« journal navigation
|
A 10Gb/s APD-based linear burst-mode receiver with 31dB dynamic range for reach-extended PON systems |
Optics Express, Vol. 20, Issue 26, pp. B462-B469 (2012)
http://dx.doi.org/10.1364/OE.20.00B462
Acrobat PDF (1603 KB)
Article Navigation
▸ Article Outline
– Abstract
1. Introduction
2. Realization of the APD linear BM-RX with self-generated M-control signal
3. Experimental setup
4. Experimental results
5. Conclusions
– References and links
– Abstract
1. Introduction
2. Realization of the APD linear BM-RX with self-generated M-control signal
3. Experimental setup
4. Experimental results
5. Conclusions
– References and links
Article Tools
Full Text
Article Info
References
Cited By
Figures
Metrics
Download PDF
Viewing Equations in the
HTML Article
Optimal Viewing Recommendations
Abstract
We present for the first time a high performance APD-based linear burst-mode receiver (BM-RX) with a record wide dynamic range of 31dB. The APD multiplication factor is controlled from burst to burst within 60ns by an on-chip self-generated M-control signal. In the experiment, a total optical budget of 54dB is achieved with a single SOA-based reach extender for 10Gb/s upstream. With electronic dispersion compensation, the APD linear BM-RX with a wide dynamic range relaxes the requirement on optical components and lowers the system cost, especially at the optical network unit (ONU) side.
© 2012 OSA
1. Introduction
Passive optical network (PON) systems are being widely deployed as a most cost-effective solution for optical access networks. Some recent research focused on upgrading existing PON systems with extended reach and increased splitting ratio [1–3]. Extending the link reach enables rural subscriber services while maintaining the PON’s cost benefits, and increasing the splitting ratio allows offering services to urban subscribers with reduced number of optical line terminals (OLTs).
Although the majority of existing OLTs employ a burst-mode receiver (BM-RX) with a limiting amplifier, the link reach can be further extended using an APD-based linear BM-RX, which allows the use of electronic equalization techniques [4]. As the link reach is extended, the possible difference between upstream burst signal intensities from different optical network units (ONUs) is also increased. Therefore, not only high receiver sensitivity but also a wide dynamic range is of an important consideration for the requirement of the APD linear BM-RX. The APD-based solution allows the linear BM-RX to operate without an optical pre-amplifier and the bias-dependent multiplication factor (M) adds another degree of freedom to increase the linear operation range. The 10Gb/s PIN-based linear BM-RX in [5,6] had a dynamic range of 22.7dB. In the final experimental setup, an erbium doped fiber amplifier (EDFA) before the PIN-based linear BM-RX was used as a pre-amplifier. Reference [7] described a 10Gb/s limiting-type BM-RX using an external signal to control the APD’s multiplication factor (M-control) and achieved a dynamic range of 24.4dB. Recently, we have demonstrated a high performance limiting-type BM-RX supporting multi-rate (2.5G/5G/10Gb/s) upstream with more than 26.3dB dynamic range without using APD M-control [8].
T. Nakanishi, Y. Fukuda, K. Suzuki, N. Yoshimoto, M. Nakamura, K. Kato, K. Nishimura, Y. Ohtomo, and M. Tsubokawa, “Wide dynamic range and high sensitivity APD burst receiver configuration based on M-switching technique for 10GEPON system,” in Proceedings of Lasers and Electro-Optics Society (Institute of Electrical and Electronics Engineers, 2007), Paper ThW5.
X. Yin, X. Z. Qiu, J. Gillis, J. Put, J. Verbrugghe, J. Bauwelinck, J. Vandewege, H. Krimmel, D. van Veen, P. Vetter, and F. Chang, “Experiments on 10Gb/s fast settling high sensitivity burst-mode receiver with on-chip auto-reset for 10G-GPONs [Invited],” J. Opt. Commun. Netw. 4(11), B68–B76 (2012). [CrossRef]
In this paper, we report, for the first time, an APD-based linear burst-mode receiver with a dynamic range of 31dB, by using an on-chip self-generated M-control signal [9]. In addition, the proposed APD-based linear BM-RX technique is also intended to relax the requirement on optical components and lower the system cost, especially at ONU side. Our experiment shows that a lower bandwidth/performance optical transmitter can be used at the ONU for 10Gb/s upstream transmission with the proposed APD linear BM-RX. The remainder of the paper is organized as follows. The realization of the APD linear BM-RX and APD bias circuit are discussed in details in Section 2. Section 3 and Section 4 present the experimental setup and results. We finally conclude in Section 5.
X. Yin, B. Moeneclaey, X. Z. Qiu, J. Verbrugghe, K. Verheyen, J. Bauwelinck, J. Vandewege, M. Achouche, and F. Y. Chang, “A 10Gb/s APD-based linear burst-mode receiver with 31dB dynamic range for reach-extended PON systems,” in Proceedings of European Conference Optical Communication, (2012), Paper Tu.1.B.5.
2. Realization of the APD linear BM-RX with self-generated M-control signal
Figure 1
shows the proposed 10Gb/s APD linear BM-RX architecture. The linear BM-RX consists of a transimpedance amplifier (TIA) stage, a variable gain amplifier (VGA), and a linear output buffer. At the start of each burst, the fast automatic gain control (AGC) senses the output amplitude of the TIAc core and set its transimpedance gain within 10ns. After the transimpedance gain is stabilized, the output amplitude of the TIAc core is measured again by the AGC block. Using this second amplitude measurement result, the M-control block generates a digital M-control signal to the APD bias circuit. In this way, the APD bias voltage (and consequently its multiplication factor) can be adjusted accordingly to a smaller value when the BM-RX receives a very strong incoming burst signal. A DC-offset compensation block sets the balanced signal to keep the amplifier circuit working near the middle of the linear range.
The simplified schematic of the APD bias circuit is shown in Fig. 2(a)
. R1, R2 and nMOSFET M1 form an inverter with the output voltage switching from VCC to , where RON is the on-resistance of the analog switch M1. The output drive stage is an opamp A2 configured as a voltage amplifier with feedback resistors R3 and R4, providing a voltage gain of 1 + R3/R4. Between the inverter and the output drive stage, an amplifier A1 serves as a voltage buffer due to a relatively high output impedance of the inverter. The decoupling design of the APD bias voltage VAPD is now becoming more important because we are varying the APD’s M-factor to increase the linear range of the BM-RX. As shown in Fig. 2(a), the parasitic inductance LB is mainly due to the bonding wire and module lead and the value is usually small. A small capacitance C1 has been integrated inside the APD BM-RX during the module assembly, which can decouple the VAPD properly if only LB is there. Another important but often overlooked, parasitic inductance should be taken into account is the LA, composed of the lead inductance of the output drive stage and the PCB strip inductance. Because APD is a temperature sensitive device, in the design we keep the hot spot, e.g. the output drive stage A2, far away from the APD. The SPICE simulation (Fig. 2(b)) shows that the M-control signal will cause significant ringing on the VAPD when a long PCB trace is present. Therefore, an additional decoupling capacitor CPCB is used to tune out the effect of the LA, and this reduces the settling time of APD’s M-factor considerably.
Fig. 2 (a) Off-chip M-control circuitry for APD biasing, (b) simulated APD bias voltage without and with CPCB.
Inside the BM-RX, the entire amplifier chain was designed for a high linearity (no internal hard decisions) for the whole operating range. After each burst, the linear BM-RX is reset to its highest gain and the APD multiplication factor is restored to the default high value. The simulated total harmonic distortion (THD) as a function of input optical power is shown in Fig. 3
. The THD has been simulated with a pure sine wave with optical power swept from −32dBm to + 0.5dBm (input frequency was 250MHz and extinction ratio was 8dB). The improvement achieved by the M-control scheme (APD M was switched from 6.1 to 2.7, and APD responsivity at M = 1 was 0.8A/W) has been also evaluated with the simulation. In case that the maximum distortion threshold of 10% was assumed, more than 3 dB enhancement for the achievable linear range was found as illustrated in Fig. 3. There are two reasons to schedule the APD M-control after the TIAc core gain adjustment. Firstly, compared to the APD M-switching settling time (~60ns), adjusting TIAc core gain is faster and more predictable in terms of settling time, which simplifies the timing requirement between the fast AGC and the M-control procedure. Secondly, the APD actually behaves as a current gain stage ahead of the TIAc core. Therefore, for sufficiently high burst signal levels, the gain in the later stage (TIAc core in this case) should be reduced before reducing the gain in the earlier stage (APD M-factor) in order to assure a better signal to noise ratio.
3. Experimental setup
The 10Gb/s APD-based linear BM-RX IC was fabricated in a 0.13µm SiGe BiCMOS process. The linear BM-RX IC occupies 1.3x1mm2 and consumes 250mW from a single 2.7V power supply. Figure 4
shows the experimental setup. The reach extender used a single semiconductor optical amplifier (SOA) with a small signal gain of 20dB and a noise figure of 6.2dB. The SOA’s peak gain wavelength was 1290nm and saturation output power was around 10.6dBm. A 10nm coarse wavelength division multiplexing (CWDM) filter was used to remove out-of-band amplified spontaneous emission (ASE) noise from the SOA. The setup also includes 10km + 10km optical fibers in the access and feeder sections respectively. Variable optical attenuators (VOAs) were used to vary the access and feeder budget.
4. Experimental results
The APD-based linear BM-RX was initially characterized in a back-to-back (B2B) configuration without fibers and the reach extender. The 10Gb/s burst consisted of a 150ns preamble of 1010 pattern (including the settling time for APD M-control, linear BM-RX and BM-CDR) and a 1280ns payload. The guard time between consecutive bursts was 51.2ns. Two 1.3µm burst-mode transmitters (BM-TXs) were used to send 10Gb/s upstream bursts: TX#1 consists of a laser externally modulated using an electro-absorption modulator and TX#2 is a DFB laser based TOSA. The power level provided by TX#2 was set at −7dBm at the input of the APD-based linear BM-RX, while only the bit error ratio (BER) of the packet from TX#1 was recorded. Figure 5(a)
plots the measured received burst signals, and self-generated M-control digital signal. As shown in Fig. 5(b), the APD bias voltage VAPD was adjusted between 25.2V (M = 6.1) for weak bursts and 18V (M = 2.7) for strong bursts. The rise and fall time of the APD bias voltage switching was 40ns and 35ns respectively. In this experiment, the bias voltage switching range was chosen conservatively to avoid any possible APD breakdown. In a production-level implementation, an additional control circuit for the APD bias voltage can be used to compensate the temperature shift and therefore a more aggressive switching range can be obtained to further extend the linear range of the BM-RX.
Fig. 5 (a) Incoming burst and M-control waveform (b) APD bias voltage waveform and the corresponding M value.
Figure 6
shows the measured BERs with and without M-control. When M-control is disabled, the measured RX sensitivity was −30.5dBm and the overload was −2.2dBm at a pre forward error correction (FEC) BER of 10−3. After enabling the M-control, the input sensitivity at pre-FEC BER of 10−3 remains unchanged while the measured overload improves to + 0.5dBm. This yields an optical dynamic range of 31dB.
To evaluate the APD linear BM-RX performance in the single SOA-based reach extender configuration, we measured the constant-BER contour over the access and feeder budget plane. Figure 7
shows the measured BER contour at BER = 10−3 with and without M-control. In both cases, a feeder budget of 23dB (or 24.9dB) is allowed while the access budget is within the optical distribution network (ODN) class N2 (or N1) [10]. The total obtainable optical budget in either case is about 54dB (with TX#1 power + 4.4dBm). In addition, the M-control scheme enlarges the admissible area in the access and feeder plane, enabling the possibility for new ODN specifications.
Fig. 7 Measured BER (BER = 10−3) contour with and without M-control for reach extended 10Gb/s upstream.
We finally validated the linearity of the APD linear BM-RX by enabling the electronic dispersion compensation (EDC) in the BM-CDR chip. The EDC consists of 7-stage feed-forward equalization (FFE) and 4-stage decision feedback equalization (DFE) [11]. The EDC tap coefficients were optimized for one burst and then fixed in the burst-mode experiment, as no EDC chip on burst basis was available. M-control has also been enabled in the experiments with EDC. In PON systems, the fiber dispersion for upstream transmission is less of a problem as the standard single-mode fiber has nearly zero dispersion around the 1.3µm wavelength. Instead of compensating the transmission impairments due to the fibers, we used the electronic equalization to compensate the impairments caused by the low bandwidth optical TX at the ONU. This allows for cost-effective components to be used in the ONU for 10Gb/s upstream transmission. As shown in Fig. 8(a)
, an electronic low-pass filter (LPF) was inserted between the RF driver and the EML in TX#1 to emulate a low bandwidth ONU TX. The TX bandwidth has been estimated from its step response. The estimated bandwidths for no filter, with filter A and with filter B cases, are 10, 6.3, and 3GHz respectively. The measured S21 parameter and group delay of the LPFs are shown in Fig. 8(b) and Fig. 8(c) respectively. To emulate a low performance ONU TX, the filter B has been designed with not only a small bandwidth (~3.3GHz), but also a large group delay variation of 523ps within the pass-band (75% of the 3dB bandwidth). Figure 9
shows the measured TX eye diagram and BER = 10−3 contour with linear or limiting-type BM-RX. A BM limiting amplifier (LA) [12] was used with the linear BM-RX to build a limiting-type BM-RX. When the ONU TX had reasonably good output eye-diagram (i.e., 6.3GHz and 10GHz TX cases), the limiting-type and linear BM-RXs achieved similar performance. However, the linear BM-RX and EDC/CDR chip are able to recover the upstream signal with significant inter-symbol interference (ISI), while the limiting-type BM-RX failed to meet the pre-FEC BER threshold for the 3GHz TX case.
Y. F. Chang, “Recent progress of EDC commercialization in addressing datacom and telecom challenges to enable high-speed optical enterprise, metro and long-haul networks,” in Proceedings of Optical Fiber Communication Conference/National Fiber Optic Engineers Conference, OSA Technical Digest (Optical Society of America, 2007), paper NWA2.
X. Yin, J. Put, J. Verbrugghe, J. Gillis, X.-Z. Qiu, J. Bauwelinck, J. Vandewege, H.-G. Krimmel, and M. Achouche, “A 10Gb/s burst-mode TIA with on-chip reset/lock CM signaling detection and limiting amplifier with a 75ns settling time,” in Proceedings of Solid-State Circuits Conference Digest of Technical Papers (ISSCC), (2012), paper 24.4.
5. Conclusions
We have demonstrated for the first time a 10Gb/s APD-based linear BM-RX for reach-extended PON systems. Using an on-chip self-generated M-control signal, it achieved 31dB dynamic range. In conjunction with an EDC/CDR chip, the APD linear BM-RX with a wide dynamic range of 31dB enables flexible network configurations and relaxes the performance requirements on low-cost ONU optical components.
Acknowledgments
The authors thank the EU-funded FP7 ICT projects EURO-FOS, Agency for Innovation byScience and Technology in Flanders (IWT), and Sumitomo Electric Devices Innovations, Inc for providing EML and APD-TIA ROSA assembly.
References and links
N. Yoshimoto, “Recent R&D trends in broadband optical access system technologies towards the second-generation FTTH era in Japan,” in Proceedings of Progress in Electromagnetics Research Symposium, (Marrakesh, Morocco, 2011), pp. 520–523. | |
B. Zhu, D. Au, F. Khan, and Y. Li, “1:n 10G-PON overlay of GPON link using bidirectional Raman amplifier,” in Proceedings of European Conference Optical Communication, (2012), Paper Tu.1.B.1. | |
S. Ihara, S. Yoshima, D. Mita, M. Noda, M. Nogami, and J. Nakagawa, “Over 60km transmission extended reach 10G-EPON system with a wide 29dB dynamic range burst-mode receiver,” in Proceedings of European Conference Optical Communication, (2012), Paper Tu.1.B.4. | |
H. Bulow, “Electronic equalization of transmission impairments,” in Proceedings of Optical Fiber Communication Conference and Exhibit (Optical Society of America, 2002), pp. 24–25, Anaheim, Calif, USA. | |
P. Ossieur, N. A. Quadir, S. Porto, M. Rensing, C. Antony, W. Han, P. O. Brien, Y. Chang, and P. D. Townsend, “A 10G linear BMRX supporting electronic dispersion compensation for extended-reach optical links,” in Proceedings of European Conference Optical Communication, (2011), Paper Th.13.B.4. | |
P. Ossieur, N. A. Quadir, S. Porto, M. Rensing, C. Antony, P. O’Brien, Y. Frank) Chang, and P. D. Townsend, “A 10G linear burst-mode receiver supporting electronic dispersion compensation for extended-reach optical links,” Opt. Express 19(26), 604 (2011). | |
T. Nakanishi, Y. Fukuda, K. Suzuki, N. Yoshimoto, M. Nakamura, K. Kato, K. Nishimura, Y. Ohtomo, and M. Tsubokawa, “Wide dynamic range and high sensitivity APD burst receiver configuration based on M-switching technique for 10GEPON system,” in Proceedings of Lasers and Electro-Optics Society (Institute of Electrical and Electronics Engineers, 2007), Paper ThW5. | |
X. Yin, X. Z. Qiu, J. Gillis, J. Put, J. Verbrugghe, J. Bauwelinck, J. Vandewege, H. Krimmel, D. van Veen, P. Vetter, and F. Chang, “Experiments on 10Gb/s fast settling high sensitivity burst-mode receiver with on-chip auto-reset for 10G-GPONs [Invited],” J. Opt. Commun. Netw. 4(11), B68–B76 (2012). [CrossRef] | |
X. Yin, B. Moeneclaey, X. Z. Qiu, J. Verbrugghe, K. Verheyen, J. Bauwelinck, J. Vandewege, M. Achouche, and F. Y. Chang, “A 10Gb/s APD-based linear burst-mode receiver with 31dB dynamic range for reach-extended PON systems,” in Proceedings of European Conference Optical Communication, (2012), Paper Tu.1.B.5. | |
“ITU-T Recommendation G.987.2: 10-Gigabit-capable passive optical networks (XG-PON): Physical media dependent (PMD) layer specification,” (ITU-T, 2010). | |
Y. F. Chang, “Recent progress of EDC commercialization in addressing datacom and telecom challenges to enable high-speed optical enterprise, metro and long-haul networks,” in Proceedings of Optical Fiber Communication Conference/National Fiber Optic Engineers Conference, OSA Technical Digest (Optical Society of America, 2007), paper NWA2. | |
X. Yin, J. Put, J. Verbrugghe, J. Gillis, X.-Z. Qiu, J. Bauwelinck, J. Vandewege, H.-G. Krimmel, and M. Achouche, “A 10Gb/s burst-mode TIA with on-chip reset/lock CM signaling detection and limiting amplifier with a 75ns settling time,” in Proceedings of Solid-State Circuits Conference Digest of Technical Papers (ISSCC), (2012), paper 24.4. |
OCIS Codes
(060.0060) Fiber optics and optical communications : Fiber optics and optical communications
(060.2360) Fiber optics and optical communications : Fiber optics links and subsystems
ToC Category:
Access Networks and LAN
History
Original Manuscript: October 1, 2012
Revised Manuscript: November 22, 2012
Manuscript Accepted: November 23, 2012
Published: December 3, 2012
Virtual Issues
European Conference on Optical Communication 2012 (2012) Optics Express
Citation
Xin Yin, Bart Moeneclaey, Xing-Zhi Qiu, Jochen Verbrugghe, Koen Verheyen, Johan Bauwelinck, Jan Vandewege, Mohand Achouche, and Y. Chang, "A 10Gb/s APD-based linear burst-mode receiver with 31dB dynamic range for reach-extended PON systems," Opt. Express 20, B462-B469 (2012)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-20-26-B462
Sort: Year | Journal | Reset
References
- N. Yoshimoto, “Recent R&D trends in broadband optical access system technologies towards the second-generation FTTH era in Japan,” in Proceedings of Progress in Electromagnetics Research Symposium, (Marrakesh, Morocco, 2011), pp. 520–523.
- B. Zhu, D. Au, F. Khan, and Y. Li, “1:n 10G-PON overlay of GPON link using bidirectional Raman amplifier,” in Proceedings of European Conference Optical Communication, (2012), Paper Tu.1.B.1.
- S. Ihara, S. Yoshima, D. Mita, M. Noda, M. Nogami, and J. Nakagawa, “Over 60km transmission extended reach 10G-EPON system with a wide 29dB dynamic range burst-mode receiver,” in Proceedings of European Conference Optical Communication, (2012), Paper Tu.1.B.4.
- H. Bulow, “Electronic equalization of transmission impairments,” in Proceedings of Optical Fiber Communication Conference and Exhibit (Optical Society of America, 2002), pp. 24–25, Anaheim, Calif, USA.
- P. Ossieur, N. A. Quadir, S. Porto, M. Rensing, C. Antony, W. Han, P. O. Brien, Y. Chang, and P. D. Townsend, “A 10G linear BMRX supporting electronic dispersion compensation for extended-reach optical links,” in Proceedings of European Conference Optical Communication, (2011), Paper Th.13.B.4.
- P. Ossieur, N. A. Quadir, S. Porto, M. Rensing, C. Antony, P. O’Brien, Y. Frank) Chang, and P. D. Townsend, “A 10G linear burst-mode receiver supporting electronic dispersion compensation for extended-reach optical links,” Opt. Express19(26), 604 (2011).
- T. Nakanishi, Y. Fukuda, K. Suzuki, N. Yoshimoto, M. Nakamura, K. Kato, K. Nishimura, Y. Ohtomo, and M. Tsubokawa, “Wide dynamic range and high sensitivity APD burst receiver configuration based on M-switching technique for 10GEPON system,” in Proceedings of Lasers and Electro-Optics Society (Institute of Electrical and Electronics Engineers, 2007), Paper ThW5.
- X. Yin, X. Z. Qiu, J. Gillis, J. Put, J. Verbrugghe, J. Bauwelinck, J. Vandewege, H. Krimmel, D. van Veen, P. Vetter, and F. Chang, “Experiments on 10Gb/s fast settling high sensitivity burst-mode receiver with on-chip auto-reset for 10G-GPONs [Invited],” J. Opt. Commun. Netw.4(11), B68–B76 (2012). [CrossRef]
- X. Yin, B. Moeneclaey, X. Z. Qiu, J. Verbrugghe, K. Verheyen, J. Bauwelinck, J. Vandewege, M. Achouche, and F. Y. Chang, “A 10Gb/s APD-based linear burst-mode receiver with 31dB dynamic range for reach-extended PON systems,” in Proceedings of European Conference Optical Communication, (2012), Paper Tu.1.B.5.
- “ITU-T Recommendation G.987.2: 10-Gigabit-capable passive optical networks (XG-PON): Physical media dependent (PMD) layer specification,” (ITU-T, 2010).
- Y. F. Chang, “Recent progress of EDC commercialization in addressing datacom and telecom challenges to enable high-speed optical enterprise, metro and long-haul networks,” in Proceedings of Optical Fiber Communication Conference/National Fiber Optic Engineers Conference, OSA Technical Digest (Optical Society of America, 2007), paper NWA2.
- X. Yin, J. Put, J. Verbrugghe, J. Gillis, X.-Z. Qiu, J. Bauwelinck, J. Vandewege, H.-G. Krimmel, and M. Achouche, “A 10Gb/s burst-mode TIA with on-chip reset/lock CM signaling detection and limiting amplifier with a 75ns settling time,” in Proceedings of Solid-State Circuits Conference Digest of Technical Papers (ISSCC), (2012), paper 24.4.
Cited By |
 Alert me when this paper is cited |
OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.
« Previous Article | Next Article »
OSA is a member of 