OSA's Digital Library

Optics Express

Optics Express

  • Editor: Andrew M. Weiner
  • Vol. 22, Iss. 11 — Jun. 2, 2014
  • pp: 13366–13373
« Show journal navigation

Generation of mode-locked optical pulses at 1035 nm from a fiber Bragg grating stabilized semiconductor laser diode

Peh Siong Teh, Shaif-ul Alam, David P. Shepherd, and David J. Richardson  »View Author Affiliations


Optics Express, Vol. 22, Issue 11, pp. 13366-13373 (2014)
http://dx.doi.org/10.1364/OE.22.013366


View Full Text Article

Acrobat PDF (1316 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We report the generation of transform-limited, ~18 ps optical pulses from a fiber Bragg grating (FBG) stabilized semiconductor laser diode. Up to 7.2 pJ of pulse energy and a peak power of 400mW were achieved when operating at a repetition frequency of 832.6 MHz, a multiple of the cavity (diode + FBG) free spectral range (FSR). A small detuning in the repetition frequency resulted in broader optical pulses. We have shown experimentally the transition from a gain-switched regime of operation to mode-locked operation once the injection current modulation frequency is set to match a harmonic of the cavity FSR. The transition also results in a reduction in the timing jitter of the optical pulses.

© 2014 Optical Society of America

1. Introduction

The demand for high power fiber lasers producing picosecond optical pulses in the 1.0 µm wavelength region has grown significantly in recent years with such lasers widely used for applications such as laser machining and frequency conversion (e.g. frequency-doubling, the pumping of parametric oscillators and supercontinuum generation [1

1. F. Kienle, P. S. Teh, D. Lin, S. U. Alam, J. H. V. Price, D. C. Hanna, D. J. Richardson, and D. P. Shepherd, “High-power, high repetition-rate, green-pumped, picosecond LBO optical parametric oscillator,” Opt. Express 20(7), 7008–7014 (2012). [CrossRef] [PubMed]

3

3. K. K. Chen, S. U. Alam, J. H. V. Price, J. R. Hayes, D. Lin, A. Malinowski, C. Codemard, D. Ghosh, M. Pal, S. K. Bhadra, and D. J. Richardson, “Picosecond fiber MOPA pumped supercontinuum source with 39 W output power,” Opt. Express 18(6), 5426–5432 (2010). [CrossRef] [PubMed]

]). Semiconductor Laser Diode (SLD) seeded, fiber MOPA sources represent highly attractive sources for such applications, combining the compactness, stability and cost-effectiveness associated with semiconductor devices with the ready power-scaling possible using fiber amplifiers. Two primary techniques can be used to obtain picosecond pulses from an SLD: namely gain-switching and mode-locking.

Gain-switching provides a simple technique for the generation of picosecond optical pulses directly from an SLD with the added flexibility of generating a pulse on demand [5

5. K. Y. Lau, “Gain switching of semiconductor injection lasers,” Appl. Phys. Lett. 52(4), 257–259 (1988). [CrossRef]

]. Optical pulses with a duration of tens of picoseconds have been demonstrated in the 1.06 µm wavelength region using this approach. However, there are a few issues associated with this technique that one needs to be mindful of. The minimum pulse duration is dictated by the device properties and parameters of the modulated current used to drive it and the optical pulses generated usually inherit a significant chirp due to the time-varying carrier density within the gain medium which leads to a large transient refractive index modulation. This results in chirped optical pulses with a corresponding time-bandwidth-product that can be many times the Fourier limit. Several techniques to compensate this chirp have been demonstrated in recent years but these all bring significant additional complexity to the setup. Approaches demonstrated include the use of a chirped fiber Bragg grating (CFBG) [6

6. K. K. Chen, J. H. V. Price, S. U. Alam, J. R. Hayes, D. Lin, A. Malinowski, and D. J. Richardson, “Polarisation maintaining 100W Yb-fiber MOPA producing microJ pulses tunable in duration from 1 to 21 ps,” Opt. Express 18(14), 14385–14394 (2010). [CrossRef] [PubMed]

], a length of dispersive fiber [7

7. K. A. Ahmed, H. F. Liu, N. Onodera, P. Lee, R. S. Tucker, and Y. Ogawa, “Nearly transform-limited pulse (3.6 ps) generation from gain-swtiched 1-55 um distributed feeback laser by using fibre compression technique,” Electron. Lett. 29(1), 54 (1993). [CrossRef]

], a nonlinear optical loop mirror [8

8. C. de Dios and H. Lamela, “Improvements to long-duration low-power gain-switching diode laser pulses using a highly nonlinear optical loop mirror: Theory and experiment,” J. Lightw. Tech. 29, 700–707 (2011).

] and spectral filtering using a Mach-Zehnder interferometer [9

9. A. Consoli and I. Esquivias, “Pulse shortening of gain switched single mode semiconductor lasers using a variable delay interferometer,” Opt. Express 20(20), 22481–22489 (2012). [CrossRef] [PubMed]

]. A further issue is that gain-switched optical pulses typically suffer from pulse-to-pulse timing jitter which is associated with the build-up of optical pulses from spontaneous emission which causes random fluctuation in the photon density [10

10. D.-S. Seo, H.-F. Liu, D. Y. Kim, and D. D. Sampson, “Injection power and wavelength dependence of an external-seeded gain-switched Fabry–Perot laser,” Appl. Phys. Lett. 67(11), 1503–1505 (1995). [CrossRef]

].

Herein, we experimentally demonstrate a simple cavity configuration that allows the generation of transform-limited 18 ps optical pulses with an energy of 7.2 pJ, corresponding to a peak power of 400 mW in the 1.0 µm wavelength region. Our experimental results show that the mode-locking mechanism plays a key role in enabling short and stable optical pulses.

2. Experimental setup

Figure 1
Fig. 1 Experimental setup.
shows schematic of the experimental setup. The semiconductor laser diode used in this experiment was a commercial Fabry-Perot SLD (OCLARO LC96A1030-20R) with a gain peak located at 1035 nm. The measured longitudinal mode spacing was 0.032 nm and the measured threshold current was 25 mA. The SLD was mounted on a modified printed circuit board (PCB) with resistors placed in series in order to match the impedance of the transmission line. The temperature of the SLD was stabilized by using a thermoelectric cooler (TEC) unit. A combination of a pulse generator and RF amplifier drove the SLD with a stable train of sinusoidal electrical pulses. The drive current had a peak-to-peak current of 632 mA which was superimposed on a DC bias current of 20 mA - slightly less than the threshold current to avoid a CW leakage signal. The pigtail of the SLD was spliced to a polarization maintaining 1035 nm FBG with a 3 dB bandwidth of 0.24 nm and a reflectivity of ~12%. The fiber length between the SLD and the FBG was ~2 m. The FSR of the cavity was ~52.04 MHz. For most of our experiments the system was operated at 832.6 MHz which corresponds to the 16th harmonic of the cavity FSR. A polarization maintaining 3-dB fused fiber coupler was spliced to the output end of the grating so that both temporal and spectral profiles could be measured simultaneously with a Digital Communication Analyzer (DCA) and an Optical Spectrum Analyzer (OSA) respectively.

3. Results and discussion

When the injection current modulation frequency (ICMF) was detuned relative to the harmonic of the cavity FSR, pulses with a broad optical spectrum with a full width at half maximum (FWHM) of approximately 6 nm and a pulse width of ~94 ps were measured, as illustrated by the red colored lines in Fig. 2
Fig. 2 Spectral profiles of the gain-switched laser diode with (black line) and without (red line) FBG. (Inset) Temporal profiles for the seeded (black line) and unseeded (red line) cases.
. In such circumstances the SLD operated in a gain-switching (GS) mode as a result of the high drive current pulse of sub-ns duration. The broad spectrum generated consisted of a large number of longitudinal modes. The emitted optical pulses exhibited a strong red-shift in wavelength from the leading to trailing edge corresponding to a very significant chirp. The estimated time bandwidth product of the pulses is ~158. Moreover, the pulses exhibited significant intensity noise (~15%) and the RMS time jitter was measured to be 5 ps.

Once the ICMF was tuned to 832.6 MHz we observed substantial reductions in both the spectral bandwidth and the pulse width as shown by the black colored lines in Fig. 2. Furthermore, transform-limited optical pulses of 18 ps were measured with an intensity autocorrelator as shown in the inset of Fig. 3(a)
Fig. 3 (a) Pulse train measured at 16th harmonic (832.6 MHz). (Inset) Trace of intensity autocorrelator indicating ~18 ps optical pulses and (b) amplitude and frequency chirp as a function of delay obtained using a linear FROG technique.
. This corresponds to an almost 5 times reduction in pulse width as compared to that of the GS case. A spectral Side-Mode Suppression Ratio (SMSR) of ~50 dB and a FWHM spectral bandwidth of 0.09 nm were measured corresponding to an almost 67 times compression in the spectral domain. Furthermore, the optical pulses were far more stable as compared to the GS case. The RMS timing jitter was estimated to be ~316 fs through the RF-spectra measurement method proposed by von der Linde [15

15. D. Linde, “Characterization of the noise in continuously operating mode-locked lasers,” Appl. Phys. B 39(4), 201–217 (1986). [CrossRef]

]. The average optical power was measured to be ~6 mW corresponding to a pulse energy of 7.2 pJ. A highly stable train of optical pulses was measured with a fast photo-detector (Agilent 83440D) and a DCA as shown in Fig. 3(a).

The optical pulses were then characterized through the use of a linear frequency-resolved optical gating (FROG) technique. An electro-optic modulator (EOM) was used as a gate to temporally slice the pulses which were then spectrally resolved [16

16. K. T. Vu, A. Malinowski, M. A. F. Roelens, M. Ibsen, P. Petropoulos, and D. J. Richardson, “Full characterization of low-power picosecond pulses from a gain-switched diode laser using electrooptic modulation-based linear FROG,” IEEE Photonics Technology Letters 20(7), 505–507 (2008). [CrossRef]

]. Information such as the temporal shape (black line) and chirp (blue dash line) across the optical pulses can be retrieved with this method as shown in Fig. 3(b). Figure 3(b) clearly illustrates that the measured chirp was constant across the central region of the optical pulse and increases linearly at the trailing edge due to the existence of a small secondary peak ~35 ps away from the main pulse. The estimated time bandwidth product (TBP) of 0.45 indicates that the output pulses were time-bandwidth limited (assuming a Gaussian shaped optical pulse).

A small detune in ICMF resulted in a substantial change in pulse widths and pulse shapes, similar to that reported in [17

17. A. J. Lowery, N. Onodera, and R. Tucker, “Stability and spectral behavior of grating-controlled actively mode-locked lasers,” IEEE Journal of Quantum Electronics 27(11), 2422–2430 (1991). [CrossRef]

]. Figure 4
Fig. 4 Optical pulse width measured at different repetition frequencies and (color) the corresponding optical pulse shapes.
shows the variation in pulse width as the operating frequency was varied with the inclusion of the detailed pulse shapes observed.

At ICMFs below 832.0 MHz, broad, distorted and unstable optical pulses were observed similar to that of GS case. Increasing the ICMF to 832.2 MHz resulted in more stable but broad (90 ps) asymmetrical optical pulses with a long trailing edge. Furthermore, the pulses exhibited a double peak structure with the leading peak slightly broader than the trailing peak. The evolution of double peak optical pulses at frequencies just below the cavity resonance frequency can be explained as follows. For a fixed cavity length the time of flight of the pulses remains effectively constant irrespective of the operating frequency. Therefore at frequencies just below the harmonic cavity resonance frequency, the reflected pulses arrive back at the active region whilst the carrier density is still building up due to the ever so slightly longer time interval between the injected current pulses. Consequently a portion of the carrier density gets depleted through stimulated emission however the carrier density continues to build up in the presence of the current pulse. A second optical pulse evolves when the excess carrier density reaches the threshold condition.

An increase in ICMF to 832.4 MHz resulted in a reduction in the energy contained within the secondary peak due to insufficient recovery of the carrier density

When the ICMF was tuned to 832.6 MHz, a harmonic of the cavity FSR, short optical pulses with a width of ~18 ps were obtained. In this instance, the returning pulse arrives at the active region when the carrier density is at its maximum. This resulted in the highest peak power of 400mW that can be extracted cleanly from the mode locked laser diode, although a small secondary peak was still observable at the trailing edge of the main pulse. Note however that we managed to eliminate the secondary pulse completely by reducing the DC bias current down from 20 mA to 15 mA.

As the ICMF was further increased to 832.8 MHz and 833.0 MHz, the pulse width broadened to 30 ps and 40 ps respectively and both amplitude and timing jitter started to become significant with increasing frequency detuning. Beyond 833 MHz mode-locking was completely lost and the optical pulses returned to those characteristic of pure GS operation with a pulse width of ~94 ps.

The lasing wavelength of the output pulses was also affected when the ICMF was detuned. The optical spectra measured at various ICMF are plotted in Fig. 5
Fig. 5 Optical spectra measured for a range of injection current modulation frequencies showing the observed wavelength shift with respect to the central wavelength of the FBG.
. The central wavelength at different frequency detunings was compared relative to the FBG’s peak reflectivity wavelength in order to quantify the accumulated shift in wavelength. We observed a red-shift of the central wavelength as the ICMF was increased to 832.0 MHz and 832.2 MHz. However, as soon as the ICMF was tuned to 832.6 MHz, a maximum wavelength shift of 0.1 nm was measured. We also observed that the spectrum exhibited an asymmetrical shape with a tail in the short wavelength region. Any further increase in repetition frequency resulted in a broader spectrum and a reduction in the wavelength shift. A similar red-shift in central wavelength was also observed in [13

13. P. A. Morton, V. Mizrahi, P. A. Andrekson, T. Tanbun-Ek, R. A. Logan, P. Lemaire, D. L. Coblentz, A. M. Sergent, K. W. Wecht, and P. F. Sciortino Jr., “Mode-locked hybrid soliton pulse source with extremely wide operating frequency range,” IEEE Photonics Technology Letters 5(1), 28–31 (1993). [CrossRef]

, 17

17. A. J. Lowery, N. Onodera, and R. Tucker, “Stability and spectral behavior of grating-controlled actively mode-locked lasers,” IEEE Journal of Quantum Electronics 27(11), 2422–2430 (1991). [CrossRef]

, 18

18. N. Dogru, “Effect of grating parameters on mode-locked external cavity lasers,” IEEE Journal, Selected Topics in Quantum Electronics 15(3), 644–652 (2009). [CrossRef]

] suggesting that when the ICMF was changed, the device self-tuned its operating wavelength in order to maintain the correct effective cavity length needed to maintain resonance with the drive current signal.

The stability of the mode-locking mechanism depends on the reflectivity of the FBG. In this work, we examined three uniform pitch FBGs of different reflectivity, namely 4%, 8% and 12%. We observed that mode-locking was unstable when a 4% reflectivity grating was used. The stability and shape of the optical pulse varied randomly over a period of time. Much better mode-locking was achieved with a 7% reflectivity FBG. However, environmental conditions such as changes in temperature of the air surrounding the FBG affected the stability of the optical pulses over a longer time scale and fine adjustment of the TEC was necessary from time to time to recover the optimum stable mode-locking condition. On the other hand, when a 12% reflectivity FBG was used stable mode-locked operation was accomplished without the need for periodic tweaking of the temperature controller highlighting the fact that the strength of the external cavity feedback is important in sustaining uninterrupted mode locked operation - mode competition between the SLD modes and that of the external cavity is less well controlled with a weaker grating resulting in unstable mode locked operation.

Since the constituent longitudinal modes of a mode-locked optical pulse will have a defined phase relationship, an interference measurement based on a fiber based Mach-Zehnder interferometer that enabled the interference between one pulse and that emitted 9 pulse periods later was carried out to confirm that the mode-locking mechanism is indeed responsible for the generation of the short optical pulses observed. Interference patterns are clearly visible in the spectral domains as shown in Fig. 6
Fig. 6 Interference patterns between the 1st and the 10th optical pulses for two different operating frequencies corresponding to different operating regimes. The separation between peaks corresponds to the temporal separation between the two interfered optical pulses.
for ICMF of 832.6 MHz and 833 MHz. The interference pattern was lost completely above 833 MHz and at or below 832.0 MHz, indicating that the mode-locking mechanisms no longer exist in these operating regimes. Instead, injection seeding dominates the pulse generation process.

4. Conclusion

We have demonstrated a simple cavity configuration incorporating a gain switched SLD and an external FBG capable of generating transform-limited 18 ps optical pulses with a pulse energy of 7.2 pJ and peak power of 400 mW. We have shown that the mode-locking mechanism is responsible for the generation of the shortest picosecond optical pulses observed. We have also investigated the impact of injection current modulation frequency on the spectral and temporal evolution of the pulses. The combination of the excellent stability of the optical pulse produced and simplicity of this seed configuration make this SLD based system an attractive seed source for picosecond MOPA systems.

Acknowledgments

The authors acknowledge A.Heidt, M.Berendt and M.Tokurakawa for their valuable discussions and Peh Siong Teh thanks the Public Service Department (PSD) of Malaysia for their financial support. This work was supported in part by the UK Technology Strategy Board project SMART LASER Manufacturing (TP14/HVM/6/I/BD566F) and the UK EPSRC project EP/I02798X/1.

References and links

1.

F. Kienle, P. S. Teh, D. Lin, S. U. Alam, J. H. V. Price, D. C. Hanna, D. J. Richardson, and D. P. Shepherd, “High-power, high repetition-rate, green-pumped, picosecond LBO optical parametric oscillator,” Opt. Express 20(7), 7008–7014 (2012). [CrossRef] [PubMed]

2.

A. Ancona, S. Döring, C. Jauregui, F. Röser, J. Limpert, S. Nolte, and A. Tünnermann, “Femtosecond and picosecond laser drilling of metals at high repetition rates and average powers,” Opt. Lett. 34(21), 3304–3306 (2009). [CrossRef] [PubMed]

3.

K. K. Chen, S. U. Alam, J. H. V. Price, J. R. Hayes, D. Lin, A. Malinowski, C. Codemard, D. Ghosh, M. Pal, S. K. Bhadra, and D. J. Richardson, “Picosecond fiber MOPA pumped supercontinuum source with 39 W output power,” Opt. Express 18(6), 5426–5432 (2010). [CrossRef] [PubMed]

4.

J. Yoonchan, J. Nilsson, J. K. Sahu, D. N. Payne, R. Horley, L. M. B. Hickey, and P. W. Turner, “Power scaling of single-frequency Ytterbium-doped fiber master-oscillator power-amplifier sources up to 500 W,” IEEE Selected Topics in Quantum Electronics 13(3), 546–551 (2007). [CrossRef]

5.

K. Y. Lau, “Gain switching of semiconductor injection lasers,” Appl. Phys. Lett. 52(4), 257–259 (1988). [CrossRef]

6.

K. K. Chen, J. H. V. Price, S. U. Alam, J. R. Hayes, D. Lin, A. Malinowski, and D. J. Richardson, “Polarisation maintaining 100W Yb-fiber MOPA producing microJ pulses tunable in duration from 1 to 21 ps,” Opt. Express 18(14), 14385–14394 (2010). [CrossRef] [PubMed]

7.

K. A. Ahmed, H. F. Liu, N. Onodera, P. Lee, R. S. Tucker, and Y. Ogawa, “Nearly transform-limited pulse (3.6 ps) generation from gain-swtiched 1-55 um distributed feeback laser by using fibre compression technique,” Electron. Lett. 29(1), 54 (1993). [CrossRef]

8.

C. de Dios and H. Lamela, “Improvements to long-duration low-power gain-switching diode laser pulses using a highly nonlinear optical loop mirror: Theory and experiment,” J. Lightw. Tech. 29, 700–707 (2011).

9.

A. Consoli and I. Esquivias, “Pulse shortening of gain switched single mode semiconductor lasers using a variable delay interferometer,” Opt. Express 20(20), 22481–22489 (2012). [CrossRef] [PubMed]

10.

D.-S. Seo, H.-F. Liu, D. Y. Kim, and D. D. Sampson, “Injection power and wavelength dependence of an external-seeded gain-switched Fabry–Perot laser,” Appl. Phys. Lett. 67(11), 1503–1505 (1995). [CrossRef]

11.

P. A. Morton, R. Adar, R. C. Kistler, C. H. Henry, T. Tanbun-Ek, R. A. Logan, D. L. Coblentz, A. M. Sergent, and K. W. Wecht, “Hybrid soliton pulse source using a silica waveguide external cavity and Bragg reflector,” Appl. Phys. Lett. 59(23), 2944–2946 (1991). [CrossRef]

12.

Z. Ahmed, L. Zhai, A. J. Lowery, N. Onodera, and R. Tucker, “Locking bandwidth of actively mode-locked semiconductor lasers,” IEEE Journal of Quantum Electronics 29(6), 1714–1721 (1993). [CrossRef]

13.

P. A. Morton, V. Mizrahi, P. A. Andrekson, T. Tanbun-Ek, R. A. Logan, P. Lemaire, D. L. Coblentz, A. M. Sergent, K. W. Wecht, and P. F. Sciortino Jr., “Mode-locked hybrid soliton pulse source with extremely wide operating frequency range,” IEEE Photonics Technology Letters 5(1), 28–31 (1993). [CrossRef]

14.

R. Paoletti, D. Bertone, R. Fang, G. Magnetti, M. Meliga, G. Meneghini, G. Morello, G. Rossi, L. Tallone, and M. Scofet, “Repetition rate, using a mode-locked hybrid distributed Bragg reflector (ML-HDBR) laser source,” IEEE Photonics Technology Letters 12(3), 245–247 (2000). [CrossRef]

15.

D. Linde, “Characterization of the noise in continuously operating mode-locked lasers,” Appl. Phys. B 39(4), 201–217 (1986). [CrossRef]

16.

K. T. Vu, A. Malinowski, M. A. F. Roelens, M. Ibsen, P. Petropoulos, and D. J. Richardson, “Full characterization of low-power picosecond pulses from a gain-switched diode laser using electrooptic modulation-based linear FROG,” IEEE Photonics Technology Letters 20(7), 505–507 (2008). [CrossRef]

17.

A. J. Lowery, N. Onodera, and R. Tucker, “Stability and spectral behavior of grating-controlled actively mode-locked lasers,” IEEE Journal of Quantum Electronics 27(11), 2422–2430 (1991). [CrossRef]

18.

N. Dogru, “Effect of grating parameters on mode-locked external cavity lasers,” IEEE Journal, Selected Topics in Quantum Electronics 15(3), 644–652 (2009). [CrossRef]

OCIS Codes
(140.4050) Lasers and laser optics : Mode-locked lasers
(250.5980) Optoelectronics : Semiconductor optical amplifiers

ToC Category:
Lasers and Laser Optics

History
Original Manuscript: March 24, 2014
Revised Manuscript: May 8, 2014
Manuscript Accepted: May 8, 2014
Published: May 27, 2014

Citation
Peh Siong Teh, Shaif-ul Alam, David P. Shepherd, and David J. Richardson, "Generation of mode-locked optical pulses at 1035 nm from a fiber Bragg grating stabilized semiconductor laser diode," Opt. Express 22, 13366-13373 (2014)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-22-11-13366


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. F. Kienle, P. S. Teh, D. Lin, S. U. Alam, J. H. V. Price, D. C. Hanna, D. J. Richardson, D. P. Shepherd, “High-power, high repetition-rate, green-pumped, picosecond LBO optical parametric oscillator,” Opt. Express 20(7), 7008–7014 (2012). [CrossRef] [PubMed]
  2. A. Ancona, S. Döring, C. Jauregui, F. Röser, J. Limpert, S. Nolte, A. Tünnermann, “Femtosecond and picosecond laser drilling of metals at high repetition rates and average powers,” Opt. Lett. 34(21), 3304–3306 (2009). [CrossRef] [PubMed]
  3. K. K. Chen, S. U. Alam, J. H. V. Price, J. R. Hayes, D. Lin, A. Malinowski, C. Codemard, D. Ghosh, M. Pal, S. K. Bhadra, D. J. Richardson, “Picosecond fiber MOPA pumped supercontinuum source with 39 W output power,” Opt. Express 18(6), 5426–5432 (2010). [CrossRef] [PubMed]
  4. J. Yoonchan, J. Nilsson, J. K. Sahu, D. N. Payne, R. Horley, L. M. B. Hickey, P. W. Turner, “Power scaling of single-frequency Ytterbium-doped fiber master-oscillator power-amplifier sources up to 500 W,” IEEE Selected Topics in Quantum Electronics 13(3), 546–551 (2007). [CrossRef]
  5. K. Y. Lau, “Gain switching of semiconductor injection lasers,” Appl. Phys. Lett. 52(4), 257–259 (1988). [CrossRef]
  6. K. K. Chen, J. H. V. Price, S. U. Alam, J. R. Hayes, D. Lin, A. Malinowski, D. J. Richardson, “Polarisation maintaining 100W Yb-fiber MOPA producing microJ pulses tunable in duration from 1 to 21 ps,” Opt. Express 18(14), 14385–14394 (2010). [CrossRef] [PubMed]
  7. K. A. Ahmed, H. F. Liu, N. Onodera, P. Lee, R. S. Tucker, Y. Ogawa, “Nearly transform-limited pulse (3.6 ps) generation from gain-swtiched 1-55 um distributed feeback laser by using fibre compression technique,” Electron. Lett. 29(1), 54 (1993). [CrossRef]
  8. C. de Dios, H. Lamela, “Improvements to long-duration low-power gain-switching diode laser pulses using a highly nonlinear optical loop mirror: Theory and experiment,” J. Lightw. Tech. 29, 700–707 (2011).
  9. A. Consoli, I. Esquivias, “Pulse shortening of gain switched single mode semiconductor lasers using a variable delay interferometer,” Opt. Express 20(20), 22481–22489 (2012). [CrossRef] [PubMed]
  10. D.-S. Seo, H.-F. Liu, D. Y. Kim, D. D. Sampson, “Injection power and wavelength dependence of an external-seeded gain-switched Fabry–Perot laser,” Appl. Phys. Lett. 67(11), 1503–1505 (1995). [CrossRef]
  11. P. A. Morton, R. Adar, R. C. Kistler, C. H. Henry, T. Tanbun-Ek, R. A. Logan, D. L. Coblentz, A. M. Sergent, K. W. Wecht, “Hybrid soliton pulse source using a silica waveguide external cavity and Bragg reflector,” Appl. Phys. Lett. 59(23), 2944–2946 (1991). [CrossRef]
  12. Z. Ahmed, L. Zhai, A. J. Lowery, N. Onodera, R. Tucker, “Locking bandwidth of actively mode-locked semiconductor lasers,” IEEE Journal of Quantum Electronics 29(6), 1714–1721 (1993). [CrossRef]
  13. P. A. Morton, V. Mizrahi, P. A. Andrekson, T. Tanbun-Ek, R. A. Logan, P. Lemaire, D. L. Coblentz, A. M. Sergent, K. W. Wecht, P. F. Sciortino., “Mode-locked hybrid soliton pulse source with extremely wide operating frequency range,” IEEE Photonics Technology Letters 5(1), 28–31 (1993). [CrossRef]
  14. R. Paoletti, D. Bertone, R. Fang, G. Magnetti, M. Meliga, G. Meneghini, G. Morello, G. Rossi, L. Tallone, M. Scofet, “Repetition rate, using a mode-locked hybrid distributed Bragg reflector (ML-HDBR) laser source,” IEEE Photonics Technology Letters 12(3), 245–247 (2000). [CrossRef]
  15. D. Linde, “Characterization of the noise in continuously operating mode-locked lasers,” Appl. Phys. B 39(4), 201–217 (1986). [CrossRef]
  16. K. T. Vu, A. Malinowski, M. A. F. Roelens, M. Ibsen, P. Petropoulos, D. J. Richardson, “Full characterization of low-power picosecond pulses from a gain-switched diode laser using electrooptic modulation-based linear FROG,” IEEE Photonics Technology Letters 20(7), 505–507 (2008). [CrossRef]
  17. A. J. Lowery, N. Onodera, R. Tucker, “Stability and spectral behavior of grating-controlled actively mode-locked lasers,” IEEE Journal of Quantum Electronics 27(11), 2422–2430 (1991). [CrossRef]
  18. N. Dogru, “Effect of grating parameters on mode-locked external cavity lasers,” IEEE Journal, Selected Topics in Quantum Electronics 15(3), 644–652 (2009). [CrossRef]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited