OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 20, Iss. 6 — Mar. 12, 2012
  • pp: 6448–6455
« Show journal navigation

Enhancement of electro-optic properties in liquid crystal devices via titanium nanoparticle doping

Yong-Seok Ha, Hyung-Jun Kim, Hong-Gyu Park, and Dae-Shik Seo  »View Author Affiliations


Optics Express, Vol. 20, Issue 6, pp. 6448-6455 (2012)
http://dx.doi.org/10.1364/OE.20.006448


View Full Text Article

Acrobat PDF (1617 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We investigated the properties of nematic liquid crystal device (NLC) doped with titanium (Ti) nanoparticle (~100nm). The electro-optic (EO) properties of LCs changed according to Ti nanoparticle doping concentration. Ti nanoparticles in the NLC cells focused the electric field flux and strengthened the electric field. Further, Ti nanoparticles in NLC molecules may trap charged ionic impurities and suppress the screen effect, leading to a stronger electric field and the van der Waals dispersion interactions between NLC molecules and the alignment layers. We also simulated the boundary conditions of the Ti nanoparticles in the electric field using Ansoft Maxwell software. Our experimental results agreed with the phenomenon predicted by software simulation based on general physical theory. Synthetically, at a 1.0 wt. % Ti nanoparticle doping concentration, the NLC cells showed the best EO properties, such as a low threshold voltage (1.25V), fast response time (13.2ms), and low pretilt angle (3.90°).

© 2012 OSA

1. Introduction

Liquid crystal (LC) alignment methods and alignment materials have been extensively studied to fabricate high-quality liquid crystal devices (LCDs). However, these methods are rather more difficult than conventional methods due to additional complicated processing and equipment [1

1. H. G. Park, J. J. Lee, K. Y. Dong, B. Y. Oh, Y. H. Kim, H. Y. Jeong, B. K. Ju, and D. S. Seo, “Homeotropic alignment of liquid crystals on a nano-patterned polyimide surface using nanoimprint lithography,” Soft Matter 7(12), 5610–5614 (2011). [CrossRef]

]. In recent years, nanoparticle (NP) doping with LCs has been actively studied for enhancing LC properties, because NP doping with LCs is easier than other methods and can be applicable in the conventional process.

A variety of NPs in LCs have been investigated. Ferroelectric particles were used for increasing the dielectric anisotropy [2

2. A. Glushchenko, C. I. Cheon, J. West, F. Li, E. Büyüktanir, Y. Reznikov, and A. Buchnev, “Ferroelectric particles in liquid crystals: recent frontiers,” Mol. Cryst. Liq. Cryst. (Phila. Pa.) 453(1), 227–237 (2006). [CrossRef]

, 3

3. O. Kurochkin, O. Buchnev, A. Iljin, S. K. Park, S. B. Kwon, O. Grabar, and Y. Reznikov, “A colloid of ferroelectric nanoparticles in a cholesteric liquid crystal,” J. Opt. A, Pure Appl. Opt. 11(2), 024003 (2009). [CrossRef]

]. NPs of metals such as Au [4

4. K. K. Vardanyan, R. D. Walton, and D. M. Bubb, “Liquid crystal composites with a high percentage of gold nanoparticles,” Liq. Cryst. 38(10), 1279–1287 (2011). [CrossRef]

] and Ag [5

5. G. Zhang, X. Chen, J. Zhao, Y. Chai, W. Zhuang, and L. Wang, “Electrophoretic deposition of silver nanoparticles in lamellar lyotropic liquid crystal,” Mater. Lett. 60(23), 2889–2892 (2006). [CrossRef]

] change the elastic parameter and the rotational viscosity of LCs. For suppressing the screen effect, ZrO2 oxide particles were doped with LCs [6

6. H. J. Kim, Y. G. Kang, H. G. Park, K. M. Lee, S. Yang, H. Y. Jung, and D. S. Seo, “Effects of the dispersion of zirconium dioxide nanoparticles on high performance electro-optic properties in liquid crystal devices,” Liq. Cryst. 38(7), 871–875 (2011). [CrossRef]

], and carbon nano-tubes (CNTs) were doped into the alignment layer [7

7. W. K. Lee, Y. S. Choi, Y. G. Kang, J. W. Sung, D. S. Seo, and C. M. Park, “Super-fast switching of twisted nematic liquid crystals on 2D single wall carbon nanotube networks,” Adv. Funct. Mater. 21(20), 3843–3850 (2011). [CrossRef]

]. CNTs in LCs make LCs mixture operate more rapidly [8

8. S. Y. Lu and L. C. Chien, “Carbon nanotube doped liquid crystal OCB cells: physical and electro-optical properties,” Opt. Express 16(17), 12777–12785 (2008). [PubMed]

]. In addition, LCs mixed with NPs showed new properties, such as memory effects [9

9. A. Glushchenko, H. Kresse, G. Puchkovs'ka, V. Reshetnyak, Y. Reznikov, and O. Yaroshchuk, “Memory effect and structure of filled nematic liquid crystals,” Mol. Cryst. Liq. Cryst. (Phila. Pa.) 321(1), 15–30 (1998). [CrossRef]

], frequency modulation [10

10. Y. Shiraishi, N. Toshima, K. Maeda, H. Yoshikawa, J. Xu, and S. Kobayashi, “Frequency modulation response of a liquid-crystal electro-optic device doped with nanoparticles,” Appl. Phys. Lett. 81(15), 2845–2847 (2002). [CrossRef]

], fast response [11

11. W. Lee, C. Y. Wang, and Y. C. Shih, “Effects of carbon nanosolids on the electro-optical properties of a twisted nematic liquid-crystal host,” Appl. Phys. Lett. 85(4), 513–515 (2004). [CrossRef]

], and low driving voltage [12

12. W. K. Lee, J. H. Choi, H. J. Na, J. H. Lim, J. M. Han, J. Y. Hwang, and D. S. Seo, “Low-power operation of vertically aligned liquid-crystal system via anatase-TiO(2) nanoparticle dispersion,” Opt. Lett. 34(23), 3653–3655 (2009). [CrossRef] [PubMed]

]. In other studies, another group used ferromagnetic metal, diamagnetic metal, and metals with a functional group to investigate the phenomenon of LCs doped with NPs [13

13. H. Qi, B. Kinkead, and T. Hegmann, “Unprecedented dual alignment mode and Freedericksz transition in planar nematic liquid crystal cells doped with gold nanoclusters,” Adv. Funct. Mater. 18(2), 212–221 (2008). [CrossRef]

, 14

14. H. Qi, B. Kinkead, V. M. Marx, H. R. Zhang, and T. Hegmann, “Miscibility and alignment effects of mixed monolayer cyanobiphenyl liquid-crystal-capped gold nanoparticles in nematic cyanobiphenyl liquid crystal hosts,” ChemPhysChem 10(8), 1211–1218 (2009). [CrossRef] [PubMed]

]. Overall NPs result in minor changes the physical and chemical properties of LCs, and enhance the function of LCDs.

In this report, we experimented with nematic LCs (NLCs) doped with pure metallic titanium (Ti) NPs. Pure metallic Ti NPs without functional groups have not been used for enhancing the properties of NLC cells to date. Metallic Ti is paramagnetic and has a relatively low conductivity. We dispersed Ti NPs of various doping concentrations in NLC cells. We measured EO characteristics to confirm the enhancement of LCDs properties, and then investigated the changes of LCD properties.

2. Experimental

Ti NPs (~100 nm) dispersed in mineral oil were purchased from Sigma Aldrich Korea. Ti NPs are basic to 98.5% trace metal. In order to disperse NPs s in NLCs, Ti NPs were mixed in NLCs and the mixture was ultrasonicated for 10 min, and then was left to sit for 5 min at room temperature. This process was repeated three times to obtain a uniform dispersion. Homogeneous polyimide (PI, SE-150, 50 nm thick) was prepared by coating onto an indium-tin oxide (ITO) deposited glass substrate using a spin coater. Films were prebaked at 80 °C for 15 min and were then imidized at 230 °C for 1 hour. We implemented the unidirectional rubbing method using velvet on the PI layer to obtain homogeneously aligned LCs. The NLC mixtures were prepared at various Ti NP doping concentrations at weight ratios of 0.1 wt. %, 0.5 wt. %, 1.0 wt. %, 1.5 wt. %, and 2.0 wt. % and were injected into each cell via capillary force at room temperature. A pure NLC cell was prepared for comparison. Positive NLCs (MJ001929, Merck), which have a reflective index (Δn) of 0.077, an isotropic transition temperature of 72 °C, and a dielectric anisotropy Δε (ε) of 8.2, were used during cell fabrication. X-ray diffractrometer (XRD) analysis was performed using a DMAX-IIIA (Rigaku) and Cu-Kα radiation to verify the crystallinity of the NPs in NLCs. Anti-parallel and EO cells were fabricated for measuring the pretilt angles and EO characteristics with cell gaps of 60μm and 4.5μm, respectively. The LCs alignment was investigated using a photomicroscope (Olympus BXP 51). Pretilt angles were measured by the crystal rotation method (TBA 107 tilt-bias angle evaluation device: Autronic). EO measurements of the voltage-transmittance (V–T) characteristics and response times in various doping concentrations of NPs were confirmed using an LCD evaluation system (LCMS-200). We simulated the physical phenomena of the electric field in the LC mixed with NPs by using Ansoft Maxwell software.

3. Results and discussion

The average crystalline sizes of Ti NPs can be calculated via full width at half maximum (FWHM) using the Debye-Scherrer equation [15

15. A. Taylor and H. Sinclair, “On the determination of lattice parameters by the Debye-Scherrer method,” Proc. Phys. Soc. 57(2), 126–135 (1945). [CrossRef]

],
τ= Kλβcosθ
where K is the shape factor, λ is the X-ray wavelength, β is the line broadening at half the maximum intensity (FWHM) in radians, and θ is the Bragg angle. According to the equation, the diameter of the Ti NPs was approximately 100nm.

The pretilt angles of the NLC cells doped from 0.0 wt. % to 1.0 wt. % with Ti NPs were analyzed by the crystal rotating method using the transmittance measurement with a latitudinal rotation of ± 70° at room temperature. Calculated pretilt angles of 0.0 wt. %, 0.1 wt. %, 0.5 wt. % and, 1.0 wt.% Ti NP doped samples were 5.3°, 4.6°, 4.4° and, 3.9°, respectively, as shown in Fig. 2(a)
Fig. 2 Pretilt angles of NLCs with different Ti NP doping concentrations. (a) Plots of the pretilt angle value. (b) Schematic diagram to illustrate the operation of the interaction between the NLC molecules and the alignment layers.
. The pretilt angles were affected by the concentration of Ti NPs, resulting in decreased values as the concentration of Ti NPs was increased.

In fact, the mechanism of pretilt angle formation is still not completely understood. Many mechanisms have been studied to explain the pretilt angle [16

16. R. Arafune, K. Sakamoto, D. Yamakawa, and S. Ushioda, “Pretilt angles of liquid crystals in contact with rubbed polyimide films with different chain inclinations,” Surf. Sci. 368(1-3), 208–212 (1996). [CrossRef]

18

18. S. H. Paek, C. J. Durning, K. W. Lee, and A. Lien, “A mechanistic picture of the effects of rubbing on polyimide surfaces and liquid crystal pretilt angles,” J. Appl. Phys. 83(3), 1270–1279 (1998). [CrossRef]

]. In this report, the pretilt angle formation and decrease may be explained via the mechanism mentioned below. Specifically charged ionic impurities intermittently induced electrification of the Ti NPs. The electric charge-induced Ti NPs in NLC molecules may make the charged ionic impurities separate from the alignment layer by gathering the impurities around Ti NPs under no applied voltage. This occurs because of molecular interaction between the electric charge-induced Ti NPs and the ionic impurities, as shown Fig. 2(b). Therefore, the van der Waals dispersion interactions between NLC molecules and the alignment layers become stronger and the pretilt angle decreases [19

19. H. G. Park, H. Y. Jeong, Y. H. Kim, B. Y. Kim, J. H. Kim, H. I. Yoon, and D. S. Seo, “Electrooptical properties of single-walled carbon-nanotube mixed liquid-crystal cells with rubbed and ion-beam-treated alignment layers,” J. Disp. Technol. 7(12), 644–648 (2011). [CrossRef]

].

The characteristics of voltage-transmittance are shown in Fig. 3
Fig. 3 V-T curves of the Ti NPs doped NLC. The weight percent of the Ti varies from 0.0 wt.% to 1.0 wt.%.
under applied voltages of 0V to 4.0V at room temperature. Voltage transmittance curves demonstrated that the threshold voltage values decreased as Ti NP doping ratio increased. The pure NLC cell exhibited the highest threshold voltage of 1.72V. For 0.1 wt. %, 0.5 wt. %, and 1.0 wt. % Ti NP doping, the threshold voltages were 1.65V, 1.42V, and 1.25V, respectively. The threshold voltage of the NLC cell doped at 1.0 wt. % Ti NPs was 1.25V, and this threshold voltage was reduced by 27% as compared with the pure NLC cell.

Figure 4
Fig. 4 RT characteristics of the homogeneously aligned NLCs with different Ti NP doping concentrations. (a) Response time integration spectra of RT. (b) Response time integration spectra of FT. (c) Schematic diagram to illustrate the operation of NLCs in an on-state NLC cell with doping of Ti NPs. (d) Schematic diagram to illustrate the operation of NLCs in off-state NLC cell with doping of Ti NPs.
shows the response times of the mixed and non-mixed NLC cells and NLC operating mechanisms with Ti NPs. The rise time (fall time) is defined as the time taken for transmittance to change from 90% (10%) to 10% (90%) with a supplied voltage. As shown in Fig. 4(a), for 0.1 wt. %, 0.5 wt. %, and 1.0 wt. Ti NP doping, the rise times (RTs) were 3.9ms, 3.7ms, 3.1ms, and 1.9ms, respectively. The fastest RT was observed in 1.0 wt. % doped Ti NPs, 1.9ms, while the lowest RT was observed in the pure NLC, 3.9ms. The fall times (FTs) were 14.5ms, 13.0ms, 12.7ms, and 11.3ms, respectively, as shown in Fig. 4(b). The fastest FT of 10.7ms was observed in 1.0 wt. % doping concentration and the slowest FT of 17.1ms was observed in the pure NLC cell. All response times decreased as Ti NPs doping increased.

Synthetically, at a 1.0 wt. % doping concentration, Ti NPs are well dispersed, and the EO characteristics were enhanced. The response time was 13.2ms (RT 1.9ms / FT 11.3ms), the threshold voltage was 1.25 V, and the pretilt angle was 3.90°.

The EO enhancement may be explained via two mechanisms. Figure 4(c) shows the operation of NLCs under an applied voltage, and Fig. 4(d) shows the operation of NLCs under no applied voltage. For the first mechanism, if there is a metallic conductor in an electric field, the tangential component of the electric field on a conductor is zero, and the normal component of the electric field at the conductor surface is equal to the surface charge density on the conductor divided by the permittivity of space. No electric field exists in the conductor. The equation for this phenomenon is
EN= DNε= ρSε
where EN is the normal component of the electric strength, DN is the normal component of the electric flux density, ε is permittivity of space, and ρS is surface charge density. The surface charge density of Ti NPs thereby changed the electric field strength in the NLCs. As shown in Fig. 4(c), the metallic Ti NPs changed the path of the electric flux, and then they focused the electric flux around the Ti NPs surface between the top substrate and bottom substrate. Due to the focusing of the electric flux around Ti NPs, the electric flux density increased and the electric field strength is increased around Ti NPs. At the same voltage level, the voltages of the substrates increased the electric field strength. The stronger electric field made NLC molecules rise quickly, and then the desired transmittance was obtained. This phenomenon may also lead to a lower threshold voltage and a faster RT.

A second mechanism explaining the enhanced performance is the suppression of the screen effect [20

20. K. Neyts, S. Vermael, C. Desimpel, G. Stojmenovik, A. R. M. Verschueren, D. K. G. de Boer, D. K. G. de Boer, R. Snijkers, P. Machiels, and A. van Brandenburg, “Lateral ion transport in nematic liquid-crystal devices,” J. Appl. Phys. 94(6), 3891–3896 (2003). [CrossRef]

]. Ion impurities adsorbed on the alignment layer until a voltage was applied across the NLC cell. The screen effect induced by the adsorbed ion charges on the alignment layer creates an inner direct current field and decreased the effective voltage of the NLC layers. Ti NPs in NLC molecules may trap the ions, as shown in Fig. 4(c), leading to an effective decrease in impurities on the alignment layers, thereby abating the screen effect.

Under no applied voltages, FT enhancement can be explained by the change of interaction between LC molecules and alignment layer by Ti NPs as shown Fig. 4(d). Under no applied voltage, charged ionic impurities intermittently induced electrification of the Ti NPs. And the electric charge-induced Ti NPs in NLC molecules may make the charged ionic impurities separate from the alignment layer by gathering the impurities around Ti NPs. Therefore, the force of alignment layer, that pulled liquid crystal, increased. In other words, the van der Waals dispersion interactions between NLC molecules and the alignment layers become stronger. Stronger van der Waals dispersion interactions allow rapid responses in the NLC molecules under no applied voltage.

The two mechanisms described that the lower threshold voltage and faster response times can be attributed to the Ti NPs.

To confirm the boundary conditions of the conductor in the electric field, we simulated the Ti NPs and NLC in an electric field using Ansoft Maxwell software. PI, electrode, and Ti NPs were assigned by default material properties. The dielectric anisotropy (MJ001929, ε = 12.3, ε = 4.1) was used as the setting parameter. Applied voltages were 0V and 5V. Figure 5
Fig. 5 Plots of the results of Ansoft Maxwell software simulation. (a) Plots of the electric flux density in NLC cell doped with Ti NPs. (b) Plots of the electric field strength in NLC cell doped with Ti NPs.
shows the change in the electric field under an applied voltage. As shown in Fig. 5(a), the electric flux density was changed and became strong around Ti NPs. However, in the Ti NP free area, the electric flux density was not changed. The orientation of the electric field changed to the same orientation of the electric flux density and became stronger than in the Ti NP free area, as shown in Fig. 5(b). We ensured that our experimental results matched the results of the software simulation based on general physical theory. Thus, NLC molecule operations are enhanced by stronger electric field strength.

4. Conclusion

In conclusion, we investigated the alignment properties and EO characteristics of NLC cells doped with Ti NPs. Homogeneous alignment of Ti NP doped NLCs at various concentrations were prepared by the rubbing method. We verified high-quality LCDs as control of the doping concentrations of Ti NPs in NLCs at specific conditions. As the Ti NP concentration increased, lower threshold voltages, faster response times, and a lower pretilt angle were obtained. Therefore, we verified that LCDs performance can be controlled by changing the NP concentration in Ti NPs doped with NLCs to improve EO characteristics. The results of Ti NPs doping in NLCs show high performance optical properties necessary for LCD devices, and are suitable for LCD applications by simple, physical mixing of Ti NPs with NLC.

References and links

1.

H. G. Park, J. J. Lee, K. Y. Dong, B. Y. Oh, Y. H. Kim, H. Y. Jeong, B. K. Ju, and D. S. Seo, “Homeotropic alignment of liquid crystals on a nano-patterned polyimide surface using nanoimprint lithography,” Soft Matter 7(12), 5610–5614 (2011). [CrossRef]

2.

A. Glushchenko, C. I. Cheon, J. West, F. Li, E. Büyüktanir, Y. Reznikov, and A. Buchnev, “Ferroelectric particles in liquid crystals: recent frontiers,” Mol. Cryst. Liq. Cryst. (Phila. Pa.) 453(1), 227–237 (2006). [CrossRef]

3.

O. Kurochkin, O. Buchnev, A. Iljin, S. K. Park, S. B. Kwon, O. Grabar, and Y. Reznikov, “A colloid of ferroelectric nanoparticles in a cholesteric liquid crystal,” J. Opt. A, Pure Appl. Opt. 11(2), 024003 (2009). [CrossRef]

4.

K. K. Vardanyan, R. D. Walton, and D. M. Bubb, “Liquid crystal composites with a high percentage of gold nanoparticles,” Liq. Cryst. 38(10), 1279–1287 (2011). [CrossRef]

5.

G. Zhang, X. Chen, J. Zhao, Y. Chai, W. Zhuang, and L. Wang, “Electrophoretic deposition of silver nanoparticles in lamellar lyotropic liquid crystal,” Mater. Lett. 60(23), 2889–2892 (2006). [CrossRef]

6.

H. J. Kim, Y. G. Kang, H. G. Park, K. M. Lee, S. Yang, H. Y. Jung, and D. S. Seo, “Effects of the dispersion of zirconium dioxide nanoparticles on high performance electro-optic properties in liquid crystal devices,” Liq. Cryst. 38(7), 871–875 (2011). [CrossRef]

7.

W. K. Lee, Y. S. Choi, Y. G. Kang, J. W. Sung, D. S. Seo, and C. M. Park, “Super-fast switching of twisted nematic liquid crystals on 2D single wall carbon nanotube networks,” Adv. Funct. Mater. 21(20), 3843–3850 (2011). [CrossRef]

8.

S. Y. Lu and L. C. Chien, “Carbon nanotube doped liquid crystal OCB cells: physical and electro-optical properties,” Opt. Express 16(17), 12777–12785 (2008). [PubMed]

9.

A. Glushchenko, H. Kresse, G. Puchkovs'ka, V. Reshetnyak, Y. Reznikov, and O. Yaroshchuk, “Memory effect and structure of filled nematic liquid crystals,” Mol. Cryst. Liq. Cryst. (Phila. Pa.) 321(1), 15–30 (1998). [CrossRef]

10.

Y. Shiraishi, N. Toshima, K. Maeda, H. Yoshikawa, J. Xu, and S. Kobayashi, “Frequency modulation response of a liquid-crystal electro-optic device doped with nanoparticles,” Appl. Phys. Lett. 81(15), 2845–2847 (2002). [CrossRef]

11.

W. Lee, C. Y. Wang, and Y. C. Shih, “Effects of carbon nanosolids on the electro-optical properties of a twisted nematic liquid-crystal host,” Appl. Phys. Lett. 85(4), 513–515 (2004). [CrossRef]

12.

W. K. Lee, J. H. Choi, H. J. Na, J. H. Lim, J. M. Han, J. Y. Hwang, and D. S. Seo, “Low-power operation of vertically aligned liquid-crystal system via anatase-TiO(2) nanoparticle dispersion,” Opt. Lett. 34(23), 3653–3655 (2009). [CrossRef] [PubMed]

13.

H. Qi, B. Kinkead, and T. Hegmann, “Unprecedented dual alignment mode and Freedericksz transition in planar nematic liquid crystal cells doped with gold nanoclusters,” Adv. Funct. Mater. 18(2), 212–221 (2008). [CrossRef]

14.

H. Qi, B. Kinkead, V. M. Marx, H. R. Zhang, and T. Hegmann, “Miscibility and alignment effects of mixed monolayer cyanobiphenyl liquid-crystal-capped gold nanoparticles in nematic cyanobiphenyl liquid crystal hosts,” ChemPhysChem 10(8), 1211–1218 (2009). [CrossRef] [PubMed]

15.

A. Taylor and H. Sinclair, “On the determination of lattice parameters by the Debye-Scherrer method,” Proc. Phys. Soc. 57(2), 126–135 (1945). [CrossRef]

16.

R. Arafune, K. Sakamoto, D. Yamakawa, and S. Ushioda, “Pretilt angles of liquid crystals in contact with rubbed polyimide films with different chain inclinations,” Surf. Sci. 368(1-3), 208–212 (1996). [CrossRef]

17.

R. Arafune, K. Sakamoto, S. Ushioda, S. Tanioka, and S. Murata, “Importance of rubbing-induced inclination of polyimide backbone structures for determination of the pretilt angle of liquid crystals,” Phys. Rev. E Stat. Phys. Plasmas Fluids Relat. Interdiscip. Topics 58(5), 5914–5918 (1998). [CrossRef]

18.

S. H. Paek, C. J. Durning, K. W. Lee, and A. Lien, “A mechanistic picture of the effects of rubbing on polyimide surfaces and liquid crystal pretilt angles,” J. Appl. Phys. 83(3), 1270–1279 (1998). [CrossRef]

19.

H. G. Park, H. Y. Jeong, Y. H. Kim, B. Y. Kim, J. H. Kim, H. I. Yoon, and D. S. Seo, “Electrooptical properties of single-walled carbon-nanotube mixed liquid-crystal cells with rubbed and ion-beam-treated alignment layers,” J. Disp. Technol. 7(12), 644–648 (2011). [CrossRef]

20.

K. Neyts, S. Vermael, C. Desimpel, G. Stojmenovik, A. R. M. Verschueren, D. K. G. de Boer, D. K. G. de Boer, R. Snijkers, P. Machiels, and A. van Brandenburg, “Lateral ion transport in nematic liquid-crystal devices,” J. Appl. Phys. 94(6), 3891–3896 (2003). [CrossRef]

OCIS Codes
(000.2690) General : General physics
(160.3710) Materials : Liquid crystals
(230.3720) Optical devices : Liquid-crystal devices
(160.4236) Materials : Nanomaterials

ToC Category:
Optical Devices

History
Original Manuscript: January 18, 2012
Revised Manuscript: February 22, 2012
Manuscript Accepted: March 1, 2012
Published: March 5, 2012

Citation
Yong-Seok Ha, Hyung-Jun Kim, Hong-Gyu Park, and Dae-Shik Seo, "Enhancement of electro-optic properties in liquid crystal devices via titanium nanoparticle doping," Opt. Express 20, 6448-6455 (2012)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-20-6-6448


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. H. G. Park, J. J. Lee, K. Y. Dong, B. Y. Oh, Y. H. Kim, H. Y. Jeong, B. K. Ju, and D. S. Seo, “Homeotropic alignment of liquid crystals on a nano-patterned polyimide surface using nanoimprint lithography,” Soft Matter7(12), 5610–5614 (2011). [CrossRef]
  2. A. Glushchenko, C. I. Cheon, J. West, F. Li, E. Büyüktanir, Y. Reznikov, and A. Buchnev, “Ferroelectric particles in liquid crystals: recent frontiers,” Mol. Cryst. Liq. Cryst. (Phila. Pa.)453(1), 227–237 (2006). [CrossRef]
  3. O. Kurochkin, O. Buchnev, A. Iljin, S. K. Park, S. B. Kwon, O. Grabar, and Y. Reznikov, “A colloid of ferroelectric nanoparticles in a cholesteric liquid crystal,” J. Opt. A, Pure Appl. Opt.11(2), 024003 (2009). [CrossRef]
  4. K. K. Vardanyan, R. D. Walton, and D. M. Bubb, “Liquid crystal composites with a high percentage of gold nanoparticles,” Liq. Cryst.38(10), 1279–1287 (2011). [CrossRef]
  5. G. Zhang, X. Chen, J. Zhao, Y. Chai, W. Zhuang, and L. Wang, “Electrophoretic deposition of silver nanoparticles in lamellar lyotropic liquid crystal,” Mater. Lett.60(23), 2889–2892 (2006). [CrossRef]
  6. H. J. Kim, Y. G. Kang, H. G. Park, K. M. Lee, S. Yang, H. Y. Jung, and D. S. Seo, “Effects of the dispersion of zirconium dioxide nanoparticles on high performance electro-optic properties in liquid crystal devices,” Liq. Cryst.38(7), 871–875 (2011). [CrossRef]
  7. W. K. Lee, Y. S. Choi, Y. G. Kang, J. W. Sung, D. S. Seo, and C. M. Park, “Super-fast switching of twisted nematic liquid crystals on 2D single wall carbon nanotube networks,” Adv. Funct. Mater.21(20), 3843–3850 (2011). [CrossRef]
  8. S. Y. Lu and L. C. Chien, “Carbon nanotube doped liquid crystal OCB cells: physical and electro-optical properties,” Opt. Express16(17), 12777–12785 (2008). [PubMed]
  9. A. Glushchenko, H. Kresse, G. Puchkovs'ka, V. Reshetnyak, Y. Reznikov, and O. Yaroshchuk, “Memory effect and structure of filled nematic liquid crystals,” Mol. Cryst. Liq. Cryst. (Phila. Pa.)321(1), 15–30 (1998). [CrossRef]
  10. Y. Shiraishi, N. Toshima, K. Maeda, H. Yoshikawa, J. Xu, and S. Kobayashi, “Frequency modulation response of a liquid-crystal electro-optic device doped with nanoparticles,” Appl. Phys. Lett.81(15), 2845–2847 (2002). [CrossRef]
  11. W. Lee, C. Y. Wang, and Y. C. Shih, “Effects of carbon nanosolids on the electro-optical properties of a twisted nematic liquid-crystal host,” Appl. Phys. Lett.85(4), 513–515 (2004). [CrossRef]
  12. W. K. Lee, J. H. Choi, H. J. Na, J. H. Lim, J. M. Han, J. Y. Hwang, and D. S. Seo, “Low-power operation of vertically aligned liquid-crystal system via anatase-TiO(2) nanoparticle dispersion,” Opt. Lett.34(23), 3653–3655 (2009). [CrossRef] [PubMed]
  13. H. Qi, B. Kinkead, and T. Hegmann, “Unprecedented dual alignment mode and Freedericksz transition in planar nematic liquid crystal cells doped with gold nanoclusters,” Adv. Funct. Mater.18(2), 212–221 (2008). [CrossRef]
  14. H. Qi, B. Kinkead, V. M. Marx, H. R. Zhang, and T. Hegmann, “Miscibility and alignment effects of mixed monolayer cyanobiphenyl liquid-crystal-capped gold nanoparticles in nematic cyanobiphenyl liquid crystal hosts,” ChemPhysChem10(8), 1211–1218 (2009). [CrossRef] [PubMed]
  15. A. Taylor and H. Sinclair, “On the determination of lattice parameters by the Debye-Scherrer method,” Proc. Phys. Soc.57(2), 126–135 (1945). [CrossRef]
  16. R. Arafune, K. Sakamoto, D. Yamakawa, and S. Ushioda, “Pretilt angles of liquid crystals in contact with rubbed polyimide films with different chain inclinations,” Surf. Sci.368(1-3), 208–212 (1996). [CrossRef]
  17. R. Arafune, K. Sakamoto, S. Ushioda, S. Tanioka, and S. Murata, “Importance of rubbing-induced inclination of polyimide backbone structures for determination of the pretilt angle of liquid crystals,” Phys. Rev. E Stat. Phys. Plasmas Fluids Relat. Interdiscip. Topics58(5), 5914–5918 (1998). [CrossRef]
  18. S. H. Paek, C. J. Durning, K. W. Lee, and A. Lien, “A mechanistic picture of the effects of rubbing on polyimide surfaces and liquid crystal pretilt angles,” J. Appl. Phys.83(3), 1270–1279 (1998). [CrossRef]
  19. H. G. Park, H. Y. Jeong, Y. H. Kim, B. Y. Kim, J. H. Kim, H. I. Yoon, and D. S. Seo, “Electrooptical properties of single-walled carbon-nanotube mixed liquid-crystal cells with rubbed and ion-beam-treated alignment layers,” J. Disp. Technol.7(12), 644–648 (2011). [CrossRef]
  20. K. Neyts, S. Vermael, C. Desimpel, G. Stojmenovik, A. R. M. Verschueren, D. K. G. de Boer, D. K. G. de Boer, R. Snijkers, P. Machiels, and A. van Brandenburg, “Lateral ion transport in nematic liquid-crystal devices,” J. Appl. Phys.94(6), 3891–3896 (2003). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1 Fig. 2 Fig. 3
 
Fig. 4 Fig. 5
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited