OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 19, Iss. 10 — May. 9, 2011
  • pp: 9050–9055
« Show journal navigation

Polarization independent broadband reflectors based on cross-stacked gratings

Deyin Zhao, Hongjun Yang, Zhenqiang Ma, and Weidong Zhou  »View Author Affiliations


Optics Express, Vol. 19, Issue 10, pp. 9050-9055 (2011)
http://dx.doi.org/10.1364/OE.19.009050


View Full Text Article

Acrobat PDF (829 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We report here a broadband reflector based on a two cross-stacked grating structure. This type of broadband reflector is polarization-independent, with ~100% reflectance over a designed spectral range of 1.4 to 1.6μm. The reflection phase differences between TE and TM polarizations remain almost a constant value of 1.2π over the same high reflection spectral range. The reflector performance tolerance was also investigated by varying the grating structure parameters. Two types of Fabry-Perot cavities can be configured based on two cross-stacked grating structures, for both polarization independent and polarization dependent resonance cavity mode control. All these characteristics associated with the cross-stacked grating reflectors enable a new type of resonant cavity or wave plate design for a large range of photonic applications.

© 2011 OSA

1. Introduction

In this work, we propose a new type of grating framework with two cross-stacked SWG layers to realize polarization independent reflectors, with relatively simple fabrication processes. In what follows, we first study the reflection spectra and the reflection phase response for different TE and TM polarized incident light, using the finite difference time domain (FDTD) method. Secondly, we investigate the influences on the reflection and phase of different grating structure parameters for practical applications. Finally, we demonstrate the features of the resonant modes inside the FP cavities composed of such cross-stacked SWG reflectors.

2. Reflectivity and polarization of cross-stacked grating broadband reflectors

We first consider a single layer SWG (sl-SWG, or HCG) formed by silicon with the refractive index nSi = 3.48, the thickness t = 240nm, the period Λ = 980nm and the fill factor f = 0.2, as show in Fig. 1(a)
Fig. 1 (a) and (c): Sketches of the subwavelength grating Fano reflectors with a single layer and two cross-stacked layers, respectively; (b) and (d): The reflections of TE(dash lines) and TM(solid lines) polarization of sl-SWG and cs-SWG, respectively.
. The grating strip direction is aligned along Y axis. Under normal incidence, the reflection of this sl-SWG is polarization sensitive, as displayed in Fig. 1(b), where only TE wave (E field is parallel to the grating strip, y direction) has a flat-broad and very high reflectance in the wavelength range of 1.2 to 1.6μm. If such a sl-SWG is cross-stacked onto another one, we expect to form a polarization-independent reflector according to the rotation symmetry for both TE and TM incident waves. Figure 1(c) shows the geometry of two cross-stacked SWGs (cs-SWGs). The two sl-SWGs can have different grating thicknesses, periods and fill factors. Of course, for such a cs-SWG, it is not rigorous symmetric in the same plane. The two sl-SWGs will influence each other. In order to obtain a broad high reflection band for both TE and TM polarizations, we can tune and choose the proper grating structure parameters. For example, here we choose the thickness t1 = t2 = 230nm, the period Λ1 = Λ2 = 980nm and the fill factor f1 = f2 = 0.2. Figure 1(d) demonstrates the ultra-high and broadband reflections for both TE and TM polarizations at different incident azimuth angles (ψ) in xy plane. One can clearly find that the reflections of all the cases overlap with each other, which indicates such a cs-SWG can function as a polarization independent reflector, similar to the 2D PC slab reflectors [13

13. V. Lousse, W. Suh, O. Kilic, S. Kim, O. Solgaard, and S. Fan, “Angular and polarization properties of a photonic crystal slab mirror,” Opt. Express 12(8), 1575–1582 (2004). [CrossRef] [PubMed]

]. In addition, it can also be seen that, comparing to sl-SWG, the reflection band of cs-SWGs becomes narrower due to the interactions between two sl-SWGs.

3. Reflection phase properties of cs-SWGs

The polarization-independent reflection in cs-SWGs is based on the cross-stacking of two individual polarization-dependent sl-SWGs, i.e., TE and TM waves are reflected by the bottom and the top sl-SWGs, respectively (more discussions in Section 4). These two sl-SWGs are not in the same plane. Hence the reflected light undergoes different optical path lengths. The reflection phase ϕR must not be the same for two polarizations, similar as the structures in [11

11. R. Magnusson, M. Shokooh-Saremi, and E. G. Johnson, “Guided-mode resonant wave plates,” Opt. Lett. 35(14), 2472–2474 (2010). [CrossRef] [PubMed]

]. We investigate ϕR of cs-SWGs, following a similar calculation procedure reported in [15

15. D. Zhao, Z. Ma, and W. Zhou, “Design of dielectric photonic crystal reflector Fabry-Perot cavities,” Proc. SPIE 7756, 775610 (2010). [CrossRef]

].

Figure 2(a)
Fig. 2 Simulated reflection amplitude R for both TE (red dash lines) and TM (blue solid lines) polarizations, simulated reflection phase ϕR for TE (red dash lines with square holes) and TM (blue dash lines with circle holes), as well as the calculated phase difference between TE and TM |ϕTE - ϕTM| (black dash lines with triangle holes) for cs-SWG structures with Si thickness t1 = t2 = 230nm, grating period Λ = 980nm, fill factors f1 = 0.2, and different fill factors f2: (a) f2 = 0.2; (b) f2 = 0.18; (c) f2 = 0.22.
shows the calculated reflection phases of the cs-SWG, for both TE and TM polarizations. As a reference, the reflection amplitude R is also shown. One can see, in the spectral range of 1.4 to 1.65μm, ϕTE increases from 1.4π to 2π, while ϕTM increases from 0.2π to 0.7π. Although ϕTE and ϕTM have different spectral profiles, their difference |ϕTE - ϕTM| almost keeps a constant 1.2π in the entire high reflection band. This suggests that, the reflected TM polarization light has a phase retard of 1.2π than the reflected TE polarization light. If such a cs-SWG is used as a wave plate, it will results in a linear-to-ellipse polarization conversion.

4. Influences of the grating fill factor, thickness, period and substrate

Here we investigate the proposed cs-SWG performance tolerance by varying grating structure parameters, such as the grating fill factors, thicknesses and periods, as well as different substrates. We will also investigate hybrid cs-SWG structures where two sl-SWGs have different structural parameters.

Figures 2(b) and 2(c) demonstrate the reflection amplitude and phase response with changing fill factor f2. For t1 = t2 = 230nm, Λ1 = Λ2 = 980nm, f1 = 0.2 and f2 = 0.18, the results are plotted in Fig. 2(b). We can find the overlapped high reflection spectra for both TE and TM polarizations still remain broad and flat. Compared to Fig. 2(a), RTE and RTM have an obvious blue shift due to the effective refractive index reduction. When f2 increases to 0.22, the overlapped RTE and RTM with high and broadband spectra can be also obtained, as seen in Fig. 2(c). In this case, RTE and RTM have an obvious red shift due to the effective refractive index increase. Comparing these three cases, one can also find another interesting features of RTE and RTM. For f1≠f2, the overlap between RTE and RTM is better than that of f1 = f2. It can be regarded that the asymmetry in the grating fill factor in these two sl-SWGs compensates their rotation asymmetry to some extent.

The Si layer thickness influence on the reflection was also investigated. The results are shown in Fig. 3
Fig. 3 Reflection of TE (red dash lines) and TM (blue solid lines) polarizations at t1 = 230nm, Λ1 = Λ2 = 980nm, f1 = f2 = 0.2: (a) t2 = 220nm; (b) t2 = 230nm; (c) t2 = 240nm.
. Here, we change the Si layer thickness t2 from 220nm to 240nm and keep the grating fill factor f1 = f2 = 0.2, t1 = 230nm, and grating period Λ1 = Λ2 = 980nm. For all three cases shown in Fig. 3, polarization independent TE/TM reflection band can be obtained over a large spectral range (1400-1520nm). One can also find RTM bandedge shifts (red-shift with increase in thickness) much fast with the change of t2, while RTE bandedge almost does not shift. This indicates that the thickness of t2, has a more profound influence on RTM. We can also obtain a better overlap in the high reflection spectra region between RTE and RTM by choosing an optimal t2 value. Note t1≠t2 here. Different thicknesses also compensate the rotational asymmetry. Figure 3(c) shows that when t2>240nm (large thickness variation), the overlapped region of RTE and RTM begins to reduce.

The grating period variation also impacts the reflection overlapping profile. The results are shown in Fig. 4
Fig. 4 Reflection of TE(red dash lines) and TM(blue solid lines) polarizations at Λ1 = 980nm, t1 = t2 = 230nm, f1 = f2 = 0.2: (a) Λ2 = 960nm; (b) Λ2 = 980nm; (c) Λ2 = 1000nm.
, where the grating period Λ2 varies from 960nm to 1000nm, f1 = f2 = 0.2, t1 = t2 = 230nm, and Λ1 = 980nm. As Λ2 increases, both TE and TM reflection spectra shifts towards longer wavelengths (red-shift), with RTE bandedge moves much faster than RTM bandedge. This may mostly be due to the fact that the period Λ2 has a much larger impact on RTE.

Typically, these SWG structures can be fabricated directly on SOI (silicon on insulator) substrates, as well being transferred via a crystalline semiconductor nanomenbrane stamp process onto other foreign substrates, such as glass substrate, etc [16

16. W. Zhou, Z. Ma, H. Yang, Z. Qiang, G. Qin, H. Pang, L. Chen, W. Yang, S. Chuwongin, and D. Zhao, “Flexible photonic-crystal Fano filters based on transferred semiconductor nanomembranes,” J. Phys. D 42(23), 234007 (2009). [CrossRef]

]. Considering practical applications, we consider cs-SWG structures on these two types of substrates: glass and SOI. The results with glass (nSiO2 = 1.48) and SOI substrates are shown in Figs. 5(a)
Fig. 5 Reflection of TE (red dash lines) and TM (blue solid lines) polarizations at t1 = t2 = 230nm, Λ = 980nm, f1 = f2 = 0.2: (a) with glass substrate; (b) with SOI substrate.
and 5(b), respectively, where t1 = t2 = 230nm, Λ1 = Λ2 = 980nm, f1 = f2 = 0.2, and the SiO2 BOX (buried oxide) layer thickness for SOI substrate is optimally chosen to be 1.2μm. Due to the introduction of substrate, the reflection spectra are red shift and the overlapped high flat RTE and RTM band still covers the broad wavelength range from 1.45 to 1.65μm. Of course, the SiO2 thickness also influences the reflection performance of such cs-SWGs reflectors with SOI substrate. From the above results, one can find the proposed cs-SWG reflector structure has a reasonably large design and fabrication tolerances.

5. Resonant modes in FP cavities composed of two cs-SWGs

Inside FtB FP cavity, if the incident light is TE (or TM) mode with respect to the bottom cs-SWG, then the reflected wave shall be TM (or TE) mode with respect to the upper cs-SWG. Hence, for light travelling inside the FP cavity in a complete round-trip, the total reflection phase change shall be the same for both TE and TM modes. Consequently, the resonant mode inside FtB FP cavity is polarization independent. For an example, we choose the cavity length Lc = 6μm. The resonant cavity mode is found according to the phase resonant condition of FP cavity, 4πLc/λΦTE(λ)ΦTM(λ)=m2πif m is equal to an integer, as shown in Fig. 6(c). The resonant TE/TM modes overlap at 1490nm.

On the other hand, for the light travelling inside FtF FP cavity, the reflected wave remains the same polarization with respect to both reflectors. According to the phase resonant condition, the resonant TE and TM modes are completely different, as shown in Fig. 6(d), due to different ϕTE and ϕTM values, even although such cavities have same reflection amplitude and the cavity length.

6. Conclusion

In conclusion, we have investigated the reflection amplitude and the reflection phase properties of the proposed two cross-stacked subwavelength grating reflectors. Comparing to the single layer SWG reflectors, this type of cs-SWG reflectors not only keep high reflectance, flat-broad reflection band, but also are realized to be polarization independent according to rotation symmetry of TE and TM mode under normal incident. Due to the absence of full symmetry in structure, similar to other types of multilayer SWGs, the reflection phase of such two cross-stacked SWG reflectors is still polarization dependent, though the differences in TE/TM polarization reflection phase remain to be a constant over the entire broadband reflection band. With proper design of the FP cavity based on the proposed cs-SWG reflectors, it is possible to achieve polarization independent design as well. All the results and conclusions can be very helpful for such kind of cs-SWG reflectors into a wide range of photonic applications.

Acknowledgments

This work is supported in part by the United States Air Force Office of Scientific Research (USAFOSR) MURI program under Grant FA9550-08-1-0337, by USAFOSR under grant FA9550-09-C-0200, and in part by the United States Army Research Office (USARO) under Grant W911NF-09-1-0505.

References and links

1.

U. Fano, “Effects of configuration interaction on intensities and phase shifts,” Phys. Rev. B 124(6), 1866–1878 (1961). [CrossRef]

2.

S. Fan and J. D. Joannopoulos, “Analysis of guided resonances in photonic crystal slabs,” Phys. Rev. B 65(23), 235112 (2002). [CrossRef]

3.

R. Magnusson and M. Shokooh-Saremi, “Physical basis for wideband resonant reflectors,” Opt. Express 16(5), 3456–3462 (2008). [CrossRef] [PubMed]

4.

S. T. Thurman and G. M. Morris, “Controlling the spectral response in guided-mode resonance filter design,” Appl. Opt. 42(16), 3225–3233 (2003). [CrossRef] [PubMed]

5.

C. F. R. Mateus, M. C. Y. Huang, L. Chen, C. J. Chang-Hasnain, and Y. Suzuki, “Broadband mirror (1.12-1.62μm) using single-layer sub-wavelength grating,” IEEE Photon. Technol. Lett. 16(7), 1676–1678 (2004). [CrossRef]

6.

T. Sang, L. Wang, S. Ji, Y. Ji, H. Chen, and Z. Wang, “Systematic study of the mirror effect in a poly-Si subwavelength periodic membrane,” J. Opt. Soc. Am. A 26(3), 559–565 (2009). [CrossRef]

7.

Y. Zhou, M. C. Y. Huang, C. Chase, V. Karagodsky, M. Moewe, B. Pesala, F. G. Sedgwick, and C. J. Chang-Hasnain, “High-index-contrast grating (HCG) and its applications in optoelectronic devices,” IEEE J. Sel. Top. Quantum Electron. 15(5), 1485–1499 (2009). [CrossRef]

8.

M. Shokooh-Saremi and R. Magnusson, “Leaky-mode resonant reflectors with extreme bandwidths,” Opt. Lett. 35(8), 1121–1123 (2010). [CrossRef] [PubMed]

9.

M. C. Y. Huang, Y. Zhou, and C. J. Chang-Hasnain, “A surface-emitting laser incorporating a high indexcontrast subwavelength grating,” Nat. Photonics 1(2), 119–122 (2007). [CrossRef]

10.

S. Boutami, B. Ben Bakir, P. Regreny, J. L. Leclercq, and P. Viktorovitch, “Compact 1.55 µm room-temperature optically pumped VCSEL using photonic crystal mirror,” Electron. Lett. 43(5), 282–283 (2007). [CrossRef]

11.

R. Magnusson, M. Shokooh-Saremi, and E. G. Johnson, “Guided-mode resonant wave plates,” Opt. Lett. 35(14), 2472–2474 (2010). [CrossRef] [PubMed]

12.

D. Fattal, J. Li, Z. Peng, M. Fiorentino, and R. G. Beausoleil, “Flat dielectric grating reflectors with focusing abilities,” Nat. Photonics 4(7), 466–470 (2010). [CrossRef]

13.

V. Lousse, W. Suh, O. Kilic, S. Kim, O. Solgaard, and S. Fan, “Angular and polarization properties of a photonic crystal slab mirror,” Opt. Express 12(8), 1575–1582 (2004). [CrossRef] [PubMed]

14.

H. Wu, W. Mo, J. Hou, D. Gao, R. Hao, H. Jiang, R. Guo, W. Wu, and Z. Zhou, “A high performance polarization independent reflector based on a multilayered configuration grating structure,” J. Opt. 12(4), 045703 (2010). [CrossRef]

15.

D. Zhao, Z. Ma, and W. Zhou, “Design of dielectric photonic crystal reflector Fabry-Perot cavities,” Proc. SPIE 7756, 775610 (2010). [CrossRef]

16.

W. Zhou, Z. Ma, H. Yang, Z. Qiang, G. Qin, H. Pang, L. Chen, W. Yang, S. Chuwongin, and D. Zhao, “Flexible photonic-crystal Fano filters based on transferred semiconductor nanomembranes,” J. Phys. D 42(23), 234007 (2009). [CrossRef]

OCIS Codes
(050.2770) Diffraction and gratings : Gratings
(050.5080) Diffraction and gratings : Phase shift
(140.3948) Lasers and laser optics : Microcavity devices
(050.6624) Diffraction and gratings : Subwavelength structures

ToC Category:
Diffraction and Gratings

History
Original Manuscript: February 11, 2011
Revised Manuscript: March 28, 2011
Manuscript Accepted: April 18, 2011
Published: April 25, 2011

Citation
Deyin Zhao, Hongjun Yang, Zhenqiang Ma, and Weidong Zhou, "Polarization independent broadband reflectors based on cross-stacked gratings," Opt. Express 19, 9050-9055 (2011)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-19-10-9050


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. U. Fano, “Effects of configuration interaction on intensities and phase shifts,” Phys. Rev. B 124(6), 1866–1878 (1961). [CrossRef]
  2. S. Fan and J. D. Joannopoulos, “Analysis of guided resonances in photonic crystal slabs,” Phys. Rev. B 65(23), 235112 (2002). [CrossRef]
  3. R. Magnusson and M. Shokooh-Saremi, “Physical basis for wideband resonant reflectors,” Opt. Express 16(5), 3456–3462 (2008). [CrossRef] [PubMed]
  4. S. T. Thurman and G. M. Morris, “Controlling the spectral response in guided-mode resonance filter design,” Appl. Opt. 42(16), 3225–3233 (2003). [CrossRef] [PubMed]
  5. C. F. R. Mateus, M. C. Y. Huang, L. Chen, C. J. Chang-Hasnain, and Y. Suzuki, “Broadband mirror (1.12-1.62μm) using single-layer sub-wavelength grating,” IEEE Photon. Technol. Lett. 16(7), 1676–1678 (2004). [CrossRef]
  6. T. Sang, L. Wang, S. Ji, Y. Ji, H. Chen, and Z. Wang, “Systematic study of the mirror effect in a poly-Si subwavelength periodic membrane,” J. Opt. Soc. Am. A 26(3), 559–565 (2009). [CrossRef]
  7. Y. Zhou, M. C. Y. Huang, C. Chase, V. Karagodsky, M. Moewe, B. Pesala, F. G. Sedgwick, and C. J. Chang-Hasnain, “High-index-contrast grating (HCG) and its applications in optoelectronic devices,” IEEE J. Sel. Top. Quantum Electron. 15(5), 1485–1499 (2009). [CrossRef]
  8. M. Shokooh-Saremi and R. Magnusson, “Leaky-mode resonant reflectors with extreme bandwidths,” Opt. Lett. 35(8), 1121–1123 (2010). [CrossRef] [PubMed]
  9. M. C. Y. Huang, Y. Zhou, and C. J. Chang-Hasnain, “A surface-emitting laser incorporating a high indexcontrast subwavelength grating,” Nat. Photonics 1(2), 119–122 (2007). [CrossRef]
  10. S. Boutami, B. Ben Bakir, P. Regreny, J. L. Leclercq, and P. Viktorovitch, “Compact 1.55 µm room-temperature optically pumped VCSEL using photonic crystal mirror,” Electron. Lett. 43(5), 282–283 (2007). [CrossRef]
  11. R. Magnusson, M. Shokooh-Saremi, and E. G. Johnson, “Guided-mode resonant wave plates,” Opt. Lett. 35(14), 2472–2474 (2010). [CrossRef] [PubMed]
  12. D. Fattal, J. Li, Z. Peng, M. Fiorentino, and R. G. Beausoleil, “Flat dielectric grating reflectors with focusing abilities,” Nat. Photonics 4(7), 466–470 (2010). [CrossRef]
  13. V. Lousse, W. Suh, O. Kilic, S. Kim, O. Solgaard, and S. Fan, “Angular and polarization properties of a photonic crystal slab mirror,” Opt. Express 12(8), 1575–1582 (2004). [CrossRef] [PubMed]
  14. H. Wu, W. Mo, J. Hou, D. Gao, R. Hao, H. Jiang, R. Guo, W. Wu, and Z. Zhou, “A high performance polarization independent reflector based on a multilayered configuration grating structure,” J. Opt. 12(4), 045703 (2010). [CrossRef]
  15. D. Zhao, Z. Ma, and W. Zhou, “Design of dielectric photonic crystal reflector Fabry-Perot cavities,” Proc. SPIE 7756, 775610 (2010). [CrossRef]
  16. W. Zhou, Z. Ma, H. Yang, Z. Qiang, G. Qin, H. Pang, L. Chen, W. Yang, S. Chuwongin, and D. Zhao, “Flexible photonic-crystal Fano filters based on transferred semiconductor nanomembranes,” J. Phys. D 42(23), 234007 (2009). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited