OSA's Digital Library

Optics Express

Optics Express

  • Editor: Andrew M. Weiner
  • Vol. 21, Iss. 24 — Dec. 2, 2013
  • pp: 29808–29817
« Show journal navigation

Low-loss sharp bends in polymer waveguides enabled by the introduction of a thin metal layer

Mustafa Akin Sefunc, Markus Pollnau, and Sonia M. García-Blanco  »View Author Affiliations


Optics Express, Vol. 21, Issue 24, pp. 29808-29817 (2013)
http://dx.doi.org/10.1364/OE.21.029808


View Full Text Article

Acrobat PDF (1131 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

Embodying a thin metallic layer underneath the core of a sharply bent polymer waveguide is shown in this work to considerably reduce the total losses of both the quasi-transverse-electric and quasi-transverse-magnetic modes. The computational results show a total loss as low as ~0.02 dB/90° for the quasi-transverse-electric mode for radii between 6 and 13 µm at the wavelength of 1.55 µm, which corresponds to a 10-fold improvement over the purely dielectric counterpart. The radii range exhibiting such low total loss can be tuned by properly selecting the parameters of the structure. For the quasi-transverse-magnetic mode, the metal layer reduces the total losses modestly for radii ranging from 3 to 10 µm. Simulation results for different structural parameters are presented.

© 2013 Optical Society of America

1. Introduction

Integrated optical devices in polymeric materials have been the subject of a great deal of research over the past couple of decades [1

1. L. Eldada and L. W. Shacklette, “Advances in polymer integrated optics,” IEEE J. Sel. Top. Quantum Electron. 6, 54–68 (2000).

4

4. L. Jin, J. Wang, X. Fu, B. Yang, Y. Shi, and D. Dai, “High-Q microring resonators with 2 × 2 angled multimode interference couplers,” IEEE Photon. Technol. Lett. 25(6), 612–614 (2013). [CrossRef]

]. Advantages of polymer waveguides include low cost as well as flexibility and ease of fabrication. Polymer materials span a wide range of refractive index values and exhibit a large transparency window, which makes them compatible with many photonic technologies for a large range of applications. Furthermore, different active dopants can be added to the polymeric material to fabricate devices with electro-optical [5

5. Y. Shi, C. Zhang, H. Zhang, J. H. Bechtel, L. R. Dalton, B. H. Robinson, and W. H. Steier, “Low (sub-1-Volt) halfwave voltage polymeric electro-optic modulators achieved by controlling chromophore shape,” Science 288(5463), 119–122 (2000). [CrossRef] [PubMed]

], optical gain [6

6. Y. Yang, M. B. J. Diemeer, C. Grivas, G. Sengo, A. Driessen, and M. Pollnau, “Steady-state lasing in a solid polymer,” Laser Phys. Lett. 7(9), 650–656 (2010). [CrossRef]

], or detection [7

7. X. Gong, M. Tong, Y. Xia, W. Cai, J. S. Moon, Y. Cao, G. Yu, C. L. Shieh, B. Nilsson, and A. J. Heeger, “High-detectivity polymer photodetectors with spectral response from 300 nm to 1450 nm,” Science 325(5948), 1665–1667 (2009). [CrossRef] [PubMed]

] capabilities.

One of the main drawbacks of polymeric waveguides is the large radius of curvature, typically a few tens of micrometers [3

3. B. Yang, L. Yang, R. Hu, Z. Sheng, D. Dai, Q. Liu, and S. He, “Fabrication and characterization of small optical ridge waveguides based on SU-8 polymer,” J. Lightwave Technol. 27(18), 4091–4096 (2009). [CrossRef]

, 4

4. L. Jin, J. Wang, X. Fu, B. Yang, Y. Shi, and D. Dai, “High-Q microring resonators with 2 × 2 angled multimode interference couplers,” IEEE Photon. Technol. Lett. 25(6), 612–614 (2013). [CrossRef]

], required for low-loss propagation. This is due to the low refractive index contrast between core and cladding typically obtained in polymer waveguide structures. Smaller radii of curvature are highly desirable in integrated photonics as they permit decreasing device footprint. In devices such as ring resonators, a small radius not only decreases dimensions but can also potentially reduce power consumption in active devices, while providing a large free spectral range (FSR). The latter is an important parameter in the design of filters and modulators for WDM systems [8

8. Q. Xu, D. Fattal, and R. G. Beausoleil, “Silicon microring resonators with 1.5-μm radius,” Opt. Express 16, 4310–4315 (2008).

] as well as tunable lasers with a wide wavelength range and stable laser operation [9

9. Y. Deki, T. Hatanaka, M. Takahashi, T. Takeuchi, S. Watanabe, S. Takaesu, T. Miyazaki, M. Horie, and H. Yamazaki, “Wide-wavelength tunable lasers with 100 GHz FSR ring resonators,” Electron. Lett. 43(4), 225–226 (2007). [CrossRef]

] in which a single resonance peak within the material gain bandwidth prevents mode hopping while permitting smooth wavelength tuning.

Plasmonic waveguides have been proposed as good candidates for very-high-scale integration of photonic devices thanks to their capability to achieve very tight light confinement, which permits increasing device density, while benefiting from the large bandwidth of photonic devices [10

10. S. I. Bozhevolnyi, V. S. Volkov, E. Devaux, J. Y. Laluet, and T. W. Ebbesen, “Channel plasmon subwavelength waveguide components including interferometers and ring resonators,” Nature 440(7083), 508–511 (2006). [CrossRef] [PubMed]

]. A trade-off between confinement and propagation losses, however, has until now limited the application of this type of waveguides in real-life devices. In an attempt to decrease propagation losses while maintaining sub-wavelength confinement, different waveguide structures have been proposed such as dielectric-loaded surface plasmon waveguides [11

11. T. Holmgaard and S. I. Bozhevolnyi, “Theoretical analysis of dielectric-loaded surface plasmon-polariton waveguides,” Phys. Rev. B 75(24), 245405 (2007). [CrossRef]

, 12

12. T. Holmgaard, Z. Chen, S. I. Bozhevolnyi, L. Markey, and A. Dereux, “Dielectric-loaded plasmonic waveguide-ring resonators,” Opt. Express 17(4), 2968–2975 (2009). [CrossRef] [PubMed]

], long-range dielectric-loaded surface plasmon waveguides [13

13. T. Holmgaard, J. Gosciniak, and S. I. Bozhevolnyi, “Long-range dielectric-loaded surface plasmon-polariton waveguides,” Opt. Express 18(22), 23009–23015 (2010). [CrossRef] [PubMed]

] and hybrid plasmonic waveguides [14

14. M. Z. Alam, J. Meier, J. S. Aitchison, and M. Mojahedi, “Super mode propagation in low index medium,” in Conference on Lasers and Electro-Optics/Quantum Electronics and Laser Science Conference and Photonic Applications Systems Technologies, OSA Technical Digest Series (CD) (Optical Society of America, 2007), paper JThD112.

16

16. R. F. Oulton, V. J. Sorger, D. A. Genov, D. F. P. Pile, and X. Zhang, “A hybrid plasmonic waveguide for subwavelength confinement and long-range propagation,” Nat. Photonics 2(8), 496–500 (2008). [CrossRef]

]. The high electromagnetic field confinement in plasmonic structures permits the realization of bends with radii of only a few micrometers. Bends in channel grooved plasmonic waveguides [10

10. S. I. Bozhevolnyi, V. S. Volkov, E. Devaux, J. Y. Laluet, and T. W. Ebbesen, “Channel plasmon subwavelength waveguide components including interferometers and ring resonators,” Nature 440(7083), 508–511 (2006). [CrossRef] [PubMed]

], metallic nanowire waveguides [17

17. D. J. Dikken, M. Spasenović, E. Verhagen, D. van Oosten, and L. K. Kuipers, “Characterization of bending losses for curved plasmonic nanowire waveguides,” Opt. Express 18(15), 16112–16119 (2010). [CrossRef] [PubMed]

19

19. A. V. Krasavin and A. V. Zayats, “Guiding light at the nanoscale: numerical optimization of ultrasubwavelength metallic wire plasmonic waveguides,” Opt. Lett. 36(16), 3127–3129 (2011). [CrossRef] [PubMed]

], metal-dielectric-metal plasmonic waveguides [20

20. D. F. P. Pile and D. K. Gramotnev, “Plasmonic subwavelength waveguides: next to zero losses at sharp bends,” Opt. Lett. 30(10), 1186–1188 (2005). [CrossRef] [PubMed]

], dielectric-loaded surface plasmon waveguides [11

11. T. Holmgaard and S. I. Bozhevolnyi, “Theoretical analysis of dielectric-loaded surface plasmon-polariton waveguides,” Phys. Rev. B 75(24), 245405 (2007). [CrossRef]

, 12

12. T. Holmgaard, Z. Chen, S. I. Bozhevolnyi, L. Markey, and A. Dereux, “Dielectric-loaded plasmonic waveguide-ring resonators,” Opt. Express 17(4), 2968–2975 (2009). [CrossRef] [PubMed]

, 21

21. C. Yang, E. J. Teo, T. Goh, S. L. Teo, J. H. Teng, and A. A. Bettiol, “Metal-assisted photonic mode for ultrasmall bending with long propagation length at visible wavelengths,” Opt. Express 20(21), 23898–23905 (2012). [CrossRef] [PubMed]

23

23. T. Holmgaard, Z. Chen, S. I. Bozhevolnyi, L. Markey, A. Dereux, A. V. Krasavin, and A. V. Zayats, “Bend- and splitting loss of dielectric-loaded surface plasmon-polariton waveguides,” Opt. Express 16(18), 13585–13592 (2008). [CrossRef] [PubMed]

], metal-clad waveguides [24

24. M. W. Kim and P. C. Ku, “Lasing in a metal-clad microring resonator,” Appl. Phys. Lett. 98(13), 131107 (2011). [CrossRef]

] and hybrid dielectric-loaded surface plasmon waveguides [25

25. H. S. Chu, Y. Akimov, P. Bai, and E. P. Li, “Submicrometer radius and highly confined plasmonic ring resonator filters based on hybrid metal-oxide-semiconductor waveguide,” Opt. Lett. 37(21), 4564–4566 (2012). [CrossRef] [PubMed]

, 26

26. C. Horvath, D. Bachman, M. Wu, D. Perron, and V. Van, “Polymer hybrid plasmonic waveguide and microring resonators,” IEEE Photon. Technol. Lett. 23(17), 1267–1269 (2011). [CrossRef]

] have been investigated with radii of a few micrometers. However, the reported total losses per 90 degree bend are still too high for practical applications. The limiting factor is typically the high propagation loss of the plasmonic waveguide structures. Krasavin et al. [19

19. A. V. Krasavin and A. V. Zayats, “Guiding light at the nanoscale: numerical optimization of ultrasubwavelength metallic wire plasmonic waveguides,” Opt. Lett. 36(16), 3127–3129 (2011). [CrossRef] [PubMed]

] proposed the use of optical gain to compensate bend losses, thereby increasing the transmission through the bend to more than 95% (~0.2 dB of signal loss) in dielectric-loaded surface plasmon waveguides. Dai et al. [27

27. D. Dai, Y. Shi, S. He, L. Wosinski, and L. Thylen, “Silicon hybrid plasmonic submicron-donut resonator with pure dielectric access waveguides,” Opt. Express 19(24), 23671–23682 (2011). [CrossRef] [PubMed]

] proposed a silicon hybrid plasmonic waveguide design capable of very sharp bends with low losses per 90 degree bend. Total losses close to ~0.04 dB/90° were calculated for a bend radius of 1.2 µm for the transverse-magnetic (TM) fundamental mode.

In this work, the introduction of a thin metallic layer underneath the core of a polymer waveguide is shown to reduce the calculated total losses (dB/90°) of sharp bends with respect to the total losses of the equivalent dielectric structure (i.e., without the metallic layer) for a large range of bend radii. The loss reduction is especially significant for the quasi-transverse-electric (TE) mode, for which the metallic configuration exhibits lower total losses for radii below 35 µm. For the quasi-TE mode, losses as low as ~0.02 dB/90° have been calculated for a wide range of radii that can be tuned by properly selecting the parameters of the structure. Such decrease in total loss represents one order of magnitude reduction with respect to the total losses of the pure dielectric structure for the same radii range. In the case of the quasi-TM mode, the total losses of the metallic structure are smaller than those of the dielectric structure for radii ranging from 3 to 10 µm. Introduction of the thin metallic layer in the proposed structure reduces the optimum radius of curvature of polymer waveguides from tens of micrometers to less than 10 µm, thereby enabling the utilization of polymer waveguides in highly integrated optical circuits and in devices where very sharp bends are necessary, such as ring resonators with large FSR. In the following sections, a detailed study of the total losses of the proposed polymer dielectric-loaded hybrid metallic bent waveguides including the effect of different structural parameters and materials on the calculated total losses is presented.

2. Proposed structure

The schematic configurations of the waveguide geometries studied in this paper are shown in Fig. 1
Fig. 1 (a) Dielectric-loaded hybrid plasmonic waveguide (“metallic” structure) and (b) dielectric reference structure (“non-metallic” structure). Typical parameters: hridge = wridge = 2 µm, tbuffer = 100 nm, tmetal = 100 nm. The silicon substrate was not taken into account in the simulations, as the thickness of the SiO2 undercladding was considered sufficiently thick for the mode not to be influenced by the presence of the silicon substrate.
. The proposed structure corresponds to a dielectric-loaded hybrid plasmonic waveguide consisting of a polymer ridge separated from the metal underneath by a thin low refractive index dielectric layer. The material selected for the ridge is the negative tone epoxy resist SU-8 [28

28. K. Y. Lee, N. LaBianca, S. A. Rishton, S. Zolgharnain, J. D. Gelorme, J. Shaw, and T. H.-P. Chang, “Micromachining applications of a high resolution ultrathick photoresist,” J. Vac. Sci. Technol. B 13(6), 3012–3016 (1995). [CrossRef]

], although similar results apply to a wide range of architectures exhibiting low refractive index contrast between substrate and core. For high-index-contrast waveguide architectures introduction of the metal has a less beneficial effect on the propagation losses. The material of the thin buffer layer is SiO2. Gold was selected for the metallic layer. The substrate consists of silicon with a sufficiently thick layer of thermal SiO2. Figure 1(b) shows the cross-section of the entirely dielectric structure used as a benchmark. The dielectric-loaded hybrid plasmonic waveguide [Fig. 1(a)] will be referred to as “metallic” in the subsequent sections, whereas the dielectric polymer waveguide [Fig. 1(b)] will be called “non-metallic”. The effect of the thickness of the different layers, the dimensions of the ridge and the type of metal selected will be studied in the following sections. The corresponding optical properties of the different materials at the wavelength of interest (λ = 1.55 µm) as well as the ranges of parameters considered in this study are summarized in Table 1

Table 1. Refractive indices and thicknesses of the materials employed (λ = 1.55 µm).

table-icon
View This Table
| View All Tables
.

The distance between the center of curvature and the outer rim of the waveguide defines the bend radius, R, as depicted in Fig. 1. This definition of bend radius was chosen, because the outer rim is the important interface in very sharply bent waveguides, since the mode is pushed towards this boundary. Since disk resonators are devices which do not possess a waveguide width, defining the radius according to the outer interface will ensure compatibility of all the results.

3. Modeling of bent waveguides

4. Study of bend losses as a function of radius for different parameters of the structure

In this comparative study, several structural parameters are taken into account to gain insight into their influence on the total losses of the bend. Such parameters comprise the ridge width (wridge) and height (hridge), buffer layer thickness (tbuffer), metal layer thickness (tmetal), and type of metal. The ridge width and height are each set to 2 µm to ensure single-mode operation (i.e., only one quasi-TE and one quasi-TM mode are supported by the structure).

Figure 2 depicts the real part of the dominant E-field component for the quasi-TE and quasi-TM modes supported by the non-metallic [Figs. 2(a) and 2(b)] and metallic [Figs. 2(c) and 2(d)] waveguide structures. It can be seen that the guided mode binds to the outer (right-hand side) rim of the ridge, since the turning is in the direction of the negative x-axis. The radius of curvature used in Fig. 2 is 6 µm. In the non-metallic structure, the generated leaky waves can be clearly observed and are due to the sharp bending of the waveguide. As the radius of curvature is further decreased, leakage into the substrate increases with the consequent reduction in mode intensity. This behavior translates into an augmentation of the bend losses for decreased radii of curvature, as can be seen in Fig. 3
Fig. 3 Total loss (dB/90°) versus bend radius (R) for metallic and non-metallic structures for (a) quasi-TE and (b) quasi-TM modes with the parameters of wridge = 2 µm, hridge = 2 µm, tbuffer = 100 nm, and tmetal = 100 nm (only for metallic structure). The insets are a zoom of the corresponding loss plots in the region of interest.
(blue circles).

Introduction of a thin metallic layer underneath the polymer ridge blocks the radiation modes and pushes the quasi-TE mode towards the ridge in the positive y-axis direction [Fig. 2(c)]. Figure 3(a) shows the total losses per 90 degree bend for the metallic quasi-TE mode in comparison with those of the quasi-TE mode of the non-metallic structure. For large radii of curvature, the total losses per 90 degree bend of the metallic structure rise linearly with increasing radius. In this radius range, the total losses are dominated by the propagation losses and thus, they augment as the length of the 90 degree waveguide segment increases. When the radius decreases below a critical radius, the total losses rise again, this time due to the radiative losses introduced by the bend. It can be clearly seen in Fig. 3(a) that the introduction of the thin metal layer shifts the critical radius to a much lower value (i.e., ~7 µm) than in the non-metallic waveguide. Below a radius of ~35 µm, the total losses per 90 degree bend of the metallic structure are smaller than the ones of the non-metallic structure. This is particularly interesting for radii between 6 and 13 µm, where losses as low as 0.02 dB/90° have been calculated [inset of Fig. 3(a)].

The thin metallic layer underneath the polymer ridge transforms the photonic quasi-TM mode of the non-metallic structure [Fig. 2(b)] into a hybrid plasmonic-photonic mode. Such a mode is strongly coupled to the metal, thereby reducing leakage to the substrate and, therefore, the bend losses for small radii of curvature [Fig. 2(d)]. However, since the metal is highly absorptive at the wavelength of interest, high propagation losses are expected. High propagation losses are dominant for increasing radii [Fig. 3(b)]. A shift of the critical radius, below which the bend losses become dominant, to a smaller value than in the non-metallic structure still occurs despite the large propagation losses. For a narrow range of bend radii from 3 µm to 10 µm, the metallic structure exhibits lower total losses compared to the non-metallic counterpart [inset of Fig. 3(b)].

It is important to mention that the reduction of total bend losses (dB/90 degree bend) by the introduction of thin metal layers is larger for low refractive index contrast waveguides, for which the positive influence of usage of thin metal layers, i.e., by preventing the leakage, is higher than the negative effect of increased absorption introduced by the metal. High index contrast waveguide architectures show better confinement and less leakage to the substrate. For such structures, a thin metal layer has a lesser effect on blocking the radiation modes and pushing the guided mode towards the ridge, while the absorption of light due to the presence of the metal becomes significant.

The transition loss between a non-metallic straight waveguide and a metallic bend section have been investigated for the proposed waveguide architectures. The optimum offset values which provide maximum coupling efficiency have been calculated. Transition losses and optimum offset values depend on the particular waveguide parameters, the radius of curvature as well as the polarization. Typical transition losses are in the range of 0.8 dB to 1.5 dB per straight to bend connection. The transition losses are in the range of 0.1 dB to 1.3 dB for a non-metallic straight to a non-metallic bend waveguide section. The approach considered in this paper can also be applied to ring resonators in which no straight to bend connection is required.

4.1 Dependence of total losses on thickness of the buffer layer

The influence of the buffer layer thickness on the total losses has been investigated. The thickness of the buffer layer was varied between 0 nm and 400 nm. The losses per 90 degree bend for radii ranging from 2 µm to 30 µm were calculated for each value of buffer layer thickness. Results for the quasi-TE and quasi-TM modes are displayed in Fig. 4
Fig. 4 Effect of the SiO2 buffer thickness: Total losses (dB/90°) versus bend radius (R) for the metallic structure with the parameters of wridge = 2 µm, hridge = 2 µm, tmetal = 100 nm for different tbuffer parameter (tbuffer = 0 nm, 25 nm, 50 nm, 100 nm, 200 nm, and 400 nm) for (a) quasi-TE and (b) quasi-TM modes. The insets zoom in the regions of interest.
. As the thickness of the buffer layer augments, the critical radius for minimum losses per 90 degree bend shifts to larger radii. Increasing the buffer layer thickness has two consequences. For large bend radii, the losses per 90 degree go down as the thickness of the buffer layer augments. The field distribution is further away from the metal layer, therefore inducing less propagation losses for both quasi-TE and quasi-TM modes. For smaller radii (i.e., below the critical radius), as the buffer layer thickness increases, higher bend losses are obtained. Simultaneously, the critical radius shifts towards larger radii. In the case of the quasi-TE modes, this behavior can be explained as a reduction of the shield effect of the metal due to its larger distance from the mode [Fig. 5(c)
Fig. 5 Effect of the buffer layer thickness: Calculated 2-D mode profiles (shown as the real part of the dominant electrical field component) at λ = 1.55 µm, R = 6 µm for the metallic structure with the parameters of wridge = 2 µm, hridge = 2 µm, tmetal = 100 nm, tbuffer = 0 nm for the (a) quasi-TE (Media 3), (b) quasi-TM (Media 4) modes and in the case of tbuffer = 400 nm for (c) quasi-TE (Media 3) and (d) quasi-TM modes (Media 4).
]. For the quasi-TM modes, a thicker buffer layer enhances coupling of the bend mode to a surface plasmon mode supported by the layer structure outside the polymer ridge [Fig. 5(d)]. Figures 5(a) and 5(b) shows the mode profiles for quasi-TE and quasi-TM modes for a structure with no buffer layer.

The thickness of the buffer layer is, therefore, a very important design parameter that permits shifting the range of radii where the lowest total losses occur. For example, no buffer layer would be preferred if the application requires the smallest radius possible. A thicker buffer layer would be preferred if low losses for slightly larger radii are desired. A 400 nm thick buffer layer enlarges the range of radii that exhibit total losses around ~0.02 dB/90° to between 13 and 25 µm for the parameters of the structure detailed in Fig. 4.

4.2 Dependence of bend losses on metal layer thickness

The effect of the metal layer thickness was investigated. Figure 6
Fig. 6 Effect of metal thickness: Total loss (dB/90°) versus bend radius (R) for the metallic structure with the structural parameters of wridge = 2 µm, hridge = 2 µm, tbuffer = 100 nm for different tmetal (tmetal = 25 nm, 50 nm, 100 nm, 150 nm and 200 nm) for (a) quasi-TE and (b) quasi-TM modes. The insets are zoom of the corresponding loss plots.
shows the total loss per 90 degree bend as a function of bend radius for both the quasi-TE [Fig. 6(a)] and the quasi-TM [Fig. 6(b)] modes. For the quasi-TE mode [Fig. 6(a)], provided the metal layer is sufficiently thick, it acts as a shield pushing the mode towards the ridge and preventing it from radiating to leaky waves in the substrate. This is the case for thicknesses above 50 nm. For thicknesses of the gold layer comparable to, or smaller than the penetration of the field in the metal layer, coupling of the field to the substrate radiation modes can still occur, thereby increasing the contribution of the bend losses to the total loss per 90 degrees bend.

In the case of quasi-TM modes [Fig. 6(b)], as the metal thickness decreases, the mode binds more to the metal via excitation of surface plasmon modes on both surfaces of the metal layer. As a consequence, the propagation losses dramatically increase, as can be seen for gold layers thinner than 100 nm [Fig. 6(b)].

4.3 Analysis of total loss dependence on metal type

In the case of quasi-TM modes, the more negative the real part of the dielectric permittivity is, the lower are the propagation losses. This is in agreement with the results of the simulations, shown in Fig. 7(b).

5. Conclusions

In this work, we proposed and demonstrated numerically that introducing a thin metal layer underneath the core of a polymer waveguide permits the realization of sharp bends with calculated total losses (dB/90°) smaller than those of the equivalent dielectric waveguide without the metallic layer, both for quasi-TE and quasi-TM modes. The FD mode calculations indicate more than a 10-fold reduction of the bend losses with respect to the entirely dielectric structure for radii below ~35 µm for quasi-TE modes, for which total losses as low as 0.02 dB/90° have been calculated for a wide range of radii, which can be tuned by properly selecting the thickness of the buffer layer. A more modest decrease of the total losses has been obtained for the quasi-TM modes for radii between 3 and 10 µm. By choosing the right structural parameters, the introduction of the thin metallic layer permits to decrease the optimum bend radius from ~70 µm (i.e., in the entirely dielectric structure) to less than 10 µm while maintaining the total bend loss performance at ~0.02 dB/90°.

In TE polarization, the reduction of the total bend losses can be attributed to the shielding of the mode by the metal layer, which prevents it from leaking into the substrate. The mechanism for the reduction of bend losses is different in TM polarization, for which the higher confinement of the hybrid plasmonic-photonic mode to the metal layer permits decreasing the radius of curvature before coupling to radiation modes occurs.

The approach considered in this paper is quite promising, as it allows the use of polymer waveguides in large-scale photonic integration where sharply bent waveguides with radii of a few micrometers are essential to shrink the footprint of photonic circuitry.

Acknowledgments

The authors acknowledge support from the FP7 Marie Curie Career Integration Grant PCIG09-GA-2011-29389 and the University of Twente Aspasia fund. M. Hammer, H. J. W. M. Hoekstra, R. Stoffer, D. J. Dikken and J. Herek are thanked for useful discussions and advice.

References and links

1.

L. Eldada and L. W. Shacklette, “Advances in polymer integrated optics,” IEEE J. Sel. Top. Quantum Electron. 6, 54–68 (2000).

2.

H. Ma, A. K. Y. Jen, and L. R. Dalton, “Polymer-based optical waveguides: materials, processing and devices,” Adv. Mater. 14(19), 1339–1365 (2002). [CrossRef]

3.

B. Yang, L. Yang, R. Hu, Z. Sheng, D. Dai, Q. Liu, and S. He, “Fabrication and characterization of small optical ridge waveguides based on SU-8 polymer,” J. Lightwave Technol. 27(18), 4091–4096 (2009). [CrossRef]

4.

L. Jin, J. Wang, X. Fu, B. Yang, Y. Shi, and D. Dai, “High-Q microring resonators with 2 × 2 angled multimode interference couplers,” IEEE Photon. Technol. Lett. 25(6), 612–614 (2013). [CrossRef]

5.

Y. Shi, C. Zhang, H. Zhang, J. H. Bechtel, L. R. Dalton, B. H. Robinson, and W. H. Steier, “Low (sub-1-Volt) halfwave voltage polymeric electro-optic modulators achieved by controlling chromophore shape,” Science 288(5463), 119–122 (2000). [CrossRef] [PubMed]

6.

Y. Yang, M. B. J. Diemeer, C. Grivas, G. Sengo, A. Driessen, and M. Pollnau, “Steady-state lasing in a solid polymer,” Laser Phys. Lett. 7(9), 650–656 (2010). [CrossRef]

7.

X. Gong, M. Tong, Y. Xia, W. Cai, J. S. Moon, Y. Cao, G. Yu, C. L. Shieh, B. Nilsson, and A. J. Heeger, “High-detectivity polymer photodetectors with spectral response from 300 nm to 1450 nm,” Science 325(5948), 1665–1667 (2009). [CrossRef] [PubMed]

8.

Q. Xu, D. Fattal, and R. G. Beausoleil, “Silicon microring resonators with 1.5-μm radius,” Opt. Express 16, 4310–4315 (2008).

9.

Y. Deki, T. Hatanaka, M. Takahashi, T. Takeuchi, S. Watanabe, S. Takaesu, T. Miyazaki, M. Horie, and H. Yamazaki, “Wide-wavelength tunable lasers with 100 GHz FSR ring resonators,” Electron. Lett. 43(4), 225–226 (2007). [CrossRef]

10.

S. I. Bozhevolnyi, V. S. Volkov, E. Devaux, J. Y. Laluet, and T. W. Ebbesen, “Channel plasmon subwavelength waveguide components including interferometers and ring resonators,” Nature 440(7083), 508–511 (2006). [CrossRef] [PubMed]

11.

T. Holmgaard and S. I. Bozhevolnyi, “Theoretical analysis of dielectric-loaded surface plasmon-polariton waveguides,” Phys. Rev. B 75(24), 245405 (2007). [CrossRef]

12.

T. Holmgaard, Z. Chen, S. I. Bozhevolnyi, L. Markey, and A. Dereux, “Dielectric-loaded plasmonic waveguide-ring resonators,” Opt. Express 17(4), 2968–2975 (2009). [CrossRef] [PubMed]

13.

T. Holmgaard, J. Gosciniak, and S. I. Bozhevolnyi, “Long-range dielectric-loaded surface plasmon-polariton waveguides,” Opt. Express 18(22), 23009–23015 (2010). [CrossRef] [PubMed]

14.

M. Z. Alam, J. Meier, J. S. Aitchison, and M. Mojahedi, “Super mode propagation in low index medium,” in Conference on Lasers and Electro-Optics/Quantum Electronics and Laser Science Conference and Photonic Applications Systems Technologies, OSA Technical Digest Series (CD) (Optical Society of America, 2007), paper JThD112.

15.

M. Z. Alam, J. Meier, J. S. Aitchison, and M. Mojahedi, “Propagation characteristics of hybrid modes supported by metal-low-high index waveguides and bends,” Opt. Express 18(12), 12971–12979 (2010). [CrossRef] [PubMed]

16.

R. F. Oulton, V. J. Sorger, D. A. Genov, D. F. P. Pile, and X. Zhang, “A hybrid plasmonic waveguide for subwavelength confinement and long-range propagation,” Nat. Photonics 2(8), 496–500 (2008). [CrossRef]

17.

D. J. Dikken, M. Spasenović, E. Verhagen, D. van Oosten, and L. K. Kuipers, “Characterization of bending losses for curved plasmonic nanowire waveguides,” Opt. Express 18(15), 16112–16119 (2010). [CrossRef] [PubMed]

18.

W. Wang, Q. Yang, F. Fan, H. Xu, and Z. L. Wang, “Light propagation in curved silver nanowire plasmonic waveguides,” Nano Lett. 11(4), 1603–1608 (2011). [CrossRef] [PubMed]

19.

A. V. Krasavin and A. V. Zayats, “Guiding light at the nanoscale: numerical optimization of ultrasubwavelength metallic wire plasmonic waveguides,” Opt. Lett. 36(16), 3127–3129 (2011). [CrossRef] [PubMed]

20.

D. F. P. Pile and D. K. Gramotnev, “Plasmonic subwavelength waveguides: next to zero losses at sharp bends,” Opt. Lett. 30(10), 1186–1188 (2005). [CrossRef] [PubMed]

21.

C. Yang, E. J. Teo, T. Goh, S. L. Teo, J. H. Teng, and A. A. Bettiol, “Metal-assisted photonic mode for ultrasmall bending with long propagation length at visible wavelengths,” Opt. Express 20(21), 23898–23905 (2012). [CrossRef] [PubMed]

22.

V. Krasavin and A. V. Zayats, “Three-dimensional numerical modeling of photonic integration with dielectric-loaded SPP waveguides,” Phys. Rev. B 78(4), 045425 (2008). [CrossRef]

23.

T. Holmgaard, Z. Chen, S. I. Bozhevolnyi, L. Markey, A. Dereux, A. V. Krasavin, and A. V. Zayats, “Bend- and splitting loss of dielectric-loaded surface plasmon-polariton waveguides,” Opt. Express 16(18), 13585–13592 (2008). [CrossRef] [PubMed]

24.

M. W. Kim and P. C. Ku, “Lasing in a metal-clad microring resonator,” Appl. Phys. Lett. 98(13), 131107 (2011). [CrossRef]

25.

H. S. Chu, Y. Akimov, P. Bai, and E. P. Li, “Submicrometer radius and highly confined plasmonic ring resonator filters based on hybrid metal-oxide-semiconductor waveguide,” Opt. Lett. 37(21), 4564–4566 (2012). [CrossRef] [PubMed]

26.

C. Horvath, D. Bachman, M. Wu, D. Perron, and V. Van, “Polymer hybrid plasmonic waveguide and microring resonators,” IEEE Photon. Technol. Lett. 23(17), 1267–1269 (2011). [CrossRef]

27.

D. Dai, Y. Shi, S. He, L. Wosinski, and L. Thylen, “Silicon hybrid plasmonic submicron-donut resonator with pure dielectric access waveguides,” Opt. Express 19(24), 23671–23682 (2011). [CrossRef] [PubMed]

28.

K. Y. Lee, N. LaBianca, S. A. Rishton, S. Zolgharnain, J. D. Gelorme, J. Shaw, and T. H.-P. Chang, “Micromachining applications of a high resolution ultrathick photoresist,” J. Vac. Sci. Technol. B 13(6), 3012–3016 (1995). [CrossRef]

29.

X. B. Phoeni, V., Enschede, The Netherlands (www.phoenixbv.com).

30.

S. M. García-Blanco, M. Pollnau, and S. I. Bozhevolnyi, “Loss compensation in long-range dielectric-loaded surface plasmon-polariton waveguides,” Opt. Express 19(25), 25298–25311 (2011). [CrossRef] [PubMed]

31.

K. R. Hiremath, M. Hammer, R. Stoffer, L. Prkna, and J. Čtyroký, “Analytic approach to dielectric optical bent slab waveguides,” Opt. Quantum Electron. 37(1-3), 37–61 (2005). [CrossRef]

32.

E. D. Palik, Handbook of Optical Constants of Solids (Academic Press, 1985).

OCIS Codes
(130.0130) Integrated optics : Integrated optics
(130.2790) Integrated optics : Guided waves
(160.3900) Materials : Metals
(240.6680) Optics at surfaces : Surface plasmons
(250.5460) Optoelectronics : Polymer waveguides
(250.5403) Optoelectronics : Plasmonics

ToC Category:
Integrated Optics

History
Original Manuscript: September 26, 2013
Revised Manuscript: November 15, 2013
Manuscript Accepted: November 17, 2013
Published: November 25, 2013

Citation
Mustafa Akin Sefunc, Markus Pollnau, and Sonia M. García-Blanco, "Low-loss sharp bends in polymer waveguides enabled by the introduction of a thin metal layer," Opt. Express 21, 29808-29817 (2013)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-21-24-29808


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. L. Eldada and L. W. Shacklette, “Advances in polymer integrated optics,” IEEE J. Sel. Top. Quantum Electron.6, 54–68 (2000).
  2. H. Ma, A. K. Y. Jen, and L. R. Dalton, “Polymer-based optical waveguides: materials, processing and devices,” Adv. Mater.14(19), 1339–1365 (2002). [CrossRef]
  3. B. Yang, L. Yang, R. Hu, Z. Sheng, D. Dai, Q. Liu, and S. He, “Fabrication and characterization of small optical ridge waveguides based on SU-8 polymer,” J. Lightwave Technol.27(18), 4091–4096 (2009). [CrossRef]
  4. L. Jin, J. Wang, X. Fu, B. Yang, Y. Shi, and D. Dai, “High-Q microring resonators with 2 × 2 angled multimode interference couplers,” IEEE Photon. Technol. Lett.25(6), 612–614 (2013). [CrossRef]
  5. Y. Shi, C. Zhang, H. Zhang, J. H. Bechtel, L. R. Dalton, B. H. Robinson, and W. H. Steier, “Low (sub-1-Volt) halfwave voltage polymeric electro-optic modulators achieved by controlling chromophore shape,” Science288(5463), 119–122 (2000). [CrossRef] [PubMed]
  6. Y. Yang, M. B. J. Diemeer, C. Grivas, G. Sengo, A. Driessen, and M. Pollnau, “Steady-state lasing in a solid polymer,” Laser Phys. Lett.7(9), 650–656 (2010). [CrossRef]
  7. X. Gong, M. Tong, Y. Xia, W. Cai, J. S. Moon, Y. Cao, G. Yu, C. L. Shieh, B. Nilsson, and A. J. Heeger, “High-detectivity polymer photodetectors with spectral response from 300 nm to 1450 nm,” Science325(5948), 1665–1667 (2009). [CrossRef] [PubMed]
  8. Q. Xu, D. Fattal, and R. G. Beausoleil, “Silicon microring resonators with 1.5-μm radius,” Opt. Express16, 4310–4315 (2008).
  9. Y. Deki, T. Hatanaka, M. Takahashi, T. Takeuchi, S. Watanabe, S. Takaesu, T. Miyazaki, M. Horie, and H. Yamazaki, “Wide-wavelength tunable lasers with 100 GHz FSR ring resonators,” Electron. Lett.43(4), 225–226 (2007). [CrossRef]
  10. S. I. Bozhevolnyi, V. S. Volkov, E. Devaux, J. Y. Laluet, and T. W. Ebbesen, “Channel plasmon subwavelength waveguide components including interferometers and ring resonators,” Nature440(7083), 508–511 (2006). [CrossRef] [PubMed]
  11. T. Holmgaard and S. I. Bozhevolnyi, “Theoretical analysis of dielectric-loaded surface plasmon-polariton waveguides,” Phys. Rev. B75(24), 245405 (2007). [CrossRef]
  12. T. Holmgaard, Z. Chen, S. I. Bozhevolnyi, L. Markey, and A. Dereux, “Dielectric-loaded plasmonic waveguide-ring resonators,” Opt. Express17(4), 2968–2975 (2009). [CrossRef] [PubMed]
  13. T. Holmgaard, J. Gosciniak, and S. I. Bozhevolnyi, “Long-range dielectric-loaded surface plasmon-polariton waveguides,” Opt. Express18(22), 23009–23015 (2010). [CrossRef] [PubMed]
  14. M. Z. Alam, J. Meier, J. S. Aitchison, and M. Mojahedi, “Super mode propagation in low index medium,” in Conference on Lasers and Electro-Optics/Quantum Electronics and Laser Science Conference and Photonic Applications Systems Technologies, OSA Technical Digest Series (CD) (Optical Society of America, 2007), paper JThD112.
  15. M. Z. Alam, J. Meier, J. S. Aitchison, and M. Mojahedi, “Propagation characteristics of hybrid modes supported by metal-low-high index waveguides and bends,” Opt. Express18(12), 12971–12979 (2010). [CrossRef] [PubMed]
  16. R. F. Oulton, V. J. Sorger, D. A. Genov, D. F. P. Pile, and X. Zhang, “A hybrid plasmonic waveguide for subwavelength confinement and long-range propagation,” Nat. Photonics2(8), 496–500 (2008). [CrossRef]
  17. D. J. Dikken, M. Spasenović, E. Verhagen, D. van Oosten, and L. K. Kuipers, “Characterization of bending losses for curved plasmonic nanowire waveguides,” Opt. Express18(15), 16112–16119 (2010). [CrossRef] [PubMed]
  18. W. Wang, Q. Yang, F. Fan, H. Xu, and Z. L. Wang, “Light propagation in curved silver nanowire plasmonic waveguides,” Nano Lett.11(4), 1603–1608 (2011). [CrossRef] [PubMed]
  19. A. V. Krasavin and A. V. Zayats, “Guiding light at the nanoscale: numerical optimization of ultrasubwavelength metallic wire plasmonic waveguides,” Opt. Lett.36(16), 3127–3129 (2011). [CrossRef] [PubMed]
  20. D. F. P. Pile and D. K. Gramotnev, “Plasmonic subwavelength waveguides: next to zero losses at sharp bends,” Opt. Lett.30(10), 1186–1188 (2005). [CrossRef] [PubMed]
  21. C. Yang, E. J. Teo, T. Goh, S. L. Teo, J. H. Teng, and A. A. Bettiol, “Metal-assisted photonic mode for ultrasmall bending with long propagation length at visible wavelengths,” Opt. Express20(21), 23898–23905 (2012). [CrossRef] [PubMed]
  22. V. Krasavin and A. V. Zayats, “Three-dimensional numerical modeling of photonic integration with dielectric-loaded SPP waveguides,” Phys. Rev. B78(4), 045425 (2008). [CrossRef]
  23. T. Holmgaard, Z. Chen, S. I. Bozhevolnyi, L. Markey, A. Dereux, A. V. Krasavin, and A. V. Zayats, “Bend- and splitting loss of dielectric-loaded surface plasmon-polariton waveguides,” Opt. Express16(18), 13585–13592 (2008). [CrossRef] [PubMed]
  24. M. W. Kim and P. C. Ku, “Lasing in a metal-clad microring resonator,” Appl. Phys. Lett.98(13), 131107 (2011). [CrossRef]
  25. H. S. Chu, Y. Akimov, P. Bai, and E. P. Li, “Submicrometer radius and highly confined plasmonic ring resonator filters based on hybrid metal-oxide-semiconductor waveguide,” Opt. Lett.37(21), 4564–4566 (2012). [CrossRef] [PubMed]
  26. C. Horvath, D. Bachman, M. Wu, D. Perron, and V. Van, “Polymer hybrid plasmonic waveguide and microring resonators,” IEEE Photon. Technol. Lett.23(17), 1267–1269 (2011). [CrossRef]
  27. D. Dai, Y. Shi, S. He, L. Wosinski, and L. Thylen, “Silicon hybrid plasmonic submicron-donut resonator with pure dielectric access waveguides,” Opt. Express19(24), 23671–23682 (2011). [CrossRef] [PubMed]
  28. K. Y. Lee, N. LaBianca, S. A. Rishton, S. Zolgharnain, J. D. Gelorme, J. Shaw, and T. H.-P. Chang, “Micromachining applications of a high resolution ultrathick photoresist,” J. Vac. Sci. Technol. B13(6), 3012–3016 (1995). [CrossRef]
  29. X. B. Phoeni, V., Enschede, The Netherlands ( www.phoenixbv.com ).
  30. S. M. García-Blanco, M. Pollnau, and S. I. Bozhevolnyi, “Loss compensation in long-range dielectric-loaded surface plasmon-polariton waveguides,” Opt. Express19(25), 25298–25311 (2011). [CrossRef] [PubMed]
  31. K. R. Hiremath, M. Hammer, R. Stoffer, L. Prkna, and J. Čtyroký, “Analytic approach to dielectric optical bent slab waveguides,” Opt. Quantum Electron.37(1-3), 37–61 (2005). [CrossRef]
  32. E. D. Palik, Handbook of Optical Constants of Solids (Academic Press, 1985).

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Supplementary Material


» Media 1: MPG (2942 KB)     
» Media 2: MPG (3194 KB)     
» Media 3: MPG (2972 KB)     
» Media 4: MPG (3246 KB)     

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited