. Abdolvand, L. J. Cooper, and W. A. Clarkson, “Efficient Ho:YAG laser pumped by a cladding-pumped tunable Tm:silica-fibre laser,” Appl. Phys. B 79(5), 559–561 (2004). [CrossRef]

], including intracavity pumping, e.g [9

9. S. So, J. I. Mackenzie, D. P. Shepherd, W. A. Clarkson, J. G. Betterton, E. K. Gorton, and J. A. C. Terry, “Intra-cavity side-pumped Ho:YAG laser,” Opt. Express 14(22), 10481–10487 (2006). [CrossRef] [PubMed]

].

In this work we demonstrate, for the first time to our knowledge, continuous-wave (CW) room temperature lasing of Ho3+ in a singly-doped monoclinic crystalline host belonging to the KREW family (KLuW) under in-band pumping. Stimulated emission on the 5I75I8 transition of Ho in KLuW at 2079 nm was achieved before only by flash-lamp pumping at ~110 K [14

14. A. A. Kaminskii, A. G. Petrosyan, V. A. Fedorov, S. E. Sarkisov, V. V. Ryabchenkov, A. A. Pavlyuk, V. V. Lyubchenko, and I. V. Mochalov, “Two-micron stimulated emission by crystals with Ho3+ ions, based on the transition 5I75I8,” Sov. Phys. Dokl. 26, 846–848 (1981) (Transl. from Dokl. Akad. Nauk SSSR 260, 64–67 (1981)).

], similar to the first demonstrations of Ho lasing on this transition in the other two isostructural hosts, KYW and KGdW [14

14. A. A. Kaminskii, A. G. Petrosyan, V. A. Fedorov, S. E. Sarkisov, V. V. Ryabchenkov, A. A. Pavlyuk, V. V. Lyubchenko, and I. V. Mochalov, “Two-micron stimulated emission by crystals with Ho3+ ions, based on the transition 5I75I8,” Sov. Phys. Dokl. 26, 846–848 (1981) (Transl. from Dokl. Akad. Nauk SSSR 260, 64–67 (1981)).

,15

15. A. A. Kaminskii, A. A. Pavlyuk, P. V. Klevtsov, I. F. Balashov, V. A. Berenberg, S. E. Sarkisov, V. A. Fedorov, M. V. Petrov, and V. V. Lyubchenko, “Stimulated radiation of monoclinic crystals of KY(WO4)2 and KGd(WO4)2 with Ln3+ ions,” Inorg. Mater. 13, 482–483 (1977) (transl. from Izv. Akad. Nauk. SSSR, Neorg. Mater. 13, 582–583 (1977)).

]. Note that recently the co-doped Tm,Ho:KYW laser crystal has been investigated with indirect Ti:sapphire laser pumping at 802 nm [16

16. A. A. Lagatsky, F. Fusari, S. V. Kurilchik, V. E. Kisel, A. S. Yasukevich, N. V. Kuleshov, A. A. Pavlyuk, C. T. A. Brown, and W. Sibbett, “Optical spectroscopy and efficient continuous-wave operation near 2 µm for a Tm, Ho:KYW laser crystal,” Appl. Phys. B 97(2), 321–326 (2009). [CrossRef]

]. In the present work, the pump source for the Ho:KLuW laser is a diode-pumped home-made Tm-laser based on the same host material, KLuW, and described in detail elsewhere [13

13. X. Mateos, V. Petrov, J. Liu, M. C. Pujol, U. Griebner, M. Aguiló, F. Díaz, M. Galan, and G. Viera, “Efficient 2 µm continuous-wave laser oscillation of Tm3+:KLu(WO4)2,” IEEE J. Quantum Electron. 42, 1008–1015 (2006). [CrossRef]

]. Slope efficiency of ~55% is achieved in this initial experiment with Ho:KLuW.

2. Experiment

A series of Ho-doped KLuW crystals have been grown with doping concentration ranging from 0.5 to 7.5 at. % by the Top Seeded Solution Growth method with Slow Cooling of the solution (TSSG-SC). For the growth, a platinum crucible with a diameter 50 mm and a height of 50 mm was used. The composition of the solution was 12 mol. % KLuW as solute and 88 mol. % K2W2O7 as solvent. The raw materials were K2CO3, Ho2O3, WO3 and Lu2O3 reagents from Aldrich, Fluka and Metall (with analytical grade of purity). A b-oriented KLuW was used as a seed positioned perpendicularly with respect to the solution surface.

The active elements were oriented along the three orthogonal principal optical directions as parallelepipedic samples with their faces parallel to the N m and N p directions allowing light propagation along the N g direction. Typically, we cut and polished the active elements to a thickness of 3 mm and an aperture of 3×3 mm2. They remained uncoated.

CW laser operation was studied in a near-hemispherical resonator formed by a plane pump mirror (M5 in Fig. 2
Fig. 2 Laser setup: λ/2 and P (half-wave plate and polarizer acting as attenuator), L (AR-coated lens assembly for collimation and focusing of the fiber output with f=30 mm), L1 (AR-coated collimating lens with f=150 mm), I (isolator: quarter-wave plate), L2 (AR-coated focusing lens), M3, M4 (plane bending mirrors), M1, M5 (plane pump mirrors), M2 (Tm-laser output coupler with RC=75 mm), and M6 (Ho-laser output coupler).
), antireflection (AR) coated for the pump wavelength and high-reflection (HR) coated for the laser wavelength. The output coupler series (M6) comprised several curved mirrors with 25, 50 and 75 mm radius of curvature (RC). The transmission of the output couplers used (T OC) was 1.5% and 3% in the range from 1900 to 2050 nm. This contributed to an almost double pass pumping of the Ho:KLuW crystal since 98.5% and 97% of the non-absorbed pump radiation, respectively, was retroreflected by the output coupler. Two lenses (L2) were used to pump the Ho crystals with 50 and 150 mm focal length. The active elements were mounted in a Cu holder that served as a heat sink but no active cooling was applied. They were positioned under normal incidence to the pump beam as close as possible to the plane mirror M5.

The pump source was a Tm:KLuW laser described elsewhere [13

13. X. Mateos, V. Petrov, J. Liu, M. C. Pujol, U. Griebner, M. Aguiló, F. Díaz, M. Galan, and G. Viera, “Efficient 2 µm continuous-wave laser oscillation of Tm3+:KLu(WO4)2,” IEEE J. Quantum Electron. 42, 1008–1015 (2006). [CrossRef]

]. Its output was up-scaled to 5.1 W at 1946 nm using a fiber coupled and unpolarized diode-based pump source (Lumics) whose emission at high currents was centered at 806 nm. The radiation from the Tm:KLuW laser was linearly polarized along its N m principal optical axis. After the attenuator we placed an optical isolator (I) to avoid any back coupling from the Ho-laser set-up. Since we used for this a quarter-wave plate the pump beam to the Ho-laser was circularly polarized.

3. Results and discussion

The fact that the pump beam incident onto the Ho crystal exhibited circular polarization was unimportant in our case since, as already mentioned, the absorption of the Ho:KLuW crystal at the wavelength of 1946 nm is not substantially different for the two polarizations involved. Note that according to Fig. 1, the pump absorption is quite different at the maximum near 1960 nm but the pump wavelength of 1946 nm was fixed in our case by the optimum output coupling (5%) and the natural polarization selection of the Tm:KLuW laser [13

13. X. Mateos, V. Petrov, J. Liu, M. C. Pujol, U. Griebner, M. Aguiló, F. Díaz, M. Galan, and G. Viera, “Efficient 2 µm continuous-wave laser oscillation of Tm3+:KLu(WO4)2,” IEEE J. Quantum Electron. 42, 1008–1015 (2006). [CrossRef]

]. In any case, the Ho:KLuW laser output was always linearly polarized with E//N m although the pump was not linearly polarized. This can be explained by the higher gain cross-section for this polarization as previously observed for Yb and Tm doping of the same host [11

11. V. Petrov, M. C. Pujol, X. Mateos, Ó. Silvestre, S. Rivier, M. Aguiló, R. M. Solé, J. Liu, U. Griebner, and F. Díaz, “Growth and properties of KLu(WO4)2, and novel ytterbium and thulium lasers based on this monoclinic crystalline host,” Laser & Photon. Rev. 1(2), 179–212 (2007). [CrossRef]

].

Doping concentrations of 1, 3 and 5 at. % were tested but CW laser oscillation was possible only with the 3 at. % Ho-doped KLuW sample. Too low absorption or insufficient absorption bleaching in the three-level system are thought to be the reasons for the critical concentration dependence. The Ho:KLuW laser performance with the two pump lenses available is compared in Fig. 3
Fig. 3 Output power vs. incident pump power of the Ho:KLuW laser: comparison of the two pump lenses with focal lengths of f=50 mm and f=150 mm with an RC=25 mm output coupler (T OC=1.8% @ 2078 nm).
for an output coupler with RC=25 mm and physical cavity length of 26 mm. Better mode matching at high powers and higher laser efficiency is observed for a focal length of f=150 mm. Note that for this measurement the Tm:KLuW pump laser was operated at maximum output power and the attenuator (Fig. 2) was applied to vary the pump level for the Ho:KLuW laser without affecting the pump beam characteristics. With T OC=1.8% (at the laser wavelength), the maximum output power from the Ho:KLuW laser was 648 mW at an incident pump power of 3.3 W. It should be noted that the single pass absorption of the crystal at high incident powers was only 24% and 39% for the f=50 mm and f=150 mm lenses, respectively, and slightly higher, 28% and 42%, respectively, at low incident powers. The variation of these values is indicative of absorption bleaching effects.

We also studied the influence of the radius of curvature of the output coupler of the Ho:KLuW laser and Fig. 4
Fig. 4 Dependence of the output power of the Ho:KLuW laser on the radius of curvature (RC) of its output mirror. The pump lens is f=150 mm.
shows the input-output characteristics obtained with the f=150 mm pump lens and T OC=1.8% output coupling. Note that the values for RC=25 mm (squares in Fig. 4) are the same as those shown in Fig. 3. The RC=50 and 75 mm mirrors performed equally well and slightly better than the RC=25 mm output coupler.

In all cases shown above (Figs. 3 to 5
Fig. 5 Comparison of the Ho:KLuW laser performance for T OC=1.8% and T OC=3.3%. Inset: laser spectrum centered at 2078 nm.
) the pump wavelength of the Tm laser was 1946 nm and the Ho:KLuW laser oscillated at 2078 nm. This gives a quantum defect of only ~6%. The increase of the output coupler transmission had a very weak effect on the input – output characteristics of the Ho:KLuW laser. This is illustrated in Fig. 5 where an f=150 mm pump lens is employed and two RC=50 mm output couplers are compared. The laser wavelength remained also unchanged (2078 nm). In the whole power range, the Ho:KLuW laser operated in the fundamental transversal mode due to the relatively small pump waist diameter (e.g. of the order of 30 µm as measured with the f=50 mm pump lens), which could be easily seen on an IR visualization card.

If we assume the single pass absorption of the Ho:KLuW crystal to be 24% and 39% for the f=50 and 150 mm pump lenses, respectively, the input-output characteristics with respect to the absorbed pump power are shown in Fig. 6
Fig. 6 Estimated slope efficiencies against absorbed power in the double pump pass Ho:KLuW laser using an output coupler with RC=25 mm and T OC=1.8%.
. The maximum output power of 648 mW corresponds to an absorbed pump power of 2.05 W for the f=150 mm pump lens while the laser threshold is at ~0.5 W of absorbed power. The slope efficiency in this case amounts to 54.8%. The mode matching is better with this lens. Using a pump lens with a shorter focal length (50 mm) results in lower pump threshold (~200 mW) but reduced slope efficiency. These slope efficiencies seem not limited by up-conversion losses. Note that both the slope efficiency and the output power achieved in this initial experiment exceed those recently reported with co-doped Tm,Ho:KYW although the latter were obtained with Ti:sapphire laser pumping [16

16. A. A. Lagatsky, F. Fusari, S. V. Kurilchik, V. E. Kisel, A. S. Yasukevich, N. V. Kuleshov, A. A. Pavlyuk, C. T. A. Brown, and W. Sibbett, “Optical spectroscopy and efficient continuous-wave operation near 2 µm for a Tm, Ho:KYW laser crystal,” Appl. Phys. B 97(2), 321–326 (2009). [CrossRef]

]. It should be also noted that the slope efficiency values in our case can be regarded as a lower limit since the second pump pass may have different spatial distribution.

4. Conclusion

In conclusion, the first results obtained with in-band pumping of a CW Ho:KLuW laser reveal promising potential of this new laser material operating at 2078 nm at room temperature. No thermal roll-off in the power dependence and no damage to the uncoated active element have been observed for the available pump power. Further work will be devoted to optimization of the crystal parameters (length and doping level), improvement of the overlap between the laser and pump modes using longer samples, AR-coating of the Ho:KLuW active elements, study of the tuning potential and the use of fiber-coupled diodes for in-band pumping.

Acknowledgments

The research leading to these results has received funding from the EC's Seventh Framework Programme (LASERLAB-EUROPE, grant agreement n° 228334). This work was supported by the Spanish Government under projects MAT2008-06729-C02-02/NAN and PI09/90527 and by the Catalan Authority under project2009SGR235. J. J. Carvajal acknowledges support by the Education and Science Ministry of Spain and European Social Fund under the Ramon y Cajal program, RYC2006 – 858.

References and links

1.

G. J. Koch, J. Y. Beyon, F. Gibert, B. W. Barnes, S. Ismail, M. Petros, P. J. Petzar, J. Yu, E. A. Modlin, K. J. Davis, and U. N. Singh, “Side-line tunable laser transmitter for differential absorption lidar measurements of CO2: design and application to atmospheric measurements,” Appl. Opt. 47(7), 944–956 (2008). [CrossRef] [PubMed]

2.

S. A. Pierre and D. M. Albala, “The future of lasers in urology,” World J. Urol. 25(3), 275–283 (2007). [CrossRef] [PubMed]

3.

P. A. Budni, L. A. Pomeranz, M. L. Lemons, C. A. Miller, J. R. Mosto, and E. P. Chicklis, “Efficient mid-infrared lasing using 1.9-μm-pumped Ho:YAG and ZnGeP2 optical parametric oscillators,” J. Opt. Soc. Am. B 17(5), 723–728 (2000). [CrossRef]

4.

V. Sudesh and K. Asai, “Spectroscopic and diode-pumped-laser properties of Tm,Ho:YLF; Tm,Ho:LuLF; and Tm,Ho:LuAG crystals: a comparative study,” J. Opt. Soc. Am. B 20(9), 1829–1837 (2003). [CrossRef]

5.

E. Sani, A. Toncelli, M. Tonelli, N. Coluccelli, G. Galzerano, and P. Laporta, “Comparative analysis of Tm-Ho:KYF4 laser crystals,” Appl. Phys. B 81(6), 847–851 (2005). [CrossRef]

6.

K. Scholle, and P. Fuhrberg, “In-band pumping of high-power Ho:YAG lasers by laser diodes at 1.9 µm,” in Conference on Lasers and Electro-Optics CLEO’08, Technical Digest (CD) (Optical Society of America, 2008), paper CTuAA1.

7.

M. Eichhorn, “Quasi-three-level solid-state lasers in the near and mid infrared based on trivalent rare earth ions,” Appl. Phys. B 93(2-3), 269–316 (2008). [CrossRef]

8.

D. Y. Shen, A. Abdolvand, L. J. Cooper, and W. A. Clarkson, “Efficient Ho:YAG laser pumped by a cladding-pumped tunable Tm:silica-fibre laser,” Appl. Phys. B 79(5), 559–561 (2004). [CrossRef]

9.

S. So, J. I. Mackenzie, D. P. Shepherd, W. A. Clarkson, J. G. Betterton, E. K. Gorton, and J. A. C. Terry, “Intra-cavity side-pumped Ho:YAG laser,” Opt. Express 14(22), 10481–10487 (2006). [CrossRef] [PubMed]

10.

B. M. Walsh, “Review of Tm and Ho materials: spectroscopy and lasers,” Laser Phys. 19(4), 855–866 (2009). [CrossRef]

11.

V. Petrov, M. C. Pujol, X. Mateos, Ó. Silvestre, S. Rivier, M. Aguiló, R. M. Solé, J. Liu, U. Griebner, and F. Díaz, “Growth and properties of KLu(WO4)2, and novel ytterbium and thulium lasers based on this monoclinic crystalline host,” Laser & Photon. Rev. 1(2), 179–212 (2007). [CrossRef]

12.

J. Liu, V. Petrov, X. Mateos, H. Zhang, and J. Wang, “Efficient high-power laser operation of Yb:KLu(WO4)2 crystals cut along the principal optical axes,” Opt. Lett. 32(14), 2016–2018 (2007). [CrossRef] [PubMed]

13.

X. Mateos, V. Petrov, J. Liu, M. C. Pujol, U. Griebner, M. Aguiló, F. Díaz, M. Galan, and G. Viera, “Efficient 2 µm continuous-wave laser oscillation of Tm3+:KLu(WO4)2,” IEEE J. Quantum Electron. 42, 1008–1015 (2006). [CrossRef]

14.

A. A. Kaminskii, A. G. Petrosyan, V. A. Fedorov, S. E. Sarkisov, V. V. Ryabchenkov, A. A. Pavlyuk, V. V. Lyubchenko, and I. V. Mochalov, “Two-micron stimulated emission by crystals with Ho3+ ions, based on the transition 5I75I8,” Sov. Phys. Dokl. 26, 846–848 (1981) (Transl. from Dokl. Akad. Nauk SSSR 260, 64–67 (1981)).

15.

A. A. Kaminskii, A. A. Pavlyuk, P. V. Klevtsov, I. F. Balashov, V. A. Berenberg, S. E. Sarkisov, V. A. Fedorov, M. V. Petrov, and V. V. Lyubchenko, “Stimulated radiation of monoclinic crystals of KY(WO4)2 and KGd(WO4)2 with Ln3+ ions,” Inorg. Mater. 13, 482–483 (1977) (transl. from Izv. Akad. Nauk. SSSR, Neorg. Mater. 13, 582–583 (1977)).

16.

A. A. Lagatsky, F. Fusari, S. V. Kurilchik, V. E. Kisel, A. S. Yasukevich, N. V. Kuleshov, A. A. Pavlyuk, C. T. A. Brown, and W. Sibbett, “Optical spectroscopy and efficient continuous-wave operation near 2 µm for a Tm, Ho:KYW laser crystal,” Appl. Phys. B 97(2), 321–326 (2009). [CrossRef]

17.

M. C. Pujol, C. Cascales, M. Rico, J. Massons, F. Diaz, P. Porcher, and C. Zaldo, “Measurement and crystal field analysis of energy levels of Ho3+ and Er3+ in KGd(WO4)2 single crystal,” J. Alloy. Comp. 323–324(1-2), 321–325 (2001). [CrossRef]

18.

M. C. Pujol, J. Massons, M. Aguilo, F. Diaz, M. Rico, and C. Zaldo, “Emission cross sections and spectroscopy of Ho3+ laser channels in KGd(WO4)2 single crystal,” IEEE J. Quantum Electron. 38(1), 93–100 (2002). [CrossRef]

19.

V. Jambunathan, X. Mateos, M. C. Pujol, J. J. Carvajal, J. Massons, M. Aguilo, and F. Diaz, “Near-infrared photoluminescence from Ho3+-doped monoclinic KLu(WO4)2 crystal codoped with Tm3+,” J. Lumin. 129(12), 1882–1885 (2009). [CrossRef]

OCIS Codes
(140.3070) Lasers and laser optics : Infrared and far-infrared lasers
(140.3480) Lasers and laser optics : Lasers, diode-pumped
(140.5680) Lasers and laser optics : Rare earth and transition metal solid-state lasers

ToC Category:
Lasers and Laser Optics

History
Original Manuscript: April 30, 2010
Revised Manuscript: July 5, 2010
Manuscript Accepted: August 11, 2010
Published: September 16, 2010

Citation
Xavier Mateos, Venkatesan Jambunathan, Maria Cinta Pujol, Joan Josep Carvajal, Francesc Díaz, Magdalena Aguiló, Uwe Griebner, and Valentin Petrov, "CW lasing of Ho in KLu(WO4)2 in-band pumped by a diode-pumped Tm:KLu(WO4)2 laser," Opt. Express 18, 20793-20798 (2010)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-18-20-20793


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. G. J. Koch, J. Y. Beyon, F. Gibert, B. W. Barnes, S. Ismail, M. Petros, P. J. Petzar, J. Yu, E. A. Modlin, K. J. Davis, and U. N. Singh, “Side-line tunable laser transmitter for differential absorption lidar measurements of CO2: design and application to atmospheric measurements,” Appl. Opt. 47(7), 944–956 (2008). [CrossRef] [PubMed]
  2. S. A. Pierre and D. M. Albala, “The future of lasers in urology,” World J. Urol. 25(3), 275–283 (2007). [CrossRef] [PubMed]
  3. P. A. Budni, L. A. Pomeranz, M. L. Lemons, C. A. Miller, J. R. Mosto, and E. P. Chicklis, “Efficient mid-infrared lasing using 1.9-μm-pumped Ho:YAG and ZnGeP2 optical parametric oscillators,” J. Opt. Soc. Am. B 17(5), 723–728 (2000). [CrossRef]
  4. V. Sudesh and K. Asai, “Spectroscopic and diode-pumped-laser properties of Tm,Ho:YLF; Tm,Ho:LuLF; and Tm,Ho:LuAG crystals: a comparative study,” J. Opt. Soc. Am. B 20(9), 1829–1837 (2003). [CrossRef]
  5. E. Sani, A. Toncelli, M. Tonelli, N. Coluccelli, G. Galzerano, and P. Laporta, “Comparative analysis of Tm-Ho:KYF4 laser crystals,” Appl. Phys. B 81(6), 847–851 (2005). [CrossRef]
  6. K. Scholle and P. Fuhrberg, “In-band pumping of high-power Ho:YAG lasers by laser diodes at 1.9 µm,” in Conference on Lasers and Electro-Optics CLEO’08, Technical Digest (CD) (Optical Society of America, 2008), paper CTuAA1.
  7. M. Eichhorn, “Quasi-three-level solid-state lasers in the near and mid infrared based on trivalent rare earth ions,” Appl. Phys. B 93(2-3), 269–316 (2008). [CrossRef]
  8. D. Y. Shen, A. Abdolvand, L. J. Cooper, and W. A. Clarkson, “Efficient Ho:YAG laser pumped by a cladding-pumped tunable Tm:silica-fibre laser,” Appl. Phys. B 79(5), 559–561 (2004). [CrossRef]
  9. S. So, J. I. Mackenzie, D. P. Shepherd, W. A. Clarkson, J. G. Betterton, E. K. Gorton, and J. A. C. Terry, “Intra-cavity side-pumped Ho:YAG laser,” Opt. Express 14(22), 10481–10487 (2006). [CrossRef] [PubMed]
  10. B. M. Walsh, “Review of Tm and Ho materials: spectroscopy and lasers,” Laser Phys. 19(4), 855–866 (2009). [CrossRef]
  11. V. Petrov, M. C. Pujol, X. Mateos, Ó. Silvestre, S. Rivier, M. Aguiló, R. M. Solé, J. Liu, U. Griebner, and F. Díaz, “Growth and properties of KLu(WO4)2, and novel ytterbium and thulium lasers based on this monoclinic crystalline host,” Laser & Photon. Rev. 1(2), 179–212 (2007). [CrossRef]
  12. J. Liu, V. Petrov, X. Mateos, H. Zhang, and J. Wang, “Efficient high-power laser operation of Yb:KLu(WO4)2 crystals cut along the principal optical axes,” Opt. Lett. 32(14), 2016–2018 (2007). [CrossRef] [PubMed]
  13. X. Mateos, V. Petrov, J. Liu, M. C. Pujol, U. Griebner, M. Aguiló, F. Díaz, M. Galan, and G. Viera, “Efficient 2 µm continuous-wave laser oscillation of Tm3+:KLu(WO4)2,” IEEE J. Quantum Electron. 42, 1008–1015 (2006). [CrossRef]
  14. A. A. Kaminskii, A. G. Petrosyan, V. A. Fedorov, S. E. Sarkisov, V. V. Ryabchenkov, A. A. Pavlyuk, V. V. Lyubchenko, and I. V. Mochalov, “Two-micron stimulated emission by crystals with Ho3+ ions, based on the transition 5I7→5I8,” Sov. Phys. Dokl. 26, 846–848 (1981) (Transl. from Dokl. Akad. Nauk SSSR 260, 64–67 (1981)).
  15. A. A. Kaminskii, A. A. Pavlyuk, P. V. Klevtsov, I. F. Balashov, V. A. Berenberg, S. E. Sarkisov, V. A. Fedorov, M. V. Petrov, and V. V. Lyubchenko, “Stimulated radiation of monoclinic crystals of KY(WO4)2 and KGd(WO4)2 with Ln3+ ions,” Inorg. Mater. 13, 482–483 (1977) (transl. from Izv. Akad. Nauk. SSSR, Neorg. Mater. 13, 582–583 (1977)).
  16. A. A. Lagatsky, F. Fusari, S. V. Kurilchik, V. E. Kisel, A. S. Yasukevich, N. V. Kuleshov, A. A. Pavlyuk, C. T. A. Brown, and W. Sibbett, “Optical spectroscopy and efficient continuous-wave operation near 2 µm for a Tm, Ho:KYW laser crystal,” Appl. Phys. B 97(2), 321–326 (2009). [CrossRef]
  17. M. C. Pujol, C. Cascales, M. Rico, J. Massons, F. Diaz, P. Porcher, and C. Zaldo, “Measurement and crystal field analysis of energy levels of Ho3+ and Er3+ in KGd(WO4)2 single crystal,” J. Alloy. Comp. 323–324(1-2), 321–325 (2001). [CrossRef]
  18. M. C. Pujol, J. Massons, M. Aguilo, F. Diaz, M. Rico, and C. Zaldo, “Emission cross sections and spectroscopy of Ho3+ laser channels in KGd(WO4)2 single crystal,” IEEE J. Quantum Electron. 38(1), 93–100 (2002). [CrossRef]
  19. V. Jambunathan, X. Mateos, M. C. Pujol, J. J. Carvajal, J. Massons, M. Aguilo, and F. Diaz, “Near-infrared photoluminescence from Ho3+-doped monoclinic KLu(WO4)2 crystal codoped with Tm3+,” J. Lumin. 129(12), 1882–1885 (2009). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited