Fast multiphoton microfabrication of freeform polymer microstructures by spatiotemporal focusing and patterned excitation

doi:10.1364/OE.20.019030

Fast multiphoton microfabrication of freeform polymer microstructures by spatiotemporal focusing and patterned excitation

Yi-Cheng Li, Li-Chung Cheng, Chia-Yuan Chang, Chi-Hsiang Lien, Paul J. Campagnola, and Shean-Jen Chen »View Author Affiliations

Optics Express, Vol. 20, Issue 17, pp. 19030-19038 (2012)
http://dx.doi.org/10.1364/OE.20.019030

View Full Text Article

Acrobat PDF (1135 KB)

Journal Search
Article Lookup

Article Tools

Citations

Alert me when this article is cited
Export Citation/Save

Article Navigation

▸ Article Outline
– Abstract
1. Introduction
2. Sample preparation and microfabrication setup
3. Experimental results and discussions
4. Conclusions
– References and links

Article Tools
Full Text
Article Info
References
Cited By
Figures
Multimedia
Metrics
Download PDF

Viewing Equations in the
HTML Article

Optimal Viewing Recommendations

Full Text
Article Info
References (28)
Cited By
Figures (6)
Multimedia (2)
Metrics

Abstract

One of the limits of conventional scanning multiphoton microfabrication is its low throughput due to point-by-point processing. In order to surpass this limit, a multiphoton microfabrication system based on spatiotemporal focusing and patterned excitation has been developed to quickly provide three-dimensional (3D) freeform polymer microstructures. 3D freeform polymer microstructures using Rose Bengal as the photoinitiator are created by sequentially stacking two-dimensional fabricating patterns. The size of each fabrication area can be larger than 300 × 170 μm² (full width at half maximum). Compared to conventional scanning multiphoton excitation and fixed mask pattern generation, this approach offers freeform microstructures and a greater than three-order increase in fabrication speed. Furthermore, the system is capable of optically sectioning the fabricated microstructures for providing 3D inspection.

1. Introduction

Multiphoton excitation (MPE) microfabrication is one of the most popular three-dimensional (3D) microfabrication techniques, and has been under development for over ten years. The utilization of a short pulse width from a femtosecond laser and tight focusing by a high numerical aperture (NA) objective lens are critical for inducing sufficient two-photon absorption (TPA) and for achieving high precision fabrication. Because TPA is confined to the focal volume, photopolymerized structures with the desired 3D submicron features can be created [1

S. Kawata, H. B. Sun, T. Tanaka, and K. Takada, “Finer features for functional microdevices,” Nature 412(6848), 697–698 (2001). [CrossRef] [PubMed]

–4

T. Tanaka, H. B. Sun, and S. Kawata, “Rapid sub-diffraction-limit laser micro/nanoprocessing in a threshold material system,” Appl. Phys. Lett. 80(2), 312–314 (2002). [CrossRef]

]. Recently, photopolymerization based on MPE has also been developed to further improve fabrication resolution since it uses low molecular weight photoinitiators to trigger reactions and requires an optical energy threshold to initiate the polymerization process [5

C. R. Lambert, I. E. Kochevar, and R. W. Redmond, “Differential reactivity of upper triplet states produces wavelength-dependent two-photon photosensitization using Rose Bengal,” J. Phys. Chem. B 103(18), 3737–3741 (1999). [CrossRef]

–7

P. J. Campagnola, D. M. Delguidice, G. A. Epling, K. D. Hoffacker, A. R. Howell, J. D. Pitts, and S. L. Goodman, “3-dimensional submicron polymerization of acrylamide by multiphoton excitation of xanthene dyes,” Macromolecules 33(5), 1511–1513 (2000). [CrossRef]

]. This approach not only allows the creation of structures beyond the capability of conventional single-photon lithography, but also provides greater spatial resolution than other 3D microfabrication techniques. As such, multiphoton photopolymerization has attracted widespread interest for its potential use in fabricating intrinsic 3D microstructures with sub-diffraction limited spatial resolution [1

S. Kawata, H. B. Sun, T. Tanaka, and K. Takada, “Finer features for functional microdevices,” Nature 412(6848), 697–698 (2001). [CrossRef] [PubMed]

]. Previously, femtosecond 3D microfabrication has been demonstrated in resin- [1

S. Kawata, H. B. Sun, T. Tanaka, and K. Takada, “Finer features for functional microdevices,” Nature 412(6848), 697–698 (2001). [CrossRef] [PubMed]

, 7

–9

Z. B. Sun, X. Z. Dong, W. Q. Chen, S. Nakanishi, M. Duan, and S. Kawata, “Multicolor polymer nanocomposites: in situ synthesis and fabrication of 3D microstructures,” Adv. Mater. (Deerfield Beach Fla.) 20(5), 914–919 (2008). [CrossRef]

], protein- [6

J. D. Pitts, P. J. Campagnola, G. A. Epling, and S. L. Goodman, “Submicron multiphoton free-form fabrication of proteins and polymers: studies of reaction efficiencies and applications in sustained release,” Macromolecules 33(5), 1514–1523 (2000). [CrossRef]

], and metal-substrates [10

P. W. Wu, W. C. Cheng, I. B. Martini, B. Dunn, B. J. Schwartz, and E. Yablonovitch, “Two-photon photographic production of three-dimensional metallic structures within a dielectric matrix,” Adv. Mater. (Deerfield Beach Fla.) 12(19), 1438–1441 (2000). [CrossRef]

, 11

Y. Y. Cao, N. Takeyasu, T. Tanaka, X. M. Duan, and S. Kawata, “3D metallic nanostructure fabrication by surfactant-assisted multiphoton-induced reduction,” Small 5(10), 1144–1148 (2009). [PubMed]

]. Photopolymerization by TPA encompasses a broad range of applications such as microfluidic systems [12

M. Stoneman, M. Fox, C. Y. Zeng, and V. Raicu, “Real-time monitoring of two-photon photopolymerization for use in fabrication of microfluidic devices,” Lab Chip 9(6), 819–827 (2009). [CrossRef] [PubMed]

], 3D optical storage devices [13

C. E. Olson, M. J. R. Previte, and J. T. Fourkas, “Efficient and robust multiphoton data storage in molecular glasses and highly crosslinked polymers,” Nat. Mater. 1(4), 225–228 (2002). [CrossRef] [PubMed]

], and photonic crystal structures [14

R. Guo, Z. Li, Z. Jiang, D. Yuan, W. Huang, and A. Xia, “Log-pile photonic crystal fabricated by two-photon photopolymerization,” J. Opt. A, Pure Appl. Opt. 7(8), 396–399 (2005). [CrossRef]

, 15

Z. B. Sun, X. Z. Dong, S. Nakanishi, W. Q. Chen, X. M. Duan, and S. Kawata, “Log-pile photonic crystal of CdS-polymer nanocomposites fabricated by combination of two-photon polymerization and in situ synthesis,” Appl. Phys., A Mater. Sci. Process. 86(4), 427–431 (2007). [CrossRef]

]. However, the major drawback of this approach is that it constructs 3D structures point-by-point rather than in parallel, as accomplished by photolithographic processing. As a result, TPA has very slow fabrication speed and is limited to laboratory investigation and prototype fabrication.

Recent studies have shown that using simultaneous spatial and temporal focusing techniques can provide widefield and axially-resolved multiphoton imaging [16

D. Oron, E. Tal, and Y. Silberberg, “Scanningless depth-resolved microscopy,” Opt. Express 13(5), 1468–1476 (2005). [CrossRef] [PubMed]

–21

O. D. Therrien, B. Aubé, S. Pagès, P. D. Koninck, and D. Côté, “Wide-field multiphoton imaging of cellular dynamics in thick tissue by temporal focusing and patterned illumination,” Biomed. Opt. Express 2(3), 696–704 (2011). [CrossRef] [PubMed]

]. The advantage of widefield multiphoton microscopy is that less time is required to capture one frame, enabling rapid frame rates for capturing dynamic events. With a high-speed, high-sensitivity camera and an ultrahigh peak power laser, an imaging rate of a few hundred frames per second can be achieved [22

L.-C. Cheng, C.-Y. Chang, C.-Y. Lin, K.-C. Cho, W.-C. Yen, N.-S. Chang, C. Xu, C. Y. Dong, and S.-J. Chen, “Spatiotemporal focusing-based widefield multiphoton microscopy for fast optical sectioning,” Opt. Express 20(8), 8939–8948 (2012). [CrossRef] [PubMed]

]. Furthermore, this microscopy setup can be modified as a high-throughput multiphoton microfabrication system for the micromachining of microfluidic channels and optically transparent materials with high aspect ratio features [23

F. He, H. Xu, Y. Cheng, J. Ni, H. Xiong, Z. Xu, K. Sugioka, and K. Midorikawa, “Fabrication of microfluidic channels with a circular cross section using spatiotemporally focused femtosecond laser pulses,” Opt. Lett. 35(7), 1106–1108 (2010). [CrossRef] [PubMed]

, 24

D. N. Vitek, D. E. Adams, A. Johnson, P. S. Tsai, S. Backus, C. G. Durfee, D. Kleinfeld, and J. A. Squier, “Temporally focused femtosecond laser pulses for low numerical aperture micromachining through optically transparent materials,” Opt. Express 18(17), 18086–18094 (2010). [CrossRef] [PubMed]

]. The spatiotemporal focusing technique uses a diffraction grating to separate frequencies spatially, and then recombines them on the focal plane of an objective lens. Only in that plane do the different frequency components overlap in phase and produce a short, high-peak power pulse, allowing effective MPE to occur. Further, depending on laser beam spot size and system magnification, the widefield and axially-resolved MPE can excite an entire area, which is a definite advantage compared with conventional point scanning MPE. Therefore, this technique provides a solution for high-speed MPE microfabrication and enables high-throughput manufacturing.

Previously, the spatiotemporal focusing technique with a fixed optical mask realized MPE microfabrication [25

D. Kim and P. T. C. So, “High-throughput three-dimensional lithographic microfabrication,” Opt. Lett. 35(10), 1602–1604 (2010). [CrossRef] [PubMed]

]. The mask was placed at the image-conjugate plane of the grating surface and the focal plane of the objective lens, and so any kind of 3D structure could be created by sequentially changing the optical mask layer-by-layer. However, the use of static optical masks limits fabrication speed and throughput; and since the light source is typically a Ti:sapphire (ti-sa) ultrafast oscillator, the fabrication area is further limited by the available peak power. In this study, in order to instantly generate 3D freeform polymer microstructures, a multiphoton microfabrication system based on spatiotemporal focusing and patterned excitation has been developed. This system incorporates a 10 kHz repetition rate ultrafast amplifier featuring strong instantaneous peak power (maximum 400 μJ/pulse at 90 fs pulse width) and a digital micromirror device (DMD) generating two-dimensional (2D) designed patterns on the focal plane. Since the diffraction grating was placed on the image-conjugate plane of the objective lens’ focal plane, the DMD generates designed 2D intensity patterns on the grating surface. Moreover, the size of the pattern is scaled by the magnification of the system; hence, increasing feature size does not require sacrificing fabrication speed. 3D freeform trimethylolpropane triacrylate (TMPTA) polymer microstructures using Rose Bengal (RB) as the photoinitiator were created by sequentially superimposing 2D structures while translating the sample stage axially. This approach can provide a greater than three-order increase in fabrication speed as compared to conventional point scanning MPE. In contrast with holographic femtosecond laser processing [26

S. Hasegawa and Y. Hayasaki, “Adaptive optimization of a hologram in holographic femtosecond laser processing system,” Opt. Lett. 34(1), 22–24 (2009). [CrossRef] [PubMed]

], the system can simultaneously provide additional nonlinear optical images of the fabricated microstructures for real-time 3D inspection.

2. Sample preparation and microfabrication setup

2.1. High-throughput multiphoton microfabrication system

Figure 1 illustrates a schematic of the developed high-throughput multiphoton microfabrication system based on spatiotemporal focusing and patterned excitation. Key components include a ti-sa ultrafast amplifier (Spitfire Pro., Newport, USA), an ultrafast oscillator (Tsunami, Newport, USA) as the seed beam of the amplifier, an upright optical microscope (Axio imager 2, Carl Zeiss, Germany), a triple-axis sample positioning stage (H101A ProScan^TM, Prior, UK), an Andor EMCCD camera (iXon^EM + 885 EMCCD, Andor, UK), a DMD (PJU-2100, RoyalTek, USA), and a data acquisition (DAQ) card with a field-programmable gate array (FPGA) module (PCI-7831R, National Instruments, USA). The ultrafast amplifier has a maximum peak power of 400 μJ/pulse and a pulse width of 90 fs at an average power of 4.0 W and a repetition rate of 10 kHz. First, a half-wave plate and a polarizer adjust the polarization and power of the amplifier; then, the beam oblique incidents on the DMD chip, which is controlled by a digital light processing technique, and generates the designed fabrication pattern. Following this, a relay lens pair is used to adjust the size of the pattern in order to fill the grating surface with focal lengths of 60 mm and 200 mm, respectively. The pulsing beam is spatially dispersed via a grating with a ruling density of 600 lines/mm and a size of 30 mm × 30 mm, the incident angle of which can be adjusted to ensure the dispersion’s central frequency follows the optical axis. A set of relay lenses with focal lengths of 250 mm and 75 mm was inserted to lengthen the beam path, allowing for active 2D wavefront correctors, such as deformable mirrors or spatial light modulators, to be inserted for adaptive optics corrections, which in turn modulate our temporal focusing technique to improve fabrication quality. The adaptive optics corrections have been described in detail previously [27

C.-Y. Chang, L.-C. Cheng, H.-W. Su, K.-C. Cho, W.-C. Yen, C. Xu, C. Y. Dong, and S.-J. Chen, “Widefield multiphoton microscopy with image-based adaptive optics system,” submitted for publication.

]. Herein, standard one inch diameter lenses are used. Finally, the dispersed frequencies propagate through the 4f setup, comprising the collimating lens with a focal length of 250 mm and the objective lens (EC Plan-NEOFLUAR 40X/ NA 1.3, Carl Zeiss, Germany), ultimately focusing on the front focal plane of the objective lens. The beam size incident on the back focal plane of the objective lens is around 10.1 mm × 85 μm and the beam's dimension on the sample is around 76 μm × 43 μm. All of the beam’s dimensions reflect full width at half maximum. However, if a 10X objective lens is utilized, the beam’s size on the sample can be larger than 300 μm × 170 μm. The diffraction from the grating has an oblique incident angle of 27.9°. By controlling the motorized stage in the z-axis via the FPGA, sequential 2D patterned MPE polymerizations at different depths can be quickly obtained. In addition, the system is equipped with both bright field and widefield multiphoton fluorescence optics, so white light or two-photon fluorescence images can be acquired during the fabrication process, which can be used as real-time diagnostics of the fabrication structures. The bright field optics includes a halogen illuminator as the light source and the objective lens used for the bright field is the same as mentioned above. The two-photon fluorescence images can be then rendered as a 3D image.

Fig. 1 Optical setup of the high-throughput multiphoton microfabrication system based on spatiotemporal focusing and patterned excitation.

Refractive elements such as the objective and collimating lenses can induce additional group velocity dispersion into the overall system. To correct this issue, the amplifier’s built-in prism pair was adjusted to approach the optimal pulse width (<120 fs); hence, temporal focusing efficiency for MPE polymerization can be enhanced, allowing for faster multiphoton microfabrication. Compared to holographic femtosecond laser processing [26

S. Hasegawa and Y. Hayasaki, “Adaptive optimization of a hologram in holographic femtosecond laser processing system,” Opt. Lett. 34(1), 22–24 (2009). [CrossRef] [PubMed]

], our system not only rapidly fabricates 3D freeform microstructures, but also provides fast optical sectioning. Patterned excitation is utilized for fabricating microstructures; however, uniform excitation is used to image the fabricated microstructures when the DMD is turned on. As a result, the contrast between the fabrication solution and the polymerized microstructures is sufficiently high [28

C.-Y. Lin, C.-H. Lien, K.-C. Cho, C.-Y. Chang, N.-S. Chang, P. J. Campagnola, C. Y. Dong, and S.-J. Chen, “Investigation of two-photon excited fluorescence increment via crosslinked bovine serum albumin,” Opt. Express 20(13), 13669–13676 (2012). [CrossRef] [PubMed]

], allowing for direct inspection of the microstructures during the fabrication procedure without washing out the fabrication solution or additional follow-up imaging.

2.2. Designing 3D freeform structures and sample preparation

In order to create 3D freeform microstructures with this microfabrication configuration, commercial CAD software such as AutoCAD, Pro/E, and Solidworks can be used to design any solid 3D structure. To transform 3D structures into 2D processing patterns, the 3D models were initially converted into STL format and saved as output files; then, the STL files were read by our LabVIEW code and converted into sequential 2D BMP files. Finally, the converted BMP files were read by another LabVIEW code that sequentially displays the sliced BMP patterns on a processing monitor. The DMD then synchronizes with the display patterns and generates patterned excitation on the focal plane of the objective lens.

A resin, ethoxylated TMPTA, was employed as the reactive monomer. The fabricated solution consisted of RB (Avocado Research Chemicals, UK) as the photoinitiator incorporated within a 0.1 M triethanolamine (TEA) co-initiator (Sigma-Aldrich, USA) solution, and mixed into a 75% (v/v) ethoxylated TMPTA (Sartomer, USA) solution. All chemicals and reagents were of analytical grade. According to our previous experimental results, the concentration of RB for 75% (v/v) TMPTA can be controlled at approximately 2.0 mM since a higher RB concentration is not necessary for the two-photon polymerization (TPP) process. Once completed, the 50 μl fabrication solution was confined in a small chamber created using a 50 μm-thick adhesive tape as a spacer to separate a 0.17 mm cover slip and the microscope slide. When fabricating, the structures were created from the bottom (slide) to top (slip) in order to prevent the incoming patterned excitation from being distorted by previous developed microstructures.

3. Experimental results and discussions

3.1. System calibrations

Microstructures cannot be created when the laser dose is below the threshold fabrication energy for conventional scanning multiphoton microfabrication; on the other hand, microstructures could be damaged by a relatively high laser dose. Furthermore, it was found that a small pattern increases fabrication difficulty as compared with a larger one under the same laser dose incident on the DMD chip during the high-throughput microfabrication process. Herein, the same laser dose means that the same laser power is utilized with the same pulse width and pulse number. Consequently, a suitable laser dose to match the size of the 2D fabricated pattern should be investigated. The power of the ultrafast amplifier cannot be rapidly changed; hence, the gray level of the DMD acts like an optical shutter and can be adopted to adjust the laser dose. Therefore, a dose-gray level relation was studied according to the ratio of the two-photon excitation fluorescence (TPEF) intensity (i.e. the laser excitation dose) to the gray level projected onto the DMD chip. The 0~255 gray levels represent the different “on” states for the 8-bit DMD, meaning that the DMD can act as a pulse selector to tune the pulse number on the fabricated pixel or area. For the 10 kHz ultrafast amplifier, a gray level of 255 represents 10,000 pulses per second, while a gray level of 128 refers to 5,000 pulses per second, and so on. Therefore, different gray levels for different sizes of fabricated patterns have been studied to further develop TMPTA polymer microstructures. Figure 2(a) shows the excitation of the normalized TPEF intensities of the fabricated solution as a function of different gray levels of the DMD. The TPEF intensity is nearly linearly proportional to the gray level, as shown in Fig. 2(a). Figure 2(b) illustrates that five different square pattern sizes can be fabricated with minimum gray levels of the DMD chip under the laser powers of 12.2 mW, 8.7 mW, and 5.2 mW (from top to bottom), respectively. The yellow numeral below each structure indicates the approximate minimum gray level required for fabrication under the three respective laser powers. The experimental results confirm that a larger pattern can be developed with a lower gray level (i.e. lower laser dose) under the proposed process. Interestingly, the first row of Fig. 2(b) demonstrates that although a suitable high laser power is provided, a higher gray level is required for a small pattern, while a lower gray level is needed for a larger pattern. Additionally, a low laser dose can prevent the fabricated microstructure from being damaged. However, if the laser power is insufficient, despite employing the highest gray level, microstructures cannot be fabricated or their shapes will have slight deformations, as shown in the last row of Fig. 2(b).

Fig. 2 (a) Normalized TPEF intensities of fabricated solution as a function of different gray levels of the DMD. (b) Bright-field images of 5 different sizes of TMPTA polymer microstructures with the use of three different laser powers at 12.2 mW, 8.7 mW, and 5.2 mW (from top to bottom) corresponding to the minimum demanded gray levels, respectively. Sizes of the fabricated squares are respectively 42 μm, 33 μm, 23 μm, 14 μm, and 8 μm (from left to right).

The 4f setup is utilized to realize the spatiotemporal focusing, so the line-shape and unpulsing beam on the back focal plane of the objective lens may not damage the objective lens so easily. If the damage is eliminated and the reflection rate of the DMD can be higher than 80%, then the maximum fluence per pulse on the sample through the widefield system with the 4.0 W amplifier can achieve 185 μJ. Currently, some multiphoton fabrication and laser ablation experiments for bio-applications are studying. For example, 5~20 μJ/pulse is large enough to fabricate bovine serum albumin microstructures for the area of 76 μm × 43 μm. For the laser ablation, the level of laser fluence should be higher than 50 μJ/pulse.

The lateral fabrication resolution of the high-throughput multiphoton microfabrication system is in need of clarification for further processing. A fabrication area of 76 μm × 43 μm under the system setup corresponds to the 640 × 360 pixel number of the DMD chip, indicating that 1 pixel corresponds to roughly 120 nm × 120 nm. Three stripe patterns with pixel numbers of 35, 20, and 5 were fabricated to examine the lateral resolution, the estimated sizes of which are around 4.2 μm, 2.4 μm, and 0.6 μm, respectively. However, Figs. 3(a) , 3(b), & 3(c) show that the widths of the stripes are approximately 3.8 μm, 1.6 μm, and 1μm, respectively. In this regard, photopolymerization requires the threshold fabrication energy to initiate the process, and so actual fabricated sizes could be slightly smaller than the estimated size. As such, the stripes in Figs. 3(a) & 3(b) match expectations, but the width of the stripes in Fig. 3(c) is only 1 μm, which may stem from the diffraction limit and/or system distortions. Currently, the lateral fabrication resolution of the system is around 1 μm.

Fig. 3 Bright-field images and profiles of three stripes fabricated with pixel numbers of (a) 35, (b) 20, and (c) 5, respectively. The corresponding widths of the stripes are 3.8 μm, 1.6 μm, and 1 μm, respectively. The profiles correspond to the red dotted line in the bright-field images.

3.2. Fabrication and inspection of freeform polymer microstructures

For 3D freeform microfabrication, the sequential 2D bitmap files sliced from a designed 3D CAD model were downloaded into the LabVIEW program to sequentially implement the 2D pattern excitation via the DMD. The 2D TPP microstructures were sequentially formed on the focal plane based on spatiotemporal focusing and patterned excitation, and then stacked in a 3D polymer microstructure while translating the sample stage axially. The remaining fabrication solution was then washed with water. To sufficiently support the MPE photochemistry process in the fabrication solution, a laser power of at least a few mWs at the excitation time of around 1 second was adopted. Figures 4(a) , 4(b) & 4(c) show the 3D rendering of the TPEF images by using our lab-made conventional point scanning TPEF microscope. The corresponding bright field images are inserted. Figure 4(a) shows a fabricated star structure with a feature size of around 30 μm under a laser power of 8.7 mW, an excitation time of 4/3 seconds, and a z-axis step of 1 μm. Unlike conventional scanning multiphoton microfabrication, the proposed system can increase feature size without sacrificing fabrication speed. Figures 4(b) & 4(c) demonstrate that bigger microstructures can be created using smaller magnifications of the optical system. The magnification for Fig. 4(a) is 40X; however, the magnifications for Figs. 4(b) & 4(c) were reduced to 20X and 10X, while the feature sizes were enlarged to 60 μm and 120 μm, respectively. The excitation areas were enlarged, so the laser powers were also increased to 12.2 mW and 15.7 mW for Figs. 4(b) & 4(c), respectively. The fabrication times of these three microstructures were equal, requiring only 40 seconds. Therefore, it is possible to increase the fabrication area by readjusting the magnification of the optical system, such as the objective lens and the relay lens pair in Fig. 1.

Fig. 4 TPEF images of different size microstructures created by different magnifications of the objective lenses at (a) 40X, (b) 20X, and (c) 10X. The heights of three structures are all 30 μm.

In addition to the above scale-up capability, the 3D renderings of the TPEF images of the excitation patterns can be viewed in real-time during the high-throughput microfabrication process, as shown in Fig. 5 . The front-view bright-field images of the fabricated microstructures before rinsing the remaining solution are inserted in the 3D renderings. Figure 5(a) displays a 3D pyramid structure, where the base area is around 40 × 40 μm² while the height is 45 μm. The fabrication laser power was 7.5 mW, the excitation time was 4/3 seconds per layer, and the z-axis step was 1 μm. Figure 5(b) demonstrates that four different shaped structures with different heights can be fabricated simultaneously. The heights are 8μm, 12 μm, 16 μm, and 20 μm for the triangle, star, rectangle, and circle, respectively. The fabrication time for developing these microstructures is within 30 seconds.

Fig. 5 3D renderings of the TPEF images of the excitation patterns during the high-throughput microfabrication process: (a) pyramid structure and (b) multiple objects (triangle, star, rectangle, and circle) with different heights. Inset: 2D front-view bright-field images.

After washing the remaining solution, the developed microstructures in Fig. 5(b) were imaged again using our lab-made conventional point scanning TPEF microscope. Figure 6(a) shows the 3D rendering of the TPEF image of the developed microstructures. The shapes in Fig. 6(a) are nearly identical to Fig. 5(b), thus providing further evidence that the TPEF images grabbed during the high-throughput fabrication process can be utilized as online diagnostics for fabricating microstructures. Therefore, the proposed system based on spatiotemporal focusing and patterned excitation not only provides high-throughput microfabrication, but also offers real-time optical sectioning for 3D online inspection. The microstructures in Fig. 5(b) were imaged again using the multiphoton microfabrication system with only the widefield imaging function, as shown in Fig. 6(b). Namely, the TPEF images were got via plane by plane, and then rendered into a 3D image. Compared with Fig. 6(a), the image looks somewhat blurry; nevertheless, according to our previous study [27

C.-Y. Chang, L.-C. Cheng, H.-W. Su, K.-C. Cho, W.-C. Yen, C. Xu, C. Y. Dong, and S.-J. Chen, “Widefield multiphoton microscopy with image-based adaptive optics system,” submitted for publication.

], the image quality can be improved to achieve sub-micron resolution.

Fig. 6 3D renderings of the TPEF images of the fabricated microstructures in Fig. 5(b) after washing the remaining solution using: (a) typical scanning multiphoton microscope (Media 1), and (b) multiphoton microfabrication system with only the widefield microscopy function (Media 2).

4. Conclusions

A multiphoton microfabrication system based on spatiotemporal focusing and patterned excitation has been developed to enhance fabrication speed and also realize microfabrication of 3D freeform microstructures. 3D freeform polymer microstructures can be created by sequentially stacking 2D structures. The fabrication times for developing microstructures require less than one minute. Compared with conventional scanning MPE microfabrication, this approach provides an increase in fabrication speed of more than three-order, offering the possibility of mass-production, while simultaneously providing real-time optical sectioning for the fabricated microstructures. Therefore, the multiphoton microfabrication system not only provides the capability of high-throughput microfabrication, but also offers optical sectioning for 3D online inspection.

Acknowledgments

This work was supported by the National Science Council (NSC) in Taiwan with the grant numbers of NSC 99-2627-B-006-017 and NSC 99-2320-B-006-012-MY3.

References and links

1.	S. Kawata, H. B. Sun, T. Tanaka, and K. Takada, “Finer features for functional microdevices,” Nature 412(6848), 697–698 (2001). [CrossRef] [PubMed]
2.	W. Denk, J. H. Strickler, and W. W. Webb, “Two-photon laser scanning fluorescence microscopy,” Science 248(4951), 73–76 (1990). [CrossRef] [PubMed]
3.	M. Miwa, S. Juodkazis, T. Kawakami, S. Matsuo, and H. Misawa, “Femtosecond two-photon stereo-lithography,” Appl. Phys., A Mater. Sci. Process. 73(5), 561–566 (2001). [CrossRef]
4.	T. Tanaka, H. B. Sun, and S. Kawata, “Rapid sub-diffraction-limit laser micro/nanoprocessing in a threshold material system,” Appl. Phys. Lett. 80(2), 312–314 (2002). [CrossRef]
5.	C. R. Lambert, I. E. Kochevar, and R. W. Redmond, “Differential reactivity of upper triplet states produces wavelength-dependent two-photon photosensitization using Rose Bengal,” J. Phys. Chem. B 103(18), 3737–3741 (1999). [CrossRef]
6.	J. D. Pitts, P. J. Campagnola, G. A. Epling, and S. L. Goodman, “Submicron multiphoton free-form fabrication of proteins and polymers: studies of reaction efficiencies and applications in sustained release,” Macromolecules 33(5), 1514–1523 (2000). [CrossRef]
7.	P. J. Campagnola, D. M. Delguidice, G. A. Epling, K. D. Hoffacker, A. R. Howell, J. D. Pitts, and S. L. Goodman, “3-dimensional submicron polymerization of acrylamide by multiphoton excitation of xanthene dyes,” Macromolecules 33(5), 1511–1513 (2000). [CrossRef]
8.	T. Watanabe, M. Akiyama, K. Totani, S. M. Kuebler, F. Stellacci, W. Wenseleers, K. Braun, S. R. Marder, and J. W. Perry, “Photoresponsive hydrogel microstructure fabricated by two-photon initiated Polymerization,” Adv. Funct. Mater. 12(9), 611–614 (2002). [CrossRef]
9.	Z. B. Sun, X. Z. Dong, W. Q. Chen, S. Nakanishi, M. Duan, and S. Kawata, “Multicolor polymer nanocomposites: in situ synthesis and fabrication of 3D microstructures,” Adv. Mater. (Deerfield Beach Fla.) 20(5), 914–919 (2008). [CrossRef]
10.	P. W. Wu, W. C. Cheng, I. B. Martini, B. Dunn, B. J. Schwartz, and E. Yablonovitch, “Two-photon photographic production of three-dimensional metallic structures within a dielectric matrix,” Adv. Mater. (Deerfield Beach Fla.) 12(19), 1438–1441 (2000). [CrossRef]
11.	Y. Y. Cao, N. Takeyasu, T. Tanaka, X. M. Duan, and S. Kawata, “3D metallic nanostructure fabrication by surfactant-assisted multiphoton-induced reduction,” Small 5(10), 1144–1148 (2009). [PubMed]
12.	M. Stoneman, M. Fox, C. Y. Zeng, and V. Raicu, “Real-time monitoring of two-photon photopolymerization for use in fabrication of microfluidic devices,” Lab Chip 9(6), 819–827 (2009). [CrossRef] [PubMed]
13.	C. E. Olson, M. J. R. Previte, and J. T. Fourkas, “Efficient and robust multiphoton data storage in molecular glasses and highly crosslinked polymers,” Nat. Mater. 1(4), 225–228 (2002). [CrossRef] [PubMed]
14.	R. Guo, Z. Li, Z. Jiang, D. Yuan, W. Huang, and A. Xia, “Log-pile photonic crystal fabricated by two-photon photopolymerization,” J. Opt. A, Pure Appl. Opt. 7(8), 396–399 (2005). [CrossRef]
15.	Z. B. Sun, X. Z. Dong, S. Nakanishi, W. Q. Chen, X. M. Duan, and S. Kawata, “Log-pile photonic crystal of CdS-polymer nanocomposites fabricated by combination of two-photon polymerization and in situ synthesis,” Appl. Phys., A Mater. Sci. Process. 86(4), 427–431 (2007). [CrossRef]
16.	D. Oron, E. Tal, and Y. Silberberg, “Scanningless depth-resolved microscopy,” Opt. Express 13(5), 1468–1476 (2005). [CrossRef] [PubMed]
17.	G. Zhu, J. van Howe, M. Durst, W. Zipfel, and C. Xu, “Simultaneous spatial and temporal focusing of femtosecond pulses,” Opt. Express 13(6), 2153–2159 (2005). [CrossRef] [PubMed]
18.	M. E. Durst, G. Zhu, and C. Xu, “Simultaneous spatial and temporal focusing in nonlinear microscopy,” Opt. Commun. 281(7), 1796–1805 (2008). [CrossRef] [PubMed]
19.	A. Vaziri, J. Tang, H. Shroff, and C. V. Shank, “Multilayer three-dimensional super resolution imaging of thick biological samples,” Proc. Natl. Acad. Sci. U.S.A. 105(51), 20221–20226 (2008). [CrossRef] [PubMed]
20.	E. Papagiakoumou, F. Anselmi, A. Bègue, V. de Sars, J. Glückstad, E. Y. Isacoff, and V. Emiliani, “Scanless two-photon excitation of channelrhodopsin-2,” Nat. Methods 7(10), 848–854 (2010). [CrossRef] [PubMed]
21.	O. D. Therrien, B. Aubé, S. Pagès, P. D. Koninck, and D. Côté, “Wide-field multiphoton imaging of cellular dynamics in thick tissue by temporal focusing and patterned illumination,” Biomed. Opt. Express 2(3), 696–704 (2011). [CrossRef] [PubMed]
22.	L.-C. Cheng, C.-Y. Chang, C.-Y. Lin, K.-C. Cho, W.-C. Yen, N.-S. Chang, C. Xu, C. Y. Dong, and S.-J. Chen, “Spatiotemporal focusing-based widefield multiphoton microscopy for fast optical sectioning,” Opt. Express 20(8), 8939–8948 (2012). [CrossRef] [PubMed]
23.	F. He, H. Xu, Y. Cheng, J. Ni, H. Xiong, Z. Xu, K. Sugioka, and K. Midorikawa, “Fabrication of microfluidic channels with a circular cross section using spatiotemporally focused femtosecond laser pulses,” Opt. Lett. 35(7), 1106–1108 (2010). [CrossRef] [PubMed]
24.	D. N. Vitek, D. E. Adams, A. Johnson, P. S. Tsai, S. Backus, C. G. Durfee, D. Kleinfeld, and J. A. Squier, “Temporally focused femtosecond laser pulses for low numerical aperture micromachining through optically transparent materials,” Opt. Express 18(17), 18086–18094 (2010). [CrossRef] [PubMed]
25.	D. Kim and P. T. C. So, “High-throughput three-dimensional lithographic microfabrication,” Opt. Lett. 35(10), 1602–1604 (2010). [CrossRef] [PubMed]
26.	S. Hasegawa and Y. Hayasaki, “Adaptive optimization of a hologram in holographic femtosecond laser processing system,” Opt. Lett. 34(1), 22–24 (2009). [CrossRef] [PubMed]
27.	C.-Y. Chang, L.-C. Cheng, H.-W. Su, K.-C. Cho, W.-C. Yen, C. Xu, C. Y. Dong, and S.-J. Chen, “Widefield multiphoton microscopy with image-based adaptive optics system,” submitted for publication.
28.	C.-Y. Lin, C.-H. Lien, K.-C. Cho, C.-Y. Chang, N.-S. Chang, P. J. Campagnola, C. Y. Dong, and S.-J. Chen, “Investigation of two-photon excited fluorescence increment via crosslinked bovine serum albumin,” Opt. Express 20(13), 13669–13676 (2012). [CrossRef] [PubMed]

OCIS Codes
(120.4610) Instrumentation, measurement, and metrology : Optical fabrication
(190.4180) Nonlinear optics : Multiphoton processes
(180.4315) Microscopy : Nonlinear microscopy

ToC Category:
Laser Microfabrication

History
Original Manuscript: June 1, 2012
Revised Manuscript: July 19, 2012
Manuscript Accepted: July 28, 2012
Published: August 3, 2012

Virtual Issues
Vol. 7, Iss. 10 Virtual Journal for Biomedical Optics

Citation
Yi-Cheng Li, Li-Chung Cheng, Chia-Yuan Chang, Chi-Hsiang Lien, Paul J. Campagnola, and Shean-Jen Chen, "Fast multiphoton microfabrication of freeform polymer microstructures by spatiotemporal focusing and patterned excitation," Opt. Express 20, 19030-19038 (2012)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-20-17-19030

Sort: Author | Year | Journal | Reset

References

S. Kawata, H. B. Sun, T. Tanaka, and K. Takada, “Finer features for functional microdevices,” Nature412(6848), 697–698 (2001). [CrossRef] [PubMed]
W. Denk, J. H. Strickler, and W. W. Webb, “Two-photon laser scanning fluorescence microscopy,” Science248(4951), 73–76 (1990). [CrossRef] [PubMed]
M. Miwa, S. Juodkazis, T. Kawakami, S. Matsuo, and H. Misawa, “Femtosecond two-photon stereo-lithography,” Appl. Phys., A Mater. Sci. Process.73(5), 561–566 (2001). [CrossRef]
T. Tanaka, H. B. Sun, and S. Kawata, “Rapid sub-diffraction-limit laser micro/nanoprocessing in a threshold material system,” Appl. Phys. Lett.80(2), 312–314 (2002). [CrossRef]
C. R. Lambert, I. E. Kochevar, and R. W. Redmond, “Differential reactivity of upper triplet states produces wavelength-dependent two-photon photosensitization using Rose Bengal,” J. Phys. Chem. B103(18), 3737–3741 (1999). [CrossRef]
J. D. Pitts, P. J. Campagnola, G. A. Epling, and S. L. Goodman, “Submicron multiphoton free-form fabrication of proteins and polymers: studies of reaction efficiencies and applications in sustained release,” Macromolecules33(5), 1514–1523 (2000). [CrossRef]
P. J. Campagnola, D. M. Delguidice, G. A. Epling, K. D. Hoffacker, A. R. Howell, J. D. Pitts, and S. L. Goodman, “3-dimensional submicron polymerization of acrylamide by multiphoton excitation of xanthene dyes,” Macromolecules33(5), 1511–1513 (2000). [CrossRef]
T. Watanabe, M. Akiyama, K. Totani, S. M. Kuebler, F. Stellacci, W. Wenseleers, K. Braun, S. R. Marder, and J. W. Perry, “Photoresponsive hydrogel microstructure fabricated by two-photon initiated Polymerization,” Adv. Funct. Mater.12(9), 611–614 (2002). [CrossRef]
Z. B. Sun, X. Z. Dong, W. Q. Chen, S. Nakanishi, M. Duan, and S. Kawata, “Multicolor polymer nanocomposites: in situ synthesis and fabrication of 3D microstructures,” Adv. Mater. (Deerfield Beach Fla.)20(5), 914–919 (2008). [CrossRef]
P. W. Wu, W. C. Cheng, I. B. Martini, B. Dunn, B. J. Schwartz, and E. Yablonovitch, “Two-photon photographic production of three-dimensional metallic structures within a dielectric matrix,” Adv. Mater. (Deerfield Beach Fla.)12(19), 1438–1441 (2000). [CrossRef]
Y. Y. Cao, N. Takeyasu, T. Tanaka, X. M. Duan, and S. Kawata, “3D metallic nanostructure fabrication by surfactant-assisted multiphoton-induced reduction,” Small5(10), 1144–1148 (2009). [PubMed]
M. Stoneman, M. Fox, C. Y. Zeng, and V. Raicu, “Real-time monitoring of two-photon photopolymerization for use in fabrication of microfluidic devices,” Lab Chip9(6), 819–827 (2009). [CrossRef] [PubMed]
C. E. Olson, M. J. R. Previte, and J. T. Fourkas, “Efficient and robust multiphoton data storage in molecular glasses and highly crosslinked polymers,” Nat. Mater.1(4), 225–228 (2002). [CrossRef] [PubMed]
R. Guo, Z. Li, Z. Jiang, D. Yuan, W. Huang, and A. Xia, “Log-pile photonic crystal fabricated by two-photon photopolymerization,” J. Opt. A, Pure Appl. Opt.7(8), 396–399 (2005). [CrossRef]
Z. B. Sun, X. Z. Dong, S. Nakanishi, W. Q. Chen, X. M. Duan, and S. Kawata, “Log-pile photonic crystal of CdS-polymer nanocomposites fabricated by combination of two-photon polymerization and in situ synthesis,” Appl. Phys., A Mater. Sci. Process.86(4), 427–431 (2007). [CrossRef]
D. Oron, E. Tal, and Y. Silberberg, “Scanningless depth-resolved microscopy,” Opt. Express13(5), 1468–1476 (2005). [CrossRef] [PubMed]
G. Zhu, J. van Howe, M. Durst, W. Zipfel, and C. Xu, “Simultaneous spatial and temporal focusing of femtosecond pulses,” Opt. Express13(6), 2153–2159 (2005). [CrossRef] [PubMed]
M. E. Durst, G. Zhu, and C. Xu, “Simultaneous spatial and temporal focusing in nonlinear microscopy,” Opt. Commun.281(7), 1796–1805 (2008). [CrossRef] [PubMed]
A. Vaziri, J. Tang, H. Shroff, and C. V. Shank, “Multilayer three-dimensional super resolution imaging of thick biological samples,” Proc. Natl. Acad. Sci. U.S.A.105(51), 20221–20226 (2008). [CrossRef] [PubMed]
E. Papagiakoumou, F. Anselmi, A. Bègue, V. de Sars, J. Glückstad, E. Y. Isacoff, and V. Emiliani, “Scanless two-photon excitation of channelrhodopsin-2,” Nat. Methods7(10), 848–854 (2010). [CrossRef] [PubMed]
O. D. Therrien, B. Aubé, S. Pagès, P. D. Koninck, and D. Côté, “Wide-field multiphoton imaging of cellular dynamics in thick tissue by temporal focusing and patterned illumination,” Biomed. Opt. Express2(3), 696–704 (2011). [CrossRef] [PubMed]
L.-C. Cheng, C.-Y. Chang, C.-Y. Lin, K.-C. Cho, W.-C. Yen, N.-S. Chang, C. Xu, C. Y. Dong, and S.-J. Chen, “Spatiotemporal focusing-based widefield multiphoton microscopy for fast optical sectioning,” Opt. Express20(8), 8939–8948 (2012). [CrossRef] [PubMed]
F. He, H. Xu, Y. Cheng, J. Ni, H. Xiong, Z. Xu, K. Sugioka, and K. Midorikawa, “Fabrication of microfluidic channels with a circular cross section using spatiotemporally focused femtosecond laser pulses,” Opt. Lett.35(7), 1106–1108 (2010). [CrossRef] [PubMed]
D. N. Vitek, D. E. Adams, A. Johnson, P. S. Tsai, S. Backus, C. G. Durfee, D. Kleinfeld, and J. A. Squier, “Temporally focused femtosecond laser pulses for low numerical aperture micromachining through optically transparent materials,” Opt. Express18(17), 18086–18094 (2010). [CrossRef] [PubMed]
D. Kim and P. T. C. So, “High-throughput three-dimensional lithographic microfabrication,” Opt. Lett.35(10), 1602–1604 (2010). [CrossRef] [PubMed]
S. Hasegawa and Y. Hayasaki, “Adaptive optimization of a hologram in holographic femtosecond laser processing system,” Opt. Lett.34(1), 22–24 (2009). [CrossRef] [PubMed]
C.-Y. Chang, L.-C. Cheng, H.-W. Su, K.-C. Cho, W.-C. Yen, C. Xu, C. Y. Dong, and S.-J. Chen, “Widefield multiphoton microscopy with image-based adaptive optics system,” submitted for publication.
C.-Y. Lin, C.-H. Lien, K.-C. Cho, C.-Y. Chang, N.-S. Chang, P. J. Campagnola, C. Y. Dong, and S.-J. Chen, “Investigation of two-photon excited fluorescence increment via crosslinked bovine serum albumin,” Opt. Express20(13), 13669–13676 (2012). [CrossRef] [PubMed]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Click here to see a list of articles that cite this paper