Laser emission from a solar-pumped fiber

doi:10.1364/OE.20.005891

« Show journal navigation

Laser emission from a solar-pumped fiber

Shintaro Mizuno, Hiroshi Ito, Kazuo Hasegawa, Takenobu Suzuki, and Yasutake Ohishi »View Author Affiliations

Optics Express, Vol. 20, Issue 6, pp. 5891-5895 (2012)
http://dx.doi.org/10.1364/OE.20.005891

View Full Text Article

Acrobat PDF (960 KB)

Journal Search
Article Lookup

Article Tools

Citations

Alert me when this article is cited
Export Citation/Save

Article Navigation

▸ Article Outline
– Abstract
1. Introduction
2. Solar-pumped fiber laser system setup
3. Results and discussion
– References and links

Article Tools
Full Text
Article Info
References
Cited By
Figures
Metrics
Download PDF

Viewing Equations in the
HTML Article

Optimal Viewing Recommendations

Full Text
Article Info
References (15)
Cited By
Figures (3)
Metrics

Abstract

We report the realization of a solar-pumped fiber laser (SPFL) using a double-clad (a center core/ an inner clad working also as optical waveguide/ an outer clad) Nd-doped fluoride optical fiber as a laser medium. With a compact off-axis parabolic mirror of 5 cm in aperture diameter, the natural sunlight is concentrated by a factor 10⁴, and introduced partly into the core of the fiber and partly into the inner clad in which the light is guided in some distance and transferred to the core after all. We have obtained clear laser spectrum characteristics with approximately 0.01 nm full-width-half-maximum of the laser line at the peak wavelength of 1053.7 nm, a low-lasing threshold of 49.1 mW, a slope efficiency of 6.6%, and a total efficiency of 1.76%. Further optimization of the medium properties, optical cavity, and concentration technique will yield higher efficiency and lower threshold.

1. Introduction

A solar-pumped laser (SPL) is an optical device that converts incoherent sunlight with a wide spread of spectrum and low areal energy density into a monochromatic coherent light beam. SPLs are expected to be promising core devices in such technologies as satellite communications, space debris management, sunlight energy transmission from space, and energy cycling by converting sunlight to chemical energy [1

C. G. Young, “A sun-pumped cw one-watt laser,” Appl. Opt. 5(6), 993–997 (1966). [CrossRef] [PubMed]

–3

T. Yabe, B. Bagheri, T. Ohkubo, S. Uchida, M. Yoshida, T. Funatsu, T. Oishi, K. Daito, M. Ishioka, N. Yasunaga, Y. Sato, C. Baasandash, Y. Okamoto, and K. Yanagitani, “100 W-class solar pumped laser for sustainable magnesium-hydrogen energy cycle,” J. Appl. Phys. 104(8), 083104 (2008). [CrossRef]

]. After the first reports on solar-pumped laser based on a Dy²⁺:CaF₂ crystal system [4

Z. J. Kiss, H. R. Lewis, and R. C. Duncan, “Sun pumped continuous optical maser,” Appl. Phys. Lett. 2(5), 93–94 (1963). [CrossRef]

–10

K. Ueda, A. Liu, K. Kametani, and M. Kamamura, “Possibility of solar-pumped fiber lasers,” IEEJ OQD-97–19, 13 (1997).

] in 1963, several improvements have been reported. More recently, for the lasing medium, transparent co-doped (Nd,Cr) YAG ceramics have been popularly investigated where Cr³⁺ sensitises Nd³⁺ ion emissions. A conversion efficiency from solar energy after corrector to laser energy was reported as 4.3% with a 9% slope efficiency, which are the best efficiencies obtained so far using (Cr³⁺,Nd³⁺):YAG ceramics [9

T. Ohkubo, T. Yabe, K. Yoshida, S. Uchida, T. Funatsu, B. Bagheri, T. Oishi, K. Daito, M. Ishioka, Y. Nakayama, N. Yasunaga, K. Kido, Y. Sato, C. Baasandash, K. Kato, T. Yanagitani, and Y. Okamoto, “Solar-pumped 80 W laser irradiated by a Fresnel lens,” Opt. Lett. 34(2), 175–177 (2009). [CrossRef] [PubMed]

]. Laser efficiency, cooling systems, and beam quality, however, still remain challenging issues. A solar-pumped fiber laser has been proposed [10

K. Ueda, A. Liu, K. Kametani, and M. Kamamura, “Possibility of solar-pumped fiber lasers,” IEEJ OQD-97–19, 13 (1997).

] in 1997. After that one pumped by halogen lamp has been demonstrated [11

T. Saiki, K. Imasaki, S. Motokoshi, S. Uchida, H. Fujita, M. Nakatsuka, Y. Izawa, M. Yoshida, H. Ito, and C. Yamanaka, “Solar-pumped Nd dope multimode-fiber laser with a D-shaped large clad under quasi-solar-pumping,” Rev. Laser Eng. 32(1), 48–53 (2004). [CrossRef]

], but not by natural sunlight. There are substantial differences between natural and simulated-sunlight in spectra, intensities, and concentration techniques. By overcoming these differences, we addressed the ultimate objective, that is, realization of fiber lasing under natural sunlight pumping. In this paper, we report the realization of a solar-pumped fiber laser (SPFL) operating under natural sunlight using a Nd-doped fluoride optical fiber.

2. Solar-pumped fiber laser system setup

Figure 1 shows a schematic diagram of the solar-pumped fiber laser system investigated. Intense sunlight is necessary because laser properties, such as slope efficiency and lasing threshold, are strongly dependent on excitation power density achieved in the laser medium rather than total amount of pump power. To increase power densities, the concentration ratio C of an optical concentrator must be increased. For sunlight, we have

C = {(\frac{R o r T \times \sin θ_{f}}{\sin θ_{s u n}})}^{2}

(1)

where R and T are the respective reflectance and transmittance of the concentration optics, sinθ_f is the numerical aperture (NA) of the optical concentrator, θ_sun is the half view angle of the sun from earth, and sinθ_sun depends on the solar radius and the average distance between earth and sun. For solar light, C is determined by NA and R or T of the focusing optics. We selected an off-axis parabolic mirror because it is free from chromatic aberration and provides a relatively high NA with high reflectivity in the visible range. With NA of 0.5 and R of 0.92, C is 10626. A diameter of the parabolic mirror is 50 mm.

Fig. 1 Schematic set-up of the solar-pumped fiber laser experiment. L, lens; LPF, long-pass filter; MMF, multi-mode fiber; OAPM, off-axis parabolic mirror; PM, power meter; SA, spectrum analyzer; ZBLAN-DCF, ZBLAN double-clad fiber.

The accompanying temperature increase in the laser medium as C increases produces changes in lasing properties. Generally, beam quality and laser efficiency deteriorate; at worst thermal stress destroys the lasing medium. Heat has its origins in (1) the quantum defect, i.e., the energy difference between excitation photon and lasing photon, and (2) absorption losses in the laser medium. Whereas (2) can be reduced by improving the material, (1) cannot be reduced in principle. The lasing wavelength λ_L and energy conversion efficiency η are related as follows:

η = \frac{\int_{λ_{s}}^{λ_{L}} \frac{λ_{i}}{λ_{L}} I (λ_{i}) d λ_{i}}{\int_{λ_{s}}^{λ_{e}} I (λ_{i}) d λ_{i}}

(2)

where λ_s and λ_e are the shortest and longest wavelengths representing the absorption range of the medium, respectively. For a Nd³⁺-doped Y₃Al₅O₁₂ crystal, often used as the medium in solar-pumped rod lasers, the theoretical upper limit for solar energy conversion efficiency at a wavelength of 1.06 μm is calculated to be 48%. The remaining energy generates heat within the medium, which needs cooling so as not to cause a decrease in a figure of merit of the laser medium which is the product of the excited state lifetime and the stimulated emission cross section of active ion. To date, there are no reports of a continuous wave solar-pumped laser without an active cooling system. Efficient cooling under a constant volume is brought about by sufficient specific surface area. The efficient cooling can be realized by either disk-like or fiber-like shape of medium. Given the shape, we need to consider the absorbance of the medium over a wide range of wavelengths. A fiber-type is able to absorb almost all excitation light propagating along its axial direction because of the long optical path. In contrast, a disk-type medium cannot absorb same amount of excitation sunlight because of its extremely short interaction length. For this reason, a fiber-type medium is more suitable for our purposes.

Directing all excitation light into the core is challenging because its size for a single-mode fiber is smaller than the smallest solar image capable of being provided by typical optical mirrors or lenses. A diameter of the sun image at the focal point using an off-axis parabolic mirror is about 0.5 mm. The double-clad structure of core, inner cladding, and outer cladding for a SPFL is considered adequate to absorb excitation sunlight efficiently, where the active ions in the core absorbs the light propagating in the inner cladding. Almost all sunlight captured ultimately contributes to the activation of core ions. Overall, the fiber-type shape with the double-clad structure gives a medium configuration satisfactory for use in the solar-pumped laser.

Glass materials subject to sunlight excitation have not been studied before. We reported that Nd-doped ZBLAN glass showed high quantum efficiencies for emission [12

T. Suzuki, H. Kawai, H. Nasu, S. Mizuno, H. Ito, K. Hasegawa, and Y. Ohishi, “Spectroscopic investigation of Nd³⁺-doped ZBLAN glass for solar-pumped lasers,” J. Opt. Soc. Am. B 28, 2001–2006 (2011). [CrossRef]

, 13

T. Suzuki, H. Kawai, H. Nasu, M. Hughes, S. Mizuno, K. Hasegawa, H. Ito, and Y. Ohishi, “Excitation wavelength dependence of quantum efficiencies of Nd-doped glasses for solar pumped fiber lasers,” Proc. SPIE 7598, 75981L, 75981L-8 (2010). [CrossRef]

]. Using the Judd-Ofelt analysis, the stimulated emission cross-section σ in the transition ⁴F_3/2 → ⁴I_11/2 for Nd³⁺ doped in ZBLAN glass was calculated to be σ = 2.95 × 10⁻²⁰ cm² for glass with a dopant concentration 0.5 mol. %. With a fluorescence lifetime τ = 496 μsec for glass, the quantity important to lasing and inversely proportional to the lasing threshold takes the value στ = 1.45 × 10⁻²³cm²sec, which is much higher than στ = 0.75 x10⁻²³cm²sec for Nd-doped silica glass co-doped with Al [14

K. Arai, H. Namikawa, K. Kumata, T. Honda, Y. Ishii, and T. Hanada, “Aluminum or phosphorus co-doping effects on the fluorescence and structural properties of neodymium-doped silica glass,” J. Appl. Phys. 59(10), 3430–3436 (1986). [CrossRef]

]. We constructed the SPFL resonator from Nd-doped ZBLAN double-clad fiber with a mode field diameter about 5 μm, an inner cladding diameter 125 μm and a cladding numerical aperture 0.5, and reflecting mirrors of 98.0% at 1050 nm.

3. Results and discussion

Lasing experiments by sunlight were performed at longitude 137°3′E and latitude 35°10′8”N under clear skies with the occasional cumuli. Figure 2(a) shows the spectra of sunlight before and after passing through the Nd-doped ZBLAN fiber. Direct solar radiation spectra are calculated by Bird’s model [15

R. E. Bird and C. Riordan, “Simple solar spectral model for direct and diffuse irradiance on horizontal and tilted planes at the Earth's surface for cloudless atmospheres,” J. Clim. Appl. Meteorol. 25(1), 87–97 (1986). [CrossRef]

]. A calculation condition is as shown below. (1) elevation angle is 37°, (2) aerosol optical depth at the wavelength of 500 nm is 0.27, (3) total column ozone is 0.34 cm, (4) surface albedo is 0.20, (5) total perceptible vapor water is 1.42 cm, (6) 137° 3′ east in longitude, and (7) 35° 10′ north in latitude. (1)-(4) are followed standard condition values of ISO and JIS and (5)-(7) are local values.

Fig. 2 Solar-pumped fiber laser spectra (a) the spectra of sunlight before and after passing through the Nd-doped ZBLAN fiber (b) the lasing spectra obtained at different times

Absorption bands of the Nd³⁺ dopant are observed. Sunlight was completely absorbed around the bands at wavelengths of 520, 575, 740, 795 and 867 nm. In contrast, we observed strong intensity transmissions of blue light with a wavelength from 410 to 510 nm, red light from 590 nm to 725 nm, and near-infrared light from 890 nm up to the lasing wavelength. The absorbed sunlight power was 56%. Detailed in Fig. 2(b) are lasing spectra obtained at different times showing complex, congested features that vary considerably, partly because of inhomogeneous broadening from Nd ions in glass and longitudinal-mode hopping. All spectra obtained show a peak around the 1053 nm wavelength; many laser line peaks between 1052 and 1054 nm are observed. In one example, the full-width-half-maximum of the laser line at the peak wavelength of 1053.7 nm is approximately 0.01 nm.

Figure 3 plots SPFL output power versus input sunlight power captured in the inner cladding of the fiber. The input sunlight power is controlled by changing the opening ratio of a slit located in front of the parabolic mirror. A clear lasing threshold at 49.1 mW is confirmed by natural sunlight excitation. The total efficiency was 0.88%. The maximum laser output power was 0.57 mW. By fabricating a bundled structure of fibers, a higher output power will be achieved. The slope efficiency of a single side output above threshold was 3.3%. Because the reflectivity of both ends of the fiber is the same, the output power from the other side is estimated to be equivalent, thereby doubling the slope efficiency and total efficiency to 6.6% and to 1.76%, respectively. The ratio E of the sunlight power within the wavelength range of the Nd absorption bands to that over the range 350 nm to 4000 nm is expressed as

E = \frac{\int_{350}^{λ_{L}} a \cdot I (λ) d λ}{\int_{350}^{4000} I (λ) d λ}

(3)

where λ_L is the lasing wavelength of 1.05 μm, I(λ) is the spectral intensity per unit wavelength, and ‘a’ equals 1 for wavelengths in the Nd absorption bands, otherwise 0. The air mass 1.5 (AM 1.5) spectrum and the absorption spectrum of Nd-doped ZBLAN glass yield E of about 44%. The theoretical limit of the slope efficiency, i.e., the theoretical energy conversion efficiency including quantum defects from the parts of AM 1.5 spectrum corresponding to Nd absorption bands to the lasing wavelength of 1.05 μm, was calculated as 14.0%. The reasons for the lower value of slope efficiency compared to the theoretical one are (1) high mirror reflectivity, i.e., a laser light confinement that is too high, (2) low absorption efficiency of excitation sunlight, and (3) losses in the laser cavity by the mirrors and fiber.

Fig. 3 Solar-pumped fiber laser output power as a function of the input solar power.

In conclusion, we have demonstrated the operation of a solar-pumped fiber laser (SPFL) using highly concentrated natural sunlight and a Nd-doped fluoride optical fiber. With threshold of 49.1 mW, we estimated the total slope efficiency at 6.6% and the total efficiency at 1.76%. The realization of SPFL using double-clad single mode fiber overcame challenges concerning beam quality, cooling, and energy conversion efficiency. Moreover, this opens the way for compact solar-pumped lasers that contrasts with those large-scale and high-power systems previously reported. Further research for sensitisers besides Nd active over the absorption bands will lead to an improved use of sunlight. Optimization of the laser medium properties, optical cavity and concentration technique will lead to higher efficiencies and lower thresholds as well.

Acknowledgments

This work was supported in part by the Japanese Ministry of Culture, Sports, and Education (MEXT) Support Program for Forming Strategic Research Infrastructure (2011–2015).

References and links

1.	C. G. Young, “A sun-pumped cw one-watt laser,” Appl. Opt. 5(6), 993–997 (1966). [CrossRef] [PubMed]
2.	R. J. De Young, “Beam profile measurement of a solar-pumped iodine laser,” Appl. Opt. 25(21), 3850–3854 (1986). [CrossRef] [PubMed]
3.	T. Yabe, B. Bagheri, T. Ohkubo, S. Uchida, M. Yoshida, T. Funatsu, T. Oishi, K. Daito, M. Ishioka, N. Yasunaga, Y. Sato, C. Baasandash, Y. Okamoto, and K. Yanagitani, “100 W-class solar pumped laser for sustainable magnesium-hydrogen energy cycle,” J. Appl. Phys. 104(8), 083104 (2008). [CrossRef]
4.	Z. J. Kiss, H. R. Lewis, and R. C. Duncan, “Sun pumped continuous optical maser,” Appl. Phys. Lett. 2(5), 93–94 (1963). [CrossRef]
5.	G. R. Simpson, “Continuous sun-pumped room temperature glass laser operation,” Appl. Opt. 3(6), 783 (1964). [CrossRef]
6.	H. Arashi, Y. Oka, N. Sasahara, A. Kaimai, and M. Ishigame, “A solar-pumped cw 18 W Nd:YAG laser,” Jpn. J. Appl. Phys. 23(Part 1, No. 8), 1051–1053 (1984). [CrossRef]
7.	H. Arashi and Y. Kaneda, “Solar-pumped laser and its second harmonic generation,” Sol. Energy 50(5), 447–451 (1993). [CrossRef]
8.	R. M. J. Benmair, J. Kagan, Y. Kalisky, Y. Noter, M. Oron, Y. Shimony, and A. Yogev, “Solar-pumped Er,Tm,Ho:YAG laser,” Opt. Lett. 15(1), 36–38 (1990). [CrossRef] [PubMed]
9.	T. Ohkubo, T. Yabe, K. Yoshida, S. Uchida, T. Funatsu, B. Bagheri, T. Oishi, K. Daito, M. Ishioka, Y. Nakayama, N. Yasunaga, K. Kido, Y. Sato, C. Baasandash, K. Kato, T. Yanagitani, and Y. Okamoto, “Solar-pumped 80 W laser irradiated by a Fresnel lens,” Opt. Lett. 34(2), 175–177 (2009). [CrossRef] [PubMed]
10.	K. Ueda, A. Liu, K. Kametani, and M. Kamamura, “Possibility of solar-pumped fiber lasers,” IEEJ OQD-97–19, 13 (1997).
11.	T. Saiki, K. Imasaki, S. Motokoshi, S. Uchida, H. Fujita, M. Nakatsuka, Y. Izawa, M. Yoshida, H. Ito, and C. Yamanaka, “Solar-pumped Nd dope multimode-fiber laser with a D-shaped large clad under quasi-solar-pumping,” Rev. Laser Eng. 32(1), 48–53 (2004). [CrossRef]
12.	T. Suzuki, H. Kawai, H. Nasu, S. Mizuno, H. Ito, K. Hasegawa, and Y. Ohishi, “Spectroscopic investigation of Nd³⁺-doped ZBLAN glass for solar-pumped lasers,” J. Opt. Soc. Am. B 28, 2001–2006 (2011). [CrossRef]
13.	T. Suzuki, H. Kawai, H. Nasu, M. Hughes, S. Mizuno, K. Hasegawa, H. Ito, and Y. Ohishi, “Excitation wavelength dependence of quantum efficiencies of Nd-doped glasses for solar pumped fiber lasers,” Proc. SPIE 7598, 75981L, 75981L-8 (2010). [CrossRef]
14.	K. Arai, H. Namikawa, K. Kumata, T. Honda, Y. Ishii, and T. Hanada, “Aluminum or phosphorus co-doping effects on the fluorescence and structural properties of neodymium-doped silica glass,” J. Appl. Phys. 59(10), 3430–3436 (1986). [CrossRef]
15.	R. E. Bird and C. Riordan, “Simple solar spectral model for direct and diffuse irradiance on horizontal and tilted planes at the Earth's surface for cloudless atmospheres,” J. Clim. Appl. Meteorol. 25(1), 87–97 (1986). [CrossRef]

OCIS Codes
(060.2320) Fiber optics and optical communications : Fiber optics amplifiers and oscillators
(140.3530) Lasers and laser optics : Lasers, neodymium
(350.6050) Other areas of optics : Solar energy

ToC Category:
Lasers and Laser Optics

History
Original Manuscript: December 2, 2011
Revised Manuscript: February 7, 2012
Manuscript Accepted: February 10, 2012
Published: February 27, 2012

Citation
Shintaro Mizuno, Hiroshi Ito, Kazuo Hasegawa, Takenobu Suzuki, and Yasutake Ohishi, "Laser emission from a solar-pumped fiber," Opt. Express 20, 5891-5895 (2012)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-20-6-5891

Sort: Author | Year | Journal | Reset

References

C. G. Young, “A sun-pumped cw one-watt laser,” Appl. Opt.5(6), 993–997 (1966). [CrossRef] [PubMed]
R. J. De Young, “Beam profile measurement of a solar-pumped iodine laser,” Appl. Opt.25(21), 3850–3854 (1986). [CrossRef] [PubMed]
T. Yabe, B. Bagheri, T. Ohkubo, S. Uchida, M. Yoshida, T. Funatsu, T. Oishi, K. Daito, M. Ishioka, N. Yasunaga, Y. Sato, C. Baasandash, Y. Okamoto, and K. Yanagitani, “100 W-class solar pumped laser for sustainable magnesium-hydrogen energy cycle,” J. Appl. Phys.104(8), 083104 (2008). [CrossRef]
Z. J. Kiss, H. R. Lewis, and R. C. Duncan, “Sun pumped continuous optical maser,” Appl. Phys. Lett.2(5), 93–94 (1963). [CrossRef]
G. R. Simpson, “Continuous sun-pumped room temperature glass laser operation,” Appl. Opt.3(6), 783 (1964). [CrossRef]
H. Arashi, Y. Oka, N. Sasahara, A. Kaimai, and M. Ishigame, “A solar-pumped cw 18 W Nd:YAG laser,” Jpn. J. Appl. Phys.23(Part 1, No. 8), 1051–1053 (1984). [CrossRef]
H. Arashi and Y. Kaneda, “Solar-pumped laser and its second harmonic generation,” Sol. Energy50(5), 447–451 (1993). [CrossRef]
R. M. J. Benmair, J. Kagan, Y. Kalisky, Y. Noter, M. Oron, Y. Shimony, and A. Yogev, “Solar-pumped Er,Tm,Ho:YAG laser,” Opt. Lett.15(1), 36–38 (1990). [CrossRef] [PubMed]
T. Ohkubo, T. Yabe, K. Yoshida, S. Uchida, T. Funatsu, B. Bagheri, T. Oishi, K. Daito, M. Ishioka, Y. Nakayama, N. Yasunaga, K. Kido, Y. Sato, C. Baasandash, K. Kato, T. Yanagitani, and Y. Okamoto, “Solar-pumped 80 W laser irradiated by a Fresnel lens,” Opt. Lett.34(2), 175–177 (2009). [CrossRef] [PubMed]
K. Ueda, A. Liu, K. Kametani, and M. Kamamura, “Possibility of solar-pumped fiber lasers,” IEEJOQD-97–19, 13 (1997).
T. Saiki, K. Imasaki, S. Motokoshi, S. Uchida, H. Fujita, M. Nakatsuka, Y. Izawa, M. Yoshida, H. Ito, and C. Yamanaka, “Solar-pumped Nd dope multimode-fiber laser with a D-shaped large clad under quasi-solar-pumping,” Rev. Laser Eng.32(1), 48–53 (2004). [CrossRef]
T. Suzuki, H. Kawai, H. Nasu, S. Mizuno, H. Ito, K. Hasegawa, and Y. Ohishi, “Spectroscopic investigation of Nd3+-doped ZBLAN glass for solar-pumped lasers,” J. Opt. Soc. Am. B28, 2001–2006 (2011). [CrossRef]
T. Suzuki, H. Kawai, H. Nasu, M. Hughes, S. Mizuno, K. Hasegawa, H. Ito, and Y. Ohishi, “Excitation wavelength dependence of quantum efficiencies of Nd-doped glasses for solar pumped fiber lasers,” Proc. SPIE7598, 75981L, 75981L-8 (2010). [CrossRef]
K. Arai, H. Namikawa, K. Kumata, T. Honda, Y. Ishii, and T. Hanada, “Aluminum or phosphorus co-doping effects on the fluorescence and structural properties of neodymium-doped silica glass,” J. Appl. Phys.59(10), 3430–3436 (1986). [CrossRef]
R. E. Bird and C. Riordan, “Simple solar spectral model for direct and diffuse irradiance on horizontal and tilted planes at the Earth's surface for cloudless atmospheres,” J. Clim. Appl. Meteorol.25(1), 87–97 (1986). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Click here to see a list of articles that cite this paper