106.5 W high beam quality diode-side-pumped Nd:YAG laser at 1123 nm

doi:10.1364/OE.18.007923

106.5 W high beam quality diode-side-pumped Nd:YAG laser at 1123 nm

Li Chaoyang, Bo Yong, Yang Feng, Wang Zhichao, Xu Yiting, Wang Yuanbin, Gao Hongwei, Peng Qinjun, Cui Dafu, and Xu Zuyan »View Author Affiliations

Optics Express, Vol. 18, Issue 8, pp. 7923-7928 (2010)
http://dx.doi.org/10.1364/OE.18.007923

View Full Text Article

Acrobat PDF (438 KB)

Journal Search
Article Lookup

Article Tools

Citations

Alert me when this article is cited
Export Citation/Save

Article Navigation

▸ Article Outline
– Abstract
1. Introduction
2. Theoretical analysis
3. Experimental
4. Results and discussions
5. Conclusions
– References and links

Article Tools
Full Text
Article Info
References
Cited By
Figures
Metrics
Download PDF

Viewing Equations in the
HTML Article

Optimal Viewing Recommendations

Full Text
Article Info
References (20)
Cited By
Figures (7)
Metrics

Abstract

We demonstrate a diode-side-pumped continuous wave (CW) Nd:YAG laser at 1123 nm with over 100 W’s output power and good beam quality. The resonator adopts convex-convex structure working in a thermally near unstable cavity. By precise coating design a single 1123 nm wavelength is delivered. Under the pumped power of 870 W, an output power of 106.5 W is obtained, corresponding to an optical-optical conversion efficiency of 12.2%. The beam quality of M² factor is measured to be 5.6. To the best of our knowledge, this is the highest output power with good beam quality for 1123 nm CW Nd:YAG laser.

1. Introduction

The continuous wave (CW) lasers with output wavelength around 1.1 μm are widely studied in recent years due to its promising applications in laser display, biology, laser guide star etc. The wavelength region from 550 to 600 nm can be covered through frequency doubling technology from 1.1x μm solid-state lasers [1

E. Raikkonen, O. Kimmelma, M. Kaivola, and S. C. Buchter, “Passively Q-switched Nd:YAG/KTA laser at 561 nm,” Opt. Commun. 281(15-16), 4088–4091 (2008). [CrossRef]

–4

F. Q. Jia, Q. Zheng, Q. H. Xue, Y. K. Bu, and L. S. Qian, “Yellow light generation by frequency doubling of a diode-pumped Nd:YAG laser,” Opt. Commun. 259(1), 212–215 (2006). [CrossRef]

]. For example, frequency doubling 556 nm laser from 1112 nm Nd:YAG laser is suitable for laser display and lighting because it is proximate to 555 nm which is most sensitive to our eyes [4

F. Q. Jia, Q. Zheng, Q. H. Xue, Y. K. Bu, and L. S. Qian, “Yellow light generation by frequency doubling of a diode-pumped Nd:YAG laser,” Opt. Commun. 259(1), 212–215 (2006). [CrossRef]

]. An 1120 nm Raman fiber laser was used as a pump source for Raman fiber amplifier at 1178 nm, the latter can be frequency doubled to 589 nm for astronomy guide star [5

Y. Feng, L. R. Taylor, and D. B. Calia, “150 W highly-efficient Raman fiber laser,” Opt. Express 17(26), 23678–23683 (2009). [CrossRef]

]. The 1123nm line of the Nd:YAG crystal can be used as a pump source for thulium up conversion fiber lasers to generate blue light emission [6

Y. F. Chen and Y. P. Lan, “Diode-pumped passively Q-switched Nd:YAG laser at 1123 nm,” Appl. Phys. B 79(1), 29–31 (2004). [CrossRef]

Y. F. Chen, Y. P. Lan, and S. W. Tsai, “High power diode-pumped actively Q-switched Nd:YAG laser at 1123 nm,” Opt. Commun. 234(1-6), 309–313 (2004). [CrossRef]

]. Till now, different techniques have been developed to obtain 1.1x μm lasers, mainly including: solid-state lasers [1

E. Raikkonen, O. Kimmelma, M. Kaivola, and S. C. Buchter, “Passively Q-switched Nd:YAG/KTA laser at 561 nm,” Opt. Commun. 281(15-16), 4088–4091 (2008). [CrossRef]

–4

F. Q. Jia, Q. Zheng, Q. H. Xue, Y. K. Bu, and L. S. Qian, “Yellow light generation by frequency doubling of a diode-pumped Nd:YAG laser,” Opt. Commun. 259(1), 212–215 (2006). [CrossRef]

Y. F. Chen and Y. P. Lan, “Diode-pumped passively Q-switched Nd:YAG laser at 1123 nm,” Appl. Phys. B 79(1), 29–31 (2004). [CrossRef]

–13

S. S. Zhang, Q. P. Wang, X. Y. Zhang, Z. J. Liu, W. J. Sun, and S. W. Wang, “High power and highly efficient Nd:YAG laser emitting at 1123 nm,” Laser Phys. 19(12), 2159–2162 (2009). [CrossRef]

], fiber Raman lasers [5

Y. Feng, L. R. Taylor, and D. B. Calia, “150 W highly-efficient Raman fiber laser,” Opt. Express 17(26), 23678–23683 (2009). [CrossRef]

] and frequency conversion by stimulated Raman scattering effect [14

J. Findeisen, H. J. Eichler, and P. Peuser, “Self-stimulating, transversally diode-pumped Nd₃:KGd(WO₄)₂ Raman laser,” Opt. Commun. 181(1-3), 129–133 (2000). [CrossRef]

,15

P. Dekker, H. M. Pask, and J. A. Piper, “All-solid-state 704 mW continuous-wave yellow source based on an intracavity, frequency-doubled crystalline Raman laser,” Opt. Lett. 32(9), 1114–1116 (2007). [CrossRef] [PubMed]

]. In fact, there exist abundant laser lines around 1.1 μm in Nd:YAG materials which correspond to the Stark components of the ⁴F_3/2—⁴I_11/2 transition, such as 1112 nm,1116 nm and 1123 nm [16

S. Singh, R. G. Smith, and L. Van Uitert, “Stimulated emission cross section and fluorescent quantum efficiency of Nd³⁺ in yttrium aluminum garnet at room temperature,” Phys. Rev. B 10(6), 2566–2572 (1974). [CrossRef]

Concerning the 1123 nm Nd:YAG lasers, J. Marling [17

J. Marling, “1.05-1.44 μm tunablility and performance of the CW Nd³⁺:YAG laser,” IEEE J. Quantum Electron. 14(1), 56–62 (1978). [CrossRef]

] investigated 1123 nm CW laser using a 5 kW krypton arc-lamp as pump source in 1978, where about 30 W’s output power was obtained. In 1999, N. Moore et al. [18

N. Moore, W. A. Clarkson, D. C. Hanna, S. Lehmann, and J. Bösenberg, “Efficient operation of a diode-bar-pumped Nd:YAG laser on the low-gain 1123-nm line,” Appl. Opt. 38(27), 5761–5764 (1999). [CrossRef]

] reported a 1.7 W 1123 nm Nd:YAG laser by diode-end-pump. E.J.Zang et al. [11

E. Jun Zang, J. Ping Cao, Y. Li, T. Yang, and D. Mei Hong, “Single-frequency 1.25 W monolithic lasers at 1123 nm,” Opt. Lett. 32(3), 250–252 (2007). [CrossRef] [PubMed]

] developed a single frequency 1.25 W 1123 nm laser for stable coherent light sources study. Recently, S.S.Zhang et al. [12

S. S. Zhang, Q. P. Wang, X. Y. Zhang, Z. H. Cong, S. Z. Fan, Z. J. Liu, and W. J. Sun, “Continuous-wave ceramic Nd:YAG laser at 1123 nm,” Laser Phys. Lett. 6(12), 864–867 (2009). [CrossRef]

,13

S. S. Zhang, Q. P. Wang, X. Y. Zhang, Z. J. Liu, W. J. Sun, and S. W. Wang, “High power and highly efficient Nd:YAG laser emitting at 1123 nm,” Laser Phys. 19(12), 2159–2162 (2009). [CrossRef]

] demonstrated the diode-end-pumped CW 1123 nm laser both for ceramic Nd:YAG and composite Nd:YAG, the output power was 10.8 W and 9.3 W, respectively. Till now, the output power of diode-end-pumped 1123 nm Nd:YAG lasers was several Watts level.

Compared with the diode-end-pumped solid state laser, side-pumped-method has its advantages in obtaining both high output power and compact configuration. In present work, we report a diode-side-pumped CW 1123 nm Nd:YAG laser with high output power and high beam quality based on a simple convex-convex symmetrical cavity with precise coating design. The laser contains two laser modules with a five-fold symmetrical structure. Under the incident pump power of 870 W, the laser output power is up to 106.5 W, which corresponds to an optical-to-optical conversion efficiency of 12.2%. The beam quality factor M² is further measured to be 5.6 at the highest output power. This is the first time to demonstrate the 1123 nm laser with over 100 W output power and beam quality factor less than 10.

2. Theoretical analysis

As it is well known, several dozen laser transitions of Nd:YAG have been achieved up to the present. Most of the laser operation comes from the ⁴F_3/2→⁴I_9/2, ⁴I_11/2, and ⁴I_13/2 manifolds. Figure 1 shows the typical energy level diagram of Nd:YAG for these transitions. From the stimulated emission cross section data of Nd:YAG in Ref [16

], the 1123 nm transition has upper and lower laser levels within the same manifolds as the more familiar 1064 nm line, but it has the problem of a less peak stimulated emission cross section that is approximately 15 times smaller than for the 1064 nm. Compared with the other two strong transitions such as 1319 nm and 946 nm, the relative performance of the 1123 nm is about 3 and 2 times smaller, respectively. Hence, in order to obtain the laser oscillation at 1123 nm, not only 1064 nm oscillation, but also the 1319 nm and 946 nm must be restrained by means of high transmission output coupler.

Fig. 1 Typical energy level diagram of the Nd:YAG crystal

Another point should be emphasized that there exist three lines in a narrow region that are 1112 nm, 1116 nm and 1123 nm, respectively. They have relatively equal laser performance [16

]. However, the 1112 nm and 1116 nm lines could be suppressed through precise coating and the single 1123 nm Nd:YAG laser oscillation can be performed [13

S. S. Zhang, Q. P. Wang, X. Y. Zhang, Z. J. Liu, W. J. Sun, and S. W. Wang, “High power and highly efficient Nd:YAG laser emitting at 1123 nm,” Laser Phys. 19(12), 2159–2162 (2009). [CrossRef]

3. Experimental

The experimental setup was shown in Fig. 2 . The laser system has two laser modules, eachmodule contains a Nd:YAG rod with 4 mm diameter and 120 mm length, the doping concentration of Nd³⁺ is 0.6at%. For each laser module, a home-made 30 LD-bars array arranged in a five-fold symmetry around the laser crystal is served as the CW pump source operated at central wavelength of 808.5 nm. The total pump power for each module is 540 W. In order to get higher beam quality, the laser cavity adopts convex-convex symmetrical structure. Here, L1 is the distance from the mirror M1 to the left Nd:YAG rod end surface,L2 is the distance from the mirror M2 to the right Nd:YAG rod end surface. Both of them are set to be 150 mm, which form a symmetric resonator. L3 is the distance between the Nd:YAG rods to be 8 mm. The radius of curvature is 500 mm both for the rear mirror M1 and the output mirror M2. In our experiment, we took the method of coating technique to obtain 1123 nm output. M1 is coated with 99.8% high-reflection ratio at 1122.7 nm and antireflection at 1064 nm, 946 nm and 1319 nm. M2 is coated with 5% transmission ratio at 1122.7 nm and 85% for 1064 nm. In order to restrain the 1112 nm and 1116 nm oscillations, we measured the transmissions in the band range from 1050 to 1150 nm. The transmission ratio for 1112, 1116, and 1123 nm is 7.8%, 6.5% and 5%, respectively. For spectrum measurements, the laser was split through an attenuator mirror M3 (5% transmission ratio, incidence angle of 45°) into the spectrometer via an optical fiber. The output power was monitored by Ophir F300A power meter.

Fig. 2 The schematic diagram of the 1123nm Nd:YAG laser

4. Results and discussions

The primary consideration of resonator design is how to obtain a high output power while keeping a good beam quality. Firstly we used Gaussian light ABCD propagation matrix formulism of fundamental mode to optimize the cavity parameters. The components and the gain medium can be regarded as the separate elements in the function. Owing to the thermal effect, the laser material may be simplified to a lens with various focal length that shortens with the increase of absorbed pump power. The ABCD light propagation matrix for our laser structure is given as following:

M (f t) = (\begin{matrix} 1 & L 2^{'} \\ 0 & 1 \end{matrix}) . (\begin{matrix} 1 & 0 \\ \frac{- 2}{R 2} & 1 \end{matrix}) . (\begin{matrix} 1 & L 2^{'} \\ 0 & 1 \end{matrix}) . (\begin{matrix} 1 & 0 \\ \frac{- 1}{f t} & 1 \end{matrix}) . (\begin{matrix} 1 & L 3' \\ 0 & 1 \end{matrix}) . (\begin{matrix} 1 & 0 \\ \frac{- 1}{f t} & 1 \end{matrix}) . (\begin{matrix} 1 & L 1^{'} \\ 0 & 1 \end{matrix}) . (\begin{matrix} 1 & 0 \\ \frac{- 2}{R 1} & 1 \end{matrix}) . (\begin{matrix} 1 & L 1^{'} \\ 0 & 1 \end{matrix}) .. (\begin{matrix} 1 & 0 \\ \frac{- 1}{f t} & 1 \end{matrix}) . (\begin{matrix} 1 & L 3^{'} \\ 0 & 1 \end{matrix}) . (\begin{matrix} 1 & 0 \\ \frac{- 1}{f t} & 1 \end{matrix}) = (\begin{matrix} A & B \\ C & D \end{matrix})

(1)

Where, ft is the thermal focal length of the gain medium. L1’, L2’ and L3′ is the optical path after considering the refractive index of Nd:YAG material, respectively. R1 and R2 is the curvature radium of the mirror M1 and M2. The calculated beam size at the center of the second laser rod is:

ω = \sqrt{\frac{2 λ}{π}} . \frac{B^{0.5}}{{[4 - {(A + D)}^{2}]}^{0.25}}

(2)

Figure 3 shows the simulation result for the calculated fundamental mode radius at the center of the laser rod as a function of thermal focal length. According to the theory in Ref [19

Y. Feng, Y. Bi, Z. Y. Xu, and G. Y. Zhang, “Thermally-near-unstable resonator design for solid state lasers,” Proc. SPIE 4969, 227–232 (2003). [CrossRef]

], a good light beam quality can be obtained without output power reducing when laser operates in thermally-near unstable zone, i.e., the border of the stable region.

Fig. 3 Fundamental laser mode size with the thermal focal length

For the diode-side-pumped solid-state laser, the laser material absorbs the pump laser energy, and the thermal loading leads to a lens behavior in the gain medium. To determine the thermal focal length of the single laser module, we constructed a short plano-plano resonator and used the method suggested by D.G.Lancaster [20

D. G. Lancaster and J. M. Dawes, “Thermal lens measurement of a quasi steady-state repetitively flashlamp-pumped Cr,Tm,Ho:YAG laser,” Opt. Laser Technol. 30(2), 103–108 (1998). [CrossRef]

]. Figure 4 shows the dependence of measured thermal focal length for single laser module on the pump power. As an example, the thermal focal length is 231mm at the pump power of 435W where the maximum output power is acquired in our experiment. Then the cavity parameters could be designed and optimized by the simulation results.

Fig. 4 Measured thermal focal length against the pump power for single laser module

We measured the average output power of the 1123 nm Nd:YAG laser as a function of the incident pump power, the result is shown in Fig. 5 . It can be seen that the threshold isabout 330W. Following,the output power increases approximate linearly with the incident pump power. We observed a roll-over effect, i.e. the output power increases up to a maximum then falls with the increase of the pump power. While the laser operated with thermally near unstable zone at pump power of 870W, the maximum output power is 106.5 W corresponding to an optical-optical efficiency of 12.2%. The drop in the output power is contributed to the thermal lens effect that causes the laser working into the unstable zone. We also measured the power stability at the highest output power in every 5 minutes. The fluctuation of laser output power was ± 2.1% over 30 minutes.

Fig. 5 The output power at 1123nm versus the incident pump power

The laser spectrum was determined by an Anritsu laser spectrometer (Anritsu MS9710B). Under the output power of 106.5W, the measured spectrum is shown in Fig. 6 . It can be seenthat only 1123 nm line exists. The 1112 nm and 1116 nm wavelength nearby does not appear, which indicates the wavelength selectivity is achieved through precise coating.

Fig. 6 The spectrum of the 1123nm laser at output power of 106.5 W

We tested the beam quality of 1112 nm laser by a Spiricon M2-200 laser beam analyzer using the second moment method as shown in Fig. 7 . The inserted image is the 3D intensity distribution of the beam. The M² value was measured to be 5.6 at the output power of 106.5W.

Fig. 7 M² measurements of 1123nm beam under the maximal output power.

The upper right is its 3D intensity distribution From the beam spatial intensity distribution it is clearly seen that the laser operates in a Quasi-Gaussian mode. This beam quality is enough for most applications.

5. Conclusions

In conclusion, we demonstrate a diode-side-pumped CW 1123 nm laser with high output power and high beam quality based on Nd:YAG crystal. The cavity adopts convex-convex configuration. Through precise coating the laser delivers single 1123nm wavelength. Under the pump power of 870 W, an output power of 106.5 W with M²=5.6 is obtained, corresponding to an optical-optical conversion of 12.2%. As far as we know, this is the first time to report over 100W and beam quality of 5.6 for 1123nm Nd:YAG laser by diode-side-pumped method.

Acknowledgements

The authors thank the support of the National High Technology Research and Development Program (“863”Program) of China under contract No.2006AA030103 and Major Program of the National Natural Science Foundation of China with No.50990304.

References and links

1.	E. Raikkonen, O. Kimmelma, M. Kaivola, and S. C. Buchter, “Passively Q-switched Nd:YAG/KTA laser at 561 nm,” Opt. Commun. 281(15-16), 4088–4091 (2008). [CrossRef]
2.	Q. Zheng, Y. Yao, D. P. Qu, K. Zhou, Y. Liu, and L. Zhao, “All-solid-state 556 nm yellow-green laser generated by frequency doubling of a diode-pumped Nd:YAG laser,” J. Opt. Soc. Am. B 26(10), 1939–1943 (2009). [CrossRef]
3.	Y. Yao, Q. Zheng, D. P. Qu, K. Zhou, Y. Liu, and L. Zhao, “All-solid-state continuous-wave frequency-doubled Nd:YAG/LBO laser with 1.2 W output power at 561 nm,” Laser Phys. Lett. 6, 112–115 (2009).
4.	F. Q. Jia, Q. Zheng, Q. H. Xue, Y. K. Bu, and L. S. Qian, “Yellow light generation by frequency doubling of a diode-pumped Nd:YAG laser,” Opt. Commun. 259(1), 212–215 (2006). [CrossRef]
5.	Y. Feng, L. R. Taylor, and D. B. Calia, “150 W highly-efficient Raman fiber laser,” Opt. Express 17(26), 23678–23683 (2009). [CrossRef]
6.	Y. F. Chen and Y. P. Lan, “Diode-pumped passively Q-switched Nd:YAG laser at 1123 nm,” Appl. Phys. B 79(1), 29–31 (2004). [CrossRef]
7.	Y. F. Chen, Y. P. Lan, and S. W. Tsai, “High power diode-pumped actively Q-switched Nd:YAG laser at 1123 nm,” Opt. Commun. 234(1-6), 309–313 (2004). [CrossRef]
8.	J. Y. Huang, H. C. Liang, K. W. Su, H. C. Lai, Y. F. Chen, and K. F. Huang, “InGaAs quantum-well saturable absorbers for a diode-pumped passively Q-switched Nd:YAG laser at 1123 nm,” Appl. Opt. 46(2), 239–242 (2007). [CrossRef] [PubMed]
9.	X. P. Guo, M. Chen, G. Li, B. Y. Zhang, J. D. Yang, Z. G. Zhang, and Y. G. Wang, “Diode-pumped 1123 nm Nd:YAG laser,” Chin. Opt. Lett. 2, 402–404 (2004).
10.	Zh. Q. Cai, M. Chen, Zh. G. Zhang, R. Zhou, W. Q. Wen, X. Ding, and J. Q. Yao, “Diode-end-pumped 1123 nm Nd:YAG laser with 2.6 W output power,” Chin. Opt. Lett. 3, 281–283 (2005).
11.	E. Jun Zang, J. Ping Cao, Y. Li, T. Yang, and D. Mei Hong, “Single-frequency 1.25 W monolithic lasers at 1123 nm,” Opt. Lett. 32(3), 250–252 (2007). [CrossRef] [PubMed]
12.	S. S. Zhang, Q. P. Wang, X. Y. Zhang, Z. H. Cong, S. Z. Fan, Z. J. Liu, and W. J. Sun, “Continuous-wave ceramic Nd:YAG laser at 1123 nm,” Laser Phys. Lett. 6(12), 864–867 (2009). [CrossRef]
13.	S. S. Zhang, Q. P. Wang, X. Y. Zhang, Z. J. Liu, W. J. Sun, and S. W. Wang, “High power and highly efficient Nd:YAG laser emitting at 1123 nm,” Laser Phys. 19(12), 2159–2162 (2009). [CrossRef]
14.	J. Findeisen, H. J. Eichler, and P. Peuser, “Self-stimulating, transversally diode-pumped Nd₃:KGd(WO₄)₂ Raman laser,” Opt. Commun. 181(1-3), 129–133 (2000). [CrossRef]
15.	P. Dekker, H. M. Pask, and J. A. Piper, “All-solid-state 704 mW continuous-wave yellow source based on an intracavity, frequency-doubled crystalline Raman laser,” Opt. Lett. 32(9), 1114–1116 (2007). [CrossRef] [PubMed]
16.	S. Singh, R. G. Smith, and L. Van Uitert, “Stimulated emission cross section and fluorescent quantum efficiency of Nd³⁺ in yttrium aluminum garnet at room temperature,” Phys. Rev. B 10(6), 2566–2572 (1974). [CrossRef]
17.	J. Marling, “1.05-1.44 μm tunablility and performance of the CW Nd³⁺:YAG laser,” IEEE J. Quantum Electron. 14(1), 56–62 (1978). [CrossRef]
18.	N. Moore, W. A. Clarkson, D. C. Hanna, S. Lehmann, and J. Bösenberg, “Efficient operation of a diode-bar-pumped Nd:YAG laser on the low-gain 1123-nm line,” Appl. Opt. 38(27), 5761–5764 (1999). [CrossRef]
19.	Y. Feng, Y. Bi, Z. Y. Xu, and G. Y. Zhang, “Thermally-near-unstable resonator design for solid state lasers,” Proc. SPIE 4969, 227–232 (2003). [CrossRef]
20.	D. G. Lancaster and J. M. Dawes, “Thermal lens measurement of a quasi steady-state repetitively flashlamp-pumped Cr,Tm,Ho:YAG laser,” Opt. Laser Technol. 30(2), 103–108 (1998). [CrossRef]

OCIS Codes
(140.3480) Lasers and laser optics : Lasers, diode-pumped
(140.3580) Lasers and laser optics : Lasers, solid-state

ToC Category:
Lasers and Laser Optics

History
Original Manuscript: January 28, 2010
Revised Manuscript: March 5, 2010
Manuscript Accepted: March 8, 2010
Published: March 31, 2010

Citation
Li Chaoyang, Bo Yong, Yang Feng, Wang Zhichao, Xu Yiting, Wang Yuanbin, Gao Hongwei, Peng Qinjun, Cui Dafu, and Xu Zuyan, "106.5 W high beam quality diode-side-pumped Nd:YAG laser at 1123 nm," Opt. Express 18, 7923-7928 (2010)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-18-8-7923

Sort: Author | Year | Journal | Reset

References

E. Raikkonen, O. Kimmelma, M. Kaivola, and S. C. Buchter, “Passively Q-switched Nd:YAG/KTA laser at 561 nm,” Opt. Commun. 281(15-16), 4088–4091 (2008). [CrossRef]
Q. Zheng, Y. Yao, D. P. Qu, K. Zhou, Y. Liu, and L. Zhao, “All-solid-state 556 nm yellow-green laser generated by frequency doubling of a diode-pumped Nd:YAG laser,” J. Opt. Soc. Am. B 26(10), 1939–1943 (2009). [CrossRef]
Y. Yao, Q. Zheng, D. P. Qu, K. Zhou, Y. Liu, and L. Zhao, “All-solid-state continuous-wave frequency-doubled Nd:YAG/LBO laser with 1.2 W output power at 561 nm,” Laser Phys. Lett. 6, 112–115 (2009).
F. Q. Jia, Q. Zheng, Q. H. Xue, Y. K. Bu, and L. S. Qian, “Yellow light generation by frequency doubling of a diode-pumped Nd:YAG laser,” Opt. Commun. 259(1), 212–215 (2006). [CrossRef]
Y. Feng, L. R. Taylor, and D. B. Calia, “150 W highly-efficient Raman fiber laser,” Opt. Express 17(26), 23678–23683 (2009). [CrossRef]
Y. F. Chen and Y. P. Lan, “Diode-pumped passively Q-switched Nd:YAG laser at 1123 nm,” Appl. Phys. B 79(1), 29–31 (2004). [CrossRef]
Y. F. Chen, Y. P. Lan, and S. W. Tsai, “High power diode-pumped actively Q-switched Nd:YAG laser at 1123 nm,” Opt. Commun. 234(1-6), 309–313 (2004). [CrossRef]
J. Y. Huang, H. C. Liang, K. W. Su, H. C. Lai, Y. F. Chen, and K. F. Huang, “InGaAs quantum-well saturable absorbers for a diode-pumped passively Q-switched Nd:YAG laser at 1123 nm,” Appl. Opt. 46(2), 239–242 (2007). [CrossRef] [PubMed]
X. P. Guo, M. Chen, G. Li, B. Y. Zhang, J. D. Yang, Z. G. Zhang, and Y. G. Wang, “Diode-pumped 1123 nm Nd:YAG laser,” Chin. Opt. Lett. 2, 402–404 (2004).
Zh. Q. Cai, M. Chen, Zh. G. Zhang, R. Zhou, W. Q. Wen, X. Ding, and J. Q. Yao, “Diode-end-pumped 1123 nm Nd:YAG laser with 2.6 W output power,” Chin. Opt. Lett. 3, 281–283 (2005).
E. Jun Zang, J. Ping Cao, Y. Li, T. Yang, and D. Mei Hong, “Single-frequency 1.25 W monolithic lasers at 1123 nm,” Opt. Lett. 32(3), 250–252 (2007). [CrossRef] [PubMed]
S. S. Zhang, Q. P. Wang, X. Y. Zhang, Z. H. Cong, S. Z. Fan, Z. J. Liu, and W. J. Sun, “Continuous-wave ceramic Nd:YAG laser at 1123 nm,” Laser Phys. Lett. 6(12), 864–867 (2009). [CrossRef]
S. S. Zhang, Q. P. Wang, X. Y. Zhang, Z. J. Liu, W. J. Sun, and S. W. Wang, “High power and highly efficient Nd:YAG laser emitting at 1123 nm,” Laser Phys. 19(12), 2159–2162 (2009). [CrossRef]
J. Findeisen, H. J. Eichler, and P. Peuser, “Self-stimulating, transversally diode-pumped Nd3:KGd(WO4)2 Raman laser,” Opt. Commun. 181(1-3), 129–133 (2000). [CrossRef]
P. Dekker, H. M. Pask, and J. A. Piper, “All-solid-state 704 mW continuous-wave yellow source based on an intracavity, frequency-doubled crystalline Raman laser,” Opt. Lett. 32(9), 1114–1116 (2007). [CrossRef] [PubMed]
S. Singh, R. G. Smith, and L. Van Uitert, “Stimulated emission cross section and fluorescent quantum efficiency of Nd3+ in yttrium aluminum garnet at room temperature,” Phys. Rev. B 10(6), 2566–2572 (1974). [CrossRef]
J. Marling, “1.05-1.44 μm tunablility and performance of the CW Nd3+:YAG laser,” IEEE J. Quantum Electron. 14(1), 56–62 (1978). [CrossRef]
N. Moore, W. A. Clarkson, D. C. Hanna, S. Lehmann, and J. Bösenberg, “Efficient operation of a diode-bar-pumped Nd:YAG laser on the low-gain 1123-nm line,” Appl. Opt. 38(27), 5761–5764 (1999). [CrossRef]
Y. Feng, Y. Bi, Z. Y. Xu, and G. Y. Zhang, “Thermally-near-unstable resonator design for solid state lasers,” Proc. SPIE 4969, 227–232 (2003). [CrossRef]
D. G. Lancaster and J. M. Dawes, “Thermal lens measurement of a quasi steady-state repetitively flashlamp-pumped Cr,Tm,Ho:YAG laser,” Opt. Laser Technol. 30(2), 103–108 (1998). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Click here to see a list of articles that cite this paper