Measurement range enlargement in Brillouin optical correlation-domain reflectometry based on double-modulation scheme

doi:10.1364/OE.18.005926

« Show journal navigation

Measurement range enlargement in Brillouin optical correlation-domain reflectometry based on double-modulation scheme

Yosuke Mizuno, Zuyuan He, and Kazuo Hotate »View Author Affiliations

Optics Express, Vol. 18, Issue 6, pp. 5926-5933 (2010)
http://dx.doi.org/10.1364/OE.18.005926

View Full Text Article

Acrobat PDF (423 KB)

Journal Search
Article Lookup

Article Tools

Citations

Alert me when this article is cited
Export Citation/Save

Article Navigation

▸ Article Outline
– Abstract
1. Introduction
2. Principle
3. Theoretical analysis and simulation
4. Experiments
5. Conclusion
– References and links

Article Tools
Full Text
Article Info
References
Cited By
Figures
Metrics
Download PDF

Viewing Equations in the
HTML Article

Optimal Viewing Recommendations

Full Text
Article Info
References (18)
Cited By
Figures (7)
Metrics

Abstract

We have demonstrated a double-modulation scheme to enlarge the measurement range of Brillouin optical correlation-domain reflectometry for fiber-optic distributed strain sensing. In this scheme, the frequency of the laser output is simultaneously modulated with two different frequencies. In the experiment, 53-cm resolution and 1.5-km measurement range were simultaneously obtained. Furthermore, 27-cm resolution and 1.5-km measurement range were also simultaneously achieved when a noise-floor compensation technique was employed.

1. Introduction

Among various kinds of fiber-optic sensors, Brillouin optical correlation-domain reflectometry (BOCDR) [1

Y. Mizuno, W. Zou, Z. He, and K. Hotate, “Proposal of Brillouin optical correlation-domain reflectometry (BOCDR),” Opt. Express 16(16), 12148–12153 (2008). [CrossRef] [PubMed]

] has the capacity to measure the distribution of strain and/or temperature along a fiber under test (FUT) from a single end. So far, 13-mm spatial resolution has been obtained in a silica fiber [2

Y. Mizuno, Z. He, and K. Hotate, “One-end-access high-speed distributed strain measurement with 13-mm spatial resolution based on Brillouin optical correlation-domain reflectometry,” IEEE Photon. Technol. Lett. 21(7), 474–476 (2009). [CrossRef]

], which is the best result ever reported in spontaneous Brillouin scattering-based reflectometers. However, BOCDR suffers from a trade-off between the measurement range and the spatial resolution. Their ratio N_R is fixed at approximately 570 due to the limitation caused by Rayleigh scattering-induced noise [1

Y. Mizuno, W. Zou, Z. He, and K. Hotate, “Proposal of Brillouin optical correlation-domain reflectometry (BOCDR),” Opt. Express 16(16), 12148–12153 (2008). [CrossRef] [PubMed]

]. For example, when the spatial resolution is set to 40 cm or 13 mm, the measurement range becomes 224 m [1

Y. Mizuno, W. Zou, Z. He, and K. Hotate, “Proposal of Brillouin optical correlation-domain reflectometry (BOCDR),” Opt. Express 16(16), 12148–12153 (2008). [CrossRef] [PubMed]

] or 7.6 m [2

], respectively. Thus, in order to achieve kilometer-order measurement range, the resolution must be 2 m or larger, which is even worse than that of basic time-domain techniques (~1 m [3

A. Fellay, L. Thevenaz, M. Facchini, M. Nikles, and P. Robert, “Distributed sensing using stimulated Brillouin scattering: towards ultimate resolution,” Proc. 12th Intern. Conf. Optical Fiber Sensors, 324–327 (1997).

]), such as Brillouin optical time-domain reflectometry (BOTDR) [4

T. Kurashima, T. Horiguchi, H. Izumita, S. Furukawa, and Y. Koyamada, “Brillouin optical-fiber time domain reflectometry,” IEICE Trans. Commun,” E 76-B, 382–390 (1993).

] and Brillouin optical time-domain analysis (BOTDA) [5

T. Horiguchi and M. Tateda, “BOTDA-nondestructive measurement of single-mode optical fiber attenuation characteristics using Brillouin interaction: theory,” J. Lightwave Technol. 7(8), 1170–1176 (1989). [CrossRef]

]. In the time-domain systems, some progress has also been made to enhance the resolution [6

Y. Koyamada, Y. Sakairi, N. Takeuchi, and S. Adachi, “Novel technique to improve spatial resolution in Brillouin optical time-domain reflectometry,” IEEE Photon. Technol. Lett. 19(23), 1910–1912 (2007). [CrossRef]

]-[7

W. Li, X. Bao, Y. Li, and L. Chen, “Differential pulse-width pair BOTDA for high spatial resolution sensing,” Opt. Express 16(26), 21616–21625 (2008). [CrossRef] [PubMed]

To obtain higher N_R, a temporal gating scheme was implemented [8

Y. Mizuno, Z. He, and K. Hotate, “Measurement range enlargement in Brillouin optical correlation-domain reflectometry based on temporal gating scheme,” Opt. Express 17(11), 9040–9046 (2009). [CrossRef] [PubMed]

], where any correlation peak within the FUT can be arbitrarily selected by a time-domain technique. In the experiment, 66-cm resolution and 1-km measurement range were simultaneously achieved. The ratio N_R was 1515, which is about three times as high as that of the basic BOCDR. However, the signal-to-noise (S/N) ratio was so low that N_R could not be enhanced further.

In the case of Brillouin optical correlation-domain analysis (BOCDA) systems [9

K. Hotate and T. Hasegawa, “Measurement of Brillouin gain spectrum distribution along an optical fiber using a correlation-based technique – proposal, experiment and simulation,” IEICE Trans. Electron E 83-C, 405–412 (2000).

], a multiple-modulation scheme is known to be an alternative method to obtain higher N_R [10

K. Hotate and M. Tanaka, “Correlation-based continuous-wave technique for optical fiber distributed strain measurement using Brillouin scattering with cm-order spatial resolution – applications to smart materials,” IEICE Trans. Electron E 84-C, 1823–1828 (2001).

], where the frequency of the laser output is simultaneously modulated with multiple different frequencies. In the previous experiment, by modulating the laser output at 2f₀ and 3f₀ simultaneously (where f₀ is a fundamental frequency), N_R was enhanced by three times.

In this paper, we demonstrate a double-modulation scheme to enlarge the measurement range of BOCDR while maintaining the spatial resolution. The optimized modulation parameters are described, such as the combination of the frequencies to be used, and their amplitudes. Then, the operating principle of the scheme is theoretically analyzed and simulated. In the experiment, a strain-applied 90-cm section is successfully detected with 53.1-cm resolution and 1.51-km measurement range (N_R = 2845). Moreover, a strain-applied 40-cm section is also detected with 26.5-cm resolution and 1.51-km measurement range (N_R = 5690) by the use of a noise-floor compensation technique.

2. Principle

Spontaneous Brillouin scattering occurs when light is Bragg-reflected by the refractive index modulations produced by acoustic phonons. Since the phonons decay exponentially, the backscattered Brillouin light (Stokes light) spectrum, also known as Brillouin gain spectrum (BGS), takes the shape of a Lorentzian function [11

G. P. Agrawal, Nonlinear Fiber Optics (Academic Press, California, 1995).

]. The Stokes light suffers a Doppler shift called Brillouin frequency shift (BFS), which depends on tensile strain and temperature change applied to the optical fiber. For example, in a standard silica single-mode fiber (SMF), BFS of about 11 GHz slightly varies to higher frequency in proportion to the applied strain and the temperature change with coefficients of 0.058 MHz/με [12

T. Horiguchi, T. Kurashima, and M. Tateda, “Tensile strain dependence of Brillouin frequency shift in silica optical fibers,” IEEE Photon. Technol. Lett. 1(5), 107–108 (1989). [CrossRef]

] and 1.18 MHz/K [13

T. Kurashima, T. Horiguchi, and M. Tateda, “Thermal effects on the Brillouin frequency shift in jacketed optical silica fibers,” Appl. Opt. 29(15), 2219–2222 (1990). [CrossRef] [PubMed]

], respectively. Hence, BFS can provide the information on the magnitude of strain and temperature change in the fiber.

BOCDR [1

Y. Mizuno, W. Zou, Z. He, and K. Hotate, “Proposal of Brillouin optical correlation-domain reflectometry (BOCDR),” Opt. Express 16(16), 12148–12153 (2008). [CrossRef] [PubMed]

] is a technology to measure the distribution of strain and/or temperature along an FUT from a single end, based on the correlation control of continuous lightwaves. The Stokes light due to the spontaneous Brillouin scattering of the pump light in the FUT is heterodyned with the reference light (self heterodyne). In order to resolve the strain-applied position, the pump light and the reference light are sinusoidally frequency-modulated, producing periodical correlation peaks along the FUT. The measurement range d_m, that is, the interval of the correlation peaks, and the spatial resolution Δ z are given by:

d_{m} = \frac{c}{2 n f_{\mod}},

(1)

Δ z = \frac{c Δ ν_{B}}{2 π n f_{\mod} Δ f},

(2)

respectively, where c is the velocity of light, n the refractive index, f_mod the modulation frequency of the light source, Δν_Β the Brillouin gain bandwidth in optical fibers, and Δ f the modulation amplitude of the light source. The number of effective sensing points N_R, which can be regarded as the evaluation parameter of the system, is given by the ratio between d_m and Δ z, as:

N_{R} = \frac{d_{m}}{Δ z} = \frac{π Δ f}{Δ ν_{B}} .

(3)

According to Eq. (3), Δf needs to be increased to obtain higher N_R. Although Δf is not limited in BOCDA [14

K. Y. Song, Z. He, and K. Hotate, “Distributed strain measurement with millimeter-order spatial resolution based on Brillouin optical correlation domain analysis,” Opt. Lett. 31(17), 2526–2528 (2006). [CrossRef] [PubMed]

], Δf must be lower than a half of BFS in the fiber in BOCDR [1

Y. Mizuno, W. Zou, Z. He, and K. Hotate, “Proposal of Brillouin optical correlation-domain reflectometry (BOCDR),” Opt. Express 16(16), 12148–12153 (2008). [CrossRef] [PubMed]

], which results in N_R lower than about 570 for standard silica fibers.

Another way to achieve higher N_R is to utilize multiple intervals of the correlation peaks. In this case, we select only one correlation peak for a distributed measurement, but suppress other peaks to avoid the crosstalk. Therefore, the measurement range is multiplied while the spatial resolution is maintained. Along with the temporal gating scheme [8

], the double-modulation scheme is an effective method for this purpose, and was applied to BOCDA [10

The experimental setup of BOCDR based on the double-modulation scheme is depicted in Fig. 1 . The roles of each device including the polarization scrambler (PSCR) and the optical filters are the same as described in [15

Y. Mizuno, Z. He, and K. Hotate, “Stable entire-length measurement of fiber strain distribution by Brillouin optical correlation-domain reflectometry with polarization scrambling and noise-floor compensation,” Appl. Phys. Express 2, 062403 (2009). [CrossRef]

]. The pump light and the reference light are sinusoidally frequency-modulated with two different frequencies, f₀ ( + f_ε) and m f₀, where f₀ is a fundamental frequency, m is an integer, and f_ε (~0.5 kHz) is needed to avoid beating between the two frequencies, which causes large fluctuations of BGS. The amplitude of the frequency modulation at f₀, denoted as Δf₁, is set to be several hundreds of MHz (difficult to measure accurately due to the frequency characteristics of the laser circuit). The amplitude at m f₀, denoted as Δf_m, is about 5.4 GHz (a little lower than a half of BFS in silica fibers). Then, as shown in Fig. 2 , the spatial resolution is determined by m f₀, while the correlation peaks of which the orders are not multiples of m are suppressed by f₀. Since the modulation at f₀ does not influence on the resolution due to the low Δf₁, it becomes possible to achieve the spatial resolution determined by m f₀ and the measurement range determined by f₀ simultaneously, leading to a larger N_R by m times.

Fig. 1 Experimental setup of BOCDR based on double-modulation scheme: DAQ, data acquisition; DC, direct current; EDFA, erbium-doped fiber amplifier; ESA, electrical spectrum analyzer; FUT, fiber under test; GPIB, general-purpose interface bus; PC, polarization controller; PD, photo-detector; PSCR, polarization scrambler.

Fig. 2 Operating principle of double-modulation scheme.

3. Theoretical analysis and simulation

The operating principle of the double-modulation scheme was theoretically analyzed. The frequency modulation of the laser output is represented as Eq. (4):

f (t) = f_{c} + Δ f_{m} \sin (2 π m f_{0} t) + Δ f_{1} \sin (2 π f_{0} t),

(4)

where is the center frequency. Then, the electric field of the laser output is expressed as Eq. (5):

E (t) = \exp {- j Φ (t)},

(5)

where Φ(t) is defined by Eq. (6):

Φ (t) = \int_{0}^{t} 2 π f (t^{'}) d t^{'} .

(6)

It is known that the optical coherence function, which is the shape of the correlation peaks along the FUT, is given by the Fourier transform of the spectral density of the light source, or in other words, the autocorrelation function of the electric field of the light source [16

Y. Ohtsuka, “Optical coherence effects on a fiber-sensing Fabry-Perot interferometer,” Appl. Opt. 21(23), 4316–4320 (1982). [CrossRef] [PubMed]

]. Therefore, the absolute value of the optical coherence function is calculated as

| γ (τ_{d}) | = | \lim_{T \to \infty} \frac{1}{T} \int_{- \frac{T}{2}}^{\frac{T}{2}} \exp {- j Φ (t)} \exp {j Φ (t - τ_{d})} d t |

= | \lim_{T \to \infty} \frac{1}{T} \int_{- \frac{T}{2}}^{\frac{T}{2}} \exp [j {- 2 π f_{c} τ_{d} + 2 \frac{Δ f_{m}}{m f_{0}} \sin (π m f_{0} τ_{d}) \sin (2 π m f_{0} (t - \frac{τ_{d}}{2}))

+ 2 \frac{Δ f_{1}}{f_{0}} \sin (π f_{0} τ_{d}) \sin (2 π f_{0} (t - \frac{τ_{d}}{2}))}] d t |

\begin{array}{l} = | \lim_{T \to \infty} \frac{1}{T} \int_{- \frac{T}{2}}^{\frac{T}{2}} \sum_{p = - \infty}^{\infty} J_{p} (2 \frac{Δ f_{m}}{m f_{0}} \sin (π m f_{0} τ_{d})) \exp {j 2 π p m f_{0} (t - \frac{τ_{d}}{2})} \\ \cdot \sum_{q = - \infty}^{\infty} J_{q} (2 \frac{Δ f_{1}}{f_{0}} \sin (π f_{0} τ_{d})) \exp {j 2 π q f_{0} (t - \frac{τ_{d}}{2})} d t | \end{array}

\begin{array}{l} = | \lim_{T \to \infty} \frac{1}{T} \int_{- \frac{T}{2}}^{\frac{T}{2}} \sum_{p = - \infty}^{\infty} \sum_{q = - \infty}^{\infty} J_{p} (2 \frac{Δ f_{m}}{m f_{0}} \sin (π m f_{0} τ_{d})) \cdot J_{q} (2 \frac{Δ f_{1}}{f_{0}} \sin (π f_{0} τ_{d})) \\ \cdot \exp {j 2 π (p m + q) f_{0} (t - \frac{τ_{d}}{2})} d t | \end{array}

= | \sum_{p = - \infty}^{\infty} J_{p} (2 \frac{Δ f_{m}}{m f_{0}} \sin (π m f_{0} τ_{d})) \cdot J_{- p m} (2 \frac{Δ f_{1}}{f_{0}} \sin (π f_{0} τ_{d})) |,

(7)

where τ_d is the time delay and J_p(x) is the p-th Bessel function of the first kind. When m >> 1, Eq. (7) is approximately equal to Eq. (8):

| γ (τ_{d}) | \approx | J_{0} (2 \frac{Δ f_{m}}{m f_{0}} \sin (π m f_{0} τ_{d})) | \cdot | J_{0} (2 \frac{Δ f_{1}}{f_{0}} \sin (π f_{0} τ_{d})) |,

(8)

which shows that the synthesized coherence function in the double-modulation scheme is roughly given by the product of the coherence functions synthesized into a series of periodical delta-function-like peaks by each modulation frequency.

Based on Eq. (7), we simulated the synthesized coherence function when m = 4, as shown in Figs. 3(a) -3(c). The ratio of the modulation amplitudes (Δf₄ / Δf₁) was set to 10. In Fig. 3(c), the 1st, 2nd, 3rd, 5th, 6th, 7th, and 9th correlation peaks were suppressed, which shows that the measurement range was multiplied by 4 times while maintaining the spatial resolution.

Fig. 3 Synthesized coherence functions with the modulation at (a) f₀ only, (b) 4f₀ only, and (c) f₀ and 4f₀ .

4. Experiments

First, the effectiveness of the double-modulation scheme was experimentally shown. As the two modulation frequencies, f₀ and 5f₀ were used (Δf₅ = 5.4 GHz), where f₀ was set to 68.481 kHz. According to Eqs. (1) and (2), the spatial resolution and the measurement range determined by the conventional single modulation at 5f₀ were 53.1 cm and 302.1 m, respectively. An SMF of 1 km was used as the FUT, and about 0.15-% strain was applied to a 3-m section (990 – 993 m). The correlation peak was placed at the middle of the strain-applied section. The polarization state was optimized by adjusting polarization controllers so that the peak intensity of BGS without strain applied becomes maximal. Averaging was conducted 10 times to measure one BGS.

Figure 4(a) shows the measured BGS with and without strain applied when the single modulation at 5f₀ was applied. Since there were three correlation peaks within the FUT, the change of BGS was not observed as a clear shift of the peak. Here, a kink observed at 10.9 GHz was caused by range switching of the electrical spectrum analyzer (ESA). In contrast, Fig. 4(b) shows the measured BGS when the double-modulation scheme was employed. The applied strain was observed as a clear shift of the BGS peak. The remaining peak at about 10.86 GHz in the curve with strain applied, which can be regarded as noise, originates from the correlation sidelobes that were not completely suppressed. As long as this remaining peak is lower in power than the BGS peak, the measurement is performed correctly. In practical cases with two or more strains applied along the FUT, the power of the remaining peak becomes even smaller.

Fig. 4 Measured strain-dependences of BGS (a) without and (b) with double-modulation scheme.

Then, the double modulation and the single modulation were compared in a distributed strain measurement. A strain of 0.15% was applied to a 90-cm section (990.0 – 990.9 m). With f₀ swept from 68.362 kHz to 68.497 kHz, BGS was measured every 5 cm. The other conditions were the same as those in the preceding experiment. The measured distributions of BGS and BFS with the single modulation at 5f₀ (m = 5) are shown in Figs. 5(a) and 5(b), respectively. Although BGS slightly changed at the strain-applied section, a correct distribution of BFS was not acquired. On the other hand, the measured results in the double-modulation scheme with f₀ and 5f₀ are shown in Figs. 6(a) and 6(b). The strain-applied 90-cm section was correctly detected. The measurement accuracy in this experiment was about +/– 7 MHz, corresponding to about +/– 120 με. The ratio N_R was 2845 ( = 1.51 km / 53.1 cm), which is much higher than 1515 obtained previously in the temporal gating scheme.

Fig. 5 Measured distributions of (a) BGS, and (b) BFS when the double-modulation scheme was not employed.

Fig. 6 Measured distributions of (a) BGS, and (b) BFS when the double-modulation scheme was employed (N_R = 2845).

The upper limit of m is determined by noise floor of the ESA, polarization state, FUT length, nonlinear dependence of LD frequency, etc. As m is increased, the S/N ratio is deteriorated due to the following two reasons: (i) the remaining peak (noise) in Fig. 4(b) becomes larger; (ii) the spatial resolution becomes higher, which accompanies the reduction of the BGS signal power. The second reason also deteriorates the measurement accuracy.

Finally, the double-modulation scheme was implemented with f₀ and 10f₀ (Δf₁₀ = 5.4 GHz) using a noise-floor compensation technique [15

]. A strain of 0.15% was applied to a 40-cm section (990.0 – 990.4 m). With f₀ swept from 68.362 kHz to 68.474 kHz, the spatial resolution and the measurement range were 26.5 cm and 1.51 km, respectively, corresponding to N_R of 5690. The measured results are shown in Figs. 7(a) and 7(b). Although the S/N ratio was deteriorated compared to that in Fig. 6, the strain-applied 40-cm section was successfully detected. The measurement accuracy was about +/– 15 MHz, corresponding to about +/– 260 με. We think further research is needed to enhance the measurement accuracy by employing some methods such as those described in Refs [17

A. W. Brown, M. D. DeMerchant, X. Bao, and T. W. Bremner, “Spatial resolution enhancement of a Brillouin-distributed sensor using a novel signal processing method,” J. Lightwave Technol. 17(7), 1179–1183 (1999). [CrossRef]

]-[18

M. P. Song and B. Zhao, “Accuracy enhancement in Brillouin scattering distributed temperature sensor based on Hilbert transform,” Opt. Commun. 250(4-6), 252–257 (2005). [CrossRef]

Fig. 7 Measured distributions of (a) BGS, and (b) BFS with the double-modulation scheme when the noise-floor compensation technique was employed (N_R = 5690).

5. Conclusion

In this paper, we developed a double-modulation scheme to mitigate the trade-off between the measurement range and the spatial resolution in BOCDR. In the experiment, 53-cm resolution and 1.5-km measurement range were simultaneously obtained. Furthermore, 27-cm resolution and 1.5-km measurement range were also simultaneously achieved when a noise-floor compensation technique was employed. We expect the double-modulation scheme will provide BOCDR with more feasibility as a fiber-optic nerve system in smart materials and structures.

Acknowledgments

The authors thank Mr. Koji Kajiwara at the University of Tokyo, Japan, for helpful discussions and comments. Yosuke Mizuno is grateful to the Japan Society for the Promotion of Science (JSPS) Research Fellowships for Young Scientists. This work was supported by the Grant-in-Aid for Scientific Research (S) and the Global Center of Excellence (G-COE) Program from the Ministry of Education, Culture, Sports, Science and Technology (MEXT), Japan.

References and links

1.	Y. Mizuno, W. Zou, Z. He, and K. Hotate, “Proposal of Brillouin optical correlation-domain reflectometry (BOCDR),” Opt. Express 16(16), 12148–12153 (2008). [CrossRef] [PubMed]
2.	Y. Mizuno, Z. He, and K. Hotate, “One-end-access high-speed distributed strain measurement with 13-mm spatial resolution based on Brillouin optical correlation-domain reflectometry,” IEEE Photon. Technol. Lett. 21(7), 474–476 (2009). [CrossRef]
3.	A. Fellay, L. Thevenaz, M. Facchini, M. Nikles, and P. Robert, “Distributed sensing using stimulated Brillouin scattering: towards ultimate resolution,” Proc. 12th Intern. Conf. Optical Fiber Sensors, 324–327 (1997).
4.	T. Kurashima, T. Horiguchi, H. Izumita, S. Furukawa, and Y. Koyamada, “Brillouin optical-fiber time domain reflectometry,” IEICE Trans. Commun,” E 76-B, 382–390 (1993).
5.	T. Horiguchi and M. Tateda, “BOTDA-nondestructive measurement of single-mode optical fiber attenuation characteristics using Brillouin interaction: theory,” J. Lightwave Technol. 7(8), 1170–1176 (1989). [CrossRef]
6.	Y. Koyamada, Y. Sakairi, N. Takeuchi, and S. Adachi, “Novel technique to improve spatial resolution in Brillouin optical time-domain reflectometry,” IEEE Photon. Technol. Lett. 19(23), 1910–1912 (2007). [CrossRef]
7.	W. Li, X. Bao, Y. Li, and L. Chen, “Differential pulse-width pair BOTDA for high spatial resolution sensing,” Opt. Express 16(26), 21616–21625 (2008). [CrossRef] [PubMed]
8.	Y. Mizuno, Z. He, and K. Hotate, “Measurement range enlargement in Brillouin optical correlation-domain reflectometry based on temporal gating scheme,” Opt. Express 17(11), 9040–9046 (2009). [CrossRef] [PubMed]
9.	K. Hotate and T. Hasegawa, “Measurement of Brillouin gain spectrum distribution along an optical fiber using a correlation-based technique – proposal, experiment and simulation,” IEICE Trans. Electron E 83-C, 405–412 (2000).
10.	K. Hotate and M. Tanaka, “Correlation-based continuous-wave technique for optical fiber distributed strain measurement using Brillouin scattering with cm-order spatial resolution – applications to smart materials,” IEICE Trans. Electron E 84-C, 1823–1828 (2001).
11.	G. P. Agrawal, Nonlinear Fiber Optics (Academic Press, California, 1995).
12.	T. Horiguchi, T. Kurashima, and M. Tateda, “Tensile strain dependence of Brillouin frequency shift in silica optical fibers,” IEEE Photon. Technol. Lett. 1(5), 107–108 (1989). [CrossRef]
13.	T. Kurashima, T. Horiguchi, and M. Tateda, “Thermal effects on the Brillouin frequency shift in jacketed optical silica fibers,” Appl. Opt. 29(15), 2219–2222 (1990). [CrossRef] [PubMed]
14.	K. Y. Song, Z. He, and K. Hotate, “Distributed strain measurement with millimeter-order spatial resolution based on Brillouin optical correlation domain analysis,” Opt. Lett. 31(17), 2526–2528 (2006). [CrossRef] [PubMed]
15.	Y. Mizuno, Z. He, and K. Hotate, “Stable entire-length measurement of fiber strain distribution by Brillouin optical correlation-domain reflectometry with polarization scrambling and noise-floor compensation,” Appl. Phys. Express 2, 062403 (2009). [CrossRef]
16.	Y. Ohtsuka, “Optical coherence effects on a fiber-sensing Fabry-Perot interferometer,” Appl. Opt. 21(23), 4316–4320 (1982). [CrossRef] [PubMed]
17.	A. W. Brown, M. D. DeMerchant, X. Bao, and T. W. Bremner, “Spatial resolution enhancement of a Brillouin-distributed sensor using a novel signal processing method,” J. Lightwave Technol. 17(7), 1179–1183 (1999). [CrossRef]
18.	M. P. Song and B. Zhao, “Accuracy enhancement in Brillouin scattering distributed temperature sensor based on Hilbert transform,” Opt. Commun. 250(4-6), 252–257 (2005). [CrossRef]

OCIS Codes
(060.2370) Fiber optics and optical communications : Fiber optics sensors
(290.5830) Scattering : Scattering, Brillouin
(280.4788) Remote sensing and sensors : Optical sensing and sensors

ToC Category:
Sensors

History
Original Manuscript: December 8, 2009
Revised Manuscript: March 1, 2010
Manuscript Accepted: March 3, 2010
Published: March 10, 2010

Citation
Yosuke Mizuno, Zuyuan He, and Kazuo Hotate, "Measurement range enlargement in Brillouin optical correlation-domain reflectometry based on double-modulation scheme," Opt. Express 18, 5926-5933 (2010)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-18-6-5926

Sort: Author | Year | Journal | Reset

References

Y. Mizuno, W. Zou, Z. He, and K. Hotate, “Proposal of Brillouin optical correlation-domain reflectometry (BOCDR),” Opt. Express 16(16), 12148–12153 (2008). [CrossRef] [PubMed]
Y. Mizuno, Z. He, and K. Hotate, “One-end-access high-speed distributed strain measurement with 13-mm spatial resolution based on Brillouin optical correlation-domain reflectometry,” IEEE Photon. Technol. Lett. 21(7), 474–476 (2009). [CrossRef]
A. Fellay, L. Thevenaz, M. Facchini, M. Nikles, and P. Robert, “Distributed sensing using stimulated Brillouin scattering: towards ultimate resolution,” Proc. 12th Intern. Conf. Optical Fiber Sensors, 324–327 (1997).
T. Kurashima, T. Horiguchi, H. Izumita, S. Furukawa, and Y. Koyamada, “Brillouin optical-fiber time domain reflectometry,” IEICE Trans. Commun,” E 76-B, 382–390 (1993).
T. Horiguchi and M. Tateda, “BOTDA-nondestructive measurement of single-mode optical fiber attenuation characteristics using Brillouin interaction: theory,” J. Lightwave Technol. 7(8), 1170–1176 (1989). [CrossRef]
Y. Koyamada, Y. Sakairi, N. Takeuchi, and S. Adachi, “Novel technique to improve spatial resolution in Brillouin optical time-domain reflectometry,” IEEE Photon. Technol. Lett. 19(23), 1910–1912 (2007). [CrossRef]
W. Li, X. Bao, Y. Li, and L. Chen, “Differential pulse-width pair BOTDA for high spatial resolution sensing,” Opt. Express 16(26), 21616–21625 (2008). [CrossRef] [PubMed]
Y. Mizuno, Z. He, and K. Hotate, “Measurement range enlargement in Brillouin optical correlation-domain reflectometry based on temporal gating scheme,” Opt. Express 17(11), 9040–9046 (2009). [CrossRef] [PubMed]
K. Hotate and T. Hasegawa, “Measurement of Brillouin gain spectrum distribution along an optical fiber using a correlation-based technique – proposal, experiment and simulation,” IEICE Trans. Electron E 83-C, 405–412 (2000).
K. Hotate and M. Tanaka, “Correlation-based continuous-wave technique for optical fiber distributed strain measurement using Brillouin scattering with cm-order spatial resolution – applications to smart materials,” IEICE Trans. Electron E 84-C, 1823–1828 (2001).
G. P. Agrawal, Nonlinear Fiber Optics (Academic Press, California, 1995).
T. Horiguchi, T. Kurashima, and M. Tateda, “Tensile strain dependence of Brillouin frequency shift in silica optical fibers,” IEEE Photon. Technol. Lett. 1(5), 107–108 (1989). [CrossRef]
T. Kurashima, T. Horiguchi, and M. Tateda, “Thermal effects on the Brillouin frequency shift in jacketed optical silica fibers,” Appl. Opt. 29(15), 2219–2222 (1990). [CrossRef] [PubMed]
K. Y. Song, Z. He, and K. Hotate, “Distributed strain measurement with millimeter-order spatial resolution based on Brillouin optical correlation domain analysis,” Opt. Lett. 31(17), 2526–2528 (2006). [CrossRef] [PubMed]
Y. Mizuno, Z. He, and K. Hotate, “Stable entire-length measurement of fiber strain distribution by Brillouin optical correlation-domain reflectometry with polarization scrambling and noise-floor compensation,” Appl. Phys. Express 2, 062403 (2009). [CrossRef]
Y. Ohtsuka, “Optical coherence effects on a fiber-sensing Fabry-Perot interferometer,” Appl. Opt. 21(23), 4316–4320 (1982). [CrossRef] [PubMed]
A. W. Brown, M. D. DeMerchant, X. Bao, and T. W. Bremner, “Spatial resolution enhancement of a Brillouin-distributed sensor using a novel signal processing method,” J. Lightwave Technol. 17(7), 1179–1183 (1999). [CrossRef]
M. P. Song and B. Zhao, “Accuracy enhancement in Brillouin scattering distributed temperature sensor based on Hilbert transform,” Opt. Commun. 250(4-6), 252–257 (2005). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Click here to see a list of articles that cite this paper