OSA's Digital Library

Optics Express

Optics Express

  • Editor: Andrew M. Weiner
  • Vol. 21, Iss. 16 — Aug. 12, 2013
  • pp: 18963–18968
« Show journal navigation

Q-switched pulse laser generation from double-cladding Nd:YAG ceramics waveguides

Yang Tan, Qingfang Luan, Fengqin Liu, Feng Chen, and Javier Rodríguez Vázquez de Aldana  »View Author Affiliations


Optics Express, Vol. 21, Issue 16, pp. 18963-18968 (2013)
http://dx.doi.org/10.1364/OE.21.018963


View Full Text Article

Acrobat PDF (2005 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

This work reports on the Q-switched pulsed laser generation from double-cladding Nd:YAG ceramic waveguides. Double-cladding waveguides with different combination of diameters were inscribed into a sample of Nd:YAG ceramic. With an additional semiconductor saturable absorber, stable pulsed laser emission at the wavelength of 1064 nm was achieved with pulses of 21 ns temporal duration and ~14 μJ pulse energy at a repetition rate of 3.65 MHz.

© 2013 OSA

1. Introduction

Rare earth doped yttrium aluminum garnet (RE:YAG) ceramics is a latest developed gain media for high power solid state lasers, owing to its excellent lasing properties [1

1. A. Ikesue and Y. L. Aung, “Ceramic laser materials,” Nat. Photonics 2(12), 721–727 (2008). [CrossRef]

]. Compared with its single-crystalline partners, RE:YAG ceramics possess similar fluorescence ability and can be produced in larger homogenous volumes. Efficient high power operation of the neodymium doped YAG (Nd:YAG) ceramic lasers have been realized under configuration of continuous wave [2

2. Y. Chen, W. Liu, Y. Bo, B. Jiang, J. Xu, J. Li, Y. Xu, Y. Pan, J. L. Xu, X. Feng, Y. Guo, Y. Shen, F. Yang, L. Yuan, H. Yuan, Q. Peng, D. Cui, and Z. Xu, “High-efficiency high-power QCW diode-side-pumped zigzag Nd:YAG ceramic slab laser,” Appl. Phys. B 111(1), 111–116 (2013). [CrossRef]

], Q switching [3

3. S. Men, Z. Liu, X. Zhang, Q. Wang, H. Shen, F. Bai, L. Gao, X. Xu, R. Wei, and X. Chen, “A graphene passively Q-switched Nd:YAG ceramic laser at 1123 nm,” Laser Phys. Lett. 10(3), 035803 (2013). [CrossRef]

] and mode locking [4

4. G. Xie, D. Tang, J. Kong, and L. Qian, “Passive mode-locking of a Nd:YAG ceramic laser by optical interference modulation in a GaAs wafer,” Opt. Express 15(9), 5360–5365 (2007). [CrossRef] [PubMed]

]. Except for these bulk laser systems, Nd:YAG ceramics are also used as the gain media for the active devices in integrated photonics [5

5. G. A. Torchia, P. F. Meilán, A. Rodenas, D. Jaque, C. Mendez, and L. Roso, “Femtosecond laser written surface waveguides fabricated in Nd:YAG ceramics,” Opt. Express 15(20), 13266–13271 (2007). [CrossRef] [PubMed]

, 6

6. Y. Tan and F. Chen, “Proton-implanted optical channel waveguides in Nd:YAG laser ceramics,” J. Phys. D Appl. Phys. 43(7), 075105 (2010). [CrossRef]

].

Waveguide lasers and amplifiers are the basic active devices, for integrated optics. As a basic component of these active devices, waveguide structures confine light within micrometric or sub-micrometric scales and can obtain higher optical intra-cavity intensities compared with bulk [7

7. F. Chen and J. R. Vázquez de Aldana, “Optical waveguides in crystalline dielectric materials produced by femtosecond-laser micromachining,” Laser Photonics Rev. (Wiley online early view) DOI: [CrossRef]

9

9. C. Grivas, “Optically pumped planar waveguide lasers, Part I: Fundamentals and fabrication techniques,” Prog. Quantum Electron. 35(6), 159–239 (2011). [CrossRef]

]. Until now, few fabrication techniques have been used for waveguide fabrication in YAG ceramics, such as ultrafast laser writing or ion implantation/irradiation [5

5. G. A. Torchia, P. F. Meilán, A. Rodenas, D. Jaque, C. Mendez, and L. Roso, “Femtosecond laser written surface waveguides fabricated in Nd:YAG ceramics,” Opt. Express 15(20), 13266–13271 (2007). [CrossRef] [PubMed]

, 10

10. Y. Tan, Q. Luan, F. Liu, S. Akhmadaliev, S. Zhou, and F. Chen, “Swift carbon ion irradiated Nd:YAG ceramic optical waveguide amplifier,” Opt. Express 21(12), 13992–13997 (2013). [CrossRef] [PubMed]

]. The ultrafast laser writing technique is a well known waveguide fabrication method [11

11. F. M. Bain, W. F. Silva, A. A. Lagatsky, R. R. Thomson, N. D. Psaila, A. K. Kar, W. Sibbett, D. Jaque, and C. T. A. Brown, “Microspectroscopy of ultrafast laser inscribed channel waveguides in Yb:tungstate crystals,” Appl. Phys. Lett. 98(14), 141108 (2011). [CrossRef] [PubMed]

]. Ultrafast laser written waveguides, depending on the relative location of the waveguide and writing tracks, could be classified into Type I waveguides (in the positive refractive index changed track) [12

12. Y. L. Lee, N. E. Yu, C. Jung, B.-A. Yu, I.-B. Sohn, S.-C. Choi, Y.-C. Noh, D.-K. Ko, W.-S. Yang, H.-M. Lee, W.-K. Kim, and H.-Y. Lee, “Second-harmonic generation in periodically poled lithium niobate waveguides fabricated by femtosecond laser pulses,” Appl. Phys. Lett. 89(17), 171103 (2006). [CrossRef]

], Type II stress-induced waveguides (typically between two written tracks with negative index change) [13

13. T. Calmano, A.-G. Paschke, J. Siebenmorgen, S. T. Fredrich-Thornton, H. Yagi, K. Petermann, and G. Huber, “Characterization of an Yb:YAG ceramic waveguide laser, fabricated by the direct femtosecond-laser writing technique,” Appl. Phys. B 103(1), 1–4 (2011). [CrossRef]

] and Type III waveguides (in the core surrounded by tracks) [14

14. H. Liu, Y. Jia, J. R. Vázquez de Aldana, D. Jaque, and F. Chen, “Femtosecond laser inscribed cladding waveguides in Nd:YAG ceramics: Fabrication, fluorescence imaging and laser performance,” Opt. Express 20(17), 18620–18629 (2012). [CrossRef] [PubMed]

]. More recently, a new structure, so called double-cladding waveguides, has been reported, which is a tubular cladding surrounded by another concentric cladding with larger size [15

15. Y. Jia, J. R. Vázquez de Aldana, and F. Chen, “Efficient waveguide lasers in femtosecond laser inscribed double-cladding waveguides of Yb:YAG ceramics,” Opt. Mater. Express 3(5), 645–650 (2013). [CrossRef]

]. With this structure, the performance of the laser oscillation was modified by the diameter of the outside tubular cladding. For example, the slope efficiency of the 1030 nm laser emission was increased from 38% to 63% as diameters of outer claddings varied from 100 μm to 200 μm.

The pulse laser with high peak power density and good flexibility is significant for applications of medicine and nonlinear optics. Pulse fiber lasers could be achieved by the conventional Q-switches, such as acousto-optic modulators (AOM) and solid-state saturable absorbers, which simply replaces one end mirror of the fiber laser [16

16. D. J. Richardson, J. Nilsson, and W. A. Clarkson, “High power fiber lasers: current status and future perspectives,” J. Opt. Soc. Am. B 27(11), B63–B92 (2010). [CrossRef]

]. And compact fiber pulse laser could be easily incorporated into a variety of material processing applications. Compared with fiber laser, the waveguide laser has much smaller size and higher integration level. With the extremely short cavity length of waveguide laser, it enables pulse widths well below 1 ns under Q-switched operation. Hence, it is attracting to analyze the Q-switching performance in the waveguide laser devices. So far, Q-switching has been demonstrated in the ion-doped laser crystal waveguide [17

17. A. Okhrimchuk, “Femtosecond fabrication of waveguides in ion-doped laser crystal,” in Coherence and Ultrashort Pulse Laser Emission, F. J. Duarte, ed., (InTech, 2010).

19

19. A. G. Okhrimchuk, V. K. Mezentsev, V. V. Dvoyrin, A. S. Kurkov, E. M. Sholokhov, S. K. Turitsyn, A. V. Shestakov, and I. Bennion, “Waveguide-saturable absorber fabricated by femtosecond pulses in YAG:Cr4+ crystal for Q-switched operation of Yb-fiber laser,” Opt. Lett. 34(24), 3881–3883 (2009). [CrossRef] [PubMed]

].

In this paper, we report on the Q-switched pulsed laser generation based on double-cladding Nd:YAG ceramic waveguides fabricated with a femtosecond laser beam. This kind of waveguide has the ability to enhance the laser performance of single cladding waveguides. Different inner and outer diameter of the claddings were used inscribed into the Nd:YAG ceramics by the femtosecond laser. Adhering a semiconductor saturable absorber to one end facet of waveguides, Q-switched operation with stable pulse duration and pulse power was demonstrated.

2. Experiments

The Nd:YAG ceramic used in this work is doped by 2 at.% Nd3+ ions (obtained from Baikowski Ltd., Japan) and was cut into dimensions of 10 × 7 × 2 (x × y × z) mm3 with the biggest facets optically polished. Waveguide structures in Nd:YAG ceramic were fabricated by the ultrafast laser writing method. In the process of the experiment, a linearly polarized femtosecond laser (120 fs pulse duration) from an amplified Ti:Sapphire laser system (Spitfire, Spectra Physics, USA) was applied for the inscription. And the pulses have a central wavelength of 800 nm at 1 kHz repetition rate and 1 mJ maximum pulse energy. The detailed experimental process is the same as that reported in [15

15. Y. Jia, J. R. Vázquez de Aldana, and F. Chen, “Efficient waveguide lasers in femtosecond laser inscribed double-cladding waveguides of Yb:YAG ceramics,” Opt. Mater. Express 3(5), 645–650 (2013). [CrossRef]

]. According to the diameter of the inner and outer cladding, waveguides are numbered as shown in Fig. 1
Fig. 1 Cross-section microscope image of the femtosecond laser inscribed double cladding Nd:YAG ceramics waveguides Nos. 1-6, which are composed of inner and outer concentric tubular claddings. The diameters of the double cladding waveguides are No. 1 30μm/100μm, No. 2 30μm/150μm, No. 3 30μm/200μm, No. 4 40μm/100μm, No. 5 40μm/150μm and No. 6 40μm/200μm, respectively.
: the combination of the diameter of the inner and outer tubular cladding are No. 1 30μm/100μm, No. 2 30μm/150μm, No. 3 30μm/200μm, No. 4 40μm/100μm, No. 5 40μm/150μm and No. 6 40μm/200μm, respectively. To estimate the refractive index change (Δn) of the waveguide, we measured the angle of aperture of the guided mode in the far-field at wavelength of 1064 nm, which have a maximum far-field angular aperture of ~8°. Based on the method described in [20

20. J. Siebenmorgen, T. Calmano, K. Petermann, and G. Huber, “Highly efficient Yb:YAG channel waveguide laser written with a femtosecond-laser,” Opt. Express 18(15), 16035–16041 (2010). [CrossRef] [PubMed]

], the refractive index change in the tubular central waveguide is estimated to be ~0.008. The scattering loss of the waveguides, which is induced by the surface roughness of the waveguide walls, was measured by the Fabry-Perot method. A red laser (632.8 nm) was used as the detecting light, provided that the absorption of Nd:YAG ceramics at this wavelength can be neglected. According to the measurements, the loss was 1 ± 0.2 dB/cm in waveguides No. 1, 2, 3, and 1.5 ± 0.2 dB/cm in waveguides No. 4, 5, 6.

After inscription, end facets of the sample perpendicular to waveguides were optically polished. For the purpose of pulsed laser generation, both facets were particularly designed. As shown in Fig. 2
Fig. 2 Schematic plot of the experimental setup for the pulsed laser generation in the double-cladding Nd:YAG ceramic waveguides.
, facet 1 was adhesion to a semiconductor saturable mirror (SESAM) with ~95% reflectance for the laser Q-switching. Facet 2 was coated by an optical film with a reflectivity of >99% at 1064 nm and a transmission of >98% at 810 nm. A continuous laser at the wavelength of 810 nm was chosen as the pump source, which comes from a tunable Ti:Sapphire laser (Coherent MBR 110). With a convex lens (focal length is 25 mm), the pumping laser was coupled into the inner-cladding waveguide through facet 2. The diameter of the focused light was around 20 μm, which insure that the pumping light will not be coupled into the outside cladding waveguide. The generated laser light passed through the SESAM and was collected by a 20 × microscope objective lens (N.A. = 0.4).

3. Results and discussion

Laser emission was obtained from the six waveguides. As depicted in the insets of Fig. 3
Fig. 3 Slope efficiency (a) and threshold (b) of the output pulsed laser as a function of the waveguide Nos. The pulse train and the laser oscillation spectra of the pulsed laser are shown in the inset of (a) and (b) in the waveguide No.3.
, the output laser of waveguides was the pulse laser at the wavelength of 1064 nm with the pumping power above the laser threshold. And the timing jitter is hardly observed with the maximum power of pumping laser. Figure 3 shows the slope efficiency, the lasing threshold and the spectra of the generated pulsed lasers of the double-cladding waveguides. The slope efficiency was measured to be Φ30/200≈7.8%, Φ30/150≈6.5%, and Φ30/100≈5.2% for the 30 μm inner core waveguides in comparison with Φ40/200≈6.3%, Φ40/150≈5.7%, and Φ40/100≈4.2% for the 40 μm inner core ones. The average threshold (launched power) is ~47 mW and ~66 mW for the 30 μm and 40 μm inner core cladding waveguides, respectively. It seems that the slope efficiency increases in waveguides with the same inner core, as the diameters of outer claddings increase from 100 μm to 200 μm. In turn, the threshold is determined by the size of inner core and it is independent on the outer cladding size. Compared with waveguides with the same diameter of outer cladding, the generated laser has lower threshold and higher slope efficiency in cladding waveguides with smaller inner core. In our opinion, the inner and outer cladding of double-cladding waveguides play different roles in the laser generation. The inner cladding is the laser output volume, whose cross section determines the intensity in the Fabry-Perot laser resonator. Hence the laser threshold is determined by the inner cladding. Meanwhile the outer cladding confines more pumping light into the whole structure inducing higher laser output power. So, simultaneous smaller inner and larger outer cladding will lead to better laser performance (lower threshold and higher slope efficiency).

To simplify the discussion, we take the waveguide No. 3 as an example to describe the pulse laser performance in double-cladding waveguides, which has the highest slope efficiency and the smallest threshold. Figure 5
Fig. 5 Results for the generated pulsed laser from No. 1 waveguide by the Q-switching method using a SESAM as the out-coupling mirror. Repetition rate, average output power (a), pulse duration and pulse energy (b) as a function of launched pump power.
demonstrated the output characteristics of the Q-switched pulsed laser. With the maximum launched power, the total average output power and repetition rate reached 48 mW and 3.65 MHz respectively (Fig. 5 (a)). Depending on the increasing of pump power, there is a nearly linear dependence of average output power corresponding to the slope efficiency of 7.8%. It should be noted that the value of the slope efficiency is reduced when operating in Q-switching mode. Without adhering the SESAM at the end facet of the waveguides, the slope efficiency of the output continuous wave laser from waveguide No. 3 is ~60%. The significant reduction results from the high reflection of the saturable absorber, which was used as the output mirror.

Figure 5 (b) shows the pulse energy and duration as a function of launched power, which are measured by the photodiode with resolution ~2 ns. The pulse energy (Jpul) was calculated from the pulse repetition rate (frep) and the average output power (Pave) following the equation below:

Jpul=Pavefrep
(1)

Far from the threshold, the pulse energy increases and finally saturates to ~13.4 nJ. Similarly, the pulse width of the Q-switched waveguide laser becomes constant (~22 ns) with high pump powers. Near the threshold, the value of pulse energy and width was tuned by the pump power. In this waveguide structure, the relaxation oscillation was observed with the pumping power near the threshold. Hence, we believe the unstable output of laser near the threshold could be attributed to the relaxation oscillation effect.

The model for passively Q-switched laser has been demonstrated in [21

21. J. J. Zayhowski and P. L. Kelley, “Optimization of Q-switched Lasers,” IEEE J. Quantum Electron. 27(9), 2220–2225 (1991). [CrossRef]

] and [22

22. G. J. Spühler, R. Paschotta, R. Fluck, B. Braun, M. Moser, G. Zhang, E. Gini, and U. Keller, “Experimentally confirmed design guidelines for passively Q-switched microchip lasers using semiconductor saturable absorbers,” J. Opt. Soc. Am. B 16(3), 376–388 (1999). [CrossRef]

]. Based on their argument, the equations for the pulse width and pulse energy could be expressed as below:

EphvLσLAΔRηout
(2)
τp3.52TRΔR
(3)

where Ep is the pulse energy; hvL is the photon energy at the lasing wavelength; σL is the emission cross section of the laser material; A is the cross section of pumped volume; ΔR is the modulation depth of the SESAM; ηout is the output coupling efficiency; τp is the pulse duration; TR is the cavity round-trip time. As one can see, all the parameters are decided by the material (hvL, σL) and the structure of waveguide (A, ΔR, TR, ηout), which are constants for a certain waveguide. Hence, the pulse width and pulse energy are independent of the pump power and become constant values at high pumping power, which has a very good agreement with our experiment results.

4. Conclusions

In conclusion, Q-switching pulsed laser generation was realized in double-cladding Nd:YAG ceramics waveguides with a SESAM as output mirror. Symmetrical single mode laser oscillation was observed at the wavelength of 1064 nm. The pulsed laser oscillation threshold was 47 mW for the 30 μm inner core waveguides. The maximum repetition rate and average power achieved were 3.65 MHz and 48 mW respectively.

Acknowledgments

This work is carried out under the support by the National Natural Science Foundation of China (No. 10925524) and the Spanish Ministerio de Ciencia e Innovación (Projects CSD2007-00013 and FIS2009-09522), and Junta de Castilla y León (Project SA086A12-2). Tan acknowledges Independent Innovation Foundation of Shandong University (IIFSDU, No. 104222012GN056 / 11160072614098) and China Postdoctoral Science Foundation (Grant No. 2013M530316). Feng-Qin Liu acknowledges Award Fund for Excellent Young and Middle-aged Scientists of Shandong Province (BS2011DX020).

References and links

1.

A. Ikesue and Y. L. Aung, “Ceramic laser materials,” Nat. Photonics 2(12), 721–727 (2008). [CrossRef]

2.

Y. Chen, W. Liu, Y. Bo, B. Jiang, J. Xu, J. Li, Y. Xu, Y. Pan, J. L. Xu, X. Feng, Y. Guo, Y. Shen, F. Yang, L. Yuan, H. Yuan, Q. Peng, D. Cui, and Z. Xu, “High-efficiency high-power QCW diode-side-pumped zigzag Nd:YAG ceramic slab laser,” Appl. Phys. B 111(1), 111–116 (2013). [CrossRef]

3.

S. Men, Z. Liu, X. Zhang, Q. Wang, H. Shen, F. Bai, L. Gao, X. Xu, R. Wei, and X. Chen, “A graphene passively Q-switched Nd:YAG ceramic laser at 1123 nm,” Laser Phys. Lett. 10(3), 035803 (2013). [CrossRef]

4.

G. Xie, D. Tang, J. Kong, and L. Qian, “Passive mode-locking of a Nd:YAG ceramic laser by optical interference modulation in a GaAs wafer,” Opt. Express 15(9), 5360–5365 (2007). [CrossRef] [PubMed]

5.

G. A. Torchia, P. F. Meilán, A. Rodenas, D. Jaque, C. Mendez, and L. Roso, “Femtosecond laser written surface waveguides fabricated in Nd:YAG ceramics,” Opt. Express 15(20), 13266–13271 (2007). [CrossRef] [PubMed]

6.

Y. Tan and F. Chen, “Proton-implanted optical channel waveguides in Nd:YAG laser ceramics,” J. Phys. D Appl. Phys. 43(7), 075105 (2010). [CrossRef]

7.

F. Chen and J. R. Vázquez de Aldana, “Optical waveguides in crystalline dielectric materials produced by femtosecond-laser micromachining,” Laser Photonics Rev. (Wiley online early view) DOI: [CrossRef]

8.

M. Ams, G. D. Marshall, P. Dekker, J. A. Piper, and M. J. Withford, “Ultrafast laser written active devices,” Laser Photonics Rev. 3(6), 535–544 (2009). [CrossRef]

9.

C. Grivas, “Optically pumped planar waveguide lasers, Part I: Fundamentals and fabrication techniques,” Prog. Quantum Electron. 35(6), 159–239 (2011). [CrossRef]

10.

Y. Tan, Q. Luan, F. Liu, S. Akhmadaliev, S. Zhou, and F. Chen, “Swift carbon ion irradiated Nd:YAG ceramic optical waveguide amplifier,” Opt. Express 21(12), 13992–13997 (2013). [CrossRef] [PubMed]

11.

F. M. Bain, W. F. Silva, A. A. Lagatsky, R. R. Thomson, N. D. Psaila, A. K. Kar, W. Sibbett, D. Jaque, and C. T. A. Brown, “Microspectroscopy of ultrafast laser inscribed channel waveguides in Yb:tungstate crystals,” Appl. Phys. Lett. 98(14), 141108 (2011). [CrossRef] [PubMed]

12.

Y. L. Lee, N. E. Yu, C. Jung, B.-A. Yu, I.-B. Sohn, S.-C. Choi, Y.-C. Noh, D.-K. Ko, W.-S. Yang, H.-M. Lee, W.-K. Kim, and H.-Y. Lee, “Second-harmonic generation in periodically poled lithium niobate waveguides fabricated by femtosecond laser pulses,” Appl. Phys. Lett. 89(17), 171103 (2006). [CrossRef]

13.

T. Calmano, A.-G. Paschke, J. Siebenmorgen, S. T. Fredrich-Thornton, H. Yagi, K. Petermann, and G. Huber, “Characterization of an Yb:YAG ceramic waveguide laser, fabricated by the direct femtosecond-laser writing technique,” Appl. Phys. B 103(1), 1–4 (2011). [CrossRef]

14.

H. Liu, Y. Jia, J. R. Vázquez de Aldana, D. Jaque, and F. Chen, “Femtosecond laser inscribed cladding waveguides in Nd:YAG ceramics: Fabrication, fluorescence imaging and laser performance,” Opt. Express 20(17), 18620–18629 (2012). [CrossRef] [PubMed]

15.

Y. Jia, J. R. Vázquez de Aldana, and F. Chen, “Efficient waveguide lasers in femtosecond laser inscribed double-cladding waveguides of Yb:YAG ceramics,” Opt. Mater. Express 3(5), 645–650 (2013). [CrossRef]

16.

D. J. Richardson, J. Nilsson, and W. A. Clarkson, “High power fiber lasers: current status and future perspectives,” J. Opt. Soc. Am. B 27(11), B63–B92 (2010). [CrossRef]

17.

A. Okhrimchuk, “Femtosecond fabrication of waveguides in ion-doped laser crystal,” in Coherence and Ultrashort Pulse Laser Emission, F. J. Duarte, ed., (InTech, 2010).

18.

T. Calmano, A.-G. Paschke, S. Mueller, C. Kraenkel, and G. Huber, “Q-Switched Operation of a fs-Laser Written Nd:YAG/Cr4+:YAG Monolithic Waveguide Laser,” in OSA Technical Digest Series (CD) (Optical Society of America, 2012), paper IF2A.4.

19.

A. G. Okhrimchuk, V. K. Mezentsev, V. V. Dvoyrin, A. S. Kurkov, E. M. Sholokhov, S. K. Turitsyn, A. V. Shestakov, and I. Bennion, “Waveguide-saturable absorber fabricated by femtosecond pulses in YAG:Cr4+ crystal for Q-switched operation of Yb-fiber laser,” Opt. Lett. 34(24), 3881–3883 (2009). [CrossRef] [PubMed]

20.

J. Siebenmorgen, T. Calmano, K. Petermann, and G. Huber, “Highly efficient Yb:YAG channel waveguide laser written with a femtosecond-laser,” Opt. Express 18(15), 16035–16041 (2010). [CrossRef] [PubMed]

21.

J. J. Zayhowski and P. L. Kelley, “Optimization of Q-switched Lasers,” IEEE J. Quantum Electron. 27(9), 2220–2225 (1991). [CrossRef]

22.

G. J. Spühler, R. Paschotta, R. Fluck, B. Braun, M. Moser, G. Zhang, E. Gini, and U. Keller, “Experimentally confirmed design guidelines for passively Q-switched microchip lasers using semiconductor saturable absorbers,” J. Opt. Soc. Am. B 16(3), 376–388 (1999). [CrossRef]

OCIS Codes
(140.3540) Lasers and laser optics : Lasers, Q-switched
(160.5690) Materials : Rare-earth-doped materials
(230.7380) Optical devices : Waveguides, channeled

ToC Category:
Lasers and Laser Optics

History
Original Manuscript: June 24, 2013
Revised Manuscript: July 24, 2013
Manuscript Accepted: July 25, 2013
Published: August 1, 2013

Citation
Yang Tan, Qingfang Luan, Fengqin Liu, Feng Chen, and Javier Rodríguez Vázquez de Aldana, "Q-switched pulse laser generation from double-cladding Nd:YAG ceramics waveguides," Opt. Express 21, 18963-18968 (2013)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-21-16-18963


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. A. Ikesue and Y. L. Aung, “Ceramic laser materials,” Nat. Photonics2(12), 721–727 (2008). [CrossRef]
  2. Y. Chen, W. Liu, Y. Bo, B. Jiang, J. Xu, J. Li, Y. Xu, Y. Pan, J. L. Xu, X. Feng, Y. Guo, Y. Shen, F. Yang, L. Yuan, H. Yuan, Q. Peng, D. Cui, and Z. Xu, “High-efficiency high-power QCW diode-side-pumped zigzag Nd:YAG ceramic slab laser,” Appl. Phys. B111(1), 111–116 (2013). [CrossRef]
  3. S. Men, Z. Liu, X. Zhang, Q. Wang, H. Shen, F. Bai, L. Gao, X. Xu, R. Wei, and X. Chen, “A graphene passively Q-switched Nd:YAG ceramic laser at 1123 nm,” Laser Phys. Lett.10(3), 035803 (2013). [CrossRef]
  4. G. Xie, D. Tang, J. Kong, and L. Qian, “Passive mode-locking of a Nd:YAG ceramic laser by optical interference modulation in a GaAs wafer,” Opt. Express15(9), 5360–5365 (2007). [CrossRef] [PubMed]
  5. G. A. Torchia, P. F. Meilán, A. Rodenas, D. Jaque, C. Mendez, and L. Roso, “Femtosecond laser written surface waveguides fabricated in Nd:YAG ceramics,” Opt. Express15(20), 13266–13271 (2007). [CrossRef] [PubMed]
  6. Y. Tan and F. Chen, “Proton-implanted optical channel waveguides in Nd:YAG laser ceramics,” J. Phys. D Appl. Phys.43(7), 075105 (2010). [CrossRef]
  7. F. Chen and J. R. Vázquez de Aldana, “Optical waveguides in crystalline dielectric materials produced by femtosecond-laser micromachining,” Laser Photonics Rev. (Wiley online early view) DOI: [CrossRef]
  8. M. Ams, G. D. Marshall, P. Dekker, J. A. Piper, and M. J. Withford, “Ultrafast laser written active devices,” Laser Photonics Rev.3(6), 535–544 (2009). [CrossRef]
  9. C. Grivas, “Optically pumped planar waveguide lasers, Part I: Fundamentals and fabrication techniques,” Prog. Quantum Electron.35(6), 159–239 (2011). [CrossRef]
  10. Y. Tan, Q. Luan, F. Liu, S. Akhmadaliev, S. Zhou, and F. Chen, “Swift carbon ion irradiated Nd:YAG ceramic optical waveguide amplifier,” Opt. Express21(12), 13992–13997 (2013). [CrossRef] [PubMed]
  11. F. M. Bain, W. F. Silva, A. A. Lagatsky, R. R. Thomson, N. D. Psaila, A. K. Kar, W. Sibbett, D. Jaque, and C. T. A. Brown, “Microspectroscopy of ultrafast laser inscribed channel waveguides in Yb:tungstate crystals,” Appl. Phys. Lett.98(14), 141108 (2011). [CrossRef] [PubMed]
  12. Y. L. Lee, N. E. Yu, C. Jung, B.-A. Yu, I.-B. Sohn, S.-C. Choi, Y.-C. Noh, D.-K. Ko, W.-S. Yang, H.-M. Lee, W.-K. Kim, and H.-Y. Lee, “Second-harmonic generation in periodically poled lithium niobate waveguides fabricated by femtosecond laser pulses,” Appl. Phys. Lett.89(17), 171103 (2006). [CrossRef]
  13. T. Calmano, A.-G. Paschke, J. Siebenmorgen, S. T. Fredrich-Thornton, H. Yagi, K. Petermann, and G. Huber, “Characterization of an Yb:YAG ceramic waveguide laser, fabricated by the direct femtosecond-laser writing technique,” Appl. Phys. B103(1), 1–4 (2011). [CrossRef]
  14. H. Liu, Y. Jia, J. R. Vázquez de Aldana, D. Jaque, and F. Chen, “Femtosecond laser inscribed cladding waveguides in Nd:YAG ceramics: Fabrication, fluorescence imaging and laser performance,” Opt. Express20(17), 18620–18629 (2012). [CrossRef] [PubMed]
  15. Y. Jia, J. R. Vázquez de Aldana, and F. Chen, “Efficient waveguide lasers in femtosecond laser inscribed double-cladding waveguides of Yb:YAG ceramics,” Opt. Mater. Express3(5), 645–650 (2013). [CrossRef]
  16. D. J. Richardson, J. Nilsson, and W. A. Clarkson, “High power fiber lasers: current status and future perspectives,” J. Opt. Soc. Am. B27(11), B63–B92 (2010). [CrossRef]
  17. A. Okhrimchuk, “Femtosecond fabrication of waveguides in ion-doped laser crystal,” in Coherence and Ultrashort Pulse Laser Emission, F. J. Duarte, ed., (InTech, 2010).
  18. T. Calmano, A.-G. Paschke, S. Mueller, C. Kraenkel, and G. Huber, “Q-Switched Operation of a fs-Laser Written Nd:YAG/Cr4+:YAG Monolithic Waveguide Laser,” in OSA Technical Digest Series (CD) (Optical Society of America, 2012), paper IF2A.4.
  19. A. G. Okhrimchuk, V. K. Mezentsev, V. V. Dvoyrin, A. S. Kurkov, E. M. Sholokhov, S. K. Turitsyn, A. V. Shestakov, and I. Bennion, “Waveguide-saturable absorber fabricated by femtosecond pulses in YAG:Cr4+ crystal for Q-switched operation of Yb-fiber laser,” Opt. Lett.34(24), 3881–3883 (2009). [CrossRef] [PubMed]
  20. J. Siebenmorgen, T. Calmano, K. Petermann, and G. Huber, “Highly efficient Yb:YAG channel waveguide laser written with a femtosecond-laser,” Opt. Express18(15), 16035–16041 (2010). [CrossRef] [PubMed]
  21. J. J. Zayhowski and P. L. Kelley, “Optimization of Q-switched Lasers,” IEEE J. Quantum Electron.27(9), 2220–2225 (1991). [CrossRef]
  22. G. J. Spühler, R. Paschotta, R. Fluck, B. Braun, M. Moser, G. Zhang, E. Gini, and U. Keller, “Experimentally confirmed design guidelines for passively Q-switched microchip lasers using semiconductor saturable absorbers,” J. Opt. Soc. Am. B16(3), 376–388 (1999). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1 Fig. 2 Fig. 3
 
Fig. 4 Fig. 5
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited