OSA's Digital Library

Optics Express

Optics Express

  • Editor: C. Martijn de Sterke
  • Vol. 20, Iss. 7 — Mar. 26, 2012
  • pp: 7066–7070
« Show journal navigation

Optical trapping with “on-demand” two-photon luminescence using Cr:LiSAF laser with optically addressed saturable Bragg reflector

Vasili G. Savitski, Nikolaus K. Metzger, Stephane Calvez, David Burns, W. Sibbett, and C. T. A. Brown  »View Author Affiliations


Optics Express, Vol. 20, Issue 7, pp. 7066-7070 (2012)
http://dx.doi.org/10.1364/OE.20.007066


View Full Text Article

Acrobat PDF (1060 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We demonstrate a diode-pumped Cr:LiSAF laser with controllable and reliable fast switching between its continuous-wave and mode-locked states of operation using an optically-addressed semiconductor Bragg reflector, permitting dyed microspheres to be continuously trapped and monitored using a standard microscope imaging and on-demand two-photon-excited luminescence techniques.

© 2012 OSA

1. Introduction

Ultrafast pulsed solid-state lasers are becoming ubiquitous tools for an ever-increasing range of applications including scientific research, material processing and bio-photonics [1

1. J. M. Hopkins, G. J. Valentine, W. Sibbett, J. A. der Au, F. Morier-Genoud, U. Keller, and A. Valster, “Efficient, low-noise, SESAM-based femtosecond Cr3+: LiSrAlF6 laser,” Opt. Commun. 154(1-3), 54–58 (1998). [CrossRef]

5

5. B. Agate, C. T. A. Brown, W. Sibbett, and K. Dholakia, “Femtosecond optical tweezers for in-situ control of two-photon fluorescence,” Opt. Express 12(13), 3011–3017 (2004). [CrossRef] [PubMed]

]. This use has widespread as they have gained in reliability, ease of operation and reduced maintenance. A key element to this success has been the delivery of robust self-starting pulsed systems which exploit an intra-cavity semiconductor saturable absorber (SA) in the form of a Semiconductor Bragg Reflector (SBR) [2

2. V. G. Savitski, A. J. Kemp, S. Calvez, and D. Burns, “Optically Pumped Saturable Bragg Reflectors: Nonlinear Spectroscopy and Application in Ultrafast Lasers,” IEEE J. Quantum Electron. 46(11), 1650–1655 (2010). [CrossRef]

,4

4. S. Tsuda, W. H. Knox, E. A. de Souza, W. Y. Jan, and J. E. Cunningham, “Low-loss intracavity AlAs/AlGaAs saturable Bragg reflector for femtosecond mode locking in solid-state lasers,” Opt. Lett. 20(12), 1406–1408 (1995). [CrossRef] [PubMed]

] as the element to initiate and maintain the ultrashort pulse generation. More recently, the emphasis has turned to the development of lasers with higher performance and/or which present more advanced functionalities. Among the identified functionalities is the ability to simply switch the laser between continuous-wave (CW) mode-locked (ML) and CW regimes of operation - this state-switching has been shown to offer novel opportunities and benefits to the bio-photonics application sector [5

5. B. Agate, C. T. A. Brown, W. Sibbett, and K. Dholakia, “Femtosecond optical tweezers for in-situ control of two-photon fluorescence,” Opt. Express 12(13), 3011–3017 (2004). [CrossRef] [PubMed]

7

7. J. Ando, G. Bautista, N. Smith, K. Fujita, and V. R. Daria, “Optical trapping and surgery of living yeast cells using a single laser,” Rev. Sci. Instrum. 79(10), 103705 (2008). [CrossRef] [PubMed]

].

Here, we demonstrate that a diode-pumped Cr:LiSAF laser can controllably and reliably be switched between its CW and ML states of operation using an optically-addressed SBR, permitting dyed microspheres to be continuously trapped and monitored using standard microscope imaging and on-demand two-photon-excited luminescence techniques.

2. Experimental set-up

The demonstrator platform for on-demand two-photon luminescence and/or optical tweezing of polymer microspheres consists of a diode-pumped Cr:LiSAF laser with optically addressed SBR for a fast switching between CW and ML modes of operation and a homemade optical microscope.

The Cr:LiSAF laser used in the system is schematically represented in Fig. 1
Fig. 1 Schematic of the diode-pumped Cr:LiSAF laser arrangement. OC – 1% output coupler. All curved mirrors are highly reflective (HR) within 800-900 nm spectral range. EDL – External Diode Laser.
and was pumped on either side by two polarisation-coupled laser diodes emitting up to 130mW at 660nm [1

1. J. M. Hopkins, G. J. Valentine, W. Sibbett, J. A. der Au, F. Morier-Genoud, U. Keller, and A. Valster, “Efficient, low-noise, SESAM-based femtosecond Cr3+: LiSrAlF6 laser,” Opt. Commun. 154(1-3), 54–58 (1998). [CrossRef]

]. A Z-shape cavity was established using two folding mirrors with radii of curvature of 100 mm separated by 146mm. The SBR was positioned at the end of the short (100mm-long) arm of the cavity whist its long arm (which is 508mm long) included two FS10 prisms setup to promote positive intra-cavity group dispersion. This arrangement provided TEM00 mode radii within the Cr:LiSAF crystal and on the SBR of 36μm and 30μm respectively. The output coupler at the end of the longest cavity arm had a reflectivity of 99%, and the oscillation wavelength was tuned by a slit positioned between the output coupler and the FS10 prism. The SBR employed in the laser included a single GaAs/AlGaAs quantum well positioned in the last high index layer of a 30-pair AlGaAs/AlAs distributed Bragg Reflector. Its saturation characteristics presented at the peak of the exciton 0.5% modulation depth with a saturation fluence of ~12μJ/cm2 as shown in [2

2. V. G. Savitski, A. J. Kemp, S. Calvez, and D. Burns, “Optically Pumped Saturable Bragg Reflectors: Nonlinear Spectroscopy and Application in Ultrafast Lasers,” IEEE J. Quantum Electron. 46(11), 1650–1655 (2010). [CrossRef]

]. The laser mode of operation (CW or ML) was controlled by optical pumping of the SBR with external diode laser (EDL) emitting at 670nm with pump power of ~1W [2

2. V. G. Savitski, A. J. Kemp, S. Calvez, and D. Burns, “Optically Pumped Saturable Bragg Reflectors: Nonlinear Spectroscopy and Application in Ultrafast Lasers,” IEEE J. Quantum Electron. 46(11), 1650–1655 (2010). [CrossRef]

].

For the remainder of the work, the Cr:LiSAF laser emission wavelength was tuned to 835nm and SBR substrate temperature maintained at room temperature. In this case, when the SBR is unpumped (EDL off) the laser operated in CW mode. When the EDL was turned on with 1W of output power and its ~100μm-radius beam coincided with the Cr:LiSAF laser cavity mode on the SBR, the laser switched to CW ML operation. The physical processes behind this change of mode of operation were discussed in details in [2

2. V. G. Savitski, A. J. Kemp, S. Calvez, and D. Burns, “Optically Pumped Saturable Bragg Reflectors: Nonlinear Spectroscopy and Application in Ultrafast Lasers,” IEEE J. Quantum Electron. 46(11), 1650–1655 (2010). [CrossRef]

,3

3. V. G. Savitski, D. Burns, and S. Calvez, “Optically-pumped saturable absorber for fast switching between continuous-wave and passively mode-locked regimes of a Nd:YVO4 laser,” Opt. Express 17(7), 5373–5378 (2009). [CrossRef] [PubMed]

] where it was shown that the major factor responsible for switching is a fast heat-induced shift of the absorption edge of the SBR towards longer wavelengths resulting from the pumping of the SBR. Indeed, this localized heating induces laser mode switching with transient times orders of magnitude shorter than when the SBR is directly heated by a Peltier element [2

2. V. G. Savitski, A. J. Kemp, S. Calvez, and D. Burns, “Optically Pumped Saturable Bragg Reflectors: Nonlinear Spectroscopy and Application in Ultrafast Lasers,” IEEE J. Quantum Electron. 46(11), 1650–1655 (2010). [CrossRef]

4

4. S. Tsuda, W. H. Knox, E. A. de Souza, W. Y. Jan, and J. E. Cunningham, “Low-loss intracavity AlAs/AlGaAs saturable Bragg reflector for femtosecond mode locking in solid-state lasers,” Opt. Lett. 20(12), 1406–1408 (1995). [CrossRef] [PubMed]

].

Here, the typical switching times from CW into ML mode of operation were measured to be ~1.5ms (Fig. 2
Fig. 2 Output from the Cr:LiSAF laser (blue) with SBR periodically pumped by EDL (red). Inset: Typical response of the Cr:LiSAF laser output on external optical pumping of the SBR.
, inset). As shown in Fig. 2, it was a fully controllable and reproducible process where the EDL was operated in a quasi-CW regime and led to a periodical switching of the Cr:LiSAF laser from CW into ML mode of operation and back. This method of control of the laser mode of operation is advantageous over previously reported alternatives where either a mechanical modification of the laser cavity (as in the case of the Kerr-lens ML Ti:sapphire laser in [5

5. B. Agate, C. T. A. Brown, W. Sibbett, and K. Dholakia, “Femtosecond optical tweezers for in-situ control of two-photon fluorescence,” Opt. Express 12(13), 3011–3017 (2004). [CrossRef] [PubMed]

]) or a change of the pump laser output power [6,7

7. J. Ando, G. Bautista, N. Smith, K. Fujita, and V. R. Daria, “Optical trapping and surgery of living yeast cells using a single laser,” Rev. Sci. Instrum. 79(10), 103705 (2008). [CrossRef] [PubMed]

] were required.

The maximum output power of the Cr:LiSAF laser in CW mode at 430mW of absorbed pump power was measured to be 30mW whilst in ML mode it was slightly lower – 28mW. The produced pulses at maximum output power were measured to be 212fs (Fig. 3
Fig. 3 Intensity autocorrelation trace of the ML pulse from the Cr;LiSAF laser. Inset, corresponding optical spectrum (duration– bandwidth product = 0.33).
) with a corresponding spectral width of 3.9nm (Fig. 3, inset), giving a near-transform-limited time-bandwidth product of 0.33.

Subsequently, a home-made optical microscope for optical tweezing and two-photon luminescence experiments was built. It included a two lens telescope to expand the beam emitted by the Cr:LiSAF laser to fill the back aperture of a 100x objective (Fig. 4
Fig. 4 A schematic set-up for experiments on optical trapping and two-photon luminescence.
). The laser emission after the 100x objective was focused onto a microscope slide on top of which the sample in water solution was introduced and covered with a coverslip. To monitor the sample, white-light illumination was set up on the backside of the microscope slide and images were recorded by a CCD camera using a dichroic-mirror pick-off from the light collected by the 100x objective (see Fig. 4). The average pump power at the sample was measured to be ~10mW and is sufficient to induce two-photon excitation from dyed microspheres as shown hereafter. This power level would also be adequate for optical dissection of biological cells [7

7. J. Ando, G. Bautista, N. Smith, K. Fujita, and V. R. Daria, “Optical trapping and surgery of living yeast cells using a single laser,” Rev. Sci. Instrum. 79(10), 103705 (2008). [CrossRef] [PubMed]

], a topic which will form the basis of further investigations.

3. “On demand” two-photon luminescence of a trapped microsphere

The sample in the experiment was a water solution containing blue-dyed polymer microspheres with a mean diameter of 3μm (Thermo-Scientific). The microspheres being pumped at 412nm exhibit luminescence with peaks at 445 and 473nm. Emission from the Cr:LiSAF laser at the wavelength of 835nm can lead to two-photon absorption in this dye and subsequent luminescence from a microsphere, providing that the pulse peak intensity is high enough [5

5. B. Agate, C. T. A. Brown, W. Sibbett, and K. Dholakia, “Femtosecond optical tweezers for in-situ control of two-photon fluorescence,” Opt. Express 12(13), 3011–3017 (2004). [CrossRef] [PubMed]

], which is the case when the above-described laser operated in ML regime with pulse peak powers of ~670W.

The movie presented in Fig. 5
Fig. 5 Movie of on-demand two-photon luminescence of a trapped microsphere doped with the dye. Two-photon luminescence is excited by emission from the Cr:LiSAF laser operating in ML regime. (Media 1)
demonstrates the control of a trapped microsphere with on-demand two-photon luminescence. At the beginning of the movie, a microsphere is trapped by the ML output of the Cr:LiSAF laser and displays two-photon-induced luminescence. It was shown before that efficiencies (Q-value) of optical trapping using CW and ML mode of operation of the same laser are equal [5

5. B. Agate, C. T. A. Brown, W. Sibbett, and K. Dholakia, “Femtosecond optical tweezers for in-situ control of two-photon fluorescence,” Opt. Express 12(13), 3011–3017 (2004). [CrossRef] [PubMed]

]. Indeed, when the laser is switched into its CW mode of operation (approximately 3 seconds after beginning of the movie) the microsphere remained trapped. In this regime of operation, the CW laser emission is too low to induce any two-photon absorption in the dye; therefore the luminescence from a microsphere disappears.

The subsequent movie sequence demonstrates on-demand two-photon excitation of the constantly trapped microspheres as well as the reliability of the laser operation and switching.

4. Conclusion

We demonstrated that diode-pumped Cr:LiSAF laser which incorporates an optically-addressed SBR is an efficient, compact, simple and reliable tool for biological applications where optical tweezing of the object should be accompanied with two-photon luminescence from a trapped particle. We believe, this method of optically addressing the SBR could be implemented in a Ti:sapphire laser with higher output powers [2

2. V. G. Savitski, A. J. Kemp, S. Calvez, and D. Burns, “Optically Pumped Saturable Bragg Reflectors: Nonlinear Spectroscopy and Application in Ultrafast Lasers,” IEEE J. Quantum Electron. 46(11), 1650–1655 (2010). [CrossRef]

] and pumped with blue laser diodes [8

8. P. W. Roth, A. J. Maclean, D. Burns, and A. J. Kemp, “Direct diode-laser pumping of a mode-locked Ti:sapphire laser,” Opt. Lett. 36(2), 304–306 (2011). [CrossRef] [PubMed]

] to create a compact real-time multitasking platform for bio-photonics applications.

Acknowledgments

The authors would like to acknowledge EPSRC programme “Ultrafast Modular Lasers” for funding.

References and links

1.

J. M. Hopkins, G. J. Valentine, W. Sibbett, J. A. der Au, F. Morier-Genoud, U. Keller, and A. Valster, “Efficient, low-noise, SESAM-based femtosecond Cr3+: LiSrAlF6 laser,” Opt. Commun. 154(1-3), 54–58 (1998). [CrossRef]

2.

V. G. Savitski, A. J. Kemp, S. Calvez, and D. Burns, “Optically Pumped Saturable Bragg Reflectors: Nonlinear Spectroscopy and Application in Ultrafast Lasers,” IEEE J. Quantum Electron. 46(11), 1650–1655 (2010). [CrossRef]

3.

V. G. Savitski, D. Burns, and S. Calvez, “Optically-pumped saturable absorber for fast switching between continuous-wave and passively mode-locked regimes of a Nd:YVO4 laser,” Opt. Express 17(7), 5373–5378 (2009). [CrossRef] [PubMed]

4.

S. Tsuda, W. H. Knox, E. A. de Souza, W. Y. Jan, and J. E. Cunningham, “Low-loss intracavity AlAs/AlGaAs saturable Bragg reflector for femtosecond mode locking in solid-state lasers,” Opt. Lett. 20(12), 1406–1408 (1995). [CrossRef] [PubMed]

5.

B. Agate, C. T. A. Brown, W. Sibbett, and K. Dholakia, “Femtosecond optical tweezers for in-situ control of two-photon fluorescence,” Opt. Express 12(13), 3011–3017 (2004). [CrossRef] [PubMed]

6.

http://optics.org/article/36573.

7.

J. Ando, G. Bautista, N. Smith, K. Fujita, and V. R. Daria, “Optical trapping and surgery of living yeast cells using a single laser,” Rev. Sci. Instrum. 79(10), 103705 (2008). [CrossRef] [PubMed]

8.

P. W. Roth, A. J. Maclean, D. Burns, and A. J. Kemp, “Direct diode-laser pumping of a mode-locked Ti:sapphire laser,” Opt. Lett. 36(2), 304–306 (2011). [CrossRef] [PubMed]

OCIS Codes
(140.3580) Lasers and laser optics : Lasers, solid-state
(140.4050) Lasers and laser optics : Mode-locked lasers
(350.4855) Other areas of optics : Optical tweezers or optical manipulation

ToC Category:
Ultrafast Optics

History
Original Manuscript: December 19, 2011
Manuscript Accepted: January 23, 2012
Published: March 13, 2012

Virtual Issues
Vol. 7, Iss. 5 Virtual Journal for Biomedical Optics
Modular Ultrafast Lasers (Invited Only) (2012) Optics Express

Citation
Vasili G. Savitski, Nikolaus K. Metzger, Stephane Calvez, David Burns, W. Sibbett, and C. T. A. Brown, "Optical trapping with “on-demand” two-photon luminescence using Cr:LiSAF laser with optically addressed saturable Bragg reflector," Opt. Express 20, 7066-7070 (2012)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-20-7-7066


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. J. M. Hopkins, G. J. Valentine, W. Sibbett, J. A. der Au, F. Morier-Genoud, U. Keller, and A. Valster, “Efficient, low-noise, SESAM-based femtosecond Cr3+: LiSrAlF6 laser,” Opt. Commun.154(1-3), 54–58 (1998). [CrossRef]
  2. V. G. Savitski, A. J. Kemp, S. Calvez, and D. Burns, “Optically Pumped Saturable Bragg Reflectors: Nonlinear Spectroscopy and Application in Ultrafast Lasers,” IEEE J. Quantum Electron.46(11), 1650–1655 (2010). [CrossRef]
  3. V. G. Savitski, D. Burns, and S. Calvez, “Optically-pumped saturable absorber for fast switching between continuous-wave and passively mode-locked regimes of a Nd:YVO4 laser,” Opt. Express17(7), 5373–5378 (2009). [CrossRef] [PubMed]
  4. S. Tsuda, W. H. Knox, E. A. de Souza, W. Y. Jan, and J. E. Cunningham, “Low-loss intracavity AlAs/AlGaAs saturable Bragg reflector for femtosecond mode locking in solid-state lasers,” Opt. Lett.20(12), 1406–1408 (1995). [CrossRef] [PubMed]
  5. B. Agate, C. T. A. Brown, W. Sibbett, and K. Dholakia, “Femtosecond optical tweezers for in-situ control of two-photon fluorescence,” Opt. Express12(13), 3011–3017 (2004). [CrossRef] [PubMed]
  6. http://optics.org/article/36573 .
  7. J. Ando, G. Bautista, N. Smith, K. Fujita, and V. R. Daria, “Optical trapping and surgery of living yeast cells using a single laser,” Rev. Sci. Instrum.79(10), 103705 (2008). [CrossRef] [PubMed]
  8. P. W. Roth, A. J. Maclean, D. Burns, and A. J. Kemp, “Direct diode-laser pumping of a mode-locked Ti:sapphire laser,” Opt. Lett.36(2), 304–306 (2011). [CrossRef] [PubMed]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1 Fig. 2 Fig. 3
 
Fig. 4 Fig. 5
 

Multimedia

Multimedia FilesRecommended Software
» Media 1: MOV (2585 KB)      QuickTime

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited