Stable low-loss optical nanofibres embedded in hydrophobic aerogel

doi:10.1364/OE.19.000764

« Show journal navigation

Stable low-loss optical nanofibres embedded in hydrophobic aerogel

Limin Xiao, M. D. W. Grogan, W. J. Wadsworth, R. England, and T. A. Birks »View Author Affiliations

Optics Express, Vol. 19, Issue 2, pp. 764-769 (2011)
http://dx.doi.org/10.1364/OE.19.000764

View Full Text Article

Acrobat PDF (917 KB)

Journal Search
Article Lookup

Article Tools

Citations

Alert me when this article is cited
Export Citation/Save

Article Navigation

▸ Article Outline
– Abstract
1. Introduction
2. Method and applications
3. Conclusion
– References and links

Article Tools
Full Text
Article Info
References
Cited By
Figures
Metrics
Download PDF

Viewing Equations in the
HTML Article

Optimal Viewing Recommendations

Full Text
Article Info
References (28)
Cited By
Figures (5)
Metrics

Abstract

Nanofibres, optical fibres narrower than the wavelength of light, degrade in hours on exposure to air. We show that encapsulation in hydrophobic silica aerogel (refractive index 1.05) provides protection and stability (over 2 months) without sacrificing low attenuation, strong confinement and accessible evanescent field. The measured attenuation was <0.03 dB/mm, over 10 × lower than reported with other encapsulants. This enables many nanofibre applications based on their extreme small size and strong external evanescent field, such as optical sensors, nonlinear optics, nanofibre circuits and high-Q resonators. The aerogel is more than a waterproof box, it is a completely-compatible gas-permeable material in intimate contact with the nanofibre and hydrophobic on both the macroscopic and molecular scales. Its benefits are illustrated by experiments on gas sensing (exploiting the aerogel's porosity) and supercontinuum generation (exploiting its ultra-low index).

1. Introduction

Optical nanofibres confine light to a small core, with strong evanescent fields and high optical nonlinearity [1

H. S. MacKenzie and F. P. Payne, “Evanescent field amplification in a tapered single-mode optical fibre,” Electron. Lett. 26(2), 130–132 (1990). [CrossRef]

–5

S. G. Leon-Saval, T. A. Birks, W. J. Wadsworth, P. St. J. Russell, and M. W. Mason, “Supercontinuum generation in submicron fibre waveguides,” Opt. Express 12(13), 2864–2869 (2004). [CrossRef] [PubMed]

]. Their advantages over other optical nanowires (such as silicon-on-insulator or chalcogenide strip waveguides) include built-in transitions to single-mode fibres with low coupling loss, extremely low optical loss (down to ~0.001 dB/mm) [4

G. Brambilla, F. Xu, P. Horak, Y. Jung, F. Koizumi, N. P. Sessions, E. Koukharenko, X. Feng, G. S. Murugan, J. S. Wilkinson, and D. J. Richardson, “Optical fiber nanowires and microwires: fabrication and applications,” Adv. Opt. Photon. 1(1), 107–161 (2009). [CrossRef]

], high mechanical strength [6

G. Brambilla and D. N. Payne, “The ultimate strength of glass silica nanowires,” Nano Lett. 9(2), 831–835 (2009). [CrossRef] [PubMed]

] and simplicity of fabrication [3

L. M. Tong, R. R. Gattass, J. B. Ashcom, S. L. He, J. Y. Lou, M. Y. Shen, I. Maxwell, and E. Mazur, “Subwavelength-diameter silica wires for low-loss optical wave guiding,” Nature 426(6968), 816–819 (2003). [CrossRef] [PubMed]

–6

G. Brambilla and D. N. Payne, “The ultimate strength of glass silica nanowires,” Nano Lett. 9(2), 831–835 (2009). [CrossRef] [PubMed]

]. A wide range of applications have been explored such as optical sensors [7

P. Polynkin, A. Polynkin, N. Peyghambarian, and M. Mansuripur, “Evanescent field-based optical fiber sensing device for measuring the refractive index of liquids in microfluidic channels,” Opt. Lett. 30(11), 1273–1275 (2005). [CrossRef] [PubMed]

J. Villatoro and D. Monzón-Hernández, “Fast detection of hydrogen with nano fiber tapers coated with ultra thin palladium layers,” Opt. Express 13(13), 5087–5092 (2005). [CrossRef] [PubMed]

], nanofibre circuits [3

L. M. Tong, J. Y. Lou, R. R. Gattass, S. L. He, X. W. Chen, L. Liu, and E. Mazur, “Assembly of silica nanowires on silica aerogels for microphotonic devices,” Nano Lett. 5(2), 259–262 (2005). [CrossRef] [PubMed]

,10

Y. Li and L. M. Tong, “Mach-Zehnder interferometers assembled with optical microfibers or nanofibers,” Opt. Lett. 33(4), 303–305 (2008). [CrossRef] [PubMed]

], nonlinear optics including supercontiuum generation [5

,11

D. I. Yeom, E. C. Mägi, M. R. E. Lamont, M. A. F. Roelens, L. Fu, and B. J. Eggleton, “Low-threshold supercontinuum generation in highly nonlinear chalcogenide nanowires,” Opt. Lett. 33(7), 660–662 (2008). [CrossRef] [PubMed]

] and high-Q resonators [4

,12

M. Sumetsky, “Basic Elements for Microfiber Photonics: Micro/Nanofibers and Microfiber Coil Resonators,” J. Lightwave Technol. 26(1), 21–27 (2008). [CrossRef]

,13

G. Vienne, Y. Li, and L. M. Tong, “Effect of Host Polymer on Microfiber Resonator,” IEEE Photon. Technol. Lett. 19(18), 1386–1388 (2007). [CrossRef]

]. Unfortunately, their optical performance quickly degrades after fabrication due to surface light scattering from dust particles and from cracks induced by water vapour, resulting in large irrecoverable increases in loss and eventual mechanical failure [6

G. Brambilla and D. N. Payne, “The ultimate strength of glass silica nanowires,” Nano Lett. 9(2), 831–835 (2009). [CrossRef] [PubMed]

,13

G. Vienne, Y. Li, and L. M. Tong, “Effect of Host Polymer on Microfiber Resonator,” IEEE Photon. Technol. Lett. 19(18), 1386–1388 (2007). [CrossRef]

–16

N. Lou, R. Jha, J. L. Domínguez-Juárez, V. Finazzi, J. Villatoro, G. Badenes, and V. Pruneri, “Embedded optical micro/nano-fibers for stable devices,” Opt. Lett. 35(4), 571–573 (2010). [CrossRef] [PubMed]

]. The high surface-to-volume ratio and strong evanescent field of nanofibres make them particularly prone to this problem [4

,14

G. Brambilla, F. Xu, and X. Feng, “Fabrication of optical fibre nanowires and their optical and mechanical characterization,” Electron. Lett. 42(9), 517–519 (2006). [CrossRef]

]. Couplers and resonators based on loops, coils or knots are also susceptible to mechanical disturbance because they are held in place only by weak natural adhesive forces.

Suspension in a hermetically-sealed package (as used to house fused fibre couplers) excludes dust and moisture but is not enough to stabilise looped devices and precludes sensing applications. Better support can be achieved on a low-index substrate such as MgF₂ [10

Y. Li and L. M. Tong, “Mach-Zehnder interferometers assembled with optical microfibers or nanofibers,” Opt. Lett. 33(4), 303–305 (2008). [CrossRef] [PubMed]

] or silica aerogel [9

], or between two such substrates [4

], but these do not eliminate movement or ingress of moisture. Encapsulation in polymers such as Teflon (PTFE) [7

,13

G. Vienne, Y. Li, and L. M. Tong, “Effect of Host Polymer on Microfiber Resonator,” IEEE Photon. Technol. Lett. 19(18), 1386–1388 (2007). [CrossRef]

–16

] protects and stabilises nanofibres but at the expense of greatly increased attenuation (~2 dB/mm for 900 nm diameter [15

F. Xu and G. Brambilla, “Preservation of micro-optical fibers by embedding,” Jpn. J. Appl. Phys. 47(8), 6675–6677 (2008). [CrossRef]

] and 0.4 dB/mm for 1000 nm diameter [16

] nanofibres at 1550 nm wavelength). Because the medium surrounding the nanofibre is an integral part of the waveguide, the high refractive index of the encapsulant (e.g. Teflon, n = 1.31) relative to air weakens light confinement, completely changes chromatic dispersion (and hence nonlinear properties), enhances the spread of the evanescent field and modifies the splitting properties of directional couplers, making it difficult to realise compact devices [7

,13

G. Vienne, Y. Li, and L. M. Tong, “Effect of Host Polymer on Microfiber Resonator,” IEEE Photon. Technol. Lett. 19(18), 1386–1388 (2007). [CrossRef]

,15

F. Xu and G. Brambilla, “Preservation of micro-optical fibers by embedding,” Jpn. J. Appl. Phys. 47(8), 6675–6677 (2008). [CrossRef]

]. Encapsulation also prevents evanescent sensing, unless the encapsulant is thinned to allow the evanescent field to reach the external medium [7

,16

We overcome these drawbacks by embedding nanofibres in transparent hydrophobic silica aerogel formed in situ around the fibre using sol-gel chemistry [17

G. M. Pajonk, “Transparent silica aerogels,” J. Non-Cryst. Solids 225(1), 307–314 (1998). [CrossRef]

,18

L. M. Xiao, M. D. W. Grogan, S. G. Leon-Saval, R. Williams, R. England, W. J. Wadsworth, and T. A. Birks, “Tapered fibers embedded in silica aerogel,” Opt. Lett. 34(18), 2724–2726 (2009). [CrossRef] [PubMed]

]. Silica aerogel is nanoporous silica glass structured on a scale much smaller than optical wavelengths [17

G. M. Pajonk, “Transparent silica aerogels,” J. Non-Cryst. Solids 225(1), 307–314 (1998). [CrossRef]

]. It has a low refractive index (typically 1.01 - 1.05), behaves optically like “solid air”, and so has little effect on the optical properties of nanofibre devices when replacing air around them. In particular, the optical attenuation due to encapsulation is much smaller with aerogel than with polymers. Aerogel is also thermally compatible with nanofibres, unlike polymers, because both are made from silica glass. Completely encapsulating a nanofibre in hydrophobic aerogel (rather than laying the nanofibre on the aerogel [9

]) mechanically stabilises and protects the nanofibre from degradation, while the aerogel's porous structure allows the evanescent sensing of gases without exposing the bare nanofibre.

2. Method and applications

We have previously demonstrated the encapsulation of tapered fibres with diameters ≥1 µm in silica aerogel, and the induced loss was ~0.11 dB/mm [18

]. However aerogel made by supercritical CO₂ drying is hydrophilic because its large-area internal surface is covered with hydroxyl groups as shown in Fig. 1(a) [19

H. Yokogawa and M. Yokoyama, “Hydrophobic silica aerogels,” J. Non-Cryst. Solids 186, 23–29 (1995). [CrossRef]

]. It can therefore condense water vapour from the air which can cause shrinkage under capillary forces. Indeed a drop of water quickly destroys the transparent aerogel where it lands, turning it to opaque white powder, Fig. 1(c). Hence the aerogel is not stable and we had to store our previous samples [18

] in desiccant boxes. It was not then possible to similarly encapsulate submicron tapered fibres because the aerogel shrunk by ~4% during formation, which broke thinner fibres.

Fig. 1 Schematic internal surface structures of (a) hydrophilic aerogel with hydroxyl groups and (b) hydrophobic aerogel with trimethylsilyl groups. The horizontal lines distinguish the surface groups above from the bulk glass below. (c) Hydrophilic aerogel is turned to white powder by a 2.6 mm diameter drop of water. (d) A similar water drop sits without reacting on the surface of hydrophobic aerogel with a contact angle of ~160°.

In this work, to make the aerogel hydrophobic and avoid these problems we started with the same procedure as before, tapering low-loss (<0.1 dB) nanofibres and immersing them in a sol made from tetramethyl orthosilicate, methanol and water with ammonia as a catalyst [18

]. After a few minutes the fluid sol around the nanofibre turns to rigid wet gel, which is aged for at least two days to allow the reaction to complete, then soaked in methanol for another two days to diffusively remove excess water. We then soaked the wet gel in 20 wt-% hexamethyldisilazane (HMDS) solution in methanol for a day to replace most surface hydroxyl groups with trimethylsilyl (-OSi(CH₃)₃) [17

G. M. Pajonk, “Transparent silica aerogels,” J. Non-Cryst. Solids 225(1), 307–314 (1998). [CrossRef]

,19

H. Yokogawa and M. Yokoyama, “Hydrophobic silica aerogels,” J. Non-Cryst. Solids 186, 23–29 (1995). [CrossRef]

], as shown in Fig. 1(b). Importantly, we expect hydroxyl on the surface of the nanofibre to also be replaced, making the nanofibre itself hydrophobic too. Then the wet gel was soaked again in pure methanol to diffusively remove excess HMDS. The alcogel was immersed in liquid CO₂ (85 bar, ~20 °C) for 3.5 hours to diffusively replace the methanol within the gel, then the CO₂ was raised to supercritical conditions (100 bar, ~40 °C) for 2.5 hours, followed by depresssurisation over ~3 hours. This supercritically dries the wet gel to produce a block of hydrophobic aerogel with the nanofibre embedded in it. The aerogel made this way shrunk less than 1% in linear dimensions during formation and so did not damage the embedded nanofibre. This is a key beneficial side effect of the hydrophobic process. It was stable over time and waterproof, supporting a drop of water (without degradation) with a contact angle of 140 - 160°, Fig. 1(d). The aerogel was substantially transparent. Similar aerogel (without embedded fibres) had an attenuation of 0.02 dB/mm for 1550 nm light, and its refractive index was 1.05 as determined by measuring the critical angle for an internally-reflected laser beam. Samples have also been left floating in water for several months without apparent degradation.

Figure 2(a) shows a nanofibre waist 20 mm long and 0.8 µm in diameter embedded in hydrophobic aerogel. Figure 2(b) and 2(c) are scanning electron micrographs (SEMs) of tapered fibres emerging from aerogel blocks, showing the intimate contact between fibre and aerogel. Figure 2(d) is a spectrum of the loss due to encapsulation for the fibre of Fig. 2(a). A reference transmission spectrum was measured through a length of fibre connected between a stable multiple-LED light source and an optical spectrum analyser. The fibre was then broken in the middle without disturbing the connections to the instruments, and the encapsulated sample was spliced into the fibre with a fusion splicer. A device transmission spectrum was then measured and divided by the reference measurement to yield a normalised loss spectrum. The measurement therefore includes the initial loss of the tapered fibre and of the two splice joints, and so is an upper bound for the loss due to encapsulation. (The total loss of the two splice joints was less than 0.1 dB.) The encapsulation loss divided by the length of the tapered waist was less than 0.03 dB/mm except around the OH peak at ~1380 nm, over an order of magnitude less than the lowest previously-reported attenuation for a Teflon encapsulated nanofibre [16

] despite the smaller diameter.

Fig. 2 (a) A nanofibre 20 mm long and 800 nm in diameter embedded in hydrophobic aerogel. The fibre carries red laser light from left to right, to reveal the nanofibre waist by the weak scattering of the evanescent field by the aerogel. Scanning electron micrographs (SEMs) of nanofibres with diameters of (b) 28 µm and (c) 700 nm emerging from aerogel blocks that were broken to show the intimate contact between fibre and aerogel. Inset: SEM of an aerogel surface (500 nm scale bar) with pore structure small compared to optical wavelengths. (d) The loss spectrum of the nanofibre immediately after encapsulation. Inset: detail between 1510 and 1545 nm immediately after encapsulation and 15 days later.

We attribute the lower attenuation mainly to stronger mode confinement by the low air-like refractive index of the aerogel (n = 1.05), as well as to its transparency. The fraction of fundamental mode power in the evanescent field is plotted in Fig. 3(a) against external index n. Light confinement in a 800 nm diameter nanofibre is similar with aerogel (n = 1.05) and air (n = 1.00) outside the nanofibre, but much weaker with Teflon (n = 1.31) and weaker still with higher-index polymers, Fig. 3(b). Much less light therefore propagates in the lossier external medium and at the scattering fibre boundary. Another benefit is that the taper transition length needed for adiabatic propagation is much shorter [20

M. Sumetsky, “How thin can a microfiber be and still guide light?” Opt. Lett. 31(7), 870–872 (2006). [CrossRef] [PubMed]

Fig. 3 (a) Calculated fraction of power in the fundamental mode's evanescent field at 1550 nm wavelength versus external index, for the nanofibre diameters marked. (b) Corresponding intensity distributions (normalised to a common peak value) along an axis perpendicular to the direction of the electrical field, for an 800 nm diameter nanofibre in air, aerogel and Teflon. The dotted lines mark the boundary of the nanofibre.

The attenuation of the 800 nm encapsulated nanofibre was stable over time, changing by less than the ± 0.1 dB experimental error after 15 days' exposure to air in a lab without air conditioning or filtration, Fig. 2(d) inset. The attenuation of a narrower (700 nm diameter) encapsulated nanofibre did not change after two months. It is notable that the aerogel protects the nanofibre despite its open network of pores tens of nm wide. Though these are narrow enough to filter dust particles, water vapour can still diffuse into the aerogel and approach the nanofibre surface. However, any trimethylsilyl groups covering the nanofibre (from the process that made the aerogel hydrophobic) protect it from water adsorption and condensation, inhibiting the formation of the surface cracks thought to cause loss (and indeed mechanical weakness) [14

G. Brambilla, F. Xu, and X. Feng, “Fabrication of optical fibre nanowires and their optical and mechanical characterization,” Electron. Lett. 42(9), 517–519 (2006). [CrossRef]

–16

Uniquely among proposed encapsulants, porous aerogel allows an embedded nanofibre to act as an evanescent-field gas sensor. Oxygen was reported to diffuse through aerogel at a rate only an order of magnitude slower than unimpeded diffusion in air, with a diffusion coefficient of 1-2 mm²/s [21

N. Leventis, I. A. Elder, D. R. Rolison, M. L. Anderson, and C. I. Merzbacher, “Durable Modification of Silica Aerogel Monoliths with Fluorescent 2,7-Diazapyrenium Moieties. Sensing Oxygen near the Speed of Open-Air Diffusion,” Chem. Mater. 11(10), 2837–2845 (1999). [CrossRef]

]. Acetylene (C₂H₂) has a conveniently-distinctive absorption spectrum, and should diffuse similarly in our aerogel because the gases' molecular masses and the aerogels' pore sizes are similar. We therefore demonstrated gas sensing by placing the encapsulated nanofibre of Fig. 2(a) in a test chamber into which acetylene gas could be introduced and removed at atmospheric pressure. The familiar absorption signature of acetylene appeared in the transmission spectrum, Fig. 4 , increasing with concentration to a peak of ~2 dB at close to 100% concentration. The change was completely reversible, the induced loss returning to zero when the acetylene was removed. The response time was 16 ± 3 s for diffusion in both directions, consistent with the estimated diffusion time through 5 mm of aerogel [21

]. The sensitivity can be increased by lengthening or narrowing the nanofibre, and the response speed by reducing the width of the aerogel block. The response time compares favourably with that of “holey” photonic crystal fibres, where the long diffusion distance severely increases the response time to over 3 hours for a 1 m fibre [22

Y. L. Hoo, W. Jin, C. Z. Shi, H. L. Ho, D. N. Wang, and S. C. Ruan, “Design and modeling of a photonic crystal fiber gas sensor,” Appl. Opt. 42(18), 3509–3515 (2003). [CrossRef] [PubMed]

]. Micro-channels through the sides of the PCF speed up diffusion but need protection by a permeable material to prevent contamination while allowing gases to pass [22

Y. L. Hoo, W. Jin, C. Z. Shi, H. L. Ho, D. N. Wang, and S. C. Ruan, “Design and modeling of a photonic crystal fiber gas sensor,” Appl. Opt. 42(18), 3509–3515 (2003). [CrossRef] [PubMed]

,23

A. van Brakel, C. Grivas, M. N. Petrovich, and D. J. Richardson, “Micro-channels machined in microstructured optical fibers by femtosecond laser,” Opt. Express 15(14), 8731–8736 (2007). [CrossRef] [PubMed]

]. In contrast, the aerogel allows gases to diffuse directly to the nanofibre while blocking contaminants. Indeed the tendency of water droplets to roll off hydrophobic surfaces like our aerogel, collecting surface contaminants as it goes, is a “self-cleaning” property that could be useful in some applications [24

A. Roig, E. Molins, E. Rodríguez, S. Martínez, M. Moreno-Mañas, and A. Vallribera, “Superhydrophobic silica aerogels by fluorination at the gel stage,” Chem. Commun. (Camb.) 20(20), 2316–2317 (2004). [CrossRef]

Fig. 4 Steady-state transmission spectra of a nanofibre with waist length 20 mm and diameter 800 nm embedded in aerogel, after the surrounding air was replaced by acetylene gas at atmospheric pressure, and after the acetylene was replaced by air again. The spectra are both relative to the transmission before the acetylene was first introduced.

For nonlinear-optical applications of nanofibres [5

,11

], the low air-like refractive index of aerogel is particularly valuable. Replacing air with aerogel has little effect on the nanofibre's group-velocity dispersion spectrum (Fig. 5(a) ) or the effective area of the guided mode (Fig. 3(b)), whereas both are very different in Teflon. Figure 5(a) shows that our nanofibre's zero-dispersion wavelength (a key parameter in nonlinear optics) is 510 nm in air and 530 nm in aerogel, whereas in Teflon the dispersion is always strongly normal and never zero. We could therefore demonstrate visible single-mode supercontinuum generation (Fig. 5(b)) in a 20 mm long nanofibre pumped by a pulsed green laser, as in [5

] but with hydrophobic aerogel to protect the nanofibre and indefinitely extend its lifetime. The output spectrum was unchanged after half an hour, whereas an unencapsulated nanofibre would have been destroyed in this time by laser-induced heating at surface scatter points caused by dust or cracks.

Fig. 5 (a) Calculated dispersion spectra of a silica nanofibre of diameter 800 nm in air, aerogel and Teflon. The material dispersion of silica and Teflon [27

M. K. Yang, R. H. French, and E. W. J. Tokarsky, “Optical properties of Teflon AF amorphous fluoropolymers,” J. Micro/Nanolith. MEMS MOEMS 7(3), 033010 (2008). [CrossRef]

] are included, but that of aerogel was ignored because its index variation with wavelength is small compared to bulk silica [28

T. Bellunato, M. Calvi, C. Matteuzzi, M. Musy, D. L. Perego, and B. Storaci, “Refractive index dispersion law of silica aerogel,” Eur. Phys. J. C 52(3), 759–764 (2007). [CrossRef]

]. (b) The output supercontinuum spectrum from a nanofibre 20 mm long and 800 nm in diameter embedded in aerogel, pumped by ~300 fs pulses of 540 nm wavelength with a repetition rate of 20 MHz. The total output power measured with a thermal power meter was 5.7 mW. Inset is a photograph of the output far field pattern.

Like other glass bodies, aerogel blocks are brittle and can be destroyed by rough treatment. Nevertheless our relatively dense (0.24 g/cm³) aerogel was robust enough to be handled normally without damaging either the aerogel or the nanofibre inside it, with scope for further improvement [25

T. Y. Wei, S. Y. Lu, and Y. C. J. Chang, “Transparent, hydrophobic composite aerogels with high mechanical strength and low high-temperature thermal conductivities,” J. Phys. Chem. B 112(38), 11881–11886 (2008). [CrossRef] [PubMed]

]. Indeed the rigidity of this brittle encapsulant provides optical stability under mechanical or thermal stresses. All that is needed is a ruggedised secondary package to prevent gross crushing. We also expect aerogel-encapsulated devices to be more robust than the alternatives in high-pressure or vacuum environments, especially where the pressure is variable, because the aerogel allows gases around the nanofibre to “breathe” through the encapsulant.

3. Conclusion

In conclusion, encapsulation in hydrophobic aerogel overcomes key impediments to the exploitation of optical nanofibres and nanofibre devices, including degradation over time, encapsulation-induded loss, undesirable changes in light confinement and dispersion, thermal sensitivity, and movements in unsupported structures. The aerogel is a rigid barrier to particulate contaminants, waterproof on macroscopic and molecular scales, potentially self-cleaning, permeable to gases, and optically like air. We have demonstrated some of these improvements with a gas sensor and a supercontiuum source. It should also be possible to exploit other optical properties of the aerogel itself, including the ability to functionalise it with dopants [26

C. A. Morris, M. L. Anderson, R. M. Stroud, C. I. Merzbacher, and D. R. Rolison, “Silica sol as a nanoglue: flexible synthesis of composite aerogels,” Science 284(5414), 622–624 (1999). [CrossRef] [PubMed]

Acknowledgements

The authors thank P. Reddish, Y. H. Yap, N. Wheeler, P. Mosley, and M. Rollings for useful discussions. This work is funded by the UK Engineering and Physical Sciences Research Council (EPSRC). T. A. Birks thanks the Leverhulme Trust for a Research Fellowship.

References and links

1.	H. S. MacKenzie and F. P. Payne, “Evanescent field amplification in a tapered single-mode optical fibre,” Electron. Lett. 26(2), 130–132 (1990). [CrossRef]
2.	J. Bures and R. J. Ghosh, “Power density of the evanescent field in the vicinity of a tapered fiber,” J. Opt. Soc. Am. A 16(8), 1992–1996 (1999). [CrossRef]
3.	L. M. Tong, R. R. Gattass, J. B. Ashcom, S. L. He, J. Y. Lou, M. Y. Shen, I. Maxwell, and E. Mazur, “Subwavelength-diameter silica wires for low-loss optical wave guiding,” Nature 426(6968), 816–819 (2003). [CrossRef] [PubMed]
4.	G. Brambilla, F. Xu, P. Horak, Y. Jung, F. Koizumi, N. P. Sessions, E. Koukharenko, X. Feng, G. S. Murugan, J. S. Wilkinson, and D. J. Richardson, “Optical fiber nanowires and microwires: fabrication and applications,” Adv. Opt. Photon. 1(1), 107–161 (2009). [CrossRef]
5.	S. G. Leon-Saval, T. A. Birks, W. J. Wadsworth, P. St. J. Russell, and M. W. Mason, “Supercontinuum generation in submicron fibre waveguides,” Opt. Express 12(13), 2864–2869 (2004). [CrossRef] [PubMed]
6.	G. Brambilla and D. N. Payne, “The ultimate strength of glass silica nanowires,” Nano Lett. 9(2), 831–835 (2009). [CrossRef] [PubMed]
7.	P. Polynkin, A. Polynkin, N. Peyghambarian, and M. Mansuripur, “Evanescent field-based optical fiber sensing device for measuring the refractive index of liquids in microfluidic channels,” Opt. Lett. 30(11), 1273–1275 (2005). [CrossRef] [PubMed]
8.	J. Villatoro and D. Monzón-Hernández, “Fast detection of hydrogen with nano fiber tapers coated with ultra thin palladium layers,” Opt. Express 13(13), 5087–5092 (2005). [CrossRef] [PubMed]
9.	L. M. Tong, J. Y. Lou, R. R. Gattass, S. L. He, X. W. Chen, L. Liu, and E. Mazur, “Assembly of silica nanowires on silica aerogels for microphotonic devices,” Nano Lett. 5(2), 259–262 (2005). [CrossRef] [PubMed]
10.	Y. Li and L. M. Tong, “Mach-Zehnder interferometers assembled with optical microfibers or nanofibers,” Opt. Lett. 33(4), 303–305 (2008). [CrossRef] [PubMed]
11.	D. I. Yeom, E. C. Mägi, M. R. E. Lamont, M. A. F. Roelens, L. Fu, and B. J. Eggleton, “Low-threshold supercontinuum generation in highly nonlinear chalcogenide nanowires,” Opt. Lett. 33(7), 660–662 (2008). [CrossRef] [PubMed]
12.	M. Sumetsky, “Basic Elements for Microfiber Photonics: Micro/Nanofibers and Microfiber Coil Resonators,” J. Lightwave Technol. 26(1), 21–27 (2008). [CrossRef]
13.	G. Vienne, Y. Li, and L. M. Tong, “Effect of Host Polymer on Microfiber Resonator,” IEEE Photon. Technol. Lett. 19(18), 1386–1388 (2007). [CrossRef]
14.	G. Brambilla, F. Xu, and X. Feng, “Fabrication of optical fibre nanowires and their optical and mechanical characterization,” Electron. Lett. 42(9), 517–519 (2006). [CrossRef]
15.	F. Xu and G. Brambilla, “Preservation of micro-optical fibers by embedding,” Jpn. J. Appl. Phys. 47(8), 6675–6677 (2008). [CrossRef]
16.	N. Lou, R. Jha, J. L. Domínguez-Juárez, V. Finazzi, J. Villatoro, G. Badenes, and V. Pruneri, “Embedded optical micro/nano-fibers for stable devices,” Opt. Lett. 35(4), 571–573 (2010). [CrossRef] [PubMed]
17.	G. M. Pajonk, “Transparent silica aerogels,” J. Non-Cryst. Solids 225(1), 307–314 (1998). [CrossRef]
18.	L. M. Xiao, M. D. W. Grogan, S. G. Leon-Saval, R. Williams, R. England, W. J. Wadsworth, and T. A. Birks, “Tapered fibers embedded in silica aerogel,” Opt. Lett. 34(18), 2724–2726 (2009). [CrossRef] [PubMed]
19.	H. Yokogawa and M. Yokoyama, “Hydrophobic silica aerogels,” J. Non-Cryst. Solids 186, 23–29 (1995). [CrossRef]
20.	M. Sumetsky, “How thin can a microfiber be and still guide light?” Opt. Lett. 31(7), 870–872 (2006). [CrossRef] [PubMed]
21.	N. Leventis, I. A. Elder, D. R. Rolison, M. L. Anderson, and C. I. Merzbacher, “Durable Modification of Silica Aerogel Monoliths with Fluorescent 2,7-Diazapyrenium Moieties. Sensing Oxygen near the Speed of Open-Air Diffusion,” Chem. Mater. 11(10), 2837–2845 (1999). [CrossRef]
22.	Y. L. Hoo, W. Jin, C. Z. Shi, H. L. Ho, D. N. Wang, and S. C. Ruan, “Design and modeling of a photonic crystal fiber gas sensor,” Appl. Opt. 42(18), 3509–3515 (2003). [CrossRef] [PubMed]
23.	A. van Brakel, C. Grivas, M. N. Petrovich, and D. J. Richardson, “Micro-channels machined in microstructured optical fibers by femtosecond laser,” Opt. Express 15(14), 8731–8736 (2007). [CrossRef] [PubMed]
24.	A. Roig, E. Molins, E. Rodríguez, S. Martínez, M. Moreno-Mañas, and A. Vallribera, “Superhydrophobic silica aerogels by fluorination at the gel stage,” Chem. Commun. (Camb.) 20(20), 2316–2317 (2004). [CrossRef]
25.	T. Y. Wei, S. Y. Lu, and Y. C. J. Chang, “Transparent, hydrophobic composite aerogels with high mechanical strength and low high-temperature thermal conductivities,” J. Phys. Chem. B 112(38), 11881–11886 (2008). [CrossRef] [PubMed]
26.	C. A. Morris, M. L. Anderson, R. M. Stroud, C. I. Merzbacher, and D. R. Rolison, “Silica sol as a nanoglue: flexible synthesis of composite aerogels,” Science 284(5414), 622–624 (1999). [CrossRef] [PubMed]
27.	M. K. Yang, R. H. French, and E. W. J. Tokarsky, “Optical properties of Teflon AF amorphous fluoropolymers,” J. Micro/Nanolith. MEMS MOEMS 7(3), 033010 (2008). [CrossRef]
28.	T. Bellunato, M. Calvi, C. Matteuzzi, M. Musy, D. L. Perego, and B. Storaci, “Refractive index dispersion law of silica aerogel,” Eur. Phys. J. C 52(3), 759–764 (2007). [CrossRef]

OCIS Codes
(060.2340) Fiber optics and optical communications : Fiber optics components
(060.2370) Fiber optics and optical communications : Fiber optics sensors
(060.4370) Fiber optics and optical communications : Nonlinear optics, fibers

ToC Category:
Fiber Optics and Optical Communications

History
Original Manuscript: November 11, 2010
Revised Manuscript: December 20, 2010
Manuscript Accepted: December 25, 2010
Published: January 5, 2011

Citation
Limin Xiao, M. D. W. Grogan, W. J. Wadsworth, R. England, and T. A. Birks, "Stable low-loss optical nanofibres embedded in hydrophobic aerogel," Opt. Express 19, 764-769 (2011)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-19-2-764

Sort: Author | Year | Journal | Reset

References

H. S. MacKenzie and F. P. Payne, “Evanescent field amplification in a tapered single-mode optical fibre,” Electron. Lett. 26(2), 130–132 (1990). [CrossRef]
J. Bures and R. J. Ghosh, “Power density of the evanescent field in the vicinity of a tapered fiber,” J. Opt. Soc. Am. A 16(8), 1992–1996 (1999). [CrossRef]
L. M. Tong, R. R. Gattass, J. B. Ashcom, S. L. He, J. Y. Lou, M. Y. Shen, I. Maxwell, and E. Mazur, “Subwavelength-diameter silica wires for low-loss optical wave guiding,” Nature 426(6968), 816–819 (2003). [CrossRef] [PubMed]
G. Brambilla, F. Xu, P. Horak, Y. Jung, F. Koizumi, N. P. Sessions, E. Koukharenko, X. Feng, G. S. Murugan, J. S. Wilkinson, and D. J. Richardson, “Optical fiber nanowires and microwires: fabrication and applications,” Adv. Opt. Photon. 1(1), 107–161 (2009). [CrossRef]
S. G. Leon-Saval, T. A. Birks, W. J. Wadsworth, P. St. J. Russell, and M. W. Mason, “Supercontinuum generation in submicron fibre waveguides,” Opt. Express 12(13), 2864–2869 (2004). [CrossRef] [PubMed]
G. Brambilla and D. N. Payne, “The ultimate strength of glass silica nanowires,” Nano Lett. 9(2), 831–835 (2009). [CrossRef] [PubMed]
P. Polynkin, A. Polynkin, N. Peyghambarian, and M. Mansuripur, “Evanescent field-based optical fiber sensing device for measuring the refractive index of liquids in microfluidic channels,” Opt. Lett. 30(11), 1273–1275 (2005). [CrossRef] [PubMed]
J. Villatoro and D. Monzón-Hernández, “Fast detection of hydrogen with nano fiber tapers coated with ultra thin palladium layers,” Opt. Express 13(13), 5087–5092 (2005). [CrossRef] [PubMed]
L. M. Tong, J. Y. Lou, R. R. Gattass, S. L. He, X. W. Chen, L. Liu, and E. Mazur, “Assembly of silica nanowires on silica aerogels for microphotonic devices,” Nano Lett. 5(2), 259–262 (2005). [CrossRef] [PubMed]
Y. Li and L. M. Tong, “Mach-Zehnder interferometers assembled with optical microfibers or nanofibers,” Opt. Lett. 33(4), 303–305 (2008). [CrossRef] [PubMed]
D. I. Yeom, E. C. Mägi, M. R. E. Lamont, M. A. F. Roelens, L. Fu, and B. J. Eggleton, “Low-threshold supercontinuum generation in highly nonlinear chalcogenide nanowires,” Opt. Lett. 33(7), 660–662 (2008). [CrossRef] [PubMed]
M. Sumetsky, “Basic Elements for Microfiber Photonics: Micro/Nanofibers and Microfiber Coil Resonators,” J. Lightwave Technol. 26(1), 21–27 (2008). [CrossRef]
G. Vienne, Y. Li, and L. M. Tong, “Effect of Host Polymer on Microfiber Resonator,” IEEE Photon. Technol. Lett. 19(18), 1386–1388 (2007). [CrossRef]
G. Brambilla, F. Xu, and X. Feng, “Fabrication of optical fibre nanowires and their optical and mechanical characterization,” Electron. Lett. 42(9), 517–519 (2006). [CrossRef]
F. Xu and G. Brambilla, “Preservation of micro-optical fibers by embedding,” Jpn. J. Appl. Phys. 47(8), 6675–6677 (2008). [CrossRef]
N. Lou, R. Jha, J. L. Domínguez-Juárez, V. Finazzi, J. Villatoro, G. Badenes, and V. Pruneri, “Embedded optical micro/nano-fibers for stable devices,” Opt. Lett. 35(4), 571–573 (2010). [CrossRef] [PubMed]
G. M. Pajonk, “Transparent silica aerogels,” J. Non-Cryst. Solids 225(1), 307–314 (1998). [CrossRef]
L. M. Xiao, M. D. W. Grogan, S. G. Leon-Saval, R. Williams, R. England, W. J. Wadsworth, and T. A. Birks, “Tapered fibers embedded in silica aerogel,” Opt. Lett. 34(18), 2724–2726 (2009). [CrossRef] [PubMed]
H. Yokogawa and M. Yokoyama, “Hydrophobic silica aerogels,” J. Non-Cryst. Solids 186, 23–29 (1995). [CrossRef]
M. Sumetsky, “How thin can a microfiber be and still guide light?” Opt. Lett. 31(7), 870–872 (2006). [CrossRef] [PubMed]
N. Leventis, I. A. Elder, D. R. Rolison, M. L. Anderson, and C. I. Merzbacher, “Durable Modification of Silica Aerogel Monoliths with Fluorescent 2,7-Diazapyrenium Moieties. Sensing Oxygen near the Speed of Open-Air Diffusion,” Chem. Mater. 11(10), 2837–2845 (1999). [CrossRef]
Y. L. Hoo, W. Jin, C. Z. Shi, H. L. Ho, D. N. Wang, and S. C. Ruan, “Design and modeling of a photonic crystal fiber gas sensor,” Appl. Opt. 42(18), 3509–3515 (2003). [CrossRef] [PubMed]
A. van Brakel, C. Grivas, M. N. Petrovich, and D. J. Richardson, “Micro-channels machined in microstructured optical fibers by femtosecond laser,” Opt. Express 15(14), 8731–8736 (2007). [CrossRef] [PubMed]
A. Roig, E. Molins, E. Rodríguez, S. Martínez, M. Moreno-Mañas, and A. Vallribera, “Superhydrophobic silica aerogels by fluorination at the gel stage,” Chem. Commun. (Camb.) 20(20), 2316–2317 (2004). [CrossRef]
T. Y. Wei, S. Y. Lu, and Y. C. J. Chang, “Transparent, hydrophobic composite aerogels with high mechanical strength and low high-temperature thermal conductivities,” J. Phys. Chem. B 112(38), 11881–11886 (2008). [CrossRef] [PubMed]
C. A. Morris, M. L. Anderson, R. M. Stroud, C. I. Merzbacher, and D. R. Rolison, “Silica sol as a nanoglue: flexible synthesis of composite aerogels,” Science 284(5414), 622–624 (1999). [CrossRef] [PubMed]
M. K. Yang, R. H. French, and E. W. J. Tokarsky, “Optical properties of Teflon AF amorphous fluoropolymers,” J. Micro/Nanolith. MEMS MOEMS 7(3), 033010 (2008). [CrossRef]
T. Bellunato, M. Calvi, C. Matteuzzi, M. Musy, D. L. Perego, and B. Storaci, “Refractive index dispersion law of silica aerogel,” Eur. Phys. J. C 52(3), 759–764 (2007). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Click here to see a list of articles that cite this paper