OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 20, Iss. 13 — Jun. 18, 2012
  • pp: 14302–14307
« Show journal navigation

Reception of mode-division multiplexed superchannel via few-mode compatible optical add/drop multiplexer

Xi Chen, An Li, Jia Ye, Abdullah Al Amin, and William Shieh  »View Author Affiliations


Optics Express, Vol. 20, Issue 13, pp. 14302-14307 (2012)
http://dx.doi.org/10.1364/OE.20.014302


View Full Text Article

Acrobat PDF (1321 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We report the first few-mode compatible optical add/drop multiplexer (OADM) that enables add/drop functionality for mode division multiplexed (MDM) superchannels. The OADM is comprised of two cascaded free-space thin-film filters with 5° incident angle. The transmission of MDM superchannel CO-OFDM signals via the OADM is investigated. The experimental result shows that the OSNR penalties for add, drop and through ports are 2.6, 2.4, 0.7 dB, respectively for 3x318 Gb/s superchannels.

© 2012 OSA

1. Introduction

The Shannon capacity limit of single-mode fiber (SMF) systems in the presence of fiber nonlinearity has been extensively studied in the last decade [1

1. P. P. Mitra and J. B. Stark, “Nonlinear limits to the information capacity of optical fibre communications,” Nature 411(6841), 1027–1030 (2001). [CrossRef] [PubMed]

4

4. W. Shieh and X. Chen, “Information spectral efficiency and launch power density limits due to fiber nonlinearity for coherent optical OFDM systems,” IEEE Photon. J. 3(2), 158–173 (2011). [CrossRef]

]. This capacity has been quickly approached by the recent demonstration within some practical engineering margin [5

5. D. Qian, M. F. Huang, E. Ip, Y. K. Huang, Y. Shao, J. Hu, and T. Wang, “101.7-Tb/s (370 x 294-Gb/s) PDM-128QAM-OFDM transmission over 3 x 55-km SSMF using pilot-based phase noise mitigation,” Optical Fiber Communication Conference (OFC), 2011, PDPB5.

]. It is impossible to enjoy the same dramatic capacity improvement in the future as in the past two decades if we continue to stay with the SMF platform. Therefore, the spatial-division multiplexing (SDM) has been explored recently to overcome the capacity barrier [6

6. J. Sakaguchi, Y. Awaji, N. Wada, A. Kanno, T. Kawanishi, T. Hayashi, T. Taru, T. Kobayashi, and M. Watanabe, “109-Tb/s (7×97×172-Gb/s SDM/WDM/PDM) QPSK transmission through 16.8-km homogeneous multi-core fiber,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB6.

13

13. E. Ip, B. Neng, Y. K. Huang, E. Mateo, F. Yaman, M. J. Li, S. Bickham, S. Ten, J. Linares, C. Montero, V. Moreno, X. Prieto, V. Tse, K. M. Chung, A. Lau, H. Y. Tam, C. Lu, Y. H. Luo, G. D. Peng, and G. Li, “88×3×112-Gb/s WDM transmission over 50 km of three-mode fiber with inline few-mode fiber amplifier”, in European Conference and Exposition on Optical Communications (ECOC), Geneva, Switzerland, 2011, Th.13.C.2.

]. There are a few techniques available at the moment for SDM, including multi-core fiber (MCF) [6

6. J. Sakaguchi, Y. Awaji, N. Wada, A. Kanno, T. Kawanishi, T. Hayashi, T. Taru, T. Kobayashi, and M. Watanabe, “109-Tb/s (7×97×172-Gb/s SDM/WDM/PDM) QPSK transmission through 16.8-km homogeneous multi-core fiber,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB6.

8

8. B. Zhu, T. Taunay, M. Fishteyn, X. Liu, S. Chandrasekhar, M. Yan, J. Fini, E. Monberg, and F. Dimarcello, “Space-, wavelength-, polarization-division multiplexed transmission of 56-Tb/s over a 76.8-km seven-core fiber,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB.7.

] and few-mode fiber (FMF) [9

9. N. Hanzawa, K. Saitoh, T. Sakamoto, T. Matsui, S. Tomita, and M. Koshiba, “Demonstration of mode-division multiplexing transmission over 10 km two-mode fiber with mode coupler,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, OWA4.

13

13. E. Ip, B. Neng, Y. K. Huang, E. Mateo, F. Yaman, M. J. Li, S. Bickham, S. Ten, J. Linares, C. Montero, V. Moreno, X. Prieto, V. Tse, K. M. Chung, A. Lau, H. Y. Tam, C. Lu, Y. H. Luo, G. D. Peng, and G. Li, “88×3×112-Gb/s WDM transmission over 50 km of three-mode fiber with inline few-mode fiber amplifier”, in European Conference and Exposition on Optical Communications (ECOC), Geneva, Switzerland, 2011, Th.13.C.2.

]. During the last few years, there has been impressive progress in the research of MCF and FMF transmission. However, there have also been some intriguing questions regarding comparison between MCF and FMF systems.

This paper touches upon an important perspective of different implementations in OADM for FMF- and MCF-based systems. In MCF-based systems, the optical signals in different cores are transmitted independently. Therefore, the system complexity, more specifically the number of OADMs, are multiplied by the number of cores. However, in FMF-based systems, there exists a great opportunity to simplify the system design. Figure 1
Fig.1 Illustration of few-mode compatible ROADM in few-mode fiber based optical networks. MDM: Mode division multiplexing/multiplexed, Mux: Multiplexer, DeMux: De-Multiplexer, FMF: Few-mode fiber.
shows the future high-capacity few-mode fiber networks where the wavelength channels containing all the modes are routed as one entity which is subsequently optically added/dropped, and amplified without mode-demultiplexing/multiplexing during transmission. We call this wavelength channel containing few-mode tributaries the mode-division multiplexed (MDM) superchannel. An analogy can be drawn between such a FMF-based system and polarization-multiplexed (PM) system where the two polarizations are not separately processed during the transmission, which greatly simplifies the system design while doubling the system capacity. In this paper, we show for the first time the feasibility of FMF-compatible OADM, which is an important first step towards FMF-compatible ROADMs. We demonstrate successful reception of CO-OFDM signal passing through a dual-LP11 mode FMF-based OADM. We found that the power penalties for add, drop and through ports are 2.6, 2.4, 0.7 dB, respectively for 3x318 Gb/s OFDM signals.

2. OADM architecture

The architecture of the FMF compatible OADM can be similar to their SMF counterparts. We consider that mode dependence of beam divergence angle in a FMF to be small for a practical implementation of OADM with free-space components. This argument is true since the beam divergence Θcan be calculated as Θ=Dm/f, where Dm is the mode field diameter (MFD) and f is the focal length of collimators. We use collimators of 11-mm focal length, and the MFDs are 11.0 µm and 11.3 µm for LP01 mode and LP11 mode respectively. The above parameters give less than 0.06 degree divergence, which makes the transmission characteristics insensitive to different modes. Such free-space optics based OADMs can be miniaturized and the number of input/output ports can be scaled up by using well-established technologies such as MEMS and LCOS [17

17. S. Tibuleac and M. Filer, “Transmission impairments in DWDM networks with reconfigurable optical add-drop multiplexers,” J. Lightwave Technol. 28(4), 557–598 (2010). [CrossRef]

]. In this work, we design and build a two-mode compatible free-space OADM using collimators and a pair of thin film filters (TFF). Figure 2
Fig. 2 Schematic diagram of the two-mode OADM.
shows the OADM architecture. The TFFs act as a band-pass filter in transmission mode and as a notch-filter in the reflection mode. We use double reflection in order to sufficiently suppress the drop channel in output, which would otherwise serve as in-band crosstalk for the add channel. We tilt the TFFs by 5° in order to achieve lateral separation of the in/add and drop/through ports in the double reflection configuration. The 5° tilt launch also prevents any parasitic reflection from the drop or add ports due to accumuled multiple reflections. The free-space beam diameter is 2 mm.

In order to characterize the few-mode compatible OADM, we conduct measurement for the OADM using both LP11 modes and LP01 mode. First, we attach two-mode fiber (TMF) to the four ports (in, add, through, and drop) and use LP11 mode to measure the transmission characteristics. The LP11 mode (LP11a or LP11b) is generated by a conventional SMF transmitter, a long-period fiber grating (LPFG)-based mode converter (MC) [10

10. A. Li, A. Al Amin, X. Chen, and W. Shieh, “ Reception of mode and polarization multiplexed 107-Gb/s CO-OFDM signal over a two-mode fiber” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB8.

,18

18. A. Al Amin, A. Li, S. Chen, X. Chen, G. Gao, and W. Shieh, “Dual-LP11 mode 4×4 MIMO-OFDM transmission over a two-mode fiber,” Opt. Express 19(17), 16672–16679 (2011). [CrossRef] [PubMed]

], and a mode stripper (MS). The generated LP11 mode is fed through a collimator lens, a prism, the other collimator lens, and then coupled to a TMF fiber which is connected to an OADM. At the through and the drop ports of the OADM, the TMF fiber is directly attached to a multimode OSA to measure the spectrum. The transmission characteristics of the two LP11 modes measured by the OSA is shown in Fig. 3(a)
Fig. 3 (a) Measured transmission characteristics of the OADM based on TMF. (b) Measured transmission characteristics of the OADM based on SMF. Th: Through.
. It can be seen from in-to-out transmission characteristics for both LP11a and LP11b that, the dropped channel (at the center of the spectrum) is 25 dB below the through channel over a bandwidth of 0.5 nm. This ensures that the added signal will not be affected by in-band crosstalk. The loss for add, drop, and through channel are about 2.2, 2.1, 2.5 dB under the best operation condition, respectively. The add/drop transmission characteristics resembles a band-pass filter but with some ripples, which is caused by the beating between LP11 and residual LP01 modes. The residual LP01 can be attributed to many sources, such as imperfection of the mode converter, mode combiner, and even OADM. The transmission characteristics for LP01 mode of the OADM is also measured by removing the MC and MS and replacing TMF with SMF at each port. The LP01 mode is presented in Fig. 3(b), showing much smooth transmission characteristics due to immunity from LP01 and LP11 beating. This point to the difficulty of characterizing FMF based devices such as OADM. In other words, two-port transmission characteristics should be represented by a 4x4 input to output matrix, with both inputs and outputs could be a choice from any two polarizations of any two LP11 modes. This poses a huge challenge to fully measure the FMF compatible devices in terms of measurement complexity and a need for high-precision mode multiplexing and de-multiplexing devices.

To identify the polarization dependence, we insert SMF based polarization controller before MC and MS. By rotating the polarization state, we find there is no observable change on the OSA. From this we conclude that the polarization dependence of this OADM is insignificant (< 0.2 dB). The reason for such negligible polarization dependence is that we utilize thin-film filter with an angle of incident (AOI) as small as 5 degree.

3. Experimental setup

We use 3 channels to measure add, drop, and through functionalities of our custom-designed OADM, with the center channel to be dropped and added, and two outer channels to pass through. Each channel contains a multiband CO-OFDM signal consisting of 9 densely-spaced bands. Figure 4
Fig. 4 Experimental setup for TMF compatible OADM performance measurement. AWG: Arbitrary waveform generator, PBS: Polarization beam splitter, MS/C: Mode stripper/converter, BS: Beam Splitter, BPF: Band-pass filter, PD: Photodiode, ADC: Analog-to-digital converter, LD: Laser Diode.
shows the experimental setup used. The optical mode coupling from SMF to FMF and vice versa is achieved using two pairs of MS and MC. Free space mode combining and splitting is achieved with collimators and prism beam splitters (BS). There is an adjusting key assembled to each collimation port, to enable convenient adjustment of the orthogonality of the two LP11 patterns. Each channel is created by combining 3 external cavity lasers (ECLs), each carrying 3 tones spaced at 6.5185 GHz. Thus there are 9 tones in total for each channel. The frequency guard band between different lasers is 500 MHz. The 27 tones from 3 channels are combined and fed into an optical IQ modulator, which is driven by an OFDM signal. Then polarization multiplexing is emulated by splitting the CO-OFDM signal from IQ modulator into two branches that are delayed with each other by 1 OFDM symbol (500 ns), and recombined with a polarization beam splitter (PBS). We then emulate the signals for two orthogonal LP11 modes by splitting the signal and delaying one branch by two OFDM symbols (1 µs delay). These two signals are mode converted into LP11 mode using LPFG-based MCs, combined and launched using free-space optics into a 4 meter TMF fiber. The signal is then inserted into the input port of the OADM module. All the amplification is achieved by SMF EDFAs (namely, the amplifiers are placed either before LP01-to-LP11 conversion or after LP11-to-LP01 conversion). Since the TMF is linear in the demonstration, TMF channel effect is insignificant in this work which is focused on the OADM impact.

The OFDM parameters are: OFDM symbol length of 2560 points; cyclic prefix of 452 points; 4 OFDM training symbols are employed to represent alternate launch of 4 combinations of polarizations and modes, which is used for 4x4 channel matrix by means of intra-symbol averaging [19

19. X. Liu and F. Buchali, “Intra-symbol frequency-domain averaging based channel estimation for coherent optical OFDM,” Opt. Express 16(26), 21944–21957 (2008). [CrossRef] [PubMed]

]; unique word length of 32 used at each end of OFDM symbol to seed phase estimation for data symbols [20

20. X. Chen, A. Li, G. Gao, and W. Shieh, “Experimental demonstration of improved fiber nonlinearity tolerance for unique-word DFT-spread OFDM systems,” Opt. Express 19(27), 26198–26207 (2011). [CrossRef] [PubMed]

]. The phase estimation of training symbols is done by using RF pilot subcarrier [20

20. X. Chen, A. Li, G. Gao, and W. Shieh, “Experimental demonstration of improved fiber nonlinearity tolerance for unique-word DFT-spread OFDM systems,” Opt. Express 19(27), 26198–26207 (2011). [CrossRef] [PubMed]

,21

21. S. L. Jansen, I. Morita, T. C. W. Schenk, and H. Tanaka, “121.9-Gb/s PDM-OFDM transmission with 2 b/s/Hz spectral efficiency over 1,000 km of SSMF,” J. Lightwave Technol. 27(3), 177–188 (2009). [CrossRef]

]. The data symbols use DFT-spread (DFT-S) signal, and the phase estimation is done using decision feedback seeded by using unique word [20

20. X. Chen, A. Li, G. Gao, and W. Shieh, “Experimental demonstration of improved fiber nonlinearity tolerance for unique-word DFT-spread OFDM systems,” Opt. Express 19(27), 26198–26207 (2011). [CrossRef] [PubMed]

]. The three CO-OFDM channels each occupied 59.67 GHz bandwidth, carrying a net data rate of 318 Gb/s. All the BERs are calculated using 998,400 bits. Signal processing uses 4x4 MIMO OFDM procedure [18

18. A. Al Amin, A. Li, S. Chen, X. Chen, G. Gao, and W. Shieh, “Dual-LP11 mode 4×4 MIMO-OFDM transmission over a two-mode fiber,” Opt. Express 19(17), 16672–16679 (2011). [CrossRef] [PubMed]

].

4. Experimental results and discussion

Figure 5
Fig. 5 Measured spectra for transmitted signal, OADM through channels (w/ and w/o add channel), and the drop channel. (Curves have been shifted along the y-axis for comparison).
illustrates the optical spectra of transmitted superchannels spaced at 100 GHz and the MDM superchannels after OADM. From the spectra of the dropped channel and the through channel without add, it can be seen that the center channel have been effectively eliminated. The neighbor channel isolation is more than 25 dB determined from the spectrum at the drop port.

Figure 6(a)
Fig. 6 (a) Measured Q factor versus OSNR for add, drop and through channels at 318 Gb/s. Inset shows constellations for the add port signals at OSNR of 22.8 dB. (b) Q factor for all bands after OADM at an OSNR of 22.8 dB.
shows the Q factors of all the functionalities of OADM. The OSNRs are measured for the entire channel at 318 Gb/s. The Q factor (Q2 factor) is calculated from BER. It can be seen that the penalty at a 7% FEC limit (Q = 8.53 dB) for add, drop and through ports are 2.6, 2.4, 0.7 dB, respectively (through is averaged between left and right channels). Figure 6(b) presents the performance of all the bands for add, drop, through channels measured at an OSNR of 22.8 dB. It can be seen all the bands are below 7% FEC threshold of 8.53 dB. The inset shows the constellation for drop channel at an OSNR of 22.8 dB. We attribute the relatively large penalty to the beating between LP01 and LP11 modes.

Our work also reveals tremendous challenges ahead in characterizing FMF based components. There are a few critical elements needs to be developed to fully characterize the FMF based components. For instance, pure higher-order mode sources, high extinction-ratio mode-multiplexers and de-multiplexers are essential to identify the inter-modal interference of the few-mode compatible components under test. The first-order estimate is that the mode extinction ratio for those characterization devices should be better than 20 dB.

5. Conclusion

We have demonstrated for the first time an OADM that supports two orthogonal LP11 modes of a FMF. We perform add, drop and through functionalities for 3x318 Gb/s OFDM signals, and find that the OSNR penalties for add, drop and through ports are 2.6, 2.4, 0.7 dB, respectively.

References and links

1.

P. P. Mitra and J. B. Stark, “Nonlinear limits to the information capacity of optical fibre communications,” Nature 411(6841), 1027–1030 (2001). [CrossRef] [PubMed]

2.

R. J. Essiambre, G. Kramer, P. J. Winzer, G. J. Foschini, and B. Goebel, “Capacity limits of optical fiber networks,” J. Lightwave Technol. 28(4), 662–701 (2010). [CrossRef]

3.

X. Chen and W. Shieh, “Closed-form expressions for nonlinear transmission performance of densely spaced coherent optical OFDM systems,” Opt. Express 18(18), 19039–19054 (2010). [CrossRef] [PubMed]

4.

W. Shieh and X. Chen, “Information spectral efficiency and launch power density limits due to fiber nonlinearity for coherent optical OFDM systems,” IEEE Photon. J. 3(2), 158–173 (2011). [CrossRef]

5.

D. Qian, M. F. Huang, E. Ip, Y. K. Huang, Y. Shao, J. Hu, and T. Wang, “101.7-Tb/s (370 x 294-Gb/s) PDM-128QAM-OFDM transmission over 3 x 55-km SSMF using pilot-based phase noise mitigation,” Optical Fiber Communication Conference (OFC), 2011, PDPB5.

6.

J. Sakaguchi, Y. Awaji, N. Wada, A. Kanno, T. Kawanishi, T. Hayashi, T. Taru, T. Kobayashi, and M. Watanabe, “109-Tb/s (7×97×172-Gb/s SDM/WDM/PDM) QPSK transmission through 16.8-km homogeneous multi-core fiber,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB6.

7.

Y. Kokubun and M. Koshiba, “Novel multi-core fibers for mode division multiplexing: proposal and design principle,” IEICE Electron. Express 6(8), 522–528 (2009). [CrossRef]

8.

B. Zhu, T. Taunay, M. Fishteyn, X. Liu, S. Chandrasekhar, M. Yan, J. Fini, E. Monberg, and F. Dimarcello, “Space-, wavelength-, polarization-division multiplexed transmission of 56-Tb/s over a 76.8-km seven-core fiber,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB.7.

9.

N. Hanzawa, K. Saitoh, T. Sakamoto, T. Matsui, S. Tomita, and M. Koshiba, “Demonstration of mode-division multiplexing transmission over 10 km two-mode fiber with mode coupler,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, OWA4.

10.

A. Li, A. Al Amin, X. Chen, and W. Shieh, “ Reception of mode and polarization multiplexed 107-Gb/s CO-OFDM signal over a two-mode fiber” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB8.

11.

M. Salsi, C. Koebele, D. Sperti, P. Tran, P. Brindel, H. Mardoyan, S. Bigo, A. Boutin, F. Verluise, P. Sillard, M. Bigot-Astruc, L. Provost, F. Cerou, and G. Charlet, “Transmission at 2x100Gb/s, over two modes of 40km-long prototype few-mode fiber, using LCOS based mode multiplexer and demultiplexer,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB9.

12.

R. Ryf, S. Randel, A. H. Gnauck, C. Bolle, R. Essiambre, P. Winzer, D. W. Peckham, A. McCurdy, and R. Lingle, “Space-division multiplexing over 10 km of three-mode fiber using coherent 6 × 6 MIMO processing,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB10.

13.

E. Ip, B. Neng, Y. K. Huang, E. Mateo, F. Yaman, M. J. Li, S. Bickham, S. Ten, J. Linares, C. Montero, V. Moreno, X. Prieto, V. Tse, K. M. Chung, A. Lau, H. Y. Tam, C. Lu, Y. H. Luo, G. D. Peng, and G. Li, “88×3×112-Gb/s WDM transmission over 50 km of three-mode fiber with inline few-mode fiber amplifier”, in European Conference and Exposition on Optical Communications (ECOC), Geneva, Switzerland, 2011, Th.13.C.2.

14.

P. M. Krummrich, “Optical amplification and optical filter based signal processing for cost and energy efficient spatial multiplexing,” Opt. Express 19(17), 16636–16652 (2011). [CrossRef] [PubMed]

15.

R. Ryf, A. Sierra, R. Essiambre, S. Randel, A. Gnauck, C. A. Bolle, M. Esmaeelpour, P. J. Winzer, R. Delbue, P. Pupalaikis, A. Sureka, D. Peckham, A. McCurdy, and R. Lingle, “Mode-equalized distributed Raman amplification in 137-km few-mode Fiber,” in European Conference and Exposition on Optical Communications (ECOC), Geneva, Switzerland, 2011, Th.13.K.5.

16.

N. Bai, E. Ip, T. Wang, and G. Li, “Multimode fiber amplifier with tunable modal gain using a reconfigurable multimode pump,” Opt. Express 19(17), 16601–16611 (2011). [CrossRef] [PubMed]

17.

S. Tibuleac and M. Filer, “Transmission impairments in DWDM networks with reconfigurable optical add-drop multiplexers,” J. Lightwave Technol. 28(4), 557–598 (2010). [CrossRef]

18.

A. Al Amin, A. Li, S. Chen, X. Chen, G. Gao, and W. Shieh, “Dual-LP11 mode 4×4 MIMO-OFDM transmission over a two-mode fiber,” Opt. Express 19(17), 16672–16679 (2011). [CrossRef] [PubMed]

19.

X. Liu and F. Buchali, “Intra-symbol frequency-domain averaging based channel estimation for coherent optical OFDM,” Opt. Express 16(26), 21944–21957 (2008). [CrossRef] [PubMed]

20.

X. Chen, A. Li, G. Gao, and W. Shieh, “Experimental demonstration of improved fiber nonlinearity tolerance for unique-word DFT-spread OFDM systems,” Opt. Express 19(27), 26198–26207 (2011). [CrossRef] [PubMed]

21.

S. L. Jansen, I. Morita, T. C. W. Schenk, and H. Tanaka, “121.9-Gb/s PDM-OFDM transmission with 2 b/s/Hz spectral efficiency over 1,000 km of SSMF,” J. Lightwave Technol. 27(3), 177–188 (2009). [CrossRef]

OCIS Codes
(060.2330) Fiber optics and optical communications : Fiber optics communications
(060.4080) Fiber optics and optical communications : Modulation

ToC Category:
Fiber Optics and Optical Communications

History
Original Manuscript: March 7, 2012
Revised Manuscript: May 4, 2012
Manuscript Accepted: May 4, 2012
Published: June 12, 2012

Citation
Xi Chen, An Li, Jia Ye, Abdullah Al Amin, and William Shieh, "Reception of mode-division multiplexed superchannel via few-mode compatible optical add/drop multiplexer," Opt. Express 20, 14302-14307 (2012)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-20-13-14302


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. P. P. Mitra and J. B. Stark, “Nonlinear limits to the information capacity of optical fibre communications,” Nature411(6841), 1027–1030 (2001). [CrossRef] [PubMed]
  2. R. J. Essiambre, G. Kramer, P. J. Winzer, G. J. Foschini, and B. Goebel, “Capacity limits of optical fiber networks,” J. Lightwave Technol.28(4), 662–701 (2010). [CrossRef]
  3. X. Chen and W. Shieh, “Closed-form expressions for nonlinear transmission performance of densely spaced coherent optical OFDM systems,” Opt. Express18(18), 19039–19054 (2010). [CrossRef] [PubMed]
  4. W. Shieh and X. Chen, “Information spectral efficiency and launch power density limits due to fiber nonlinearity for coherent optical OFDM systems,” IEEE Photon. J.3(2), 158–173 (2011). [CrossRef]
  5. D. Qian, M. F. Huang, E. Ip, Y. K. Huang, Y. Shao, J. Hu, and T. Wang, “101.7-Tb/s (370 x 294-Gb/s) PDM-128QAM-OFDM transmission over 3 x 55-km SSMF using pilot-based phase noise mitigation,” Optical Fiber Communication Conference (OFC), 2011, PDPB5.
  6. J. Sakaguchi, Y. Awaji, N. Wada, A. Kanno, T. Kawanishi, T. Hayashi, T. Taru, T. Kobayashi, and M. Watanabe, “109-Tb/s (7×97×172-Gb/s SDM/WDM/PDM) QPSK transmission through 16.8-km homogeneous multi-core fiber,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB6.
  7. Y. Kokubun and M. Koshiba, “Novel multi-core fibers for mode division multiplexing: proposal and design principle,” IEICE Electron. Express6(8), 522–528 (2009). [CrossRef]
  8. B. Zhu, T. Taunay, M. Fishteyn, X. Liu, S. Chandrasekhar, M. Yan, J. Fini, E. Monberg, and F. Dimarcello, “Space-, wavelength-, polarization-division multiplexed transmission of 56-Tb/s over a 76.8-km seven-core fiber,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB.7.
  9. N. Hanzawa, K. Saitoh, T. Sakamoto, T. Matsui, S. Tomita, and M. Koshiba, “Demonstration of mode-division multiplexing transmission over 10 km two-mode fiber with mode coupler,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, OWA4.
  10. A. Li, A. Al Amin, X. Chen, and W. Shieh, “ Reception of mode and polarization multiplexed 107-Gb/s CO-OFDM signal over a two-mode fiber” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB8.
  11. M. Salsi, C. Koebele, D. Sperti, P. Tran, P. Brindel, H. Mardoyan, S. Bigo, A. Boutin, F. Verluise, P. Sillard, M. Bigot-Astruc, L. Provost, F. Cerou, and G. Charlet, “Transmission at 2x100Gb/s, over two modes of 40km-long prototype few-mode fiber, using LCOS based mode multiplexer and demultiplexer,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB9.
  12. R. Ryf, S. Randel, A. H. Gnauck, C. Bolle, R. Essiambre, P. Winzer, D. W. Peckham, A. McCurdy, and R. Lingle, “Space-division multiplexing over 10 km of three-mode fiber using coherent 6 × 6 MIMO processing,” Optical Fiber Communication Conference (OFC), Los Angeles, USA, 2011, PDPB10.
  13. E. Ip, B. Neng, Y. K. Huang, E. Mateo, F. Yaman, M. J. Li, S. Bickham, S. Ten, J. Linares, C. Montero, V. Moreno, X. Prieto, V. Tse, K. M. Chung, A. Lau, H. Y. Tam, C. Lu, Y. H. Luo, G. D. Peng, and G. Li, “88×3×112-Gb/s WDM transmission over 50 km of three-mode fiber with inline few-mode fiber amplifier”, in European Conference and Exposition on Optical Communications (ECOC), Geneva, Switzerland, 2011, Th.13.C.2.
  14. P. M. Krummrich, “Optical amplification and optical filter based signal processing for cost and energy efficient spatial multiplexing,” Opt. Express19(17), 16636–16652 (2011). [CrossRef] [PubMed]
  15. R. Ryf, A. Sierra, R. Essiambre, S. Randel, A. Gnauck, C. A. Bolle, M. Esmaeelpour, P. J. Winzer, R. Delbue, P. Pupalaikis, A. Sureka, D. Peckham, A. McCurdy, and R. Lingle, “Mode-equalized distributed Raman amplification in 137-km few-mode Fiber,” in European Conference and Exposition on Optical Communications (ECOC), Geneva, Switzerland, 2011, Th.13.K.5.
  16. N. Bai, E. Ip, T. Wang, and G. Li, “Multimode fiber amplifier with tunable modal gain using a reconfigurable multimode pump,” Opt. Express19(17), 16601–16611 (2011). [CrossRef] [PubMed]
  17. S. Tibuleac and M. Filer, “Transmission impairments in DWDM networks with reconfigurable optical add-drop multiplexers,” J. Lightwave Technol.28(4), 557–598 (2010). [CrossRef]
  18. A. Al Amin, A. Li, S. Chen, X. Chen, G. Gao, and W. Shieh, “Dual-LP11 mode 4×4 MIMO-OFDM transmission over a two-mode fiber,” Opt. Express19(17), 16672–16679 (2011). [CrossRef] [PubMed]
  19. X. Liu and F. Buchali, “Intra-symbol frequency-domain averaging based channel estimation for coherent optical OFDM,” Opt. Express16(26), 21944–21957 (2008). [CrossRef] [PubMed]
  20. X. Chen, A. Li, G. Gao, and W. Shieh, “Experimental demonstration of improved fiber nonlinearity tolerance for unique-word DFT-spread OFDM systems,” Opt. Express19(27), 26198–26207 (2011). [CrossRef] [PubMed]
  21. S. L. Jansen, I. Morita, T. C. W. Schenk, and H. Tanaka, “121.9-Gb/s PDM-OFDM transmission with 2 b/s/Hz spectral efficiency over 1,000 km of SSMF,” J. Lightwave Technol.27(3), 177–188 (2009). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited