OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 18, Iss. 6 — Mar. 15, 2010
  • pp: 5691–5706
« Show journal navigation

Optimal light trapping in ultra-thin photonic crystal crystalline silicon solar cells

Shrestha Basu Mallick, Mukul Agrawal, and Peter Peumans  »View Author Affiliations


Optics Express, Vol. 18, Issue 6, pp. 5691-5706 (2010)
http://dx.doi.org/10.1364/OE.18.005691


View Full Text Article

Acrobat PDF (1736 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

Crystalline silicon is an attractive photovoltaic material because of its natural abundance, accumulated materials and process knowledge, and its appropriate band gap. To reduce cost, thin films of crystalline silicon can be used. This reduces the amount of material needed and allows material with shorter carrier diffusion lengths to be used. However, the indirect band gap of silicon requires that a light trapping approach be used to maximize optical absorption. Here, a photonic crystal (PC) based approach is used to maximize solar light harvesting in a 400 nm-thick silicon layer by tuning the coupling strength of incident radiation to quasiguided modes over a broad spectral range. The structure consists of a double layer PC with the upper layer having holes which have a smaller radius compared to the holes in the lower layer. We show that the spectrally averaged fraction of photons absorbed is increased 8-fold compared to a planar cell with equivalent volume of active material. This results in an enhancement of maximum achievable photocurrent density from 7.1 mA/cm2 for an unstructured film to 21.8 mA/cm2 for a film structured as the double layer photonic crystal. This photocurrent density value approaches the limit of 26.5 mA/cm2, obtained using the Yablonovitch light trapping limit for the same volume of active material.

© 2010 OSA

1. Introduction

Crystalline Si (c-Si) is an attractive material for photovoltaic cells due to its natural abundance, nearly ideal band gap, and leverage of existing process and materials knowledge. A potential approach to significantly lower the cost of crystalline Si (c-Si) solar cells is to use thin films of Si on low-cost substrates, that are formed by the deposition of a thin film using chemical vapor deposition [1

1. K. Yamamoto, T. Suzuki, M. Yoshimi, and A. Nakaijima, “Optical Confinement effect for below 5 µm Thin Film Poly-Si Solar Cell on Glass Substrate,” Jpn. J. Appl. Phys. 36(Part 2, No. 5A), L569–L572 (1997). [CrossRef]

] or epitaxy followed by release [2

2. R. Bergmann, T. Rinke, T. Wagner, and J. Werner, “Thin film solar cells on glass based on the transfer of monocrystalline Si films,” Sol. Energy Mater. Sol. Cells 65(1-4), 355–361 (2001). [CrossRef]

,3

3. H. Tayanaka, K. Yamauchi, and T. Matsushita, “Thin-film crystalline silicon solar cells obtained by separation of a porous silicon sacrificial layer,” in Proceedings of the Second World Conference on Photovoltaic Solar Energy Conversion(1998), p. 1272.

], or, alternatively, by a mechanical step such as that used in the SLIM-cut process developed at IMEC. Using thin layers of active material also allows poorer quality Si with shorter carrier diffusion lengths to be used and minimizes Auger recombination, leading to larger open circuit voltages and fill-factors [4

4. R. M. Swanson, “Point-contact solar cells - Modeling and experiment,” Sol. Cells 17(1), 85–118 (1986). [CrossRef]

6

6. T. Tiedje, E. Yablonovitch, G. D. Cody, and B. G. Brooks, “Limiting Efficiency of Silicon Solar Cells,” IEEE Trans. Electron. Dev. 31(5), 711–716 (1984). [CrossRef]

]. Thin-film cells also have the advantage of lower energy consumption for device fabrication and offer potential for light-weight and flexible photovoltaics.

Most of the work done on thin-film Si cells has focused on cells which are microns to tens of microns thick. Relatively little work has focused on the design and fabrication of c-Si solar cells whose film thickness is in the sub-micron range. Such ultrathin c-Si cells are of interest because they further limit the amount of material needed, and allow for adequate electrical performance despite reduced carrier diffusion lengths. Danos, et al. [7

7. L. Danos, G. Jones, R. Greef, and T. Markvart, “Ultra-thin silicon solar cell: Modelling and Characterisation,” Phys. Status Solidi 5(5), 1407–1410 (2008). [CrossRef]

] designed a 200 nm-thick cell with a short-circuit current density of only 6.5 mA/cm2. Yoon, et al. [8

8. J. Yoon, A. J. Baca, S. I. Park, P. Elvikis, J. B. Geddes 3rd, L. Li, R. H. Kim, J. Xiao, S. Wang, T. H. Kim, M. J. Motala, B. Y. Ahn, E. B. Duoss, J. A. Lewis, R. G. Nuzzo, P. M. Ferreira, Y. Huang, A. Rockett, and J. A. Rogers, “Ultrathin silicon solar microcells for semitransparent, mechanically flexible and microconcentrator module designs,” Nat. Mater. 7(11), 907–915 (2008). [CrossRef] [PubMed]

] have proposed a process to make submicron cells by KOH etching of bulk wafers and transfer printing on substrates but the cells they fabricated were 15-20 μm in thickness. One of the main challenges in realizing the efficiency potential of ultrathin c-Si cells is the weak optical absorption in the near-infrared spectral range with an absorption length of just over 10 μm at λ = 800 nm to >1 mm at λ = 1108 nm.

Conventional c-Si solar cells use a texturing approach whose effects can be understood using geometric optics [9

9. E. Yablonovitch, “Statistical Ray Optics,” J. Opt. Soc. Am. 72(7), 899–907 (1982). [CrossRef]

,10

10. E. Yablonovitch and G. D. Cody, “Intensity Enhancement in Textured Optical Sheets for Solar Cells,” IEEE Trans. Electron. Dev. 29(2), 300–305 (1982). [CrossRef]

]. Strongly scattering surfaces that bound the absorbing layer randomize the direction of light internally within the absorber into a uniform distribution of forward angles, thus randomizing the occupation of the photon density-of-states (PDOS). This increases the effective absorption in a weak absorber by a factor of 4n2 (where n is the index of refraction) over that of a planar slab with the same volume [9

9. E. Yablonovitch, “Statistical Ray Optics,” J. Opt. Soc. Am. 72(7), 899–907 (1982). [CrossRef]

,10

10. E. Yablonovitch and G. D. Cody, “Intensity Enhancement in Textured Optical Sheets for Solar Cells,” IEEE Trans. Electron. Dev. 29(2), 300–305 (1982). [CrossRef]

]. This geometrical optics limit is also known as the Yablonovitch limit and corresponds to an enhancement in absorption of ~50 for c-Si for near the band edge. This is the highest enhancement that can be obtained in the geometric optics regime when angles of incidence spanning the full hemisphere are considered.

The geometric optics approach is much less effective in thin-film solar cells where the wavelength of the incident light is comparable or larger than the film thickness. The local PDOS averaged over the thickness of a thin film is significantly less than the bulk PDOS such that even for an ideal Lambertian scattering surface, the enhancement in optical path length cannot approach the Yablonovitch limit [11

11. M. Agrawal, Photonic Design for Efficient Solid-State Energy Conversion, (Stanford University, Stanford, 2008).

]. In addition, subwavelength Lambertian scattering surfaces that work across a wide spectral range are challenging to realize.

Because of the shortcomings of geometric light trapping schemes, light harvesting approaches based on wave optics in thin-film cells have attracted significant interest. It has been proposed that coherent light trapping schemes can achieve absorption enhancements superior to geometric approaches because the wave-optics approach can target a specific spectral range [12

12. J. Gee, “Optically enhanced absorption in thin silicon layers using photonic crystals,” in Twenty-Ninth IEEE Photovolt. Spec. Conf. (2002), pp. 150–153.

]. Several wave optics light-trapping approaches were explored such as surface plasmon based light-trapping [13

13. S. Pillai, K. Catchpole, T. Trupke, G. Zhang, J. Zhao, and M. A. Green, “Enhanced emission from Si-based light emitting diodes using surface plasmons,” Appl. Phys. Lett. 88(16), 161102 (2006). [CrossRef]

,14

14. D. M. Schaadt, B. Feng, and E. T. Yu, “Enhanced semiconductor optical absorption via surface plasmon excitation in metal nanoparticles,” Appl. Phys. Lett. 86(6), 063106 (2005). [CrossRef]

], scattering into guided modes by metal nanoparticles [15

15. P. N. Saeta, V. E. Ferry, D. Pacifici, J. N. Munday, and H. A. Atwater, “How much can guided modes enhance absorption in thin solar cells?” Opt. Express 17(23), 20975–20990 (2009). [CrossRef] [PubMed]

] and grating couplers [16

16. R. H. Morf, and H. Kiess, “Submicron gratings for light trapping in silicon solar cells: a theoretical study,” in Proc. Ninth Internat. Conf. Photvolt. Solar Energy, W. Palz, ed., (Commission of the European Commmunities, Brussels, 1989), pp. 313–315.

19

19. F. Llopis and I. Tobias, “The role of rear surface in thin silicon solar cells,” Sol. Energy Mater. Sol. Cells 87(1-4), 481–492 (2005). [CrossRef]

], and photonic crystals (PCs) (in 1D [20

20. Y. Park, E. Drouard, O. El Daif, X. Letartre, P. Viktorovitch, A. Fave, A. Kaminski, M. Lemiti, and C. Seassal, “Absorption enhancement using photonic crystals for silicon thin film solar cells,” Opt. Express 17(16), 14312–14321 (2009). [CrossRef] [PubMed]

24

24. J. G. Mutitu, S. Shi, C. Chen, T. Creazzo, A. Barnett, C. Honsberg, and D. W. Prather, “Thin film solar cell design based on photonic crystal and diffractive grating structures,” Opt. Express 16(19), 15238–15248 (2008). [CrossRef] [PubMed]

], 2D [21

21. D. Zhou and R. Biswas, “Photonic crystal enhanced light-trapping in thin film solar cells,” J. Appl. Phys. 103(9), 093102 (2008). [CrossRef]

,22

22. P. Bermel, C. Luo, L. Zeng, L. C. Kimerling, and J. D. Joannopoulos, “Improving thin-film crystalline silicon solar cell efficiencies with photonic crystals,” Opt. Express 15(25), 16986–17000 (2007). [CrossRef] [PubMed]

] and 3D [25

25. C. L. Huisman, J. Schoonman, and A. Goossens, “The application of inverse titania opals in nanostructured solar cells,” Sol. Energy Mater. Sol. Cells 85, 115–124 (2005).

27

27. S. Nishimura, N. Abrams, B. A. Lewis, L. I. Halaoui, T. E. Mallouk, K. D. Benkstein, J. van de Lagemaat, and A. J. Frank, “Standing wave enhancement of red absorbance and photocurrent in dye-sensitized titanium dioxide photoelectrodes coupled to photonic crystals,” J. Am. Chem. Soc. 125(20), 6306–6310 (2003). [CrossRef] [PubMed]

]). Zeng, et al. have explored c-Si cells with photonic crystals (dielectric distributed Bragg reflectors (DBR) and 1D gratings) as back reflectors [23

23. L. Zeng, Y. Yi, C. Hong, J. Liu, N. Feng, X. Duan, L. C. Kimerling, and B. A. Alamariu, “Efficiency enhancement in Si solar cells by textured photonic crystal back reflector,” Appl. Phys. Lett. 89(11), 111111 (2006). [CrossRef]

] but the observed enhancement in efficiencies was small for the thick cells they studied. The optimization of such structures for application in thin-film cells was explored by Feng, et al. [28

28. N. N. Feng, J. Michel, L. Zeng, J. Liu, C. Y. Hong, L. C. Kimerling, and X. Duan, “Design of Highly Efficient Light-Trapping Structures for Thin-Film Crystalline Silicon Solar Cells,” IEEE Trans. Electron. Dev. 54(8), 1926–1933 (2007). [CrossRef]

]. O'Brien, et al. studied the effect of a PC back reflector, demonstrating up to a 1.65 and 2.5-fold enhancement in optical absorption over a narrow spectral range near the band edge of a 10 μm thick μc-Si cell and a 250nm thick a-Si cell, respectively [29

29. P. G. O'Brien, N. P. Kherani, A. Chutinan, G. A. Ozin, S. John, and S. Zukotynski, “Silicon photovoltaics using conducting photonic crystal back-reflectors,” Adv. Mater. 20(8), 1577–1582 (2008). [CrossRef]

,30

30. P. G. O'Brien, N. P. Kherani, S. Zukotynski, G. A. Ozin, E. Vekris, N. Tetreault, A. Chutinan, S. John, A. Mihi, and H. Miguez, “Enhanced photoconductivity in thin-film semiconductors optically coupled to photonic crystals,” Adv. Mater. 19(23), 4177–4182 (2007). [CrossRef]

]. Bermel, et al. showed that 2 μm-thick c-Si cells with a back reflector consisting of a 2D PC in addition to a DBR as back reflector had superior light absorption compared to a 3D PC back reflector with a maximum enhancement in optical absorption given by a factor of nearly 5 as compared to a planar slab [22

22. P. Bermel, C. Luo, L. Zeng, L. C. Kimerling, and J. D. Joannopoulos, “Improving thin-film crystalline silicon solar cell efficiencies with photonic crystals,” Opt. Express 15(25), 16986–17000 (2007). [CrossRef] [PubMed]

]. Another interesting theoretical result is that by Chutinan et al. [31

31. A. Chutinan, N. P. Kherani, and S. Zukotynski, “High-efficiency photonic crystal solar cell architecture,” Opt. Express 17(11), 8871–8878 (2009). [CrossRef] [PubMed]

] where they showed that structuring the active region as a 2D PC increased the efficiency of 2 μm thick c-Si cells by 11.15% and 10 μm thick c-Si cells by 3.87%.

Here, we focus on ultrathin c-Si films and analyze the achievable enhancement in optical absorption across the solar spectrum by structuring the c-Si film as a 2D PC (see Fig. 1
Fig. 1 Schematic of optimized structure
). By exploring the design space using numerical simulations, we show that such structures can provide a spectrally-averaged absorption enhancement that approaches the limit derived in the geometric optics regime [9

9. E. Yablonovitch, “Statistical Ray Optics,” J. Opt. Soc. Am. 72(7), 899–907 (1982). [CrossRef]

]. This is consistent with our theoretical analysis of light trapping in the wave-optics regime that yields an upper limit for the achievable enhancement of optical absorption of 4n2, irrespective of the photonic structure that is built around the volume of interest and irrespective of the spectral range considered [11

11. M. Agrawal, Photonic Design for Efficient Solid-State Energy Conversion, (Stanford University, Stanford, 2008).

], when one integrates over all angles of incidence.

2. Simulation methods

3. Results

The structures investigated consist of a 400nm thick c-Si film. The thickness was chosen as 400 nm because the goal was to simulate an ultrathin c-Si solar cell and see how far the performance could be improved with the light trapping structures proposed. Having a submicron thickness also means that poorer quality silicon with diffusion lengths of the order of tens of microns or less can be used to make the solar cell.

A schematic of an unit cell of the structure is shown in Fig. 1 with an antireflection coating (ARC) (shown in green) on top of the active layer (shown in gray) and a 400 nm-thick SiO2 layer (shown in yellow) below the active layer. The entire structure is coated on the back with a metal layer (shown in blue) to ensure double-pass reflection. The ARC and active layers are perforated by a square lattice of cylindrical holes fashioned into a double-layer 2D PC. We considered double-layer PCs in which the hole diameter varies in two steps throughout the film thickness because this offers additional degrees of freedom in the design while still being amenable to fabrication. The fabrication involves starting with a silicon layer with the appropriate doping, etching the top layer for the smaller hole, passivating and protecting the sidewalls and then isotropically etching the larger hole in the bottom. Additional carrier recombination due to the etched surfaces in the double-layer PC structure is a potential concern. With proper passivation, the surface recombination can however be greatly reduced [39

39. A. G. Aberle, “Surface passivation of crystalline silicon solar cells: a review,” Prog. Photovoltaics 8(5), 473–487 (2000). [CrossRef]

]. Also, for these thin structures, the benefits of light trapping are far likely to outweigh the loss of efficiency due to increased surface recombination. Investigation of surface recombination and carrier collection is an important aspect that should be investigated in measurements with such patterned devices. Since this is a paper on modeling light trapping in ultra-thin silicon layers, we ignore surface recombination effects.

The geometry is fully parametrized by the period (p) and ratio of the hole diameter (d) over period (p) in the upper and lower c-Si layers. Light is incident at normal incidence from the top. Electromagnetic fields as a function of wavelength, geometry and angle of incidence are calculated using RCWA, as described above. The structure is symmetrical in the two in-plane directions to maintain polarization-independence for normal incidence. Figure 1 also shows a vertical cross-section of the same structure. It is seen that the optimized structure is a double layer PC which looks like an inverted pyramid of silicon, if two unit cells are seen side by side. It should be noted that even though Fig. 1 shows the final structure with the ARC and back reflector, all the initial simulations were done on structures without ARCs or back reflectors. The purpose was to focus on light-trapping effects due to the PC structures alone.

3.1 Convergence

Using the above method, the fraction of incident photons absorbed by the patterned structure was calculated over the spectral range 400-1200 nm with a step size of 3 nm. The accuracy of our model was tested by verifying the convergence as a function of the number of spatial harmonics. The convergence for a structure in which the upper layer has a d/p ratio of 0.65 and the lower layer a d/p ratio of 0.9 (cf. Fig. 2
Fig. 2 Simulated fraction of photons absorbed under normal incidence as a function of the number of harmonics used. The periodicity of the 2D c-Si PC was 600 nm, and the ratio d/p for the upper and lower layer was 0.9 and 0.65, respectively. Insets: Enlarged portion of the spectrum (indicated by black dashed box) and schematic of the simulated structure.
inset) was tested over the spectral range considered by evaluating the fraction of photons absorbed for normal incidence as a function of the number of harmonics used in the optical simulation, as shown in Fig. 2. When less than 200 harmonics are used the absorption values change for a given wavelength and the resonant peaks shift when the number of harmonics is increased. The absorption spectra converge when >200 harmonics are used with <1% variation in absorption. The simulations reported here were carried out using 700 harmonics. The graph is plotted on a logarithmic scale so that the difference in convergence between simulations is magnified.

3.2 Optimization with respect to period

Initially, the geometric parameters of the upper and lower PC layers were optimized to get the maximum achievable photocurrent density (MAPD) for a structure with a 100 nm-thick SiO2 ARC and without backside metal coating. As mentioned above, this was done in order to focus on light-trapping effects due to the PC structures alone. Each layer of the 2D PC was taken to span half the c-Si film thickness for the initial unoptimized structure. To calculate the MAPD, it was assumed that each absorbed photon generates an electron-hole pair and that both carriers are collected by their respective electrodes. This is a useful assumption for a thin device when the minority carrier diffusion length is much greater than the distance traveled by each of the carriers

The MAPD is a useful metric since it allows one to evaluate the effect of structuring on the optical performance. The MAPD is calculated in Eq. (1) as follows
MAPD=0dλ[eλhcdIdλα(λ)]
(1)
where dI/dλ is the light intensity incident on the solar cell per unit area per unit wavelength (the AM1.5 global tilt spectrum was used), α(λ) is the fraction of photons absorbed, e is the electron charge, h is Planck’s constant and c is the speed of light. Fig. 3
Fig. 3 MAPD as a function of period for inverted pyramidal structures. The d/p ratios of the upper and lower PC layer were optimized for maximum MAPD for each period.
shows the MAPD as a function of period for the inverted pyramidal structures (see Fig. 1). For each period, the d/p ratios of the upper and lower c-Si layers were optimized. Based on this data, it was seen that the MAPD was the highest for a period of 600 nm even though the other values were comparable.

3.3 Optimization with respect to ratio of diameter of hole over periodicity of structure

Figure 4
Fig. 4 MAPD under normal incidence as a function of d/p ratios of the upper and lower PC layers for a period of 600 nm. (The colorbar has units ofA/cm2)
shows the variation in MAPD as a function of the d/p ratios of the upper and lower PC layer for a 600 nm period. We note that optimum values of MAPD are obtained both for pyramid (d/p of lower layer < d/p of upper layer) as well as inverted pyramid (d/p of lower layer > d/p of upper layer) structures. In the remainder of this work, we focus on the inverted pyramid structures. In terms of optimal MAPD, the structure with a d/p of 0.9 for the upper layer and 0.65 for the lower layer is optimal with a MAPD of 16.9 mA/cm2.

Since the thickness of the active layer is kept constant at 400 nm, the volume of active material is different for each design in Fig. 4. The enhancement in MAPD relative to a solid slab (i.e. unstructured slab) cell with the same active layer volume as the structured layer, and a 70nm thick SiNx ARC, is shown in Fig. 5
Fig. 5 Enhancement in MAPD under normal incidence of a structured layer compared to a solid slab with the same active layer volume as the structured layer, as a function of d/p ratios of the upper and lower PC layers.
. The enhancement is more pronounced for higher d/p ratios since the equivalent solid slab is much thinner.

3.4 Optimization with respect to relative thicknesses of the two layers

In Fig. 6
Fig. 6 MAPD as a function of relative thicknesses of the two layers
, we vary the thicknesses of the two layers while keeping the total thickness and d/p ratios constant. A thickness of 250 nm for the upper layer and 150 nm for the lower layer results in a maximum in MAPD and corresponds to an average fraction of photons absorbed of 34% over the wavelength range 400-1200 nm, resulting in a MAPD of 17.1 mA/cm2.

3.5 Back reflector and antireflection coating

The average absorption probability can be further increased by adding a reflective Ag coating on the backside of the cell to avoid loss of light by transmission. This results in an increase in average absorbance from 33.9% to 40.6%, and an increase in MAPD from 17.1 mA/cm2 to 21 mA/cm2. Figure 7
Fig. 7 Change in spectrum as the backside is coated with silver
shows the resulting change in the absorption spectrum.

A final optimization is the replacement of the 100 nm-thick SiO2 ARC by a 70 nm-thick SiNx ARC, resulting in a MAPD of 21.8mA/cm2 and an average absorption of 43.2%.

3.6 Comparison with solid slab and Yablonovitch limit

Figure 8
Fig. 8 Optical absorbance as a function of wavelength for an equivalent volume cell with flat interfaces (green), a 400 nm-thickness flat cell (cyan) and the optimized structure (blue). The extrapolated geometric light trapping limit (red) is also shown for reference.
shows the fraction of photons absorbed as a function of wavelength for the optimized structure (blue solid line) and for a c-Si slab of equivalent volume which is calculated to have a thickness of 221.6 nm (green solid line). Since the PC structures would likely be fabricated by etching holes into a 400 nm-thick slab of silicon, the performance of the structure is also compared to a 400 nm thick slab (cyan solid line). This calculation is done for normal incidence. The Yablonovitch limit for the same active layer volume is also shown for reference (red dotted line).This limit was calculated by considering multiple reflections of a light ray inside the absorber. The enhanced percentage of photons absorbed Fy is calculated in Eq. (2) as follows
Fy=(1e2al).T1e2al+n22n12.T.e2al.100
(2)
The above equation is a modified version of an equation in [40

40. H. W. Deckman, C. B. Roxlo, and E. Yablonovitch, “Maximum statistical increase of optical absorption in textured semiconductor films,” Opt. Lett. 8(9), 491–493 (1983). [CrossRef] [PubMed]

]. Here 1 is the mean thickness of the sample, a is the optical absorption coefficient, n 1 and n 2 are the refractive indices of the textured medium and the surrounding dielectric, respectively, and T is the Fresnel transmission coefficient which is taken to be 1 assuming a perfect ARC. In the case of a perfect Lambertian surface, the averaged path length of a randomized ray is twice the mean thickness 1 of the film, which accounts for the factor of 2 in the exponent in the above equation. The average absorption of the solid slab of thickness 221.6 nm with a silver back reflector (double pass absorption) is 15.3% while the average absorption of the solid slab of thickness 400 nm is 21.7%. The average absorption for the optimized PC cell with back reflector is 43.2%, The Yablonovitch limit for the c-Si slab of equivalent volume (which has a thickness of 221.6 nm) is 53.2%. The corresponding MAPDs are 21.8 mA/cm2 for the PC cell, 7.1 mA/cm2 for the solid slab with equivalent volume, 10.3 mA/cm2 for the 400 nm-thick solid slab and 26.5 mA/cm2 when the Yablonovitch limit is used for the equivalent volume.

The enhancement in optical absorption of the PC cell over a solid slab of equivalent volume is shown in Fig. 9
Fig. 9 Enhancement in absorbance over a planar structure of 221.6 nm-thickness for the optimized three-layer structure (green) compared to the extrapolated geometric light-trapping limit (red). Also shown, enhancement in absorbance over a planar structure of 400 nm-thickness for the optimized three-layer structure (cyan).
(green solid line). The maximum enhancement in absorption is as high as 169 in narrow peaks and on average, the enhancement is a factor of 8 over the spectral range considered. This enhancement in optical absorption (Fig. 9, green solid line) is compared to the maximum enhancement calculated using the geometric optics limit for a structure with the same volume (Fig. 9, red dotted line). In the case of the geometric optics limit, the average enhancement in optical absorption is 15.9. This is smaller than the optical path length enhancement of 4n2 because the spectral range includes wavelengths where absorption is already strong (<700 nm). The enhancement in optical absorption of the PC cell over a solid slab of the same thickness (400 nm) is also shown in Fig. 9 (cyan solid line). In this case, the maximum enhancement in absorption is a factor of 84.6 and the average enhancement is a factor of 4.4 over the spectral range considered .The enhancement is plotted on a logarithmic scale to emphasize the degree of enhancement in various parts of the spectrum.

3.7 Angular simulations

The enhancements in optical absorption that exceed the Yablonovitch limit shown in Fig. 9 do not violate the limit since it only applies when averaged over all angles of incidence. In Fig. 10a
Fig. 10 (a) Hemispherically averaged absorption is shown as a function of wavelength for s and p incident polarizations. Angular variations in spectrally averaged absorbance in a flat cell are also plotted. (b) Enhancement in absorption for s and p polarizations for a patterned cell over that of an unpatterned cell
, the optical absorption averaged over all incident angles is shown. The hemispherically averaged absorption is plotted as a function of wavelength for both the s (blue solid line) and p (cyan solid line) polarization and compared to the Yablonovitch limit for a 221.6 nm thick solid slab (equivalent total volume). The average absorption for the s and p polarizations is 36.7% and 34.2%, respectively, as compared to 14.5% and 13.9% for a solid slab. The enhancement in optical absorption for the s and p polarizations is shown in Fig. 10b. The average hemispherically integrated enhancement is 2.53 for the s-polarization (blue solid line) and 2.47 for the p-polarization (green solid line).

In Fig. 11, the absorption is plotted as a function of wavelength and polar angle. Here, the absorption is averaged over all azimuthal angles. It is seen that under oblique incidence, new peaks appear and some of the peaks shift. This behavior is consistent with coupling of incident light to quasiguided modes [41

41. S. G. Tikhodeev, A. L. Yablonskii, E. A. Muljarov, N. A. Gippius, and T. Ishihara, “Quasiguided modes and optical properties of photonic crystal slabs,” Phys. Rev. B 66(4), 045102 (2002). [CrossRef]

].

Fig. 11 Absorption averaged over azimuthal angles is shown as a function of wavelength and polar angles for a) s and b) p incident polarizations.

3.8 Analysis of simulated spectra

The location of the absorption peaks in the optimized PC structure can be explained by a simple model that approximates the PC as a waveguide with effective dielectric constants. Each layer of the PC is approximated as a homogeneous layer of volumetric averaged refractive index and the band structure of the corresponding structure is calculated by picking the reflectivity peaks in the complex kxy plane [41]. The band structure of the s-polarized (green) and p-polarized (red) modes supported by the PC waveguide is shown in the lower panel of Fig. 12
Fig. 12 Optical absorption of an optimized PC cell and corresponding dispersion of its quasiguided modes.
. We note that these modes are in reality quasi-guided modes since the PC couples these modes to free space modes. The horizontal black lines correspond to the reciprocal lattice vectors of the periodic lattice of the PC, given by Eq. (3) as follows
k=(2mπp)2+(2nπp)2
(3)
where m and n are integers and p refers to the period. Coupling of normally incident light into quasi-guided modes occurs when the wavevector of a guided mode is equal to a reciprocal lattice vector. The location of most peaks in the absorption spectrum can be attributed to such a match and are predicted within +/ 10 nm, despite the approximations used. The unexplained peaks in the spectrum may be due to the mode dispersion that is not modeled accurately by the simple effective medium model.

A number of quasiguided modes do not show up as peaks in the absorption spectrum when their in-plane wavevector matches a reciprocal lattice vector. This is attributed to weak coupling. The presence of these modes can be detected as shifts in the phase of reflection from the structure for a very weak absorber. For modes that couple very weakly to incident free-space modes, the corresponding resonances are very sharp and hard to detect unless the spectral response is scanned finely.

Figure 13a
Fig. 13 (a)Phase of reflection from structure where absorption is set to zero and corresponding absorption in the wavelength range 488 −497 nm (b) Matched modes (black dots) in band structure for 488-497 nm .(c)Phase of reflection and corresponding absorption in the wavelength range 620-637 nm (b) Matched modes (black dots) in band structure for 620-637 nm. (In Figs. 13(b) and 13(d) green lines correspond to s polarization and red lines to p polarization.)
shows the phase of reflected waves (red line) over the spectral range 488-497 nm. There are two instances of sudden jumps in the otherwise monotonically increasing phase. The first corresponds to a wavelength of 489 nm, indicating that there is a resonance at this wavelength which is not apparent in the corresponding absorption plot (black solid line). From around 492 nm to 495 nm there is an approximately 4π jump in the phase indicating two resonances in close proximity. In Fig. 13b, corresponding detail of the band structure is shown, showing that each match of a quasi-guided mode wavevector to a reciprocal lattice vector is detected as a phase shift in the reflection. No absorption peaks are observed because the coupling is too weak compared to the strong absorption. Figure 13c shows the phase (red dashed line) and absorption (black solid line) over the spectral range 620-637 nm. Sudden jumps in phase are observed at 623 nm, 630 nm and 635 nm. There is an absorption peak at 625 nm which corresponds to a match between a quasi-guided mode wavevector and a reciprocal lattice vector (Fig. 13d). No absorption peaks are observed corresponding to the phase jumps at 630 nm and 635 nm. However, for these wavelengths of 630 nm and 635 nm there is a match between the wavevectors and the reciprocal lattice vectors in Fig. 13d at 631.5 nm and 635 nm respectively indicating weakly coupled modes.

3.9 Electric field distribution

Figures 14a
Fig. 14 Electric field intensity in the vertical cross-section corresponding to a y-coordinate of 150 nm plane at the wavelengths.(a) 918 nm (b) 826 nm
and 14b show the electric field intensity in the xz-plane for 918 nm and 826 nm, respectively. Since both these wavelengths correspond to resonances, most of the intensity is concentrated in the active layer with electric field intensity values exceeding the incident electric field intensity. One concern could be that in Fig. 14a, a lot of the electric field intensity is located at the edges of the structure which could lead to losses due to surface recombination. However, with proper passivation it should be possible to reduce the effects of surface recombination and harvest the carriers generated. Figure 15
Fig. 15 Electric field intensity in the XY plane at the center of (a) the oxide layer at a wavelength of 918 nm and (b) 826 nm, (c) the upper PC layer at a wavelength of 918 nm and (d) 826 nm, and (e) lower PC layer at a wavelength of 918 nm and (f) 826 nm.
shows the electric field intensity in xy-planes located in the center of each of the three patterned layers at the same wavelengths of Fig. 14. Hot spots in the field intensity profile as high as 60 times the incident field intensity are observed.

7. Conclusion

In conclusion, we have designed an effective sub-wavelength light trapping scheme through nano-scale restructuring of the active layer in ultrathin c-Si solar cells. The structure reported consists of a 400 nm-thick c-Si layer patterned into a double-layer PC, supported by a 400 nm-thick SiO2 layer back-coated with Ag. The structure achieves an enhancement of approximately 2.5 in average absorption over a flat cell with equivalent volume of active material when averaged over all angles. Compared to an equivalent volume of active material, the optimized structure gives an enhancement in MAPD of 3.1 for normal incidence. Compared to an equivalent thickness of active material, the optimized structure gives an enhancement in MAPD of 2.1 for normal incidence. Thus, we demonstrate that the enhancement of optical absorption that can be realized using 2D PCs approaches the Yablonovitch limit. When considering a limited range of incident angles, larger enhancements can be obtained which may provide a route for the further optimization of PCs for ultrathin solar cells used in applications where the cells are placed on a solar tracker.

Acknowledgements

This work was supported by the Department of Energy award DE-FG02-07ER46426. We would like to thank Nicholas Sergeant, Zongfu Yu and Shanhui Fan for useful discussions. We would also like to acknowledge computational help provided by Dr. Changsoon Kim.

References and links

1.

K. Yamamoto, T. Suzuki, M. Yoshimi, and A. Nakaijima, “Optical Confinement effect for below 5 µm Thin Film Poly-Si Solar Cell on Glass Substrate,” Jpn. J. Appl. Phys. 36(Part 2, No. 5A), L569–L572 (1997). [CrossRef]

2.

R. Bergmann, T. Rinke, T. Wagner, and J. Werner, “Thin film solar cells on glass based on the transfer of monocrystalline Si films,” Sol. Energy Mater. Sol. Cells 65(1-4), 355–361 (2001). [CrossRef]

3.

H. Tayanaka, K. Yamauchi, and T. Matsushita, “Thin-film crystalline silicon solar cells obtained by separation of a porous silicon sacrificial layer,” in Proceedings of the Second World Conference on Photovoltaic Solar Energy Conversion(1998), p. 1272.

4.

R. M. Swanson, “Point-contact solar cells - Modeling and experiment,” Sol. Cells 17(1), 85–118 (1986). [CrossRef]

5.

M. A. Green, “Limits on the open-circuit voltage and efficiency of Silicon solar cells imposed by intrinsic Auger processes,” IEEE Trans. Electron. Dev. 31(5), 671–678 (1984). [CrossRef]

6.

T. Tiedje, E. Yablonovitch, G. D. Cody, and B. G. Brooks, “Limiting Efficiency of Silicon Solar Cells,” IEEE Trans. Electron. Dev. 31(5), 711–716 (1984). [CrossRef]

7.

L. Danos, G. Jones, R. Greef, and T. Markvart, “Ultra-thin silicon solar cell: Modelling and Characterisation,” Phys. Status Solidi 5(5), 1407–1410 (2008). [CrossRef]

8.

J. Yoon, A. J. Baca, S. I. Park, P. Elvikis, J. B. Geddes 3rd, L. Li, R. H. Kim, J. Xiao, S. Wang, T. H. Kim, M. J. Motala, B. Y. Ahn, E. B. Duoss, J. A. Lewis, R. G. Nuzzo, P. M. Ferreira, Y. Huang, A. Rockett, and J. A. Rogers, “Ultrathin silicon solar microcells for semitransparent, mechanically flexible and microconcentrator module designs,” Nat. Mater. 7(11), 907–915 (2008). [CrossRef] [PubMed]

9.

E. Yablonovitch, “Statistical Ray Optics,” J. Opt. Soc. Am. 72(7), 899–907 (1982). [CrossRef]

10.

E. Yablonovitch and G. D. Cody, “Intensity Enhancement in Textured Optical Sheets for Solar Cells,” IEEE Trans. Electron. Dev. 29(2), 300–305 (1982). [CrossRef]

11.

M. Agrawal, Photonic Design for Efficient Solid-State Energy Conversion, (Stanford University, Stanford, 2008).

12.

J. Gee, “Optically enhanced absorption in thin silicon layers using photonic crystals,” in Twenty-Ninth IEEE Photovolt. Spec. Conf. (2002), pp. 150–153.

13.

S. Pillai, K. Catchpole, T. Trupke, G. Zhang, J. Zhao, and M. A. Green, “Enhanced emission from Si-based light emitting diodes using surface plasmons,” Appl. Phys. Lett. 88(16), 161102 (2006). [CrossRef]

14.

D. M. Schaadt, B. Feng, and E. T. Yu, “Enhanced semiconductor optical absorption via surface plasmon excitation in metal nanoparticles,” Appl. Phys. Lett. 86(6), 063106 (2005). [CrossRef]

15.

P. N. Saeta, V. E. Ferry, D. Pacifici, J. N. Munday, and H. A. Atwater, “How much can guided modes enhance absorption in thin solar cells?” Opt. Express 17(23), 20975–20990 (2009). [CrossRef] [PubMed]

16.

R. H. Morf, and H. Kiess, “Submicron gratings for light trapping in silicon solar cells: a theoretical study,” in Proc. Ninth Internat. Conf. Photvolt. Solar Energy, W. Palz, ed., (Commission of the European Commmunities, Brussels, 1989), pp. 313–315.

17.

M. Gale, B. Curtis, H. Kiess, and R. H. Morf, “Design and fabrication of submicron grating structures for light trapping in silicon solar cells,” Proc. SPIE 1272, 60–66 (1990). [CrossRef]

18.

S. H. Zaidi, J. Gee, and D. S. Ruby, “Diffraction grating structures in solar cells,” in Twenty-Eighth IEEE Photovolt. Spec. Conf. (2000), pp. 395–398.

19.

F. Llopis and I. Tobias, “The role of rear surface in thin silicon solar cells,” Sol. Energy Mater. Sol. Cells 87(1-4), 481–492 (2005). [CrossRef]

20.

Y. Park, E. Drouard, O. El Daif, X. Letartre, P. Viktorovitch, A. Fave, A. Kaminski, M. Lemiti, and C. Seassal, “Absorption enhancement using photonic crystals for silicon thin film solar cells,” Opt. Express 17(16), 14312–14321 (2009). [CrossRef] [PubMed]

21.

D. Zhou and R. Biswas, “Photonic crystal enhanced light-trapping in thin film solar cells,” J. Appl. Phys. 103(9), 093102 (2008). [CrossRef]

22.

P. Bermel, C. Luo, L. Zeng, L. C. Kimerling, and J. D. Joannopoulos, “Improving thin-film crystalline silicon solar cell efficiencies with photonic crystals,” Opt. Express 15(25), 16986–17000 (2007). [CrossRef] [PubMed]

23.

L. Zeng, Y. Yi, C. Hong, J. Liu, N. Feng, X. Duan, L. C. Kimerling, and B. A. Alamariu, “Efficiency enhancement in Si solar cells by textured photonic crystal back reflector,” Appl. Phys. Lett. 89(11), 111111 (2006). [CrossRef]

24.

J. G. Mutitu, S. Shi, C. Chen, T. Creazzo, A. Barnett, C. Honsberg, and D. W. Prather, “Thin film solar cell design based on photonic crystal and diffractive grating structures,” Opt. Express 16(19), 15238–15248 (2008). [CrossRef] [PubMed]

25.

C. L. Huisman, J. Schoonman, and A. Goossens, “The application of inverse titania opals in nanostructured solar cells,” Sol. Energy Mater. Sol. Cells 85, 115–124 (2005).

26.

A. Mihi and H. Míguez, “Origin of light-harvesting enhancement in colloidal-photonic-crystal-based dye-sensitized solar cells,” J. Phys. Chem. B 109(33), 15968–15976 (2005). [CrossRef]

27.

S. Nishimura, N. Abrams, B. A. Lewis, L. I. Halaoui, T. E. Mallouk, K. D. Benkstein, J. van de Lagemaat, and A. J. Frank, “Standing wave enhancement of red absorbance and photocurrent in dye-sensitized titanium dioxide photoelectrodes coupled to photonic crystals,” J. Am. Chem. Soc. 125(20), 6306–6310 (2003). [CrossRef] [PubMed]

28.

N. N. Feng, J. Michel, L. Zeng, J. Liu, C. Y. Hong, L. C. Kimerling, and X. Duan, “Design of Highly Efficient Light-Trapping Structures for Thin-Film Crystalline Silicon Solar Cells,” IEEE Trans. Electron. Dev. 54(8), 1926–1933 (2007). [CrossRef]

29.

P. G. O'Brien, N. P. Kherani, A. Chutinan, G. A. Ozin, S. John, and S. Zukotynski, “Silicon photovoltaics using conducting photonic crystal back-reflectors,” Adv. Mater. 20(8), 1577–1582 (2008). [CrossRef]

30.

P. G. O'Brien, N. P. Kherani, S. Zukotynski, G. A. Ozin, E. Vekris, N. Tetreault, A. Chutinan, S. John, A. Mihi, and H. Miguez, “Enhanced photoconductivity in thin-film semiconductors optically coupled to photonic crystals,” Adv. Mater. 19(23), 4177–4182 (2007). [CrossRef]

31.

A. Chutinan, N. P. Kherani, and S. Zukotynski, “High-efficiency photonic crystal solar cell architecture,” Opt. Express 17(11), 8871–8878 (2009). [CrossRef] [PubMed]

32.

M. G. Moharam, D. A. Pommet, E. B. Grann, and T. K. Gaylord, “Stable implementation of the rigorous coupled-wave analysis for surface-relief gratings:enhanced transmittance matrix approach,” J. Opt. Soc. Am. A 12(5), 1077–1086 (1995). [CrossRef]

33.

M. G. Moharam, E. B. Grann, D. A. Pommet, and T. K. Gaylord, “Formulation for stable and efficient implementation of the rigorous coupled-wave analysis of binary gratings,” J. Opt. Soc. Am. A 12(5), 1068–1076 (1995). [CrossRef]

34.

L. Li, “New formulation of the Fourier modal method for crossed surface-relief gratings,” J. Opt. Soc. Am. A 14(10), 2758–2767 (1997). [CrossRef]

35.

P. Lalanne and E. Silberstein, “Fourier-modal methods applied to waveguide computational problems,” Opt. Lett. 25(15), 1092–1094 (2000). [CrossRef]

36.

J. H. Jiang, P. C. Deguzman, and G. P. Nordin, “Analysis of stacked rotated gratings,” Appl. Opt. 46(8), 1177–1183 (2007). [CrossRef] [PubMed]

37.

S. Peng and M. Morris, “Efficient implementation of rigorous coupled-wave analysis for surface-relief gratings,” J. Opt. Soc. Am. A 12(5), 1087–1096 (1995). [CrossRef]

38.

D. M. Chambers and G. P. Nordin, “Stratified volume diffractive optical elements as high-efficiency gratings,” J. Opt. Soc. Am. A 16(5), 1184–1193 (1999). [CrossRef]

39.

A. G. Aberle, “Surface passivation of crystalline silicon solar cells: a review,” Prog. Photovoltaics 8(5), 473–487 (2000). [CrossRef]

40.

H. W. Deckman, C. B. Roxlo, and E. Yablonovitch, “Maximum statistical increase of optical absorption in textured semiconductor films,” Opt. Lett. 8(9), 491–493 (1983). [CrossRef] [PubMed]

41.

S. G. Tikhodeev, A. L. Yablonskii, E. A. Muljarov, N. A. Gippius, and T. Ishihara, “Quasiguided modes and optical properties of photonic crystal slabs,” Phys. Rev. B 66(4), 045102 (2002). [CrossRef]

OCIS Codes
(350.6050) Other areas of optics : Solar energy
(350.4238) Other areas of optics : Nanophotonics and photonic crystals

ToC Category:
Solar Energy

History
Original Manuscript: December 3, 2009
Revised Manuscript: January 16, 2010
Manuscript Accepted: February 22, 2010
Published: March 5, 2010

Virtual Issues
Focus Issue: Solar Concentrators (2010) Optics Express

Citation
Shrestha Basu Mallick, Mukul Agrawal, and Peter Peumans, "Optimal light trapping in ultra-thin photonic crystal crystalline silicon solar cells," Opt. Express 18, 5691-5706 (2010)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-18-6-5691


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. K. Yamamoto, T. Suzuki, M. Yoshimi, and A. Nakaijima, “Optical Confinement effect for below 5 µm Thin Film Poly-Si Solar Cell on Glass Substrate,” Jpn. J. Appl. Phys. 36(Part 2, No. 5A), L569–L572 (1997). [CrossRef]
  2. R. Bergmann, T. Rinke, T. Wagner, and J. Werner, “Thin film solar cells on glass based on the transfer of monocrystalline Si films,” Sol. Energy Mater. Sol. Cells 65(1-4), 355–361 (2001). [CrossRef]
  3. H. Tayanaka, K. Yamauchi, and T. Matsushita, “Thin-film crystalline silicon solar cells obtained by separation of a porous silicon sacrificial layer,” in Proceedings of the Second World Conference on Photovoltaic Solar Energy Conversion(1998), p. 1272.
  4. R. M. Swanson, “Point-contact solar cells - Modeling and experiment,” Sol. Cells 17(1), 85–118 (1986). [CrossRef]
  5. M. A. Green, “Limits on the open-circuit voltage and efficiency of Silicon solar cells imposed by intrinsic Auger processes,” IEEE Trans. Electron. Dev. 31(5), 671–678 (1984). [CrossRef]
  6. T. Tiedje, E. Yablonovitch, G. D. Cody, and B. G. Brooks, “Limiting Efficiency of Silicon Solar Cells,” IEEE Trans. Electron. Dev. 31(5), 711–716 (1984). [CrossRef]
  7. L. Danos, G. Jones, R. Greef, and T. Markvart, “Ultra-thin silicon solar cell: Modelling and Characterisation,” Phys. Status Solidi 5(5), 1407–1410 (2008). [CrossRef]
  8. J. Yoon, A. J. Baca, S. I. Park, P. Elvikis, J. B. Geddes, L. Li, R. H. Kim, J. Xiao, S. Wang, T. H. Kim, M. J. Motala, B. Y. Ahn, E. B. Duoss, J. A. Lewis, R. G. Nuzzo, P. M. Ferreira, Y. Huang, A. Rockett, and J. A. Rogers, “Ultrathin silicon solar microcells for semitransparent, mechanically flexible and microconcentrator module designs,” Nat. Mater. 7(11), 907–915 (2008). [CrossRef] [PubMed]
  9. E. Yablonovitch, “Statistical Ray Optics,” J. Opt. Soc. Am. 72(7), 899–907 (1982). [CrossRef]
  10. E. Yablonovitch and G. D. Cody, “Intensity Enhancement in Textured Optical Sheets for Solar Cells,” IEEE Trans. Electron. Dev. 29(2), 300–305 (1982). [CrossRef]
  11. M. Agrawal, Photonic Design for Efficient Solid-State Energy Conversion, (Stanford University, Stanford, 2008).
  12. J. Gee, “Optically enhanced absorption in thin silicon layers using photonic crystals,” in Twenty-Ninth IEEE Photovolt. Spec. Conf. (2002), pp. 150–153.
  13. S. Pillai, K. Catchpole, T. Trupke, G. Zhang, J. Zhao, and M. A. Green, “Enhanced emission from Si-based light emitting diodes using surface plasmons,” Appl. Phys. Lett. 88(16), 161102 (2006). [CrossRef]
  14. D. M. Schaadt, B. Feng, and E. T. Yu, “Enhanced semiconductor optical absorption via surface plasmon excitation in metal nanoparticles,” Appl. Phys. Lett. 86(6), 063106 (2005). [CrossRef]
  15. P. N. Saeta, V. E. Ferry, D. Pacifici, J. N. Munday, and H. A. Atwater, “How much can guided modes enhance absorption in thin solar cells?” Opt. Express 17(23), 20975–20990 (2009). [CrossRef] [PubMed]
  16. R. H. Morf, and H. Kiess, “Submicron gratings for light trapping in silicon solar cells: a theoretical study,” in Proc. Ninth Internat. Conf. Photvolt. Solar Energy, W. Palz, ed., (Commission of the European Commmunities, Brussels, 1989), pp. 313–315.
  17. M. Gale, B. Curtis, H. Kiess, and R. H. Morf, “Design and fabrication of submicron grating structures for light trapping in silicon solar cells,” Proc. SPIE 1272, 60–66 (1990). [CrossRef]
  18. S. H. Zaidi, J. Gee, and D. S. Ruby, “Diffraction grating structures in solar cells,” in Twenty-Eighth IEEE Photovolt. Spec. Conf. (2000), pp. 395–398.
  19. F. Llopis and I. Tobias, “The role of rear surface in thin silicon solar cells,” Sol. Energy Mater. Sol. Cells 87(1-4), 481–492 (2005). [CrossRef]
  20. Y. Park, E. Drouard, O. El Daif, X. Letartre, P. Viktorovitch, A. Fave, A. Kaminski, M. Lemiti, and C. Seassal, “Absorption enhancement using photonic crystals for silicon thin film solar cells,” Opt. Express 17(16), 14312–14321 (2009). [CrossRef] [PubMed]
  21. D. Zhou and R. Biswas, “Photonic crystal enhanced light-trapping in thin film solar cells,” J. Appl. Phys. 103(9), 093102 (2008). [CrossRef]
  22. P. Bermel, C. Luo, L. Zeng, L. C. Kimerling, and J. D. Joannopoulos, “Improving thin-film crystalline silicon solar cell efficiencies with photonic crystals,” Opt. Express 15(25), 16986–17000 (2007). [CrossRef] [PubMed]
  23. L. Zeng, Y. Yi, C. Hong, J. Liu, N. Feng, X. Duan, L. C. Kimerling, and B. A. Alamariu, “Efficiency enhancement in Si solar cells by textured photonic crystal back reflector,” Appl. Phys. Lett. 89(11), 111111 (2006). [CrossRef]
  24. J. G. Mutitu, S. Shi, C. Chen, T. Creazzo, A. Barnett, C. Honsberg, and D. W. Prather, “Thin film solar cell design based on photonic crystal and diffractive grating structures,” Opt. Express 16(19), 15238–15248 (2008). [CrossRef] [PubMed]
  25. C. L. Huisman, J. Schoonman, and A. Goossens, “The application of inverse titania opals in nanostructured solar cells,” Sol. Energy Mater. Sol. Cells 85, 115–124 (2005).
  26. A. Mihi and H. Míguez, “Origin of light-harvesting enhancement in colloidal-photonic-crystal-based dye-sensitized solar cells,” J. Phys. Chem. B 109(33), 15968–15976 (2005). [CrossRef]
  27. S. Nishimura, N. Abrams, B. A. Lewis, L. I. Halaoui, T. E. Mallouk, K. D. Benkstein, J. van de Lagemaat, and A. J. Frank, “Standing wave enhancement of red absorbance and photocurrent in dye-sensitized titanium dioxide photoelectrodes coupled to photonic crystals,” J. Am. Chem. Soc. 125(20), 6306–6310 (2003). [CrossRef] [PubMed]
  28. N. N. Feng, J. Michel, L. Zeng, J. Liu, C. Y. Hong, L. C. Kimerling, and X. Duan, “Design of Highly Efficient Light-Trapping Structures for Thin-Film Crystalline Silicon Solar Cells,” IEEE Trans. Electron. Dev. 54(8), 1926–1933 (2007). [CrossRef]
  29. P. G. O'Brien, N. P. Kherani, A. Chutinan, G. A. Ozin, S. John, and S. Zukotynski, “Silicon photovoltaics using conducting photonic crystal back-reflectors,” Adv. Mater. 20(8), 1577–1582 (2008). [CrossRef]
  30. P. G. O'Brien, N. P. Kherani, S. Zukotynski, G. A. Ozin, E. Vekris, N. Tetreault, A. Chutinan, S. John, A. Mihi, and H. Miguez, “Enhanced photoconductivity in thin-film semiconductors optically coupled to photonic crystals,” Adv. Mater. 19(23), 4177–4182 (2007). [CrossRef]
  31. A. Chutinan, N. P. Kherani, and S. Zukotynski, “High-efficiency photonic crystal solar cell architecture,” Opt. Express 17(11), 8871–8878 (2009). [CrossRef] [PubMed]
  32. M. G. Moharam, D. A. Pommet, E. B. Grann, and T. K. Gaylord, “Stable implementation of the rigorous coupled-wave analysis for surface-relief gratings:enhanced transmittance matrix approach,” J. Opt. Soc. Am. A 12(5), 1077–1086 (1995). [CrossRef]
  33. M. G. Moharam, E. B. Grann, D. A. Pommet, and T. K. Gaylord, “Formulation for stable and efficient implementation of the rigorous coupled-wave analysis of binary gratings,” J. Opt. Soc. Am. A 12(5), 1068–1076 (1995). [CrossRef]
  34. L. Li, “New formulation of the Fourier modal method for crossed surface-relief gratings,” J. Opt. Soc. Am. A 14(10), 2758–2767 (1997). [CrossRef]
  35. P. Lalanne and E. Silberstein, “Fourier-modal methods applied to waveguide computational problems,” Opt. Lett. 25(15), 1092–1094 (2000). [CrossRef]
  36. J. H. Jiang, P. C. Deguzman, and G. P. Nordin, “Analysis of stacked rotated gratings,” Appl. Opt. 46(8), 1177–1183 (2007). [CrossRef] [PubMed]
  37. S. Peng and M. Morris, “Efficient implementation of rigorous coupled-wave analysis for surface-relief gratings,” J. Opt. Soc. Am. A 12(5), 1087–1096 (1995). [CrossRef]
  38. D. M. Chambers and G. P. Nordin, “Stratified volume diffractive optical elements as high-efficiency gratings,” J. Opt. Soc. Am. A 16(5), 1184–1193 (1999). [CrossRef]
  39. A. G. Aberle, “Surface passivation of crystalline silicon solar cells: a review,” Prog. Photovoltaics 8(5), 473–487 (2000). [CrossRef]
  40. H. W. Deckman, C. B. Roxlo, and E. Yablonovitch, “Maximum statistical increase of optical absorption in textured semiconductor films,” Opt. Lett. 8(9), 491–493 (1983). [CrossRef] [PubMed]
  41. S. G. Tikhodeev, A. L. Yablonskii, E. A. Muljarov, N. A. Gippius, and T. Ishihara, “Quasiguided modes and optical properties of photonic crystal slabs,” Phys. Rev. B 66(4), 045102 (2002). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited