OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 19, Iss. 23 — Nov. 7, 2011
  • pp: 23162–23170
« Show journal navigation

Low-loss, high-index-contrast Si3N4/SiO2 optical waveguides for optical delay lines in microwave photonics signal processing

Leimeng Zhuang, David Marpaung, Maurizio Burla, Willem Beeker, Arne Leinse, and Chris Roeloffzen  »View Author Affiliations


Optics Express, Vol. 19, Issue 23, pp. 23162-23170 (2011)
http://dx.doi.org/10.1364/OE.19.023162


View Full Text Article

Acrobat PDF (1782 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We report the design and characterization of Si3N4/SiO2 optical waveguides which are specifically developed for optical delay lines in microwave photonics (MWP) signal processing applications. The waveguide structure consists of a stack of two Si3N4 stripes and SiO2 as an intermediate layer. Characterization of the waveguide propagation loss was performed in race track-shaped optical ring resonators (ORRs) with a free-spectral range of 20 GHz and a bending radius varied from 50 μm to 125 μm. A waveguide propagation loss as low as 0.095 dB/cm was measured in the ORRs with bend radii ≥ 70 μm. Using the waveguide technology two types of RF-modulated optical sideband filters with high sideband suppression and small transition band consisting of an Mach-Zehnder interferometer and ORRs are also demonstrated. These results demonstrate the potential of the waveguide technology to be applied to construct compact on-chip MWP signal processors.

© 2011 OSA

1. Introduction

Low-loss optical waveguides and their characterization techniques have been widely reported [15

15. H. Takahashi, “Planar lightwave circuit devices for optical communication: present and future,” Proc. SPIE 5246, 520–531 (2003). [CrossRef]

18

18. M. John, Senior, Optical Fiber Communications Principles and Practice, 2nd ed. (Pearson Education, 1992).

]. Extremely low propagation loss in the figure of sub 1 dB/m have been reported in [17

17. R. Adar, M. Serbin, and V. Mizrahi, “Less than 1 dB per meter propagation loss of silica waveguides measured using a ring resonator,” J. Lightwave Technol. 12(8), 1369–1372 (1994). [CrossRef]

,19

19. T. Kominato, Y. Hida, M. Itoh, H. Takahashi, S. Sohma, T. Kitoh, and Y. Hibino, “Extremely low-loss (0.3 dB/m) and long silica-based waveguides with large width and clothoid curve connection,” in Proceedings of ECOC (2004).

] but this has been shown in optical waveguides with very low refractive index contrast (<1%). Such a low contrast will lead to a large minimum bending radius and subsequently a large footprint of a photonic chip with moderate to high complexities. On the other hand, high-index-contrast optical waveguide in silicon-on-insulator (SOI) or InP technologies have shown their applications with very low bending radii (<30 μm [20

20. M. Gnan, S. Thoms, D. S. Macintyre, R. M. De la Rue, and M. Sorel, “Fabrication of low-loss photonic wires in silicon-on-insulator using hydrogen silsesquioxane electron-beam resist,” Electron. Lett. 44(2), 115–116 (2008). [CrossRef]

,21

21. Y. Barbarin, X. J. M. Leijtens, E. A. J. M. Bente, C. M. Louzao, J. R. Kooiman, and M. K. Smit, “Extremely small AWG demultiplexer fabricated on InP by using a double-etch process,” IEEE Photon. Technol. Lett. 16(11), 2478–2480 (2004). [CrossRef]

]), however, these are accompanied by high waveguide losses (>1 dB/cm [20

20. M. Gnan, S. Thoms, D. S. Macintyre, R. M. De la Rue, and M. Sorel, “Fabrication of low-loss photonic wires in silicon-on-insulator using hydrogen silsesquioxane electron-beam resist,” Electron. Lett. 44(2), 115–116 (2008). [CrossRef]

,21

21. Y. Barbarin, X. J. M. Leijtens, E. A. J. M. Bente, C. M. Louzao, J. R. Kooiman, and M. K. Smit, “Extremely small AWG demultiplexer fabricated on InP by using a double-etch process,” IEEE Photon. Technol. Lett. 16(11), 2478–2480 (2004). [CrossRef]

]). The low-loss waveguides in these technologies have also been greatly investigated and realized (in the order of 0.3 dB/cm [22

22. J. Cardenas, C. B. Poitras, J. T. Robinson, K. Preston, L. Chen, and M. Lipson, “Low loss etchless silicon photonic waveguides,” Opt. Express 17(6), 4752–4757 (2009). [CrossRef] [PubMed]

,23

23. M. Lysevych, H. H. Tan, F. Karouta, and C. Jagadish, “Single-step RIE fabrication process of low loss InP waveguide using CH4/H2 chemistry,” J. Electrochem. Soc. 158(3), H281–H284 (2011). [CrossRef]

]), an example of which has demonstrated a small bend radius as well (down to 50 µm [22

22. J. Cardenas, C. B. Poitras, J. T. Robinson, K. Preston, L. Chen, and M. Lipson, “Low loss etchless silicon photonic waveguides,” Opt. Express 17(6), 4752–4757 (2009). [CrossRef] [PubMed]

]). In this paper, we investigate the performance of an optical waveguide structure fabricated in the TriPleX technology [24

24. F. Morichetti, A. Melloni, M. Martinelli, R. É. G. Heideman, A. Leinse, D. H. Geuzebroek, and A. Borreman, “Box-shaped dielectric waveguides: a new concept in integrated optics?” J. Lightwave Technol. 25(9), 2579–2589 (2007). [CrossRef]

]. Very recently an optical waveguide of this technology has been shown to have a propagation loss as low as 8-9 dB/m at a bending radius of 0.5 mm [25

25. J. F. Bauters, M. J. Heck, D. John, D. Dai, M. C. Tien, J. S. Barton, A. Leinse, R. G. Heideman, D. J. Blumenthal, and J. E. Bowers, “Ultra-low-loss high-aspect-ratio Si3N4 waveguides,” Opt. Express 19(4), 3163–3174 (2011). [CrossRef] [PubMed]

]. It was predicted that a loss of 0.17 dB/cm can be achieved if the bending radius is reduced to 200 μm. This was shown with a single stripe of Si3N4 waveguide with SiO2 cladding. Such a structure allows only a low mode confinement. In this work, we characterize a novel optical waveguide structure with two stripes of Si3N4, thereby increasing the mode confinement significantly and allowing low propagation loss at even smaller bend radii. The rest of this paper is organized as follows: in Section 2, the optical waveguide properties are described. The method to characterize the propagation loss of the optical waveguides using the optical ring resonators (ORRs) are presented in Section 3. In Section 4, the characterization of two structures of RF-modulated optical sideband filters fabricated using the optical waveguide technology are presented. In the final section the potential of constructing a high complexity MWP processor like an optical beamformer using the novel technology is discussed. The paper closes with conclusions.

2. Waveguide properties

2.1 Waveguide geometry

The optical waveguide consists of two strips of Si3N4 stacked on top of each other with SiO2 as an intermediate layer and cladding material which have been produced using TriPleX technology. A scanning electron microscope (SEM) image of the waveguide cross section is shown in Fig. 1
Fig. 1 A scanning electron microscope (SEM) image of the waveguide cross section
. The use of this two-strip geometry increases the effective index of the optical mode as compared to a single strip geometry, thus increasing the confinement of the mode and thereby reducing the bend loss. The width of the strips is designed to be 1.5 µm, and the thicknesses of the Si3N4 layers and the SiO2 intermediate layer are designed to be 170 nm and 500 nm, respectively. This is optimized to result in a high effective index of the mode while the waveguide only supports a single mode at a wavelength of 1550 nm. Besides, this waveguide geometry design was also chosen in order to match TriPleX production standards which increase device reproducibility. The waveguide geometry supports a single mode of TE and TM polarized light. Due to a birefringence of about 0.053, the TM mode is much less confined and, therefore, experiences much more loss in bend sections as compared to the TE mode. Hence, in the following discussions of this paper, only TE polarized light is considered.

2.2 ORR device layout

To characterize the propagation loss of the waveguide, race track-shaped ORR test structures have been fabricated which have a waveguide width of 1.5 µm, a group index of 1.72, a circumference of 8783 µm, and bending radii varying from 50 µm to 125 µm. The resulting free spectral range (FSR) of the ORR is 20 GHz. The light is coupled into and out of the ring path through an Mach-Zehnder interferometer (MZI)-based power coupler. A schematic of the waveguide architecture of an ORR is depicted in Fig. 2a
Fig. 2 (a) schematic of the waveguide architecture of an ORR, (b) two heaters are placed on top of two waveguide sections of the ORR to enable full programmability of the device.
. Furthermore, the device is realized with full programmability by means of thermo-optic tuning mechanism. As depicted in Fig. 2b, two heaters are placed on top of two waveguide sections of the ORR: the upper one controls an additional round-trip phase shift of the ring path; the lower one controls the power coupling ratio of the MZI. To ensure sufficient tuning range of the power coupling ratio, two directional couplers in the MZI are carefully designed to approximate the desired −3 dB power coupling ratio such that the MZI reaches a power extinction ratio larger than 15 dB.

3. Waveguide propagation loss characterization

The working principle of ORR-based delay lines has been elaborated in [9

9. C. G. H. L. Zhuang, A. Roeloffzen, M. Meijerink, D. Burla, A. Marpaung, M. Leinse, R. G. Hoekman, Heideman, and W. van Etten, “Novel ring resonator-based integrated photonic beamformer for broadband phased-array receive antennas-Part II: experimental prototype,” J. Lightwave Technol. 28(1), 19–31 (2010). [CrossRef]

,26

26. L. Zhuang, Ring Resonator-Based Broadband Photonic Beam Former for Phased Array Antennas, PhD thesis (University of Twente, Enschede, The Netherlands, 2009).

]. The general transfer function H(Ω) of an ORR and its frequency responses in terms of power transmission P(Ω) in dB and number of effective delay round-trips τ(Ω) are given by
H(Ω)=1κrej(Ω+ϕ)11κrej(Ω+ϕ)
(1)
P(Ω)dB=L(Ω)dB=10log10(1κ+r22r1κcos(Ω+ϕ)1+r2(1κ)2r1κcos(Ω+ϕ))
(2)
and
τ(Ω)=T(Ω)TR=r1κcos(Ω+ϕ)r21κ12r1κcos(Ω+ϕ)+r21κ+r2r1κcos(Ω+ϕ)1κ2r1κcos(Ω+ϕ)+r2
(3)
respectively, where Ω = 2πffFSR is the angular frequency of the light normalized to the free spectral range (FSR) of the ORR, κ is the power coupling coefficient, ϕ is the additional round-trip phase shift, L(Ω) = −P(Ω) in dB signifies the power loss of the ORR, T(Ω) indicates the effective time delay (group delay), TR is the characteristic round-trip time delay of the ORR, and r is defined as the round-trip amplitude transmission coefficient which is determined by the waveguide propagation loss Lwg in dB/cm, and the circumference of the ring path Cr in cm, as in the following equation

r=10(LwgCr)/20
(4)

Furthermore, TR equals the reciprocal of ΔfFSR and is determined by the circumference of the ring path Cr, the group index of the waveguide ng, and the speed of the light in vacuum c0 as in the equation

TR=1ΔfFSR=Crngc0
(5)

Knowing the working principle of an ORR and using the close approximation of a linear relation of power loss L(Ω) to effective delay path length D(Ω) = Crτ(Ω) for low round-trip loss scenario (Lwg Cr < 0.5 dB) [26

26. L. Zhuang, Ring Resonator-Based Broadband Photonic Beam Former for Phased Array Antennas, PhD thesis (University of Twente, Enschede, The Netherlands, 2009).

], one can retrieve the waveguide propagation loss Lwg from a given pair of P(Ω) and τ(Ω) by applying the equation
Lwg=dL(Ω)dD(Ω)=-dP(Ω)Crdτ(Ω)=-ΔPon-offCrΔτon-off(κc<κ<1)
(6)
where “on” and “off” indicate the on-resonance frequency (Ω + ϕ = 2nπ, n is integer) and the off-resonance frequency (Ω + ϕ = 2nπ ± π) of the ORR, respectively; the condition κc (critical coupling coefficient) < κ < 1 ensures the resonance enhancement effect in the ORR, which is characterized by a delay maximum/power transmission minimum at the on-resonance frequencies and a delay minimum/power transmission maximum at the off-resonance frequencies [9

9. C. G. H. L. Zhuang, A. Roeloffzen, M. Meijerink, D. Burla, A. Marpaung, M. Leinse, R. G. Hoekman, Heideman, and W. van Etten, “Novel ring resonator-based integrated photonic beamformer for broadband phased-array receive antennas-Part II: experimental prototype,” J. Lightwave Technol. 28(1), 19–31 (2010). [CrossRef]

,26

26. L. Zhuang, Ring Resonator-Based Broadband Photonic Beam Former for Phased Array Antennas, PhD thesis (University of Twente, Enschede, The Netherlands, 2009).

]. These characteristic maximums and minimums can be addressed by frequency sweeping over one FSR of the ORR. In practice, ΔPon-off can be measured by means of a CW laser with sweeping wavelength λ and an optical power meter, or alternatively by measuring the magnitude response of an RF frequency fRF externally modulated on a wavelength-sweeping CW laser, and then using the square-law relation of the optical detector to calculate ΔPon-off from the measured magnitude response ARF(λ) in dB by

ΔPon-off=ARF(λon)ARF(λoff)2
(7)

To measure Δτon-off, the so-called RF phase-shift method is needed [27

27. C. G. H. Roeloffzen, L. Zhuang, R. G. Heideman, A. Borreman, and W. van Etten, “Ring resonator-based tunable optical delay line in LPCVD waveguide technology,” in Proceedings Symposium IEEE/LEOS Benelux Chapter, 2005 (IEEE/LEOS, 2005), pp. 79–82.

]. Similar to the second method for ΔPon-off measurement, a wavelength-sweeping CW laser is externally modulated by an RF frequency fRF and the measured RF phase response ϕRF(λ) in degree can be translated into Δτon-off by using the equation

Δτon-off=ΔTon-offTR(ϕRF(λon)ϕRF(λoff))360ofRFTR
(8)

In this work ARF(λ) and ϕRF(λ) are obtained using the setup illustrated in Fig. 3
Fig. 3 Illustration of measurement setup
. An Agilent N5230 vector network analyzer was used to generate the RF frequency and measure the detected relative amplitude and phase of the RF signal. An EM4 1550 nm/100 mW CW laser was driven by a ramping current source and operated as a high resolution wavelength-sweeping CW light source. The optical modulation and detection were implemented using an Avanex Powerlog20 Mach-Zehnder modulator and an Emcore 20 GHz-bandwidth optical detector, respectively. Given that the ORR filters have an FSR of 20 GHz, a wavelength resolution of 0.0008 nm (≈100 MHz) was chosen to ensure accurate acquisitions of the frequency response of the ORR filters. Correspondingly, an fRF = 50 MHz, which yields measurement results robust to the system phase noise, was used to achieve sufficient measurement accuracy. To further increase the accuracy of the resulting waveguide propagation loss, the same measurements were repeated for different κ’s of the ORR, and the final result was obtained by means of averaging.

The waveguide propagation losses extracted from the measurements and the theoretical calculations are depicted in Fig. 4
Fig. 4 Waveguide propagation losses versus different bend radii in the race track-shaped ORR (inset: measured ORR frequency responses fitted by the theoretical counterparts with matched waveguide loss)
. The theoretical values are calculated using the equation
Lwg(R)=2πRLbd(R)+CrLstCr
(9)
where R is the bend radius of the ORRs, Lbd(R) and Lst are defined to be the optical power loss per unit waveguide length due to bend radiation and scattering effect, respectively. The determination of Lbd(R) and Lst (λ = 1550 nm) was performed using the loss modeling approach described in [25

25. J. F. Bauters, M. J. Heck, D. John, D. Dai, M. C. Tien, J. S. Barton, A. Leinse, R. G. Heideman, D. J. Blumenthal, and J. E. Bowers, “Ultra-low-loss high-aspect-ratio Si3N4 waveguides,” Opt. Express 19(4), 3163–3174 (2011). [CrossRef] [PubMed]

] in association with the characteristic parameters of the waveguide technology. In the inset of Fig. 4 a pair of measured frequency responses of the ORR are fitted by their theoretical counterparts (Eq. (2) and 3, using κ as the fitting parameter) with respect to the matched round-trip loss. The fitting result clearly verifies the accuracy of the measurement approach being used.

As shown in the result, the maximum waveguide propagation loss was measured to be 0.12 dB/cm in the ORR with a bend radius of 50 µm, and an average waveguide propagation loss as low as 0.095 dB/cm was achieved for the bend radii ≥ 70 µm where the loss contribution of the bend radiation is negligible compared to the scattering loss of the waveguide. Note that in Eq. (9) we assumed that the excess insertion loss of the coupling section between the waveguide bus and the ring path is negligible. Therefore, it is likely that the waveguide propagation loss has been overestimated. To our knowledge, this waveguide significantly outperforms the low-loss waveguides in other common high-index-contrast waveguide technologies [20

20. M. Gnan, S. Thoms, D. S. Macintyre, R. M. De la Rue, and M. Sorel, “Fabrication of low-loss photonic wires in silicon-on-insulator using hydrogen silsesquioxane electron-beam resist,” Electron. Lett. 44(2), 115–116 (2008). [CrossRef]

23

23. M. Lysevych, H. H. Tan, F. Karouta, and C. Jagadish, “Single-step RIE fabrication process of low loss InP waveguide using CH4/H2 chemistry,” J. Electrochem. Soc. 158(3), H281–H284 (2011). [CrossRef]

]. With this demonstration the waveguide technology proves its capability to realize compact, low-loss on-chip functionalities.

4. Characterization of optical sideband filter

To further demonstrate the functionalities of the waveguide technology for MWP signal processing, two types of RF-modulated optical sideband filters (OSBFs) with high frequency selectivity have been fabricated and characterized. One filter consists of an asymmetric MZI with an ORR inserted in its shorter arm [28

28. K. Oda, N. Takato, H. Toba, and K. Nosu, “A wide-band guided-wave periodic multi/demultiplexer with a ring resonator for optical FDM transmission system,” J. Lightwave Technol. 6(6), 1016–1023 (1988). [CrossRef]

]. The other is an upgraded version of the first one obtained by adding a second ORR to the longer arm of the asymmetric MZI [29

29. Z. Wang, S.-J. Chang, C.-Y. Ni, and Y. J. Chen, “A high-performance ultracompact optical interleaver based on double-ring assisted Mach-Zehnder interferometer,” IEEE Photon. Technol. Lett. 19(14), 1072–1074 (2007). [CrossRef]

]. Both filters were designed with an FSR of 6.7 GHz and full filter-shape programmability by using the thermo-optic tuning mechanism of the waveguide. For the mask layout design of both filters, a waveguide bend radius of 125 µm was used, which results in footprints of 0.3 × 1.5 cm (MZI + 1 ORR) and 0.4 × 1.5 cm (MZI + 2 ORRs). The insets of Fig. 5
Fig. 5 Measured filter shapes of the single and double ring-assisted MZI (Inset: schematic of the filter architecture and mask layout design)
depict the schematics of the filter architectures and the corresponding mask layouts. The measured filter shapes are shown in Fig. 5.

In agreement with the filter design [28

28. K. Oda, N. Takato, H. Toba, and K. Nosu, “A wide-band guided-wave periodic multi/demultiplexer with a ring resonator for optical FDM transmission system,” J. Lightwave Technol. 6(6), 1016–1023 (1988). [CrossRef]

,29

29. Z. Wang, S.-J. Chang, C.-Y. Ni, and Y. J. Chen, “A high-performance ultracompact optical interleaver based on double-ring assisted Mach-Zehnder interferometer,” IEEE Photon. Technol. Lett. 19(14), 1072–1074 (2007). [CrossRef]

], the realized filter with one ORR demonstrates a flattened passband and significant stopband suppression with the allocation of the three zeros clearly displayed; the filter with two ORRs demonstrates a significantly improved frequency selectivity by means of introducing two more zeros in the stopband using the additional ORR. In Fig. 5 the measured filter shapes are normalized to their passband transmission. For these devices the waveguide technology allows for low on-chip losses. However, due to mode profile mismatch, high fiber-chip coupling losses of about 10 dB/facet will occur when using regular single mode fibers with a mode field diameter of 10.4 µm. As an effective solution, a linearly tapered waveguide section can be introduced to every facet. This can be realized by additional production steps, and in theory minimizes the coupling loss to 0.5 dB/facet.

5. Design of an optical beamformer chip (an example of on-chip MWP signal processor)

With the demonstrated functionalities and performances, the waveguide technology investigated in this work proves its potential to be applied to construct complex on-chip MWP signal processors. As an illustration, the design of an on-chip MWP signal processor using the ORRs and OSBFs as the basic building blocks, i.e. an optical beamformer chip for phased array antennas [8

8. A. Meijerink, C. G. H. Roeloffzen, R. Meijerink, D. A. I. Leimeng Zhuang, M. J. Marpaung, M. Bentum, J. Burla, P. Verpoorte, A. Jorna, A. Hulzinga, and W. van Etten, “Novel ring resonator-based integrated photonic beamformer for broadband phased-array receive antennas-Part I: design and performance analysis,” J. Lightwave Technol. 28(1), 3–18 (2010). [CrossRef]

,9

9. C. G. H. L. Zhuang, A. Roeloffzen, M. Meijerink, D. Burla, A. Marpaung, M. Leinse, R. G. Hoekman, Heideman, and W. van Etten, “Novel ring resonator-based integrated photonic beamformer for broadband phased-array receive antennas-Part II: experimental prototype,” J. Lightwave Technol. 28(1), 19–31 (2010). [CrossRef]

,26

26. L. Zhuang, Ring Resonator-Based Broadband Photonic Beam Former for Phased Array Antennas, PhD thesis (University of Twente, Enschede, The Netherlands, 2009).

], is described in the following. The functionalities of such an optical beamformer chip have been described in [9

9. C. G. H. L. Zhuang, A. Roeloffzen, M. Meijerink, D. Burla, A. Marpaung, M. Leinse, R. G. Hoekman, Heideman, and W. van Etten, “Novel ring resonator-based integrated photonic beamformer for broadband phased-array receive antennas-Part II: experimental prototype,” J. Lightwave Technol. 28(1), 19–31 (2010). [CrossRef]

,11

11. C. G. H. Roeloffzen, A. Meijerink, L. Zhuang, D. A. I. Marpaung, R. G. Heideman, A. Leinse, M. Hoekman, and W. van Etten, “Integrated photonic beamformer employing continuously tunable ring resonator-based delays in CMOS-compatible LPCVD waveguide technology,” Proc. SPIE 7135, 71351K (2008). [CrossRef]

], where an OSBF and an optical carrier reinsertion coupler are incorporated together with the primary signal-combining circuit using ORR-based delay lines. The desired chip is intended to serve for a phased array antenna system for mobile broadband satellite communications [10

10. D. Marpaung, L. Zhuang, M. Burla, C. Roeloffzen, J. Verpoorte, H. Schippers, A. Hulzinga, P. Jorna, W. P. Beeker, A. Leinse, R. Heideman, B. Noharet, Q. Wang, B. Sanadgol, and R. Baggen, “Towards a broadband and squint-free Ku-band phased array antenna system for airborne satellite communications,” in Proceedings of the 5th European Conference on Antennas and Propagation (EuCAP) (2011), pp. 2774–2778 .

]. It is required to provide 16 inputs, 4.5 GHz optical bandwidth, and a maximum delay of 290 ps. Correspondingly, this is translated into a functional design which consists of a 16 × 1 binary-tree combining circuit inserted symmetrically with a total of 40 ORR-based delay lines, an OSBF using an asymmetric MZI with two ORRs, and an optical carrier reinsertion coupler. The schematic of the beamformer architecture is depicted in Fig. 6a
Fig. 6 (a) schematic of the designed 16 × 1 OBFN chip; (b) chip mask layout using waveguide bend radius of 125 µm
. Using the waveguide bend radius of 125 µm, a chip mask layout has been generated as shown in Fig. 6b, which has a footprint as small as 0.7 × 2.2 cm. This features a size reduction of nearly 10 times compared to a previously reported optical beamformer chip with even lower complexity [9

9. C. G. H. L. Zhuang, A. Roeloffzen, M. Meijerink, D. Burla, A. Marpaung, M. Leinse, R. G. Hoekman, Heideman, and W. van Etten, “Novel ring resonator-based integrated photonic beamformer for broadband phased-array receive antennas-Part II: experimental prototype,” J. Lightwave Technol. 28(1), 19–31 (2010). [CrossRef]

].

6. Conclusion

We have reported the design and characterization of Si3N4/SiO2 optical waveguides which are specifically developed for optical delay lines in MWP signal processing applications. A record low waveguide propagation loss of 0.095 dB/cm has been measured in compact, race track-shaped ORRs with a circumference of 8783 μm (20 GHz FSR) and bend radii ≥ 70 μm. Using this waveguide technology two types of RF-modulated optical sideband filters have been demonstrated. These results demonstrate the potential of the waveguide technology to be applied to construct compact on-chip MWP signal processors.

Acknowledgments

The research described in this paper is carried out within the Dutch Point One R&D Innovation Project: Broadband Satellite Communication Services on High-Speed Vehicles, the SANDRA project in Large Scale Integrating Project for the European Commission in the 7th Framework: Integrated Approach to Network Centric Aircraft Communications for Global Aircraft Operations, and the Dutch national-based MEMPHIS project: Merging Electronics and Micro & Nano-Photonics in Integrated Systems. The authors gratefully acknowledge the support of the funding institutes for those three projects.

References and links

1.

J. Capmany and D. Novak, “Microwave photonics combines two worlds,” Nat. Photonics 1(6), 319–330 (2007). [CrossRef]

2.

A. Seeds, “Microwave photonics,” IEEE Trans. Microw. Theory Tech. 50(3), 877–887 (2002). [CrossRef]

3.

J. Capmany, B. Ortega, D. Pastor, and S. Sales, “Discrete-Time Optical Processing of Microwave Signals,” J. Lightwave Technol. 23(2), 702–723 (2005). [CrossRef]

4.

R. Minasian, “Photonic signal processing of microwave signals,” IEEE Trans. Microw. Theory Tech. 54(2), 832–846 (2006). [CrossRef]

5.

N. N. Feng, P. Dong, D. Feng, W. Qian, H. Liang, D. C. Lee, J. B. Luff, A. Agarwal, T. Banwell, R. Menendez, P. Toliver, T. K. Woodward, and M. Asghari, “Thermally-efficient reconfigurable narrowband RF-photonic filter,” Opt. Express 18(24), 24648–24653 (2010). [CrossRef] [PubMed]

6.

S. Ibrahim, N. K. Fontaine, S. S. Djordjevic, B. Guan, T. Su, S. Cheung, R. P. Scott, A. T. Pomerene, L. L. Seaford, C. M. Hill, S. Danziger, Z. Ding, K. Okamoto, and S. J. B. Yoo, “Demonstration of a fast-reconfigurable silicon CMOS optical lattice filter,” Opt. Express 19(14), 13245–13256 (2011). [CrossRef] [PubMed]

7.

R. S. Guzzon, E. J. Norberg, J. S. Parker, L. A. Johansson, and L. A. Coldren, “Integrated InP-InGaAsP tunable coupled ring optical bandpass filters with zero insertion loss,” Opt. Express 19(8), 7816–7826 (2011). [CrossRef] [PubMed]

8.

A. Meijerink, C. G. H. Roeloffzen, R. Meijerink, D. A. I. Leimeng Zhuang, M. J. Marpaung, M. Bentum, J. Burla, P. Verpoorte, A. Jorna, A. Hulzinga, and W. van Etten, “Novel ring resonator-based integrated photonic beamformer for broadband phased-array receive antennas-Part I: design and performance analysis,” J. Lightwave Technol. 28(1), 3–18 (2010). [CrossRef]

9.

C. G. H. L. Zhuang, A. Roeloffzen, M. Meijerink, D. Burla, A. Marpaung, M. Leinse, R. G. Hoekman, Heideman, and W. van Etten, “Novel ring resonator-based integrated photonic beamformer for broadband phased-array receive antennas-Part II: experimental prototype,” J. Lightwave Technol. 28(1), 19–31 (2010). [CrossRef]

10.

D. Marpaung, L. Zhuang, M. Burla, C. Roeloffzen, J. Verpoorte, H. Schippers, A. Hulzinga, P. Jorna, W. P. Beeker, A. Leinse, R. Heideman, B. Noharet, Q. Wang, B. Sanadgol, and R. Baggen, “Towards a broadband and squint-free Ku-band phased array antenna system for airborne satellite communications,” in Proceedings of the 5th European Conference on Antennas and Propagation (EuCAP) (2011), pp. 2774–2778 .

11.

C. G. H. Roeloffzen, A. Meijerink, L. Zhuang, D. A. I. Marpaung, R. G. Heideman, A. Leinse, M. Hoekman, and W. van Etten, “Integrated photonic beamformer employing continuously tunable ring resonator-based delays in CMOS-compatible LPCVD waveguide technology,” Proc. SPIE 7135, 71351K (2008). [CrossRef]

12.

F. Liu, T. Wang, L. Qiang, T. Ye, Z. Zhang, M. Qiu, and Y. Su, “Compact optical temporal differentiator based on silicon microring resonator,” Opt. Express 16(20), 15880–15886 (2008). [CrossRef] [PubMed]

13.

M. Ferrera, Y. Park, L. Razzari, B. E. Little, S. T. Chu, R. Morandotti, D. J. Moss, and J. Azaña, “On-chip CMOS-compatible all-optical integrator,” Nat Commun 1(3), 29 (2010). [CrossRef] [PubMed]

14.

M. H. Khan, H. Shen, Y. Xuan, L. Zhao, S. Xiao, D. E. Leaird, A. M. Weiner, and M. Qi, “Ultrabroad-bandwidth arbitrary radiofrequency waveform generation with a silicon photonic chip-based spectral shaper,” Nat. Photonics 4(2), 117–122 (2010). [CrossRef]

15.

H. Takahashi, “Planar lightwave circuit devices for optical communication: present and future,” Proc. SPIE 5246, 520–531 (2003). [CrossRef]

16.

Y. Li and C. Henry, “Silica-based optical integrated circuits,” IEEE Proc. Optoelectron. 143(5), 263–280 (1996). [CrossRef]

17.

R. Adar, M. Serbin, and V. Mizrahi, “Less than 1 dB per meter propagation loss of silica waveguides measured using a ring resonator,” J. Lightwave Technol. 12(8), 1369–1372 (1994). [CrossRef]

18.

M. John, Senior, Optical Fiber Communications Principles and Practice, 2nd ed. (Pearson Education, 1992).

19.

T. Kominato, Y. Hida, M. Itoh, H. Takahashi, S. Sohma, T. Kitoh, and Y. Hibino, “Extremely low-loss (0.3 dB/m) and long silica-based waveguides with large width and clothoid curve connection,” in Proceedings of ECOC (2004).

20.

M. Gnan, S. Thoms, D. S. Macintyre, R. M. De la Rue, and M. Sorel, “Fabrication of low-loss photonic wires in silicon-on-insulator using hydrogen silsesquioxane electron-beam resist,” Electron. Lett. 44(2), 115–116 (2008). [CrossRef]

21.

Y. Barbarin, X. J. M. Leijtens, E. A. J. M. Bente, C. M. Louzao, J. R. Kooiman, and M. K. Smit, “Extremely small AWG demultiplexer fabricated on InP by using a double-etch process,” IEEE Photon. Technol. Lett. 16(11), 2478–2480 (2004). [CrossRef]

22.

J. Cardenas, C. B. Poitras, J. T. Robinson, K. Preston, L. Chen, and M. Lipson, “Low loss etchless silicon photonic waveguides,” Opt. Express 17(6), 4752–4757 (2009). [CrossRef] [PubMed]

23.

M. Lysevych, H. H. Tan, F. Karouta, and C. Jagadish, “Single-step RIE fabrication process of low loss InP waveguide using CH4/H2 chemistry,” J. Electrochem. Soc. 158(3), H281–H284 (2011). [CrossRef]

24.

F. Morichetti, A. Melloni, M. Martinelli, R. É. G. Heideman, A. Leinse, D. H. Geuzebroek, and A. Borreman, “Box-shaped dielectric waveguides: a new concept in integrated optics?” J. Lightwave Technol. 25(9), 2579–2589 (2007). [CrossRef]

25.

J. F. Bauters, M. J. Heck, D. John, D. Dai, M. C. Tien, J. S. Barton, A. Leinse, R. G. Heideman, D. J. Blumenthal, and J. E. Bowers, “Ultra-low-loss high-aspect-ratio Si3N4 waveguides,” Opt. Express 19(4), 3163–3174 (2011). [CrossRef] [PubMed]

26.

L. Zhuang, Ring Resonator-Based Broadband Photonic Beam Former for Phased Array Antennas, PhD thesis (University of Twente, Enschede, The Netherlands, 2009).

27.

C. G. H. Roeloffzen, L. Zhuang, R. G. Heideman, A. Borreman, and W. van Etten, “Ring resonator-based tunable optical delay line in LPCVD waveguide technology,” in Proceedings Symposium IEEE/LEOS Benelux Chapter, 2005 (IEEE/LEOS, 2005), pp. 79–82.

28.

K. Oda, N. Takato, H. Toba, and K. Nosu, “A wide-band guided-wave periodic multi/demultiplexer with a ring resonator for optical FDM transmission system,” J. Lightwave Technol. 6(6), 1016–1023 (1988). [CrossRef]

29.

Z. Wang, S.-J. Chang, C.-Y. Ni, and Y. J. Chen, “A high-performance ultracompact optical interleaver based on double-ring assisted Mach-Zehnder interferometer,” IEEE Photon. Technol. Lett. 19(14), 1072–1074 (2007). [CrossRef]

OCIS Codes
(060.2360) Fiber optics and optical communications : Fiber optics links and subsystems
(060.5060) Fiber optics and optical communications : Phase modulation
(070.6020) Fourier optics and signal processing : Continuous optical signal processing
(130.3120) Integrated optics : Integrated optics devices
(350.4010) Other areas of optics : Microwaves
(060.5625) Fiber optics and optical communications : Radio frequency photonics

ToC Category:
Fiber Optics and Optical Communications

History
Original Manuscript: September 19, 2011
Revised Manuscript: October 13, 2011
Manuscript Accepted: October 17, 2011
Published: October 31, 2011

Citation
Leimeng Zhuang, David Marpaung, Maurizio Burla, Willem Beeker, Arne Leinse, and Chris Roeloffzen, "Low-loss, high-index-contrast Si3N4/SiO2 optical waveguides for optical delay lines in microwave photonics signal processing," Opt. Express 19, 23162-23170 (2011)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-19-23-23162


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. J. Capmany and D. Novak, “Microwave photonics combines two worlds,” Nat. Photonics1(6), 319–330 (2007). [CrossRef]
  2. A. Seeds, “Microwave photonics,” IEEE Trans. Microw. Theory Tech.50(3), 877–887 (2002). [CrossRef]
  3. J. Capmany, B. Ortega, D. Pastor, and S. Sales, “Discrete-Time Optical Processing of Microwave Signals,” J. Lightwave Technol.23(2), 702–723 (2005). [CrossRef]
  4. R. Minasian, “Photonic signal processing of microwave signals,” IEEE Trans. Microw. Theory Tech.54(2), 832–846 (2006). [CrossRef]
  5. N. N. Feng, P. Dong, D. Feng, W. Qian, H. Liang, D. C. Lee, J. B. Luff, A. Agarwal, T. Banwell, R. Menendez, P. Toliver, T. K. Woodward, and M. Asghari, “Thermally-efficient reconfigurable narrowband RF-photonic filter,” Opt. Express18(24), 24648–24653 (2010). [CrossRef] [PubMed]
  6. S. Ibrahim, N. K. Fontaine, S. S. Djordjevic, B. Guan, T. Su, S. Cheung, R. P. Scott, A. T. Pomerene, L. L. Seaford, C. M. Hill, S. Danziger, Z. Ding, K. Okamoto, and S. J. B. Yoo, “Demonstration of a fast-reconfigurable silicon CMOS optical lattice filter,” Opt. Express19(14), 13245–13256 (2011). [CrossRef] [PubMed]
  7. R. S. Guzzon, E. J. Norberg, J. S. Parker, L. A. Johansson, and L. A. Coldren, “Integrated InP-InGaAsP tunable coupled ring optical bandpass filters with zero insertion loss,” Opt. Express19(8), 7816–7826 (2011). [CrossRef] [PubMed]
  8. A. Meijerink, C. G. H. Roeloffzen, R. Meijerink, D. A. I. Leimeng Zhuang, M. J. Marpaung, M. Bentum, J. Burla, P. Verpoorte, A. Jorna, A. Hulzinga, and W. van Etten, “Novel ring resonator-based integrated photonic beamformer for broadband phased-array receive antennas-Part I: design and performance analysis,” J. Lightwave Technol.28(1), 3–18 (2010). [CrossRef]
  9. C. G. H. L. Zhuang, A. Roeloffzen, M. Meijerink, D. Burla, A. Marpaung, M. Leinse, R. G. Hoekman, Heideman, and W. van Etten, “Novel ring resonator-based integrated photonic beamformer for broadband phased-array receive antennas-Part II: experimental prototype,” J. Lightwave Technol.28(1), 19–31 (2010). [CrossRef]
  10. D. Marpaung, L. Zhuang, M. Burla, C. Roeloffzen, J. Verpoorte, H. Schippers, A. Hulzinga, P. Jorna, W. P. Beeker, A. Leinse, R. Heideman, B. Noharet, Q. Wang, B. Sanadgol, and R. Baggen, “Towards a broadband and squint-free Ku-band phased array antenna system for airborne satellite communications,” in Proceedings of the 5th European Conference on Antennas and Propagation (EuCAP) (2011), pp. 2774–2778 .
  11. C. G. H. Roeloffzen, A. Meijerink, L. Zhuang, D. A. I. Marpaung, R. G. Heideman, A. Leinse, M. Hoekman, and W. van Etten, “Integrated photonic beamformer employing continuously tunable ring resonator-based delays in CMOS-compatible LPCVD waveguide technology,” Proc. SPIE7135, 71351K (2008). [CrossRef]
  12. F. Liu, T. Wang, L. Qiang, T. Ye, Z. Zhang, M. Qiu, and Y. Su, “Compact optical temporal differentiator based on silicon microring resonator,” Opt. Express16(20), 15880–15886 (2008). [CrossRef] [PubMed]
  13. M. Ferrera, Y. Park, L. Razzari, B. E. Little, S. T. Chu, R. Morandotti, D. J. Moss, and J. Azaña, “On-chip CMOS-compatible all-optical integrator,” Nat Commun1(3), 29 (2010). [CrossRef] [PubMed]
  14. M. H. Khan, H. Shen, Y. Xuan, L. Zhao, S. Xiao, D. E. Leaird, A. M. Weiner, and M. Qi, “Ultrabroad-bandwidth arbitrary radiofrequency waveform generation with a silicon photonic chip-based spectral shaper,” Nat. Photonics4(2), 117–122 (2010). [CrossRef]
  15. H. Takahashi, “Planar lightwave circuit devices for optical communication: present and future,” Proc. SPIE5246, 520–531 (2003). [CrossRef]
  16. Y. Li and C. Henry, “Silica-based optical integrated circuits,” IEEE Proc. Optoelectron.143(5), 263–280 (1996). [CrossRef]
  17. R. Adar, M. Serbin, and V. Mizrahi, “Less than 1 dB per meter propagation loss of silica waveguides measured using a ring resonator,” J. Lightwave Technol.12(8), 1369–1372 (1994). [CrossRef]
  18. M. John, Senior, Optical Fiber Communications Principles and Practice, 2nd ed. (Pearson Education, 1992).
  19. T. Kominato, Y. Hida, M. Itoh, H. Takahashi, S. Sohma, T. Kitoh, and Y. Hibino, “Extremely low-loss (0.3 dB/m) and long silica-based waveguides with large width and clothoid curve connection,” in Proceedings of ECOC (2004).
  20. M. Gnan, S. Thoms, D. S. Macintyre, R. M. De la Rue, and M. Sorel, “Fabrication of low-loss photonic wires in silicon-on-insulator using hydrogen silsesquioxane electron-beam resist,” Electron. Lett.44(2), 115–116 (2008). [CrossRef]
  21. Y. Barbarin, X. J. M. Leijtens, E. A. J. M. Bente, C. M. Louzao, J. R. Kooiman, and M. K. Smit, “Extremely small AWG demultiplexer fabricated on InP by using a double-etch process,” IEEE Photon. Technol. Lett.16(11), 2478–2480 (2004). [CrossRef]
  22. J. Cardenas, C. B. Poitras, J. T. Robinson, K. Preston, L. Chen, and M. Lipson, “Low loss etchless silicon photonic waveguides,” Opt. Express17(6), 4752–4757 (2009). [CrossRef] [PubMed]
  23. M. Lysevych, H. H. Tan, F. Karouta, and C. Jagadish, “Single-step RIE fabrication process of low loss InP waveguide using CH4/H2 chemistry,” J. Electrochem. Soc.158(3), H281–H284 (2011). [CrossRef]
  24. F. Morichetti, A. Melloni, M. Martinelli, R. É. G. Heideman, A. Leinse, D. H. Geuzebroek, and A. Borreman, “Box-shaped dielectric waveguides: a new concept in integrated optics?” J. Lightwave Technol.25(9), 2579–2589 (2007). [CrossRef]
  25. J. F. Bauters, M. J. Heck, D. John, D. Dai, M. C. Tien, J. S. Barton, A. Leinse, R. G. Heideman, D. J. Blumenthal, and J. E. Bowers, “Ultra-low-loss high-aspect-ratio Si3N4 waveguides,” Opt. Express19(4), 3163–3174 (2011). [CrossRef] [PubMed]
  26. L. Zhuang, Ring Resonator-Based Broadband Photonic Beam Former for Phased Array Antennas, PhD thesis (University of Twente, Enschede, The Netherlands, 2009).
  27. C. G. H. Roeloffzen, L. Zhuang, R. G. Heideman, A. Borreman, and W. van Etten, “Ring resonator-based tunable optical delay line in LPCVD waveguide technology,” in Proceedings Symposium IEEE/LEOS Benelux Chapter, 2005 (IEEE/LEOS, 2005), pp. 79–82.
  28. K. Oda, N. Takato, H. Toba, and K. Nosu, “A wide-band guided-wave periodic multi/demultiplexer with a ring resonator for optical FDM transmission system,” J. Lightwave Technol.6(6), 1016–1023 (1988). [CrossRef]
  29. Z. Wang, S.-J. Chang, C.-Y. Ni, and Y. J. Chen, “A high-performance ultracompact optical interleaver based on double-ring assisted Mach-Zehnder interferometer,” IEEE Photon. Technol. Lett.19(14), 1072–1074 (2007). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited