« journal navigation
|
Stability of extreme ultraviolet multilayer coatings to low energy proton bombardment |
Optics Express, Vol. 19, Issue 16, pp. 14838-14844 (2011)
http://dx.doi.org/10.1364/OE.19.014838
Acrobat PDF (1011 KB)
Article Navigation
▸ Article Outline
– Abstract
1. Introduction
2. Materials and methods
3. Results and discussion
4. Conclusion
– References and links
– Abstract
1. Introduction
2. Materials and methods
3. Results and discussion
4. Conclusion
– References and links
Article Tools
Full Text
Article Info
References
Cited By
Figures
Metrics
Download PDF
Viewing Equations in the
HTML Article
Optimal Viewing Recommendations
Abstract
In this work we present results of an new experiment related to low energy protons bombardments on nano-structured optical coatings. Multilayer structures protected by different capping layers have been fabricated and exposed to low energy protons (1keV). The experimental parameters have been selected considering the potential application of the coatings to solar mission instrumentation. Future solar missions will investigate the Sun from very close distances and optical components are constantly exposed to low energy ion particles irradiation. The experiment was repeated fixing the proton flux while varying the total dose accumulated. Results show that physical processes occurred at the uppermost interfaces can strongly damage the structure.
© 2011 OSA
1. Introduction
Solar Orbiter (SOLO) is a Sun-observing satellite under development by European Space Agency (ESA) whose launch is eventually foreseen in January 2017. It will operate at the closest distance to the Sun ever reached, providing observations characterized by unprecedented resolution. Reaching a minimum perihelion distance of only 0.28 AU, the spacecraft will be immersed in a very harsh environment, which effect on spacecraft and on-board instrumentations must be critically evaluated. One of the main concerns regards possible degradation of optical components induced by the constant bombardment of solar wind ion particles. In this work we present the first experiment carried on in laboratory to establish the effect of solar wind low energy proton bombardment in nanostructured optical coatings. Even though the coatings used in the experiment are specifically optimized for the Multi Element Telescope for Imaging and Spectroscopy (METIS) [1, 2], the experimental approach and results can be of interest not only for other instruments which adopt the same type of coatings, as the Extreme Ultraviolet Imager (EUI) [3], but also for any type of coatings, filters, or optical components experiencing similar environment.
G. Naletto, E. Antonucci, V. Andretta, E. Battistelli, S. Cesare, V. Da Deppo, F. d’Angelo, S. Fineschi, M. Focardi, P. Lamy, F. Landini, D. Moses, G. Nicolini, P. Nicolosi, M. Pancrazzi, M. G. Pelizzo, L. Poletto, M. Romoli, S. Solanki, D. Spadaro, L. Teriaca, M. Uslenghi, and L. Zangrilli, “METIS; the multielement telescope for imaging and spectroscopy for the solar orbiter mission” ICSO Proc. - International Conference on Space Optics, Rhodes (Greece) Oct. 4th-8th (2010).
M. G. Pelizzo, D. Gardiol, P. Nicolosi, A. Patelli, and V. Rigato, “Design, deposition, and characterization of multilayer coatings for the ultraviolet and visible-light coronagraphic imager,” Appl. Opt. 43(13), 2661–2669 (2004). [CrossRef] [PubMed]
The quiet solar wind plasma is mainly composed of protons and other ion species such as α particles (He2 + ), O6 + and Fe10 + , with velocities typically included in the range 300-1200km/s, and with an average value around 468 km/s [4]. More severe occasional disturbances in the solar wind are represented by coronal mass ejections or solar flares, in which high energetic particles are thrown in the heliosphere; even though energies of such particles are higher (in the MeV range) than those of the quiet solar wind (in the keV range), the effect on the instrument components is considered less severe [5].
A. D. Rousseau, D. L. Windt, B. Winter, L. Harra, H. Lamoureux, and F. Eriksson, “Stability of EUV multilayers to long-term heating, and to energetic protons and neutrons, for extreme solar missions,” Proc. SPIE 5900, 590004 , 590004-9 (2005). [CrossRef]
Periodic Mo/Si multilayer working in quasi normal incidence (i.e., 5°) and tuned at HeII Lyman-α line were designed using IMD software: the multilayer stack has 35 bi-layers with period of 16.84 nm and a thickness layer ratio Γ of 0.82. The structure includes also a thin Si capping-layer (which is expected to oxidize upon exposure to air). The same multilayer structure has been designed also with the addition of three different capping-layers, the firsts based on an Ir/Mo and Ir/Si couples and the second on a Ru/Mo one. The capping layer structures were optimized through an analysis of the standing wave distribution throughout the film stack, to maximize the peak reflectance at the target wavelength [6, 7]. These coatings offer superior performance with respect to standard Mo/Si multilayers; full analysis of these new structures is presented elsewhere [8], and the results are compared also with the performance of other recently developed structures [9–11]. In this context the capping layer structure investigation is interesting to verify also the protection capabilities of the underlying Mo/Si structure with respect to the protons bombardment. Ion implantation experiment has been performed using the Low Energy Implanter (LEI) facility. Samples have been characterized prior and after exposure; a non-exposed reference sample for each type of the structure was also monitored to avoid presence of misleading results. Experimental details, results and discussion are presented in the present work.
M. G. Pelizzo, M. Suman, G. Monaco, P. Nicolosi, and D. L. Windt, “High performance EUV multilayer structures insensitive to capping layer optical parameters,” Opt. Express 16(19), 15228–15237 (2008). [CrossRef] [PubMed]
M. G. Pelizzo, M. Suman, D. L. Windt, G. Monaco, and P. Nicolosi, “Innovative methods for optimization and characterization of multilayer coatings (Proceedings Paper)”, Proceedings Vol. 7360, EUV and X-Ray Optics: Synergy between Laboratory and Space, René Hudec; Ladislav Pina, Editors, 73600Q (2009).
H. Takenaka, S. Ichimaru, T. Ohchi, and E. M. Gullikson, “Soft-X-ray reflectivity and heat resistance of SiC/Mg multilayer,” J. Electron Spec. and Rel. Phen. 144-147, 1047–1049 (2005). [CrossRef]
P. Zuppella, G. Monaco, A. J. Corso, P. Nicolosi, D. L. Windt, V. Bello, G. Mattei, and M. G. Pelizzo, “Iridium/silicon multilayers for extreme ultraviolet applications in the 20-35 nm wavelength range,” Opt. Lett. 36(7), 1203–1205 (2011). [CrossRef] [PubMed]
2. Materials and methods
The multilayer used in this experiment are based on a standard Mo/Si periodic multilayer (parameters in Tab.1
) on top of which different capping layer materials structures have been deposited.
Tab.1 Mo/Si multilayer parameter
| Mo/Si multilayer tuned at 30.4nm | |
|---|---|
| d | 16.40 nm |
| Г | 0.82 |
| Si | 13.45 nm |
| Mo | 2.95 nm |
| N | 30 |
Tab.2 Capping layers structure parameters
| ML | Capping layer |
|---|---|
| REF | SiO2 (1.0 nm) |
| Si (1.0 nm) | |
| CL1 | Ir (2.0 nm) |
| Mo (2.2 nm) | |
| CL2 | Ir (2.0 nm) |
| Si (13.5 nm) | |
| CL 3 | Ru (2.0 nm) |
| Mo (2.0 nm) | |
| Si (14.0 nm) | |
| Mo (3.0 nm) |
Multilayers were deposited onto a Si (100) substrate by magnetron sputtering, using a system that has been described previously [12]. Reflectivity measurements at 5° incidence angle in the 25–37 nm spectral range were performed after deposition at the Bending Magnet for Emission Absorption and Reflectivity (BEAR) beamline at ELETTRA Synchrotron (Trieste, Italy), using a 0.9 polarized beam. The ion implantation experiment has been performed at Forschungszentrum Dresden-Rossendorf (Germany, ex Helmholtz-Zentrum Dresden-Rossendorf) using the Low Energy Implanter (LEI) facility. Experimental ion implantation parameters of the experiment have been recovered by the information available in literature related the composition and density of the quiet solar wind species, which have been experimentally measured in situ by different instruments at 1 AU [4]; such parameters are reported in Tab.3
. To derive the same parameters at the innermost part of the heliosphere at a generic distance r from the Sun, such experimental values at 1AU are multiplied by the inverse square of r, assuming therefore a model based on a radial law. In Tab.4
the minimum, maximum and average orbits distance from the Sun reached by SOLO are reported together with the correspondent scaling factors, according to the ESA document [4].
J. Dalla Torre, J.-L. Bocquet, Y. Limoge, J.-P. Crocombette, E. Adam, G. Martin, T. Baron, P. Rivallin, and P. Mur, “Study of self-limiting oxidation of silicon nanoclusters by atomistic simulations,” J. Appl. Phys. 92(2), 1084 (2002). [CrossRef]
Tab.3 Solar Wind parameters
| At 1AU (Earth) | Mission average | |
|---|---|---|
| Density (ions/cm-3) | 8,7 | 25 |
| Speed (km/s) | 468 | 468 |
| Nalpha/Nproton | 0,047 | 0,047 |
Tab. 4 Scaling factor for SOLO mission
| Radius [AU] | Scaling factor [r-2] | |
|---|---|---|
| Min perihelion | 0.23 | 12.70 |
| Max aphelion | 1.48 | 0.45 |
| Mission average | 0.59 | 2.87 |
From the proton plasma density at 1 AU (8.7 ions/cm3), the density at mission average distance can be therefore calculated (Tab.3).
Given the assumption on proton plasma density (25 ions/cm3) and solar wind velocity (468 km/s), it is possible to determine the flux at the SOLO average distance as 1.17x109 proton/cm2 per second. From this data, the number of protons impinging a 1 cm2 sample can be derived as 3.03x1015 in a month, 9.1x1015 in three months, 36.4x1015 in a year, and 36.4x1016 total of the mission (ten years). Two low energy proton implantation sessions have been carried out in order to expose the samples with a three months equivalent dose and one year equivalent dose. The experimental details of each implanting session are summarized in Tab.5
. Proton fluxes used during experiments were computed in order to obtain the desired protons total dose in a reasonable period of time (32 hours for each session in our experiment).
Table 5 Ion implantation experiment details.
| Session A (3 months dose) | Session B (one year dose) | |
|---|---|---|
| Duration | 32 h | 32 h |
| Protons energy | 1 keV | 1 keV |
| Protons flux | 0.79·1011cm2sec−1 | 3.1·1011cm−2sec−1 |
| Total dose | 9.1x1015 protons | 36.4x1015 protons |
During the implantation sessions, the vacuum pressure was lower than 10−8 mbar. The samples were accommodated in a conductive support placed perpendicularly to the proton direction for ensuring a normal incidence implantation (Fig. 1
). The proton current was measured and integrated over time in order to control the total dose. After implantation, the samples were measured again at BEAR beamline.
3. Results and discussion
The reflectances of the structures before and after implantation are reported in Fig. 2
. A non-irradiated witness sample has also been re-measured to verify possible degradation due to natural aging of the structures.
Fig. 2 Reflectance measurements of the structures REF (a), CL1 (b), CL2 (c) and CL3 (d) before and after low energy protons implantation experiment.
The reflectance peaks prior proton bombardment of the structures overcoated by a capping-layer are higher than standard Si/Mo, being such values ~0.27 for the Ir/Mo, ~0.25 for the Ru/Mo and only ~0.21 for the Si/Mo (Tab.6
). The same spectral bandpass of 2.9 nm FWHM has been found in all samples. All coatings have been verified being stable after six months. After proton the bombardment, measurements have been repeated, mapping the surface in different places. After implantation session B, the Ir/* capped multilayers dropped slightly. In contrast, the Ru/Mo capped film showed a reflectance loss after session A, with even more dramatic losses in reflectance after session B. While after session B also Mo/Si standard multilayer show a degradation, they shows an initial increase of reflectance after session A. This behavior has been verified on two identical Si/Mo samples, which were deposited by sputtering in two different deposition runs; further investigation had been necessary to understand such physical phenomena. Therefore X-ray Photoemission Spectroscopy (XPS) has been carried out for all samples at ELETTRA-BEAR beamline. XPS survey photons (energy 800eV, pass energy 20eV, binding energy step 0.152eV) on Ir/Mo capped multilayer before and after implantation (session B) is shown in Fig. 3
: the data show an increase of the carbon emission after session B, which should be attributed to a deposition of a carbon layer on the top of the structure due to contamination during implantation.
Tab.6 Peak reflectance of the multilayer structure before and proton implantation experiment.
An estimation of the carbon layer thickness of ~2nm has been determined from a fit of the Si/Mo reflectance measurements. This overcoating causes an increase in the interference effect of the last two layers. This same layer does not have any effect if deposited on top of a heavy metal capping layer, as in case of ruthenium and iridium. This overcoat cannot explain the wavelength shift observed in all samples, neither the dramatic loss of reflectivity of the Ru/Mo capped multilayer. The roughness of the film surfaces has been verified by AFM before and after implantation; no increase in roughness was found in any of the samples. TEM analysis was carried out on the most damaged sample, which is Ru/Mo capped multilayer after session B. Bright-Field cross-sectional images of the multilayer prior and after bombardment are shown in Fig. 4
. The apparent mechanism of ML damage is the formation of a vacancy layer beneath the second Si layer from surface. Clearly, the first top layers of the structure are peeled off from the underneath structures, and this determined a definitive degradation of the multilayer.
4. Conclusion
For the first time multilayer coatings for high EUV reflectance have been irradiated by low energy (1 keV) protons to verify their stability over time in Sun close heliosphere. Optical characterization of the sample prior and after the experiment shows that proton bombardment can strongly damage the nanostructures. All samples show a change in reflectivity (peak and wavelength shift), which has been demonstrated to be more dramatic in case of a Ru/Mo capping layer, and lesser sever in case of an Ir/Mo or Ir/Si capping layer. The physical processes happening on top surface has been investigated by TEM analysis, which shows that the damage consists in the formation of a vacancy layer underneath the first top layers. From the work completed thus far, we can conclude that Ir/Mo and Ir/Si capped multilayer provides the highest efficiency at 30.4 nm and a better stability to proton bombardment, and therefore are up to now considered as best candidate for SOLO-METIS instrument. Nevertheless, other tests are needed to fully validate these coatings, in particular using other ion species as alpha-particles.
Acknowledgments.
The authors thank Dr. A. Giglia for measurement at ELETTRA-BEAR beamline, Dr. D. Henke and the SPIRIT technical and administrative staff of the Forschungszentrum Dresden-Rossendorf for support during ion implantation experiment, Dr. E. Antonucci and S. Fineschi, INAF-OATO, and all the METIS team. The author are grateful to U. Schuele, Max Planck Institute for Solar System Research, for helpful discussions. This work has been performed with the financial support of the Italian Space Agency (ASI/INAF/015/07/0 and ASI/INAF/Solar Orbiter) and of the Cassa di Risparmio di Padova e Rovigo (CARIPARO) Foundation-Bandi di Eccellenza 2009/2010. This work has been supported by the European Community as an Integrating Activity “Support of Public and Industrial Research Using Ion Beam Technology (SPIRIT)” under EC contract no. 227012.
References and links
G. Naletto, E. Antonucci, V. Andretta, E. Battistelli, S. Cesare, V. Da Deppo, F. d’Angelo, S. Fineschi, M. Focardi, P. Lamy, F. Landini, D. Moses, G. Nicolini, P. Nicolosi, M. Pancrazzi, M. G. Pelizzo, L. Poletto, M. Romoli, S. Solanki, D. Spadaro, L. Teriaca, M. Uslenghi, and L. Zangrilli, “METIS; the multielement telescope for imaging and spectroscopy for the solar orbiter mission” ICSO Proc. - International Conference on Space Optics, Rhodes (Greece) Oct. 4th-8th (2010). | |
M. G. Pelizzo, D. Gardiol, P. Nicolosi, A. Patelli, and V. Rigato, “Design, deposition, and characterization of multilayer coatings for the ultraviolet and visible-light coronagraphic imager,” Appl. Opt. 43(13), 2661–2669 (2004). [CrossRef] [PubMed] | |
J. P. Halain, Y. Houbrechts, F. Auchère, P. Rochus, T. Appourchaux, D. Berghmans, U. Schühle, L. Harra, E. Renotte, and A. Zukhov, The SOLar Orbiter EUI instrument optical developments, ICSO Proc. - International Conference on Space Optics, Rhodes (Greece) Oct. 4th-8th (2010). | |
ESA, “Solar Orbiter environmental specification”, Issue 2.0 (2008). | |
A. D. Rousseau, D. L. Windt, B. Winter, L. Harra, H. Lamoureux, and F. Eriksson, “Stability of EUV multilayers to long-term heating, and to energetic protons and neutrons, for extreme solar missions,” Proc. SPIE 5900, 590004 , 590004-9 (2005). [CrossRef] | |
M. G. Pelizzo, M. Suman, G. Monaco, P. Nicolosi, and D. L. Windt, “High performance EUV multilayer structures insensitive to capping layer optical parameters,” Opt. Express 16(19), 15228–15237 (2008). [CrossRef] [PubMed] | |
M. G. Pelizzo, M. Suman, D. L. Windt, G. Monaco, and P. Nicolosi, “Innovative methods for optimization and characterization of multilayer coatings (Proceedings Paper)”, Proceedings Vol. 7360, EUV and X-Ray Optics: Synergy between Laboratory and Space, René Hudec; Ladislav Pina, Editors, 73600Q (2009). | |
A. J. Corso, P. Zuppella, P. Nicolosi, D. L. Windt, E. Gullikson, and M. G. Pelizzo, “Capped multilayers with improved performances at 30.4 nm for future solar missions”, Accepted by Opt. Express (2011). | |
H. Takenaka, S. Ichimaru, T. Ohchi, and E. M. Gullikson, “Soft-X-ray reflectivity and heat resistance of SiC/Mg multilayer,” J. Electron Spec. and Rel. Phen. 144-147, 1047–1049 (2005). [CrossRef] | |
M. H. Hu, K. Le Guen, J. M. André, P. Jonnard, E. Meltchakov, F. Delmotte, and A. Galtayries, “Structural properties of Al/Mo/SiC multilayers with high reflectivity for extreme ultraviolet light,” Opt. Express 18(19), 20019–20028 (2010). [CrossRef] [PubMed] | |
P. Zuppella, G. Monaco, A. J. Corso, P. Nicolosi, D. L. Windt, V. Bello, G. Mattei, and M. G. Pelizzo, “Iridium/silicon multilayers for extreme ultraviolet applications in the 20-35 nm wavelength range,” Opt. Lett. 36(7), 1203–1205 (2011). [CrossRef] [PubMed] | |
J. Dalla Torre, J.-L. Bocquet, Y. Limoge, J.-P. Crocombette, E. Adam, G. Martin, T. Baron, P. Rivallin, and P. Mur, “Study of self-limiting oxidation of silicon nanoclusters by atomistic simulations,” J. Appl. Phys. 92(2), 1084 (2002). [CrossRef] |
OCIS Codes
(230.4170) Optical devices : Multilayers
(260.7200) Physical optics : Ultraviolet, extreme
(350.1820) Other areas of optics : Damage
(350.4990) Other areas of optics : Particles
(350.6090) Other areas of optics : Space optics
ToC Category:
Thin Films
History
Original Manuscript: May 10, 2011
Revised Manuscript: July 1, 2011
Manuscript Accepted: July 1, 2011
Published: July 18, 2011
Citation
M.G. Pelizzo, Alain Jody Corso, Paola Zuppella, D.L. Windt, G. Mattei, and P. Nicolosi, "Stability of extreme ultraviolet multilayer coatings to low energy proton bombardment," Opt. Express 19, 14838-14844 (2011)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-19-16-14838
Sort: Year | Journal | Reset
References
- G. Naletto, E. Antonucci, V. Andretta, E. Battistelli, S. Cesare, V. Da Deppo, F. d’Angelo, S. Fineschi, M. Focardi, P. Lamy, F. Landini, D. Moses, G. Nicolini, P. Nicolosi, M. Pancrazzi, M. G. Pelizzo, L. Poletto, M. Romoli, S. Solanki, D. Spadaro, L. Teriaca, M. Uslenghi, and L. Zangrilli, “METIS; the multielement telescope for imaging and spectroscopy for the solar orbiter mission” ICSO Proc. - International Conference on Space Optics, Rhodes (Greece) Oct. 4th-8th (2010).
- M. G. Pelizzo, D. Gardiol, P. Nicolosi, A. Patelli, and V. Rigato, “Design, deposition, and characterization of multilayer coatings for the ultraviolet and visible-light coronagraphic imager,” Appl. Opt. 43(13), 2661–2669 (2004). [CrossRef] [PubMed]
- J. P. Halain, Y. Houbrechts, F. Auchère, P. Rochus, T. Appourchaux, D. Berghmans, U. Schühle, L. Harra, E. Renotte, and A. Zukhov, The SOLar Orbiter EUI instrument optical developments, ICSO Proc. - International Conference on Space Optics, Rhodes (Greece) Oct. 4th-8th (2010).
- ESA, “Solar Orbiter environmental specification”, Issue 2.0 (2008).
- A. D. Rousseau, D. L. Windt, B. Winter, L. Harra, H. Lamoureux, and F. Eriksson, “Stability of EUV multilayers to long-term heating, and to energetic protons and neutrons, for extreme solar missions,” Proc. SPIE 5900, 590004, 590004-9 (2005). [CrossRef]
- M. G. Pelizzo, M. Suman, G. Monaco, P. Nicolosi, and D. L. Windt, “High performance EUV multilayer structures insensitive to capping layer optical parameters,” Opt. Express 16(19), 15228–15237 (2008). [CrossRef] [PubMed]
- M. G. Pelizzo, M. Suman, D. L. Windt, G. Monaco, and P. Nicolosi, “Innovative methods for optimization and characterization of multilayer coatings (Proceedings Paper)”, Proceedings Vol. 7360, EUV and X-Ray Optics: Synergy between Laboratory and Space, René Hudec; Ladislav Pina, Editors, 73600Q (2009).
- A. J. Corso, P. Zuppella, P. Nicolosi, D. L. Windt, E. Gullikson, and M. G. Pelizzo, “Capped multilayers with improved performances at 30.4 nm for future solar missions”, Accepted by Opt. Express (2011).
- H. Takenaka, S. Ichimaru, T. Ohchi, and E. M. Gullikson, “Soft-X-ray reflectivity and heat resistance of SiC/Mg multilayer,” J. Electron Spec. and Rel. Phen. 144-147, 1047–1049 (2005). [CrossRef]
- M. H. Hu, K. Le Guen, J. M. André, P. Jonnard, E. Meltchakov, F. Delmotte, and A. Galtayries, “Structural properties of Al/Mo/SiC multilayers with high reflectivity for extreme ultraviolet light,” Opt. Express 18(19), 20019–20028 (2010). [CrossRef] [PubMed]
- P. Zuppella, G. Monaco, A. J. Corso, P. Nicolosi, D. L. Windt, V. Bello, G. Mattei, and M. G. Pelizzo, “Iridium/silicon multilayers for extreme ultraviolet applications in the 20-35 nm wavelength range,” Opt. Lett. 36(7), 1203–1205 (2011). [CrossRef] [PubMed]
- J. Dalla Torre, J.-L. Bocquet, Y. Limoge, J.-P. Crocombette, E. Adam, G. Martin, T. Baron, P. Rivallin, and P. Mur, “Study of self-limiting oxidation of silicon nanoclusters by atomistic simulations,” J. Appl. Phys. 92(2), 1084 (2002). [CrossRef]
Cited By |
 Alert me when this paper is cited |
OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.
« Previous Article | Next Article »
OSA is a member of 