OSA's Digital Library

Optics Express

Optics Express

  • Editor: J. H. Eberly
  • Vol. 8, Iss. 11 — May. 21, 2001
  • pp: 605–610
« Show journal navigation

Locking a microsphere whispering-gallery mode to a laser

J. P. Rezac and A. T. Rosenberger  »View Author Affiliations


Optics Express, Vol. 8, Issue 11, pp. 605-610 (2001)
http://dx.doi.org/10.1364/OE.8.000605


View Full Text Article

Acrobat PDF (191 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We have locked a whispering-gallery resonance of a fused-silica microsphere to a frequency-scanning laser. The resonance frequency is modulated by axial compression of the microsphere, and phase-sensitive detection of the fiber-coupled optical throughput is used for locking. Using a laser wavelength of either 1570 nm or 830 nm, we demonstrate a locked tracking range exceeding 30 GHz for a microsphere of 120 GHz free spectral range. This performance has been enabled by an improved compression tuner design that allows coarse tuning over 1 THz and piezoelectric tuning over 80 GHz. Compression modulation rates of up to 13 kHz have also been achieved with this tuner.

© Optical Society of America

In this article we report a new application for a compression tuner and the advances in compression tuning that make it possible. The advances include extending the tuning range (in units of the FSR) and enhancing the response speed; these enable locking to a laser, keeping a single WGM on resonance as the laser frequency is scanned. For our experiments, a microsphere was fabricated by torch-melting the end of an optical fiber; the microsphere used in this work had a diameter of 550 µm. A tapered fiber in contact with the sphere was used for coupling to the WGMs [14

14. J. C. Knight, G. Cheung, F. Jacques, and T. A. Birks, “Phase-matched excitation of whispering-gallery mode resonances by a fiber taper,” Opt. Lett. 22, 1129–1131 (1997). [CrossRef] [PubMed]

,15

15. M. Cai, O. Painter, and K. J. Vahala, “Observation of Critical Coupling in a Fiber Taper to a Silica-Microsphere Whispering-Gallery Mode System,” Phys. Rev. Lett. 85, 74–77 (2000). [CrossRef] [PubMed]

]. Light from a tunable laser, either an extended-cavity diode used at 1570 nm or a cw Ti:sapphire used at 830 nm, was launched into a single-mode fiber (SMF-28) that was angle-polished at the injection face (8° from normal) to prevent back reflection into the laser. In the fiber-microsphere coupling region, the fiber was tapered by heating and stretching a short section to a diameter of 20 µm or less, followed by hydrofluoric-acid etching to a 5–10 µm diameter. A fiber polarization controller allowed excitation of either tangentially polarized (TE) or radially polarized (TM) WGMs. The fiber throughput was detected as either the laser or microsphere was tuned, with sharp dips in transmitted power indicating the excitation of WGMs. The width of a dip gave a loaded-sphere quality factor Q of (typically) 2×106. Although better than 90% extinction could be achieved using optimal taper size and alignment, in these experiments the typical extinction was about 20%.

Besides the polarization, three integers are needed to specify a WGM. The mode number is, approximately, the number of wavelengths in the sphere’s circumference. The mode order q is the number of radial intensity maxima, and -|m|+1(where |m|≤) gives the number of maxima in “latitude”. The “fundamental” WGM has q=1 and |m|= and thus a single transverse maximum. The WGM resonant frequencies are approximately [4

4. V. V. Vassiliev, V. L. Velichansky, V. S. Ilchenko, M. L. Gorodetsky, L. Hollberg, and A. V. Yarovitsky, “Narrow-line-width diode laser with a high-Q microsphere resonator,” Opt. Commun. 158, 305–312 (1998). [CrossRef]

]

νqℓmi=δ[+12+Aq(+122)13Δi+(m)aeaaa].
(1)

In Eq. (1), i denotes TE or TM, δ=c/2πaen is the microsphere’s nominal free spectral range, n is the index of refraction of the sphere, a is the sphere radius (ae, equatorial; aa, axial), the Δi are polarization-dependent shifts, and Aq is the q th zero of the Airy function: Ai(-Aq)=0. In forming a microsphere, a small amount of eccentricity results, so that ae and aa typically differ by about 1% [4

4. V. V. Vassiliev, V. L. Velichansky, V. S. Ilchenko, M. L. Gorodetsky, L. Hollberg, and A. V. Yarovitsky, “Narrow-line-width diode laser with a high-Q microsphere resonator,” Opt. Commun. 158, 305–312 (1998). [CrossRef]

,11

11. V. S. Ilchenko, P. S. Volikov, V. L. Velichansky, F. Treussart, V. Lefèvre-Seguin, J.-M. Raimond, and S. Haroche, “Strain-tunable high-Q optical microsphere resonator,” Opt. Commun. 145, 86–90 (1998). [CrossRef]

]. Axial compression of the microsphere results in tuning of the WGM frequencies, given in terms of the fractional change in axial radius as

Δνν=Δaaaμ[1+bi(1+μμ)m].
(2)

The first and second terms in Eq. (2) come from the changes in δ due to changes in ae and n, respectively. The third term results from the change in eccentricity, and tuning due to the change in Δi is negligible. Because our tuner’s contact-surface configuration is not too different from that of Ref. 11, we use their strain calculation results to estimate the relative contributions of the three terms. Specifically, we take the effective Poisson ratio µ to be µ=|Δaeaa|=0.11 (rather than the handbook value of 0.17) and the photoelastic contribution to be bTE=-0.14 or b=0.07. Since ≈1500 for our sphere at 1570 nm, the third term contributes -0.16 for -|m|=24, and so the geometrical path length change given by the first term in Eq. (2) dominates the tuning. (The value of -|m|=24 used above is an estimate for the maximum observed here, as very long frequency scans showed families of 20–25 modes with ~1 GHz spacing, each with a bandhead that is probably the |m|= mode.)

Fig. 1. Compression tuner. (a) Main body is 44×38×6-mm aluminum. (b) Stainless steel brace minimizes flexing of main body. (c) Piezoelectric actuator. (d) Manual tuning screw. (e) Hardened steel compression pad. (f) Stainless steel hypodermic tubing, inserted into hole in lower steel pad.

Fig. 2. Unlocked and locked frequency scans at 1570 nm. (a)–(d) Unlocked: WGM mode spectrum observed as the laser is scanned over a 19 GHz range; an increasing frequency shift is seen for PZT bias voltages of 68 V, 88 V, 118 V, and 130 V, respectively. The baseline for trace (a) is at the frequency axis, and successive traces have been displaced vertically. (e) Locked: frequency scan where the WGM with the deepest dip in (a)–(d) is locked to the laser. The baseline is the same as for trace (d). No mode hops are observed.

For locking a WGM to the laser, we used a commercial lock-in stabilizer designed for the stabilization of CO2 lasers. Its 518 Hz locking modulation signal and dc bias were combined in a capacitive voltage divider for application to the PZT; the applied locking modulation was a 30–60 mV peak-to-peak dither and the applied bias was 0–150 V. We chose to lock under conditions that would provide a stringent test of the stability of the technique and so provided no isolation from building vibration or air currents. Furthermore, the diameter and alignment of the coupling fiber taper were chosen so that many modes were excited, as seen in Fig. 2, where the 1570-nm laser was scanned over 19 GHz. The four laser frequency scans in traces (a)–(d) of Fig. 2 are over the same range, with different constant bias voltages (and no locking dither) applied to the PZT. All modes have the same polarization here, but there is some variability in their relative positions from (a) through (d) because of the slightly different tuning rates for modes of different m. The deepest dip, indicating about 20% extinction and Q≈2×106, is the one to which we locked. A scan of the same range, with that mode now locked to the laser, is shown in Fig. 2(e). Note that the slow power variation (from frequency dependence of the fiber transmission) is the same in (a)–(e). From (e), it is evident that the locking never switches to a different mode, because doing so would result in an obvious displacement of the trace. The larger fluctuations on this trace may indicate the temporary overlap of a differentially-tuning mode with the locked one; the noise level is consistent with the approximately 150 mV peak-to-peak high-frequency noise on the PZT bias. As a result of this noise, which is made up of frequency components in the several-kHz range, too fast to be compensated by the 518 Hz locking dither, the effective lock point fluctuates with an amplitude of about one-fifth of the 90-MHz WGM linewidth. Fig. 3 shows a back-and-forth scan of 8 GHz with more uniform fiber transmission, illustrating the constancy of locked-mode power throughput that is achievable with our locking method.

Fig. 3. Another locked frequency scan at 1570 nm. The laser scans 8 GHz and returns. The vertical scale is the same as in Fig. 2. The baseline is at the frequency axis and again the locked transmission is about 80% of its off-resonance value. No mode hops are observed.

Another verification of the robustness of WGM locking and tracking is shown in Fig. 4. There, the PZT bias that keeps a WGM locked to the 1570-nm laser (New Focus, model 6328) is plotted as the tuning control signal applied to the laser’s frequency-modulation input is ramped up and down. This is again the 19 GHz tracking range shown in Fig. 2. Ideally, the WGM frequency would vary linearly with the tuner bias, and the laser frequency would vary linearly with the control voltage. However, the variation of laser frequency with control voltage shows hysteresis. Assuming the tuner PZT to be linear, the red curve in Fig. 4 is the bias predicted from the laser frequency tuning as observed with an optical spectrum analyzer. Comparison of the two curves in Fig. 4 shows that most of the hysteresis seen in the bias is actually hysteresis in the laser tuning, with only a small contribution from the nonlinearity of the compression tuner’s PZT. A mode jump would appear as a displacement of the bias curve by an amount on the order of ten times the noise level, and none are seen. The locking and tracking range shown in Figs. 2 and 4 is 19 GHz, but we were able to extend this to 30 GHz, the maximum scan range of the 1570-nm laser. Locking to the 830-nm laser worked equally well, and again the maximum tracking range was limited only by the laser’s frequency scan range of 40 GHz. At 830 nm the WGMs had, typically, Q≈5×106. Even under the environmentally noisy conditions that we used here, a WGM would remain locked to either laser for hours, with the laser scanning at rates of up to 2 GHz/s.

Fig. 4. Locked tuner PZT bias as it follows a 19-GHz frequency scan (and return) of the 1570-nm laser. Heavier (black) curve: PZT bias; no mode hops are observed. Lighter (red) curve: bias predicted from observed laser tuning hysteresis, assuming linear tuner PZT response.

Our results for WGM frequency tuning and locking are summarized in Table 1. Our compression tuner allows for tuning over a greater fraction of a free spectral range, and with faster response, than previously demonstrated [11

11. V. S. Ilchenko, P. S. Volikov, V. L. Velichansky, F. Treussart, V. Lefèvre-Seguin, J.-M. Raimond, and S. Haroche, “Strain-tunable high-Q optical microsphere resonator,” Opt. Commun. 145, 86–90 (1998). [CrossRef]

13

13. W. von Klitzing, R. Long, V. S. Ilchenko, J. Hare, and V. Lefèvre-Seguin, “Tunable whispering gallery modes for spectroscopy and CQED experiments,” http://arXiv.org/abs/quant-ph/0011102.

]. The ability to lock a high-Q WGM to a frequency-scanning laser will be useful for a number of potential applications of microsphere resonators. For example, the tracking range demonstrated is more than sufficient for doing wavelength-modulation spectroscopy in WGM evanescent-wave trace gas sensors. The maximum laser scan rate at which a WGM will remain locked, 2 GHz/s, is determined by the locking dither frequency and the Q value of the WGM. Locked scanning must be slow enough that the frequency change during one dither cycle is small compared to the WGM linewidth. To increase the maximum scan rate, it would be desirable to frequency-modulate the laser output to provide a faster locking dither. Then the locked scan rate would be limited only by the maximum compression tuning speed, which we found to be at least 16 GHz/ms. Thus locked modes of Q=2×106 could follow a scan nearly four orders of magnitude faster, or locked modes of Q≅1010 could be scanned at the present rate.

Table 1. Tuning ranges for a 550-µm diameter microsphere at two wavelengths

table-icon
View This Table

Acknowledgments

This work was supported by the Center for Sensors and Sensor Technologies, the Environmental Institute, the Oklahoma Center for the Advancement of Science and Technology, and by the National Science Foundation through an SBIR with Nomadics, Inc. We thank Reza Mofid, Sarah Bates, and Mike Lucas for assistance.

References and links

1.

V. B. Braginsky, M. L. Gorodetsky, and V. S. Ilchenko, “Quality factor and nonlinear properties of optical whispering-gallery modes,” Phys. Lett. A 137, 393–397 (1989). [CrossRef]

2.

D. W. Vernooy, V. S. Ilchenko, H. Mabuchi, E. W. Streed, and H. J. Kimble, “High-Q measurements of fused-silica microspheres in the near infrared,” Opt. Lett. 23, 247–249 (1998). [CrossRef]

3.

D. W. Vernooy, A. Furusawa, N. Ph. Georgiades, V. S. Ilchenko, and H. J. Kimble, “Cavity QED with high-Q whispering gallery modes,” Phys. Rev. A 57, R2293–R2296 (1998). [CrossRef]

4.

V. V. Vassiliev, V. L. Velichansky, V. S. Ilchenko, M. L. Gorodetsky, L. Hollberg, and A. V. Yarovitsky, “Narrow-line-width diode laser with a high-Q microsphere resonator,” Opt. Commun. 158, 305–312 (1998). [CrossRef]

5.

W. von Klitzing, E. Jahier, R. Long, F. Lissillour, V. Lefèvre-Seguin, J. Hare, J.-M. Raimond, and S. Haroche, “Very low threshold green lasing in microspheres by up-conversion of IR photons,” J. Opt. B: Quantum Semiclass. Opt. 2, 204–206 (2000). [CrossRef]

6.

M. Cai, O. Painter, K. J. Vahala, and P. C. Sercel, “Fiber-coupled microsphere laser,” Opt. Lett. 25, 1430–1432 (2000). [CrossRef]

7.

D. Braunstein, A. M. Khazanov, G. A. Koganov, and R. Shuker, “Lowering of threshold conditions for nonlinear effects in a microsphere,” Phys. Rev. A 53, 3565–3572 (1996). [CrossRef] [PubMed]

8.

A. T. Rosenberger, “Nonlinear Optical Effects in the Whispering-Gallery Modes of Microspheres,” in Operational Characteristics and Crystal Growth of Nonlinear Optical Materials, R. B. Lal and D. O. Frazier, eds., Proc. SPIE3793, 179–186 (1999).

9.

A. T. Rosenberger and J. P. Rezac, “Evanescent-wave sensor using microsphere whispering-gallery modes,” in Laser Resonators III, A. V. Kudryashov and A. H. Paxton, eds., Proc. SPIE3930, 186–192 (2000).

10.

I. H. Malitson, “Interspecimen Comparison of the Refractive Index of Fused Silica,” J. Opt. Soc. Am. 55, 1205–1209 (1965). [CrossRef]

11.

V. S. Ilchenko, P. S. Volikov, V. L. Velichansky, F. Treussart, V. Lefèvre-Seguin, J.-M. Raimond, and S. Haroche, “Strain-tunable high-Q optical microsphere resonator,” Opt. Commun. 145, 86–90 (1998). [CrossRef]

12.

W. von Klitzing, R. Long, V. S. Ilchenko, J. Hare, and V. Lefèvre-Seguin, “Frequency tuning of the whispering-gallery modes of silica microspheres for cavity quantum electrodynamics and spectroscopy,” Opt. Lett. 26, 166–168 (2001). [CrossRef]

13.

W. von Klitzing, R. Long, V. S. Ilchenko, J. Hare, and V. Lefèvre-Seguin, “Tunable whispering gallery modes for spectroscopy and CQED experiments,” http://arXiv.org/abs/quant-ph/0011102.

14.

J. C. Knight, G. Cheung, F. Jacques, and T. A. Birks, “Phase-matched excitation of whispering-gallery mode resonances by a fiber taper,” Opt. Lett. 22, 1129–1131 (1997). [CrossRef] [PubMed]

15.

M. Cai, O. Painter, and K. J. Vahala, “Observation of Critical Coupling in a Fiber Taper to a Silica-Microsphere Whispering-Gallery Mode System,” Phys. Rev. Lett. 85, 74–77 (2000). [CrossRef] [PubMed]

OCIS Codes
(060.2340) Fiber optics and optical communications : Fiber optics components
(140.4780) Lasers and laser optics : Optical resonators
(230.5750) Optical devices : Resonators

ToC Category:
Research Papers

History
Original Manuscript: March 21, 2001
Published: May 21, 2001

Citation
Jeromy Rezac and Albert Rosenberger, "Locking a microsphere whispering-gallery mode to a laser," Opt. Express 8, 605-610 (2001)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-8-11-605


Sort:  Journal  |  Reset  

References

  1. V. B. Braginsky, M. L. Gorodetsky, and V. S. Ilchenko, "Quality factor and nonlinear properties of optical whispering-gallery modes," Phys. Lett. A 137, 393-397 (1989). [CrossRef]
  2. D. W. Vernooy, V. S. Ilchenko, H. Mabuchi, E. W. Streed, and H. J. Kimble, "High-Q measurements of fused-silica microspheres in the near infrared," Opt. Lett. 23, 247-249 (1998). [CrossRef]
  3. D. W. Vernooy, A. Furusawa, N. Ph. Georgiades, V. S. Ilchenko, and H. J. Kimble, "Cavity QED with high-Q whispering gallery modes," Phys. Rev. A 57, R2293-R2296 (1998). [CrossRef]
  4. V. V. Vassiliev, V. L. Velichansky, V. S. Ilchenko, M. L. Gorodetsky, L. Hollberg, and A. V. Yarovitsky, "Narrow-line-width diode laser with a high-Q microsphere resonator," Opt. Commun. 158, 305-312 (1998). [CrossRef]
  5. W. von Klitzing, E. Jahier, R. Long, F. Lissillour, V. Lef�vre-Seguin, J. Hare, J.-M. Raimond, and S. Haroche, "Very low threshold green lasing in microspheres by up-conversion of IR photons," J. Opt. B: Quantum Semiclass. Opt. 2, 204-206 (2000). [CrossRef]
  6. M. Cai, O. Painter, K. J. Vahala, and P. C. Sercel, "Fiber-coupled microsphere laser," Opt. Lett. 25, 1430-1432 (2000). [CrossRef]
  7. D. Braunstein, A. M. Khazanov, G. A. Koganov, and R. Shuker, "Lowering of threshold conditions for nonlinear effects in a microsphere," Phys. Rev. A 53, 3565-3572 (1996). [CrossRef] [PubMed]
  8. A. T. Rosenberger, "Nonlinear Optical Effects in the Whispering-Gallery Modes of Microspheres," in Operational Characteristics and Crystal Growth of Nonlinear Optical Materials, R. B. Lal and D. O. Frazier, eds., Proc. SPIE 3793, 179-186 (1999).
  9. A. T. Rosenberger and J. P. Rezac, "Evanescent-wave sensor using microsphere whispering-gallery modes," in Laser Resonators III, A. V. Kudryashov and A. H. Paxton, eds., Proc. SPIE 3930, 186-192 (2000).
  10. I. H. Malitson, "Interspecimen Comparison of the Refractive Index of Fused Silica," J. Opt. Soc. Am. 55, 1205-1209 (1965). [CrossRef]
  11. V. S. Ilchenko, P. S. Volikov, V. L. Velichansky, F. Treussart, V. Lef�vre-Seguin, J.-M. Raimond, and S. Haroche, "Strain-tunable high-Q optical microsphere resonator," Opt. Commun. 145, 86-90 (1998). [CrossRef]
  12. W. von Klitzing, R. Long, V. S. Ilchenko, J. Hare, and V. Lef�vre-Seguin, "Frequency tuning of the whispering-gallery modes of silica microspheres for cavity quantum electrodynamics and spectroscopy," Opt. Lett. 26, 166-168 (2001). [CrossRef]
  13. W. von Klitzing, R. Long, V. S. Ilchenko, J. Hare, and V. Lef�vre-Seguin, "Tunable whispering gallery modes for spectroscopy and CQED experiments," http://arXiv.org/abs/quant-ph/0011102.
  14. J. C. Knight, G. Cheung, F. Jacques, and T. A. Birks, "Phase-matched excitation of whispering-gallery mode resonances by a fiber taper," Opt. Lett. 22, 1129-1131 (1997). [CrossRef] [PubMed]
  15. M. Cai, O. Painter, and K. J. Vahala, "Observation of Critical Coupling in a Fiber Taper to a Silica-.Microsphere Whispering-Gallery Mode System," Phys. Rev. Lett. 85, 74-77 (2000). [CrossRef] [PubMed]

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1. Fig. 2. Fig. 3.
 
Fig. 4.
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited