OSA's Digital Library

Optics Express

Optics Express

  • Editor: Andrew M. Weiner
  • Vol. 21, Iss. 22 — Nov. 4, 2013
  • pp: 26227–26235
« Show journal navigation

Digitally tunable holographic lithography using a spatial light modulator as a programmable phase mask

J. Lutkenhaus, D. George, M. Moazzezi, U. Philipose, and Y. Lin  »View Author Affiliations


Optics Express, Vol. 21, Issue 22, pp. 26227-26235 (2013)
http://dx.doi.org/10.1364/OE.21.026227


View Full Text Article

Acrobat PDF (3812 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

In this paper, we study tunable holographic lithography using an electrically addressable spatial light modulator as a programmable phase mask. We control the phases of interfering beams diffracted from the phase pattern displayed in the spatial light modulator. We present a calculation method for the assignment of phases in the laser beams and validate the phases of the interfering beams in phase-sensitive, dual-lattice, and two-dimensional patterns formed by a rotationally non-symmetrical configuration. A good agreement has been observed between fabricated holographic structures and simulated interference patterns. The presented method can potentially help design a gradient phase mask for the fabrication of graded photonic crystals or metamaterials.

© 2013 Optical Society of America

1. Introduction

Periodic photonic structures such as photonic crystals (PhCs) provide new opportunities in device applications for the control and manipulation of photons [1

1. S. John, “Strong localization of photons in certain disordered dielectric superlattices,” Phys. Rev. Lett. 58(23), 2486–2489 (1987). [CrossRef] [PubMed]

,2

2. E. Yablonovitch, “Inhibited spontaneous emission in Solid-State Physics and Electronics,” Phys. Rev. Lett. 58(20), 2059–2062 (1987). [CrossRef] [PubMed]

]. One-dimensional PhCs such as fiber Bragg gratings have been fabricated in optical fiber, using phase mask based two-beam interference, for applications in fiber optical communications [3

3. K. P. Chen, P. R. Herman, and R. Tam, “Strong fiber Bragg grating fabrication by hybrid 157- and 248-nm laser exposure,” IEEE Photon. Technol. Lett. 14(2), 170–172 (2002). [CrossRef]

]. Two-dimensional PhCs have been used for the integrated laser on chip [4

4. S. Noda, M. Yokoyama, M. Imada, A. Chutinan, and M. Mochizuki, “Polarization mode control of two-dimensional photonic crystal laser by unit cell structure design,” Science 293(5532), 1123–1125 (2001). [CrossRef] [PubMed]

] and all-optical circuit [5

5. Y. Liu, F. Qin, Z.-M. Meng, F. Zhou, Q.-H. Mao, and Z.-Y. Li, “All-optical logic gates based on two-dimensional low-refractive-index nonlinear photonic crystal slabs,” Opt. Express 19(3), 1945–1953 (2011). [CrossRef] [PubMed]

]. Low threshold lasers in three-dimensional PhCs have been observed in PhC nanocavities [6

6. A. Tandaechanurat, S. Ishida, D. Guimard, M. Nomura, S. Iwamoto, and Y. Arakawa, “Lasing oscillation in a three-dimensional photonic crystal nanocavity with a complete bandgap,” Nat. Photonics 5(2), 91–94 (2011). [CrossRef]

]. Various fabrication methods have been used for making PhCs, such as e-beam lithography [7

7. K. M. Ho, C. T. Chan, C. M. Soukoulis, R. Biswas, and M. Sigalas, “Photonic band gaps in three dimensions: new layer-by-layer periodic structures,” Solid State Commun. 89(5), 413–416 (1994). [CrossRef]

], self-assembly of colloidal microspheres [8

8. A. Blanco, E. Chomski, S. Grabtchak, M. Ibisate, S. John, S. W. Leonard, C. Lopez, F. Meseguer, H. Miguez, J. P. Mondia, G. A. Ozin, O. Toader, A. Geoffrey, O. Toader, and H. M. van Driel, “Large-scale synthesis of a silicon photonic crystal with a complete three-dimensional bandgap near 1.5 micrometres,” Nature 405(6785), 437–440 (2000). [CrossRef] [PubMed]

], two-photon lithography [9

9. M. Deubel, G. von Freymann, M. Wegener, S. Pereira, K. Busch, and C. M. Soukoulis, “Direct laser writing of three-dimensional photonic-crystal templates for telecommunications,” Nat. Mater. 3(7), 444–447 (2004). [CrossRef] [PubMed]

], and laser holographic lithography [10

10. M. Campbell, D. N. Sharp, M. T. Harrison, R. G. Denning, and A. J. Turberfield, “Fabrication of photonic crystals for the visible spectrum by holographic lithography,” Nature 404(6773), 53–56 (2000). [CrossRef] [PubMed]

,11

11. S. Yang, M. Megens, J. Aizenberg, P. Wiltzius, P. M. Chaikin, and W. B. Russel, “Creating periodic three-dimensional structures by multibeam interference of visible laser,” Chem. Mater. 14(7), 2831–2833 (2002). [CrossRef]

].

Multi-beam interferences can generate one, two or three dimensional patterns and have been used for fabricating a large number of photonic devices such as gratings and PhCs [3

3. K. P. Chen, P. R. Herman, and R. Tam, “Strong fiber Bragg grating fabrication by hybrid 157- and 248-nm laser exposure,” IEEE Photon. Technol. Lett. 14(2), 170–172 (2002). [CrossRef]

,10

10. M. Campbell, D. N. Sharp, M. T. Harrison, R. G. Denning, and A. J. Turberfield, “Fabrication of photonic crystals for the visible spectrum by holographic lithography,” Nature 404(6773), 53–56 (2000). [CrossRef] [PubMed]

15

15. D. Xu, K. P. Chen, A. Harb, D. Rodriguez, K. Lozano, and Y. Lin, “Phase tunable holographic fabrication for three-dimensional photonic crystal templates by using a single optical element,” Appl. Phys. Lett. 94(23), 231116 (2009).

]. The optical setup for a precise interference pattern is usually complicated if bulky mirrors, polarizers, and beam splitters are used [10

10. M. Campbell, D. N. Sharp, M. T. Harrison, R. G. Denning, and A. J. Turberfield, “Fabrication of photonic crystals for the visible spectrum by holographic lithography,” Nature 404(6773), 53–56 (2000). [CrossRef] [PubMed]

,11

11. S. Yang, M. Megens, J. Aizenberg, P. Wiltzius, P. M. Chaikin, and W. B. Russel, “Creating periodic three-dimensional structures by multibeam interference of visible laser,” Chem. Mater. 14(7), 2831–2833 (2002). [CrossRef]

]. Using a static phase mask as a multi-beam generation tool can replace a large number of bulk optical elements for the same purpose. Static diffractive (phase mask) or deflective optical elements have successfully been used for the generation of one, two and three dimensional patterns [11

11. S. Yang, M. Megens, J. Aizenberg, P. Wiltzius, P. M. Chaikin, and W. B. Russel, “Creating periodic three-dimensional structures by multibeam interference of visible laser,” Chem. Mater. 14(7), 2831–2833 (2002). [CrossRef]

16

16. T. Y. M. Chan, O. Toader, and S. John, “Photonic band-gap formation by optical-phase-mask lithography,” Phys. Rev. E Stat. Nonlin. Soft Matter Phys. 73(4), 046610 (2006). [CrossRef] [PubMed]

]. A phase tuning of interfering beams is sometimes necessary in order to generate a desired interference pattern [14

14. K. Ohlinger, H. Zhang, Y. Lin, D. Xu, and K. P. Chen, “A tunable three layer phase mask for single laser exposure 3D photonic crystal generations: bandgap simulation and holographic fabrication,” Opt. Mater. Express 1(5), 1034–1039 (2011). [CrossRef]

,15

15. D. Xu, K. P. Chen, A. Harb, D. Rodriguez, K. Lozano, and Y. Lin, “Phase tunable holographic fabrication for three-dimensional photonic crystal templates by using a single optical element,” Appl. Phys. Lett. 94(23), 231116 (2009).

]. Very recently, spatial light modulators (SLMs) encoded with computer-generated-holograms or patterns have been used for the holographic fabrication of complex periodic or quasi-periodic photonic structures [17

17. G. Zito, B. Piccirillo, E. Santamato, A. Marino, V. Tkachenko, and G. Abbate, “Two-dimensional photonic quasicrystals by single beam computer-generated holography,” Opt. Express 16(8), 5164–5170 (2008). [CrossRef] [PubMed]

19

19. V. Arrizón, D. S. de-la-Llave, G. Méndez, and U. Ruiz, “Efficient generation of periodic and quasi-periodic non-diffractive optical fields with phase holograms,” Opt. Express 19(11), 10553–10562 (2011). [CrossRef] [PubMed]

]. By engineering the phase pattern, the phase of individual interfering beams can be designed for helically stacked multi-layered microrotors realized in vortex-embedded three dimensional optical twister patterns [20

20. J. Xavier, R. Dasgupta, S. Ahlawat, J. Joseph, and P. K. Gupta, “Three dimensional optical twisters-driven helically stacked multi-layered microrotors,” Appl. Phys. Lett. 100(12), 121101 (2012). [CrossRef]

] or for the formation of photonic chiral photonic lattices [21

21. J. Xavier and J. Joseph, “Tunable complex photonic chiral lattices by reconfigurable optical phase engineering,” Opt. Lett. 36(3), 403–405 (2011). [CrossRef] [PubMed]

]. Usually the first order was chosen by the Fourier filter for the reconstruction of the desired pattern. By embedding nondiffracting defect sites [22

22. M. Kumar and J. Joseph, “Embedding a nondiffracting defect site in helical lattice wave-field by optical phase engineering,” Appl. Opt. 52(23), 5653–5658 (2013). [CrossRef] [PubMed]

] or including higher Fourier orders in the phase pattern [23

23. M. Boguslawski, A. Kelberer, P. Rose, and C. Denz, “Multiplexing complex two-dimensional photonic superlattices,” Opt. Express 20(24), 27331–27343 (2012). [CrossRef] [PubMed]

], simultaneous fabrication of functional defects in photonic lattices can be achieved [22

22. M. Kumar and J. Joseph, “Embedding a nondiffracting defect site in helical lattice wave-field by optical phase engineering,” Appl. Opt. 52(23), 5653–5658 (2013). [CrossRef] [PubMed]

] or multiperiodic staircase lattice can be formed [23

23. M. Boguslawski, A. Kelberer, P. Rose, and C. Denz, “Multiplexing complex two-dimensional photonic superlattices,” Opt. Express 20(24), 27331–27343 (2012). [CrossRef] [PubMed]

]. On the other hand, the recent appearance of transformation optics theory [24

24. J. B. Pendry, D. Schurig, and D. R. Smith, “Controlling electromagnetic fields,” Science 312(5781), 1780–1782 (2006). [CrossRef] [PubMed]

,25

25. U. Leonhardt, “Optical conformal mapping,” Science 312(5781), 1777–1780 (2006). [CrossRef] [PubMed]

] can address the inverse problem of electromagnetism with respect to what nanostructures will perform a requested functionality. Theoretically, transformation optics can prescribe the path of light in nanostructures at will, by controlling the index of refraction as a function of position, potentially to any desired profile [24

24. J. B. Pendry, D. Schurig, and D. R. Smith, “Controlling electromagnetic fields,” Science 312(5781), 1780–1782 (2006). [CrossRef] [PubMed]

,25

25. U. Leonhardt, “Optical conformal mapping,” Science 312(5781), 1777–1780 (2006). [CrossRef] [PubMed]

]. Using a SLM, it is possible to generate a gradient refractive index in holographic structures by controlling the local filling factor of the dielectric material where the filling factor is controlled by the phase of the interfering beams [26

26. B. Arigong, K. Ohlinger, H. S. Kim, Y. Lin, and H. Zhang, “Transformation optics designed general optical luneburg lens with flattened shapes,” Proc. SPIE 8376, 83760R–1, 83760R-6 (2012). [CrossRef]

,27

27. K. Ohlinger, J. Lutkenhaus, H. Zhang, and Y. Lin, “Spatially addressable design of Luneburg lens through spatial light modulator based holographic lithography,” J. Appl. Phys. submitted.

]. From a designer’s point of view, it is necessary to have a mathematical formula that can calculate the phase of interfering beams from the gray levels or gradient gray levels in the SLM for the design and fabrication of transformation optics devices [26

26. B. Arigong, K. Ohlinger, H. S. Kim, Y. Lin, and H. Zhang, “Transformation optics designed general optical luneburg lens with flattened shapes,” Proc. SPIE 8376, 83760R–1, 83760R-6 (2012). [CrossRef]

,27

27. K. Ohlinger, J. Lutkenhaus, H. Zhang, and Y. Lin, “Spatially addressable design of Luneburg lens through spatial light modulator based holographic lithography,” J. Appl. Phys. submitted.

].

In this paper, we worked out detailed calculation formulas showing how the gray scale value in the displayed pattern in SLM is converted to tune the phase of diffracted beams. The study was performed in an interference pattern that has a visually observable phase-dependent dual-lattice structure. We were able to digitally assign the phase for interfering beams when the laser beam was modulated by the programmed phase pattern displayed in the SLM. This phase assignment method was validated by comparing the fabricated holographic structures with theoretical simulations.

2. Experimental setup

The experimental setup for the interference lithography is shown in Fig. 1
Fig. 1 Scheme of experimental optics setup using the SLM for multi-beam interference lithography. Phase pattern was displayed on the SLM. Imaging lenses f1 and f2 were arranged in a 4f configuration.
. A 532 nm laser beam (Cobolt Samba) was expanded, collimated, and reflected by an SLM (Holoeye Pluto phase-only SLM). A phase pattern as a dynamic phase mask was displayed on the SLM, and the wavefront of the reflected laser beam was modulated by the SLM. The interfering pattern was transferred and de-magnified through a 4f imaging system (f1 = 400 mm and f2 = 200 mm). Further demagnification was realized using a focusing objective lens. A thin film sample or CCD camera was mounted in a translational stage for the holographic fabrication or image recording, respectively.

3. Design of programmable phase mask and test of phase control capability

Figure 2(b) shows the diffraction pattern after the laser beam was diffracted by the phase pattern in SLM and focused by the first lens as shown in Fig. 1. The diffraction pattern was recorded by a CCD camera (Edmund Optics). Surrounding the 0th order diffraction in the center, the six 1st order diffraction beams exhibited hexagonal symmetry. Outside the 1st order diffraction, 2nd and higher order diffractions were recorded. These diffraction spots were also at the vertices of hexagons. The recorded diffraction pattern looked very similar to the one predicted in Fig. 2(a). The designed side length of equilateral triangles was 0.706 mm. The displayed pattern in SLM was zoomed to 3.12% of the original. Thus the side length became 22.0 μm. From the diffraction pattern, we calculated the side length of the equilateral triangle in Fig. 2(a) to be 22.1 μm, which is very close to the designed value.

Based on the fact that the symmetry and location of the predicted diffraction pattern were the same as the experimentally observed one, we drew a hexagonal unit cell (hexagon in red lines) in the Fig. 2(c) for the phase pattern in Fig. 2(a) and assigned phases for each first-order diffracted beam using the pre-assigned gray levels. The hexagon was divided into six equal areas, and each area formed a kite-type four-sided polygon. Each kite had the same area as a light gray or dark grey triangle in Fig. 2(c). The phases of the diffracted beams at the head of each kite were determined by the overall gray level covered by the kite. The phases of beams 1, 3 and 5 in Fig. 2(c) should be the same because their phases were determined by the same gray level which is

13 light gray+818 black+118 black+ 16 black,  
(1)

The phases of beams 2, 4 and 6 were determined by the same gray level which is

13 dark grey+818 black+118 black+ 16 black,  
(2)

ΔI(r)=E1E3e1e3cos[2π((3/a)i(1/b)j)(x+y)+(δ3δ1)]+E1E5e1e5cos[2π((3/a)i+(1/b)j)(x+y)+(δ5δ1)]+E1E4e1e4cos[2π((4/a)i+0j)(x+y)+(δ4δ1)]+E3E5e3e5cos[2π((0i+(2/b)j)(x+y)+(δ5δ3)]+E3E4e3e4cos[2π((1/a)i+(1/b)j)(x+y)+(δ4δ3)]+E5E4e5e4cos[2π((1/a)i(1/b)j)(x+y)+(δ4δ5)],
(4)

Where a and b are the lattice constants of the interference pattern in x and y directions, respectively, as shown in Fig. (3)
Fig. 3 (a1, b1, c1) A scheme of an enlarged view of designed patterns with a gray level in a set of triangles changed from 153 to 102 and to 51. The hexagon indicates the unit cell of the designed pattern. (a2, b2, c2) CCD recorded images for four-beam interference pattern from beams 1, 3, 4 and 5 diffracted from phase patterns in (a1, b1, c1), respectively. (a3, b3, c3) Simulated four-beam interference pattern formed by beams 1, 3, 4 and 5 with phases assignments from the gray levels in (a1, b1, c1), respectively. Labels a and b in (a3) indicates the lattice constants and red arrows in (b3) indicate the pattern shifting directions. (a4, b4, c4) 3D view of simulated four-beam interference patterns given in (a3, b3, c3).
, and δ is the initial phase which is determined by Eq. (1) and Eq. (2).

Figure 3(a1) shows a portion of a programmed pattern where the gray level in the equilateral triangles was set to be 153, or 0 for black. In Figs. 3(b1) and 3(c1), the gray level in one set of equilateral triangles was adjusted to be 102 and 51, respectively. When these patterns were displayed on the SLM, the gray level was converted into a phase level based on the gamma curve used. The gamma curve can convert the gray level between 0 and 255 into a phase level between 0 and 2π, respectively. The phase for beams 1, 3 and 5 was the same in all Figs. 3(a1, b1, c1). The phase of beams 2, 4 and 6 in Figs. 3(b1) and 3(c) became smaller than the one in Fig. 3(a1). Based on the Eq. (3) and Eq. (4), the interference pattern involving beam 4 will have a pattern shift if beam 4 has a relative phase shift of 0.13 π and 0.27 π in Figs. 3(b) and 3(c), respectively:

ΔI(relatedtobeam4)=E1E4e1e4cos[2π((4/a)i+0j)(x+y)mπ]+E3E4e3e4cos[2π((1/a)i+(1/b)j)(x+y)mπ]+E5E4e5e4cos[2π((1/a)i(1/b)j)(x+y)mπ]=E1E4e1e4cos[2π((4/a)i+0j)(x+y+m(18a±38b))]+E3E4e3e4cos[2π((1/a)i+(1/b)j)(x+y+m(18a38b))]+E5E4e5e4cos[2π((1/a)i(1/b)j)(x+y+m(18a+38b))],
(5)

Where m = 0.13 or 0.27. The phase change in beam 4 will shift the portion of the interference pattern in the (−1, 3) or (−1, −3) directions, as shown in Fig. 3. Figure 3(a2,b2,c2) shows the recorded CCD images of four-beam interference patterns formed by beams 1, 3, 4, and 5. The change of the interference pattern from Fig. 3(a2) to 3(b2) to 3(c2) was very clearly recorded. The interference pattern changed from fenced cylinder structures in Fig. 3(a2) to paired dual-lattice structures (dumbbell at each lattice), indicating the phase control capability in using the SLM as a phase mask.

Figures 3(a3,b3,c3,a4,b4,c4) are 2D and 3D views of simulated four-beam interference patterns assuming the relative phases of interfering beams are determined by Eqs. (1) and (2). These patterns clearly show the structural changes in the figures when the gray level in one set of triangles was changed from 153 to 102, and further to 51. The intensity strength was shifted to other regions in the (−1,3) or (−1,-3) directions as indicated in Fig. 3(b3).The simulated patterns in Fig. 3(c) are very similar to the CCD recorded patterns in Fig. 3(b), approving the phase determination by Eqs. (1) and (2).

4. Holographic fabrication

As a proof of concept, we fabricated the holographic structures formed by interfering four beams diffracted from the phase pattern displayed in Fig. 3(a1). The total laser (532 nm) power was 50 mW. The photoresist was photo-sensitized to 532 nm by preparing a mixture with the following components in the specified weight concentrations: dipentaerythritol penta/hexaacrylate (DPHPA) monomer (Aldrich, 90.36%), a photo initiator rose bengal (0.11%), co-initiator N-phenyl glycine (NPG, 0.65%), and chain extender N-vinyl pyrrolidinone (NVP, 8.88%). The mixture was spin-coated on a glass slide with a speed of 3000 rpm for 30 seconds. The film thickness was approximately 3.17 microns. The photoresist film was exposed to the interference pattern for a typical exposure time of 2 seconds. The exposed sample was developed in PGMEA for 3 minutes, rinsed by isopropanol for one minute and left to dry in air.

Figures 4
Fig. 4 (a1,a2,a3) CCD images of interference patterns recorded at different locations longitudinally translated along z-direction by 0, 127, and 254 microns. (b) SEM image of fabricated holographic structures in DPHPA. (c) An enlarged view of the SEM in (b). (d) Atomic force microscope image of the fabricated holographic structures in DPHPA. (e) A surface profile measured along the line in the AFM image in (d).
(a1,a2,a3) show the CCD image of the interference patterns recorded at different locations. No changes are observed as the interference pattern is a 2D periodic structure. Figure 4(b) shows a scanning electron microscope (SEM) image of the holographically formed photonic structures in DPHPA. An enlarged view of the SEM is shown in Fig. 4(c). Because the photoresist, DPHPA, is in liquid form, aggregation during polymerization might cause the dome shape in the fabricated structure’s surface. Figure 4(d) shows atomic force microscope (AFM) image of the fabricated structures in DPHPA. The agreement among these SEM, AFM images, CCD recorded images, and simulated pattern in Fig. 3(a3) is very good. A surface profile along the line in the AFM is shown in Fig. 4(e), and the lattice period along the red line in Fig. 4(d) is measured to be 4.07 microns. By comparing the period of the CCD recorded patterns with and without the objective lens, a de-magnification of 4.1 was observed. The interfering angle after lens 2 was measured to 1.83 degrees. Based on the de-magnification factor, a theoretical calculation gave a lattice constant of 4.06 microns. The agreement between measured and theoretical values is very good.

5. Discussion

We can test phase formulas of Eq. (1) and Eq. (2) in a more complicated phase mask where six triangles in the hexagon are assigned with different gray levels. As an example, Fig. 5(a)
Fig. 5 (a) A scheme of an enlarged view of a designed pattern with different gray levels in triangles from a to f. The gray levels are labeled in the right side of the pattern. The hexagon indicates the unit cell of the designed pattern. (b) Simulated four-beam interference pattern using the phase information in (a). Inset is a 3D view. (c) CCD recorded images for four-beam interference pattern from beams diffracted from phase patterns in (a). (d) SEM image of fabricated holographic structures in DPHPA. (e, f, g) Simulated four-beam interference patterns formed by beams 1, 3, 4 and 5 with phases assignments from the gray levels shown in Fig. 3(a1, b1, c1), respectively. The patterns were obtained by setting the iso-intensity surface to be a half of maximum intensity.
shows a portion of a programmed pattern where the gray level in the equilateral triangles (from a-f) were set to be 255, 202, 150, 99, 49, and 0, respectively. Figure 5(b) is a simulated interference pattern by diffracted beams (1, 3, 4, 5) using phases determined by a similar way as shown in Fig. 2. Figures 5(c) and 5(d) are the CCD image of the inference pattern and SEM of holographic fabricated structures in DPHPA. The agreement between the experimental pattern and the simulated one is very good. It further approves the method for the assignment of phases in the diffracted beams.

By comparison, computer generated holograms in SLM have shown powerful capability of generating an interference pattern from multi-beams up to 23 [17

17. G. Zito, B. Piccirillo, E. Santamato, A. Marino, V. Tkachenko, and G. Abbate, “Two-dimensional photonic quasicrystals by single beam computer-generated holography,” Opt. Express 16(8), 5164–5170 (2008). [CrossRef] [PubMed]

], and non-diffracting beams with same kz component [19

19. V. Arrizón, D. S. de-la-Llave, G. Méndez, and U. Ruiz, “Efficient generation of periodic and quasi-periodic non-diffractive optical fields with phase holograms,” Opt. Express 19(11), 10553–10562 (2011). [CrossRef] [PubMed]

22

22. M. Kumar and J. Joseph, “Embedding a nondiffracting defect site in helical lattice wave-field by optical phase engineering,” Appl. Opt. 52(23), 5653–5658 (2013). [CrossRef] [PubMed]

]. However the presented method can be potentially used to set designed gray levels for certain triangles at specific locations for a spatially varying, pixelated phase mask. Such a phase mask can be potentially used for the fabrication of graded photonic crystals where the effective refractive index at a certain location is determined by the filling fraction in holographic structures [24

24. J. B. Pendry, D. Schurig, and D. R. Smith, “Controlling electromagnetic fields,” Science 312(5781), 1780–1782 (2006). [CrossRef] [PubMed]

27

27. K. Ohlinger, J. Lutkenhaus, H. Zhang, and Y. Lin, “Spatially addressable design of Luneburg lens through spatial light modulator based holographic lithography,” J. Appl. Phys. submitted.

,29

29. R. C. Rumpf and J. Pazos, “Synthesis of spatially variant lattices,” Opt. Express 20(14), 15263–15274 (2012). [CrossRef] [PubMed]

]. Figures 5(e), 5(f),and 5( g) show simulated four-beam interference patterns formed by beams 1, 3, 4 and 5 with phases assignments from the gray levels shown in Figs. 3(a1, b1, c1), respectively. The patterns were obtained by setting the iso-intensity surface to be a half of maximum intensity. If a negative photoresist is exposed to these interference patterns, the high intensity region becomes polymerized. The filling fractions of dielectric materials versus the whole volume are 0.123, 0.143, and 0.176 in the patterns of Figs. 5(e),5(f),and 5(g), respectively. The effective refractive index is 1.09, 1.11, and 1.13, respectively, assuming a refractive index of 1.6 for DPHPA. By spatially varying the filling fraction and consequently the effective refractive index, graded index devices can be fabricated [24

24. J. B. Pendry, D. Schurig, and D. R. Smith, “Controlling electromagnetic fields,” Science 312(5781), 1780–1782 (2006). [CrossRef] [PubMed]

27

27. K. Ohlinger, J. Lutkenhaus, H. Zhang, and Y. Lin, “Spatially addressable design of Luneburg lens through spatial light modulator based holographic lithography,” J. Appl. Phys. submitted.

,29

29. R. C. Rumpf and J. Pazos, “Synthesis of spatially variant lattices,” Opt. Express 20(14), 15263–15274 (2012). [CrossRef] [PubMed]

]. The accumulated knowledge in this paper will be used to investigate the potential design of a gradient phase mask.

6. Summary

In summary, we were able to understand and assign the phase for the diffracted beams from the phase pattern displayed in the spatial light modulator. The phases of the interfering beams can be tuned by the gray levels in the phase pattern and verified by the holographically fabricated structures. The presented method can be potentially used to set designed gray levels for certain triangles at specific locations for spatially varying phase mask.

Acknowledgments

This work is supported by research grants from the U.S. National Science Foundation under Grant Nos. DMR-0934157, CMMI-1109971, -1266251, and ECCS-1128099.

References and links

1.

S. John, “Strong localization of photons in certain disordered dielectric superlattices,” Phys. Rev. Lett. 58(23), 2486–2489 (1987). [CrossRef] [PubMed]

2.

E. Yablonovitch, “Inhibited spontaneous emission in Solid-State Physics and Electronics,” Phys. Rev. Lett. 58(20), 2059–2062 (1987). [CrossRef] [PubMed]

3.

K. P. Chen, P. R. Herman, and R. Tam, “Strong fiber Bragg grating fabrication by hybrid 157- and 248-nm laser exposure,” IEEE Photon. Technol. Lett. 14(2), 170–172 (2002). [CrossRef]

4.

S. Noda, M. Yokoyama, M. Imada, A. Chutinan, and M. Mochizuki, “Polarization mode control of two-dimensional photonic crystal laser by unit cell structure design,” Science 293(5532), 1123–1125 (2001). [CrossRef] [PubMed]

5.

Y. Liu, F. Qin, Z.-M. Meng, F. Zhou, Q.-H. Mao, and Z.-Y. Li, “All-optical logic gates based on two-dimensional low-refractive-index nonlinear photonic crystal slabs,” Opt. Express 19(3), 1945–1953 (2011). [CrossRef] [PubMed]

6.

A. Tandaechanurat, S. Ishida, D. Guimard, M. Nomura, S. Iwamoto, and Y. Arakawa, “Lasing oscillation in a three-dimensional photonic crystal nanocavity with a complete bandgap,” Nat. Photonics 5(2), 91–94 (2011). [CrossRef]

7.

K. M. Ho, C. T. Chan, C. M. Soukoulis, R. Biswas, and M. Sigalas, “Photonic band gaps in three dimensions: new layer-by-layer periodic structures,” Solid State Commun. 89(5), 413–416 (1994). [CrossRef]

8.

A. Blanco, E. Chomski, S. Grabtchak, M. Ibisate, S. John, S. W. Leonard, C. Lopez, F. Meseguer, H. Miguez, J. P. Mondia, G. A. Ozin, O. Toader, A. Geoffrey, O. Toader, and H. M. van Driel, “Large-scale synthesis of a silicon photonic crystal with a complete three-dimensional bandgap near 1.5 micrometres,” Nature 405(6785), 437–440 (2000). [CrossRef] [PubMed]

9.

M. Deubel, G. von Freymann, M. Wegener, S. Pereira, K. Busch, and C. M. Soukoulis, “Direct laser writing of three-dimensional photonic-crystal templates for telecommunications,” Nat. Mater. 3(7), 444–447 (2004). [CrossRef] [PubMed]

10.

M. Campbell, D. N. Sharp, M. T. Harrison, R. G. Denning, and A. J. Turberfield, “Fabrication of photonic crystals for the visible spectrum by holographic lithography,” Nature 404(6773), 53–56 (2000). [CrossRef] [PubMed]

11.

S. Yang, M. Megens, J. Aizenberg, P. Wiltzius, P. M. Chaikin, and W. B. Russel, “Creating periodic three-dimensional structures by multibeam interference of visible laser,” Chem. Mater. 14(7), 2831–2833 (2002). [CrossRef]

12.

I. Divliansky, T. S. Mayer, K. S. Holliday, and V. H. Crespi, “Fabrication of three-dimensional polymer photonic crystal structures using single diffraction element interference lithography,” Appl. Phys. Lett. 82(11), 1667–1669 (2003). [CrossRef]

13.

Y. Lin, P. R. Herman, and K. Darmawikarta, “Design and holographic fabrication of tetragonal and cubic photonic crystals with phase mask: toward the mass-production of three-dimensional photonic crystals,” Appl. Phys. Lett. 86(7), 071117 (2005). [CrossRef]

14.

K. Ohlinger, H. Zhang, Y. Lin, D. Xu, and K. P. Chen, “A tunable three layer phase mask for single laser exposure 3D photonic crystal generations: bandgap simulation and holographic fabrication,” Opt. Mater. Express 1(5), 1034–1039 (2011). [CrossRef]

15.

D. Xu, K. P. Chen, A. Harb, D. Rodriguez, K. Lozano, and Y. Lin, “Phase tunable holographic fabrication for three-dimensional photonic crystal templates by using a single optical element,” Appl. Phys. Lett. 94(23), 231116 (2009).

16.

T. Y. M. Chan, O. Toader, and S. John, “Photonic band-gap formation by optical-phase-mask lithography,” Phys. Rev. E Stat. Nonlin. Soft Matter Phys. 73(4), 046610 (2006). [CrossRef] [PubMed]

17.

G. Zito, B. Piccirillo, E. Santamato, A. Marino, V. Tkachenko, and G. Abbate, “Two-dimensional photonic quasicrystals by single beam computer-generated holography,” Opt. Express 16(8), 5164–5170 (2008). [CrossRef] [PubMed]

18.

J. Xavier, M. Boguslawski, P. Rose, J. Joseph, and C. Denz, “Reconfigurable optically induced quasicrystallographic three-dimensional complex nonlinear photonic lattice structures,” Adv. Mater. 22(3), 356–360 (2010). [CrossRef] [PubMed]

19.

V. Arrizón, D. S. de-la-Llave, G. Méndez, and U. Ruiz, “Efficient generation of periodic and quasi-periodic non-diffractive optical fields with phase holograms,” Opt. Express 19(11), 10553–10562 (2011). [CrossRef] [PubMed]

20.

J. Xavier, R. Dasgupta, S. Ahlawat, J. Joseph, and P. K. Gupta, “Three dimensional optical twisters-driven helically stacked multi-layered microrotors,” Appl. Phys. Lett. 100(12), 121101 (2012). [CrossRef]

21.

J. Xavier and J. Joseph, “Tunable complex photonic chiral lattices by reconfigurable optical phase engineering,” Opt. Lett. 36(3), 403–405 (2011). [CrossRef] [PubMed]

22.

M. Kumar and J. Joseph, “Embedding a nondiffracting defect site in helical lattice wave-field by optical phase engineering,” Appl. Opt. 52(23), 5653–5658 (2013). [CrossRef] [PubMed]

23.

M. Boguslawski, A. Kelberer, P. Rose, and C. Denz, “Multiplexing complex two-dimensional photonic superlattices,” Opt. Express 20(24), 27331–27343 (2012). [CrossRef] [PubMed]

24.

J. B. Pendry, D. Schurig, and D. R. Smith, “Controlling electromagnetic fields,” Science 312(5781), 1780–1782 (2006). [CrossRef] [PubMed]

25.

U. Leonhardt, “Optical conformal mapping,” Science 312(5781), 1777–1780 (2006). [CrossRef] [PubMed]

26.

B. Arigong, K. Ohlinger, H. S. Kim, Y. Lin, and H. Zhang, “Transformation optics designed general optical luneburg lens with flattened shapes,” Proc. SPIE 8376, 83760R–1, 83760R-6 (2012). [CrossRef]

27.

K. Ohlinger, J. Lutkenhaus, H. Zhang, and Y. Lin, “Spatially addressable design of Luneburg lens through spatial light modulator based holographic lithography,” J. Appl. Phys. submitted.

28.

J. Lutkenhaus, D. George, D. Garrett, K. Ohlinger, H. Zhang, and Y. Lin, “Holographic formation of compound photonic crystal and nano-antenna templates through laser interference,” J. Appl. Phys. 113(10), 103103 (2013). [CrossRef]

29.

R. C. Rumpf and J. Pazos, “Synthesis of spatially variant lattices,” Opt. Express 20(14), 15263–15274 (2012). [CrossRef] [PubMed]

OCIS Codes
(090.1970) Holography : Diffractive optics
(220.3740) Optical design and fabrication : Lithography
(220.4000) Optical design and fabrication : Microstructure fabrication
(260.1960) Physical optics : Diffraction theory
(160.5298) Materials : Photonic crystals

ToC Category:
Holography

History
Original Manuscript: August 5, 2013
Revised Manuscript: September 18, 2013
Manuscript Accepted: October 8, 2013
Published: October 25, 2013

Citation
J. Lutkenhaus, D. George, M. Moazzezi, U. Philipose, and Y. Lin, "Digitally tunable holographic lithography using a spatial light modulator as a programmable phase mask," Opt. Express 21, 26227-26235 (2013)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-21-22-26227


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. S. John, “Strong localization of photons in certain disordered dielectric superlattices,” Phys. Rev. Lett.58(23), 2486–2489 (1987). [CrossRef] [PubMed]
  2. E. Yablonovitch, “Inhibited spontaneous emission in Solid-State Physics and Electronics,” Phys. Rev. Lett.58(20), 2059–2062 (1987). [CrossRef] [PubMed]
  3. K. P. Chen, P. R. Herman, and R. Tam, “Strong fiber Bragg grating fabrication by hybrid 157- and 248-nm laser exposure,” IEEE Photon. Technol. Lett.14(2), 170–172 (2002). [CrossRef]
  4. S. Noda, M. Yokoyama, M. Imada, A. Chutinan, and M. Mochizuki, “Polarization mode control of two-dimensional photonic crystal laser by unit cell structure design,” Science293(5532), 1123–1125 (2001). [CrossRef] [PubMed]
  5. Y. Liu, F. Qin, Z.-M. Meng, F. Zhou, Q.-H. Mao, and Z.-Y. Li, “All-optical logic gates based on two-dimensional low-refractive-index nonlinear photonic crystal slabs,” Opt. Express19(3), 1945–1953 (2011). [CrossRef] [PubMed]
  6. A. Tandaechanurat, S. Ishida, D. Guimard, M. Nomura, S. Iwamoto, and Y. Arakawa, “Lasing oscillation in a three-dimensional photonic crystal nanocavity with a complete bandgap,” Nat. Photonics5(2), 91–94 (2011). [CrossRef]
  7. K. M. Ho, C. T. Chan, C. M. Soukoulis, R. Biswas, and M. Sigalas, “Photonic band gaps in three dimensions: new layer-by-layer periodic structures,” Solid State Commun.89(5), 413–416 (1994). [CrossRef]
  8. A. Blanco, E. Chomski, S. Grabtchak, M. Ibisate, S. John, S. W. Leonard, C. Lopez, F. Meseguer, H. Miguez, J. P. Mondia, G. A. Ozin, O. Toader, A. Geoffrey, O. Toader, and H. M. van Driel, “Large-scale synthesis of a silicon photonic crystal with a complete three-dimensional bandgap near 1.5 micrometres,” Nature405(6785), 437–440 (2000). [CrossRef] [PubMed]
  9. M. Deubel, G. von Freymann, M. Wegener, S. Pereira, K. Busch, and C. M. Soukoulis, “Direct laser writing of three-dimensional photonic-crystal templates for telecommunications,” Nat. Mater.3(7), 444–447 (2004). [CrossRef] [PubMed]
  10. M. Campbell, D. N. Sharp, M. T. Harrison, R. G. Denning, and A. J. Turberfield, “Fabrication of photonic crystals for the visible spectrum by holographic lithography,” Nature404(6773), 53–56 (2000). [CrossRef] [PubMed]
  11. S. Yang, M. Megens, J. Aizenberg, P. Wiltzius, P. M. Chaikin, and W. B. Russel, “Creating periodic three-dimensional structures by multibeam interference of visible laser,” Chem. Mater.14(7), 2831–2833 (2002). [CrossRef]
  12. I. Divliansky, T. S. Mayer, K. S. Holliday, and V. H. Crespi, “Fabrication of three-dimensional polymer photonic crystal structures using single diffraction element interference lithography,” Appl. Phys. Lett.82(11), 1667–1669 (2003). [CrossRef]
  13. Y. Lin, P. R. Herman, and K. Darmawikarta, “Design and holographic fabrication of tetragonal and cubic photonic crystals with phase mask: toward the mass-production of three-dimensional photonic crystals,” Appl. Phys. Lett.86(7), 071117 (2005). [CrossRef]
  14. K. Ohlinger, H. Zhang, Y. Lin, D. Xu, and K. P. Chen, “A tunable three layer phase mask for single laser exposure 3D photonic crystal generations: bandgap simulation and holographic fabrication,” Opt. Mater. Express1(5), 1034–1039 (2011). [CrossRef]
  15. D. Xu, K. P. Chen, A. Harb, D. Rodriguez, K. Lozano, and Y. Lin, “Phase tunable holographic fabrication for three-dimensional photonic crystal templates by using a single optical element,” Appl. Phys. Lett.94(23), 231116 (2009).
  16. T. Y. M. Chan, O. Toader, and S. John, “Photonic band-gap formation by optical-phase-mask lithography,” Phys. Rev. E Stat. Nonlin. Soft Matter Phys.73(4), 046610 (2006). [CrossRef] [PubMed]
  17. G. Zito, B. Piccirillo, E. Santamato, A. Marino, V. Tkachenko, and G. Abbate, “Two-dimensional photonic quasicrystals by single beam computer-generated holography,” Opt. Express16(8), 5164–5170 (2008). [CrossRef] [PubMed]
  18. J. Xavier, M. Boguslawski, P. Rose, J. Joseph, and C. Denz, “Reconfigurable optically induced quasicrystallographic three-dimensional complex nonlinear photonic lattice structures,” Adv. Mater.22(3), 356–360 (2010). [CrossRef] [PubMed]
  19. V. Arrizón, D. S. de-la-Llave, G. Méndez, and U. Ruiz, “Efficient generation of periodic and quasi-periodic non-diffractive optical fields with phase holograms,” Opt. Express19(11), 10553–10562 (2011). [CrossRef] [PubMed]
  20. J. Xavier, R. Dasgupta, S. Ahlawat, J. Joseph, and P. K. Gupta, “Three dimensional optical twisters-driven helically stacked multi-layered microrotors,” Appl. Phys. Lett.100(12), 121101 (2012). [CrossRef]
  21. J. Xavier and J. Joseph, “Tunable complex photonic chiral lattices by reconfigurable optical phase engineering,” Opt. Lett.36(3), 403–405 (2011). [CrossRef] [PubMed]
  22. M. Kumar and J. Joseph, “Embedding a nondiffracting defect site in helical lattice wave-field by optical phase engineering,” Appl. Opt.52(23), 5653–5658 (2013). [CrossRef] [PubMed]
  23. M. Boguslawski, A. Kelberer, P. Rose, and C. Denz, “Multiplexing complex two-dimensional photonic superlattices,” Opt. Express20(24), 27331–27343 (2012). [CrossRef] [PubMed]
  24. J. B. Pendry, D. Schurig, and D. R. Smith, “Controlling electromagnetic fields,” Science312(5781), 1780–1782 (2006). [CrossRef] [PubMed]
  25. U. Leonhardt, “Optical conformal mapping,” Science312(5781), 1777–1780 (2006). [CrossRef] [PubMed]
  26. B. Arigong, K. Ohlinger, H. S. Kim, Y. Lin, and H. Zhang, “Transformation optics designed general optical luneburg lens with flattened shapes,” Proc. SPIE8376, 83760R–1, 83760R-6 (2012). [CrossRef]
  27. K. Ohlinger, J. Lutkenhaus, H. Zhang, and Y. Lin, “Spatially addressable design of Luneburg lens through spatial light modulator based holographic lithography,” J. Appl. Phys.submitted.
  28. J. Lutkenhaus, D. George, D. Garrett, K. Ohlinger, H. Zhang, and Y. Lin, “Holographic formation of compound photonic crystal and nano-antenna templates through laser interference,” J. Appl. Phys.113(10), 103103 (2013). [CrossRef]
  29. R. C. Rumpf and J. Pazos, “Synthesis of spatially variant lattices,” Opt. Express20(14), 15263–15274 (2012). [CrossRef] [PubMed]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1 Fig. 2 Fig. 3
 
Fig. 4 Fig. 5
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited