OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 20, Iss. 12 — Jun. 4, 2012
  • pp: 13551–13559
« Show journal navigation

Subsurface damage distribution characterization of ground surfaces using Abbott–Firestone curves

Raynald Laheurte, Philippe Darnis, Nathalie Darbois, Olivier Cahuc, and Jérôme Neauport  »View Author Affiliations


Optics Express, Vol. 20, Issue 12, pp. 13551-13559 (2012)
http://dx.doi.org/10.1364/OE.20.013551


View Full Text Article

Acrobat PDF (822 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

Measurement of subsurface damage (SSD) induced by grinding process is of major interest in the development of high laser damage fused silica optical components manufacturing processes. Most SSD measurements methods give only access to the peak to peak value. We herein report on the benefit of using Abbott–Firestone curves to get an insight of the SSD distribution inside the optical material. We evidence on various diamond wheel ground fused silica substrates that such an approach is complementary to a classical SSD peak to peak measurement and bring useful information to optimize a grinding process.

© 2012 OSA

1. Introduction

The 351nm wavelength ns-pulse laser damage of fused silica optics is one of the major limitations of laser facilities such as LMJ (Laser Megajoule) and NIF (National Ignition Facility). Indeed the high fluences, which are subject optics, can cause damage which can grow under subsequent laser shots and thus drastically limit the optics lifetime. Early works have shown that defects present at the interface of fused silica such mechanical subsurface damage [1

1. M. D. Feit and A. M. Rubenchik, “Influence of subsurface cracks on laser induced surface damage,” Proc. SPIE 5273, 264–272 (2004). [CrossRef]

] can be precursors of laser damage. For example, laser induced damage tests performed on Berkovitch type indentations at the surface of a fused silica sample showed that they could trigger damage at a fluence close to 10J/cm2, similar to what is observed on full scale fused silica polished optics [2

2. M. A. Josse, H. Bercegol, R. Courchinoux, T. Donval, L. Lamaignère, B. Pussacq, and J. L. Rullier, “Study of the evolution of mechanical defects on silica samples under laser irradiation at 355 nm,” Proc. SPIE 6403, 64030E, 64030E-7 (2006). [CrossRef]

]. Manufacturing steps of optics, from grinding to polishing, are known to be major contributors to the creation of such mechanical flaws. During grinding step, the diamond grains, present in diamond tools, act as indenters [3

3. J. Lambropoulos, “Micromechanics of material-removal mechanisms from brittle surfaces,” LLE Review 74, 131–138 (1998).

] that embrittle locally the material. Based on these considerations the reduction of SSD during the polishing process is of peculiar importance to produce high damage threshold optics.

Knowing the depth of SSD provides essential information to remove these fractures during the various manufacturing stages, and development of fusion class laser facilities has put new focus on this topic. The characterization of SSD is the subject of many studies. The methods used are most often destructive, but some non-destructive methods can also be used. The principle consist generally in achieving a local wear (e.g. ball dimpling [4

4. Y. Zhou, D. Funkenbusch, D. J. Quesnel, D. Golini, and A. Lindquist, “Effect of etching and imaging mode on the measurement of subsurface damage in microground optical glasses,” J. Am. Ceram. Soc. 77(12), 3277–3280 (1994). [CrossRef]

] or MRF dimpling [5

5. J. A. Randi, J. C. Lambropoulos, and S. D. Jacobs, “Subsurface damage in some single crystalline optical materials,” Appl. Opt. 44(12), 2241–2249 (2005). [CrossRef] [PubMed]

]) or global polishing (e.g. taper polishing or MRF taper) [6

6. T. Suratwala, L. Wong, P. Miller, M. D. Feit, J. Menapace, R. Steele, P. Davis, and D. Walmer, “Sub-surface mechanical damage distributions during grinding of fused silica,” J. Non-Cryst. Solids 352(52-54), 5601–5617 (2006). [CrossRef]

] on the workpiece to reveal the micro-cracks whose depth can then be measured by conventional microscopic observation. Such characterizations are generally used to define an empirical relationship between surface roughness (Rt) and depth of defects under surface. Preston [7

7. F. W. Preston, “The structure of abraded glass surfaces,” Trans. Opt. Soc. 23(3), 141–164 (1922). [CrossRef]

] reported that the depth of subsurface defects is three times higher than the Peak-to-Valley roughness. Recent studies have shown a good correlation between the maximum SSD depth and the undulation of the surface (4th order moment) [6

6. T. Suratwala, L. Wong, P. Miller, M. D. Feit, J. Menapace, R. Steele, P. Davis, and D. Walmer, “Sub-surface mechanical damage distributions during grinding of fused silica,” J. Non-Cryst. Solids 352(52-54), 5601–5617 (2006). [CrossRef]

]. Characterization by chemical method [8

8. J. Neauport, C. Ambard, P. Cormont, N. Darbois, J. Destribats, C. Luitot, and O. Rondeau, “Subsurface damage measurement of ground fused silica parts by HF etching techniques,” Opt. Express 17(22), 20448–20456 (2009). [CrossRef] [PubMed]

] can also be performed, by following, in successive etchings in a HF bath, either the evolution of surface roughness peak to peak Rt or the decrease of contaminants. Non-destructive methods (whitelight, tomography, confocal fluorescence microscopy [9

9. J. Neauport, P. Cormont, P. Legros, C. Ambard, and J. Destribats, “Imaging subsurface damage of grinded fused silica optics by confocal fluorescence microscopy,” Opt. Express 17(5), 3543–3554 (2009). [CrossRef] [PubMed]

] …) can also be performed by probing the interface of the sample without altering the surface of fused silica. However these non-destructive methods only provide access to a localized area and have tends to be significantly inaccurate. Whatever the method, destructive or not, they only give access to the SSD's depth and no information is given on the spatial distribution of the fractures.

In the following study, we investigate the Abbott–Firestone curve [10

10. E. J. Abbott and F. A. Firestone, “Specifying surface quality: a method based on accurate measurement and comparison,” Mech. Eng. 55, 569–572 (1933).

] or bearing area curve, which describes the surface texture of an object, as an additional indicator to the quality of the glass interface. These Abbott–Firestone parameters give access to the average depth of streaks crisscrossing the surface and to the relative importance of deep fractures existing under the surface.

Analysis of the Abbott–Firestone curves of ground and etched samples provide access not only to the peak to peak value of the SSD but also bring additional information on the distribution of subsurface damage within this peak to peak value. Information on the overall distribution of damage underlying the surface but also on the proportion of damaged areas are obtained. Such information could, for optimized machine parameters, warn us on the need to revive a grinding wheel, alert us on a non-optimal lubrication. Abbott–Firestone curves, as detailed in this paper, have also the advantage to be quite easy to obtain being based on direct use of data provided by roughness measurements when e.g. compared to iterative microscopic observation techniques used to obtain a cumulative crack obscuration as a function of depth into the glass surface [6

6. T. Suratwala, L. Wong, P. Miller, M. D. Feit, J. Menapace, R. Steele, P. Davis, and D. Walmer, “Sub-surface mechanical damage distributions during grinding of fused silica,” J. Non-Cryst. Solids 352(52-54), 5601–5617 (2006). [CrossRef]

].

In the first section, the principle of the Abbott–Firestone curve is detailed and illustrated by some examples. Sample preparation and associated characterization are briefly described in section 3. Results are then presented and discussed in section 4 to then bring our conclusions.

2. Abbott–Firestone curves

The Abbott–Firestone curves are currently used to characterize surface texture. The characterization of friction or also wear of surfaces is improved using the parameters calculated with Abbott–Firestone curves [11

11. M. Bigerelle and A. Iost, “A numerical method to calculate the Abbott parameters: A wear application,” Tribol. Int. 40(9), 1319–1334 (2007). [CrossRef]

] since they give access to both size and proportion of the peaks and valleys of a given surface [12

12. A. Brient, M. Brissot, T. Rouxel, and J. C. Sangleboeuf, “Influence of grinding parameters on glass workpieces surface finish using response surface methodology,” J. Manuf. Sci. Eng. 133(4), 044501 (2011). [CrossRef]

]. Consequently such a characterization method appears to be particularly well suited when ones want to define the proportion of the valleys on a surface such as it's the case for glass surfaces full of subsurface cracks.

Abbott–Firestone parameters are obtained by computing the cumulative probability density function of the surface profile's height by integrating the profile trace. Using the normalization ISO 13565 [13

13. AFNOR, “NF EN ISO 13565,” in Geometrical Product Specifications (GPS)–Surface texture: Profile method; Surfaces having stratified functional properties, (Paris, 1998).

] Abbott–Firestone parameters are defined (Table 1

Table 1. Abbott–Firestone Parameters

table-icon
View This Table
| View All Tables
and Fig. 1
Fig. 1 Abbott–Firestone curve. (a) measured roughness profile trace. (b) the cumulative probability density function of the profile trace analysis allows the computation of Abbott–Firestone parameters.
) as follows.

If Rk represents the running surface on which effort are applied, Rpk is the reduced peak height that will quickly wear during process and Rvk is the reduced valley depth that will tend to subsist at the end of the process and lead to SSD. Mr1 and Mr2 are the relative proportion of this peak and valley (if the complementary value of Mr2 is taking into account) areas in the profile.

An example of an Abbott–Firestone curve obtained on a ground glass surface, without etching, is presented in Fig. 2
Fig. 2 Typical Abbott–Firestone curve for fused silica sample. (a) measured roughness profile trace. (b) the cumulative probability density function of the profile trace analysis allows the computation of Abbott–Firestone parameters.
.

For typical surface manufactured with grinding process, the Abbott–Firestone curve (Fig. 2) exhibits an important difference between the Rpk and Rvk parameters. This difference is characteristic of the surface's topology where the valleys are marked compared to the peaks. The parameter Mr2 can be interpreted as the density of the valleys of the surface. Indeed, the higher the value of Mr2 the lower the valleys density will be.

3. Experimentals

3.1 Sample surface preparation

Square-shaped fused silica glass (HOQ from Heraeus) samples (100x100mm2 x 10mm thick) were used for this study. Roughing was first performed on each sample in order to have the same reference state. Material removal of the first grinding step was then chosen to guarantee a complete removal of residual SSD from the preceding roughing step.

Two sample batches (labeled as Batch A and B) were manufactured on an OPTOTECH SMP500-2C grinder. The samples were grounded using various parameters summarized in Table 2

Table 2. Summary of Operating Conditions for Fused Silica Samples Batches A-B

table-icon
View This Table
| View All Tables
. The samples were ground by blocking the rotation axis of the workpiece table and by translating the grinding wheel in order to be able to only observe the effect of the wheel on the material. Let's outline that this configuration is more damaging for the surface that the usual one for which the two rotations (sample and spindle) are performed simultaneously. Batch A (respectively B), refers to the milling operation using a D126 (respectively intermediate D64) metallic bond diamond wheel. Varying processing conditions were tested with different cutting speed, feed and depth of cut; three values were considered for each parameter. Some samples have been used for both configurations batches A and B.

3.2 Sample characterization

To characterize the precision grinding operation, the surface roughness for each of the ground surfaces was measured by MITUTOYO (SJ-201) contact stylus profilometer, equipped with an inductive probe with 2μm radius and 90° angle. According to the normalized procedure [13

13. AFNOR, “NF EN ISO 13565,” in Geometrical Product Specifications (GPS)–Surface texture: Profile method; Surfaces having stratified functional properties, (Paris, 1998).

], scans of 4mm length were performed, on 16 areas uniformly distributed on the surface of each sample [8

8. J. Neauport, C. Ambard, P. Cormont, N. Darbois, J. Destribats, C. Luitot, and O. Rondeau, “Subsurface damage measurement of ground fused silica parts by HF etching techniques,” Opt. Express 17(22), 20448–20456 (2009). [CrossRef] [PubMed]

]. For each sample, the Rt reported in Table 2 is the maximum value obtained on all 16 scans. The roughness Ra and the Abbott–Firestone parameters deduced from the profile measurements are also shown on Table 2. SSD depth was also controlled by means of acid etching; it consists in following the evolution of surface roughness Rt during successive hydrofluoric acid (HF) etching. Rt is measured after each etching step and the maximal value of Rt among the whole set of measurements is equal to the SSD depth as described elsewhere [8

8. J. Neauport, C. Ambard, P. Cormont, N. Darbois, J. Destribats, C. Luitot, and O. Rondeau, “Subsurface damage measurement of ground fused silica parts by HF etching techniques,” Opt. Express 17(22), 20448–20456 (2009). [CrossRef] [PubMed]

]. The surface roughness δ defined by Suratwala [6

6. T. Suratwala, L. Wong, P. Miller, M. D. Feit, J. Menapace, R. Steele, P. Davis, and D. Walmer, “Sub-surface mechanical damage distributions during grinding of fused silica,” J. Non-Cryst. Solids 352(52-54), 5601–5617 (2006). [CrossRef]

] is also calculated and reported in Table 3

Table 3. Roughness, Abbott–Firestone Parameters and SSD Results

table-icon
View This Table
| View All Tables
.

4. Results and discussions

The evolutions of parameters proposed in Table 4 are presented in the curves hereafter. Let's outline that following figures will be presented with the test number in abscissa. Points are plotted in the same order than presented on Table 2. Such a representation is done to compare the relative evolution of the different indicators for the different diamond wheels (batches A and B) and cutting conditions.

The results of kRt and kδ indicators presented on the Fig. 3
Fig. 3 Rt (a) and δ (b) bibliographic indicators evolution [6].
appear to be quite scattered and far from the results of the Suratwala who established values of kRt = 9.1 and kδ = 49 [6

6. T. Suratwala, L. Wong, P. Miller, M. D. Feit, J. Menapace, R. Steele, P. Davis, and D. Walmer, “Sub-surface mechanical damage distributions during grinding of fused silica,” J. Non-Cryst. Solids 352(52-54), 5601–5617 (2006). [CrossRef]

]. Such behavior has already been demonstrated in other studies [8

8. J. Neauport, C. Ambard, P. Cormont, N. Darbois, J. Destribats, C. Luitot, and O. Rondeau, “Subsurface damage measurement of ground fused silica parts by HF etching techniques,” Opt. Express 17(22), 20448–20456 (2009). [CrossRef] [PubMed]

]. For the chosen configuration of machining and for two different types of wheel, it can be concluded that these kRt and kδ indicators are dependent on the process, the type of tool, the kinematic conditions …

In the Fig. 5
Fig. 5 Mr1 (a) and Mr2 (b) Abbott–Firestone indicators evolution.
, the parameters involving Mr1 and Mr2, respectively, show that a relationship between peaks and valleys densities and the depth of SSD can be expressed. The Mr1 and Mr2 parameters appear to be relatively independent of kinematic conditions. However, the results show a strong dependence on the size and density (D126 or D64) of the wheel.

Considering typical roughness profiles such as obtained on a diamond ground glass surfaces (Fig. 2), the more pertinent parameters characterizing both damage and topology of the such surfaces are both the depth of SSD and the Mr2 Abbott–Firestone parameter.

It is also observed (Fig. 6
Fig. 6 SSD (a) and Mr2 (b) Abbott–Firestone parameter evolution.
) that whatever the cutting conditions (spindle speed, feed rate), the wheel with the smaller particle size generates the lowest SSD's depth and upper valleys density. In our experimental study the influence of the particle density, for a given particle size, has not been studied. However, this parameter could affect the density of SSD; but this remains to be confirmed by additional tests.

Thus, the tests conducted in this study allow one hand to show that the indicators currently used are too dependent on experimental conditions and also to provide opportunities for the development of new indicators more relevant through the use of Abbott–Firestone parameters.

5. Conclusion and prospects

Characterization of the SSD is a crucial step to determine optimal process parameters to manufacture laser optics. We investigated the relative evolution of various surface profile indicators on a variety of diamond ground surfaces manufactured with different cutting conditions and diamond wheels. It is evidenced that the parameters usually used to estimate SSD from a roughness profile such as roughness peak to peak Rt or 4th order moment δ are highly dependent on manufacturing conditions. On the contrary, kMr2, based on Abbott–Firestone curves seems to be more representative of SSD since it appears to stay constant when changing manufacturing parameters. We also evidenced a significant influence of the grinding parameters (grain size, grain density). This behavior shall be further analyzed by additional experiments.

Acknowledgments

This work is supported by the Conseil Régional d’Aquitaine and is performed in the framework of the EFESO project.

References and links

1.

M. D. Feit and A. M. Rubenchik, “Influence of subsurface cracks on laser induced surface damage,” Proc. SPIE 5273, 264–272 (2004). [CrossRef]

2.

M. A. Josse, H. Bercegol, R. Courchinoux, T. Donval, L. Lamaignère, B. Pussacq, and J. L. Rullier, “Study of the evolution of mechanical defects on silica samples under laser irradiation at 355 nm,” Proc. SPIE 6403, 64030E, 64030E-7 (2006). [CrossRef]

3.

J. Lambropoulos, “Micromechanics of material-removal mechanisms from brittle surfaces,” LLE Review 74, 131–138 (1998).

4.

Y. Zhou, D. Funkenbusch, D. J. Quesnel, D. Golini, and A. Lindquist, “Effect of etching and imaging mode on the measurement of subsurface damage in microground optical glasses,” J. Am. Ceram. Soc. 77(12), 3277–3280 (1994). [CrossRef]

5.

J. A. Randi, J. C. Lambropoulos, and S. D. Jacobs, “Subsurface damage in some single crystalline optical materials,” Appl. Opt. 44(12), 2241–2249 (2005). [CrossRef] [PubMed]

6.

T. Suratwala, L. Wong, P. Miller, M. D. Feit, J. Menapace, R. Steele, P. Davis, and D. Walmer, “Sub-surface mechanical damage distributions during grinding of fused silica,” J. Non-Cryst. Solids 352(52-54), 5601–5617 (2006). [CrossRef]

7.

F. W. Preston, “The structure of abraded glass surfaces,” Trans. Opt. Soc. 23(3), 141–164 (1922). [CrossRef]

8.

J. Neauport, C. Ambard, P. Cormont, N. Darbois, J. Destribats, C. Luitot, and O. Rondeau, “Subsurface damage measurement of ground fused silica parts by HF etching techniques,” Opt. Express 17(22), 20448–20456 (2009). [CrossRef] [PubMed]

9.

J. Neauport, P. Cormont, P. Legros, C. Ambard, and J. Destribats, “Imaging subsurface damage of grinded fused silica optics by confocal fluorescence microscopy,” Opt. Express 17(5), 3543–3554 (2009). [CrossRef] [PubMed]

10.

E. J. Abbott and F. A. Firestone, “Specifying surface quality: a method based on accurate measurement and comparison,” Mech. Eng. 55, 569–572 (1933).

11.

M. Bigerelle and A. Iost, “A numerical method to calculate the Abbott parameters: A wear application,” Tribol. Int. 40(9), 1319–1334 (2007). [CrossRef]

12.

A. Brient, M. Brissot, T. Rouxel, and J. C. Sangleboeuf, “Influence of grinding parameters on glass workpieces surface finish using response surface methodology,” J. Manuf. Sci. Eng. 133(4), 044501 (2011). [CrossRef]

13.

AFNOR, “NF EN ISO 13565,” in Geometrical Product Specifications (GPS)–Surface texture: Profile method; Surfaces having stratified functional properties, (Paris, 1998).

OCIS Codes
(140.3330) Lasers and laser optics : Laser damage
(220.1920) Optical design and fabrication : Diamond machining

ToC Category:
Lasers and Laser Optics

History
Original Manuscript: March 16, 2012
Revised Manuscript: April 20, 2012
Manuscript Accepted: April 30, 2012
Published: June 1, 2012

Citation
Raynald Laheurte, Philippe Darnis, Nathalie Darbois, Olivier Cahuc, and Jérôme Neauport, "Subsurface damage distribution characterization of ground surfaces using Abbott–Firestone curves," Opt. Express 20, 13551-13559 (2012)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-20-12-13551


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. M. D. Feit and A. M. Rubenchik, “Influence of subsurface cracks on laser induced surface damage,” Proc. SPIE5273, 264–272 (2004). [CrossRef]
  2. M. A. Josse, H. Bercegol, R. Courchinoux, T. Donval, L. Lamaignère, B. Pussacq, and J. L. Rullier, “Study of the evolution of mechanical defects on silica samples under laser irradiation at 355 nm,” Proc. SPIE6403, 64030E, 64030E-7 (2006). [CrossRef]
  3. J. Lambropoulos, “Micromechanics of material-removal mechanisms from brittle surfaces,” LLE Review74, 131–138 (1998).
  4. Y. Zhou, D. Funkenbusch, D. J. Quesnel, D. Golini, and A. Lindquist, “Effect of etching and imaging mode on the measurement of subsurface damage in microground optical glasses,” J. Am. Ceram. Soc.77(12), 3277–3280 (1994). [CrossRef]
  5. J. A. Randi, J. C. Lambropoulos, and S. D. Jacobs, “Subsurface damage in some single crystalline optical materials,” Appl. Opt.44(12), 2241–2249 (2005). [CrossRef] [PubMed]
  6. T. Suratwala, L. Wong, P. Miller, M. D. Feit, J. Menapace, R. Steele, P. Davis, and D. Walmer, “Sub-surface mechanical damage distributions during grinding of fused silica,” J. Non-Cryst. Solids352(52-54), 5601–5617 (2006). [CrossRef]
  7. F. W. Preston, “The structure of abraded glass surfaces,” Trans. Opt. Soc.23(3), 141–164 (1922). [CrossRef]
  8. J. Neauport, C. Ambard, P. Cormont, N. Darbois, J. Destribats, C. Luitot, and O. Rondeau, “Subsurface damage measurement of ground fused silica parts by HF etching techniques,” Opt. Express17(22), 20448–20456 (2009). [CrossRef] [PubMed]
  9. J. Neauport, P. Cormont, P. Legros, C. Ambard, and J. Destribats, “Imaging subsurface damage of grinded fused silica optics by confocal fluorescence microscopy,” Opt. Express17(5), 3543–3554 (2009). [CrossRef] [PubMed]
  10. E. J. Abbott and F. A. Firestone, “Specifying surface quality: a method based on accurate measurement and comparison,” Mech. Eng.55, 569–572 (1933).
  11. M. Bigerelle and A. Iost, “A numerical method to calculate the Abbott parameters: A wear application,” Tribol. Int.40(9), 1319–1334 (2007). [CrossRef]
  12. A. Brient, M. Brissot, T. Rouxel, and J. C. Sangleboeuf, “Influence of grinding parameters on glass workpieces surface finish using response surface methodology,” J. Manuf. Sci. Eng.133(4), 044501 (2011). [CrossRef]
  13. AFNOR, “NF EN ISO 13565,” in Geometrical Product Specifications (GPS)–Surface texture: Profile method; Surfaces having stratified functional properties, (Paris, 1998).

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited