« journal navigation
A frequency-agile terahertz-wave parametric oscillator
Optics Express, Vol. 8, Issue 13, pp. 699-704 (2001)
http://dx.doi.org/10.1364/OE.8.000699
Acrobat PDF (167 KB)
Article Navigation
▸ Article Outline
– Abstract
1 Introduction
2 Experimental setup
3 Tuning properties
4 Summary
– References and links
– Abstract
1 Introduction
2 Experimental setup
3 Tuning properties
4 Summary
– References and links
Article Tools
Full Text
Article Info
References
Cited By
Figures
Metrics
Download PDF
Viewing Equations in the
HTML Article
Optimal Viewing Recommendations
Abstract
We demonstrated a pulse-to-pulse frequency-tunable LiNbO3 terahertz-wave parametric oscillator, pumped with a Q-switched Nd:YAG laser. Rapid tuning from 1 to 2 THz, with random frequency accessibility, was achieved by rotating the pump beam angle using an optical beam scanner and a telescope.
© Optical Society of America
[Optical Society of America ]
1 Introduction
The terahertz wave (THz-wave) region is spectroscopically significant, because it contains a large number of molecular rotation absorption lines. For example, terahertz time domain spectroscopy of propane-air flames has shown that panoramic terahertz absorption measurements provide complete flame characterization for determining species concentration and flame temperature [1]. In such analyses, frequency-agile THz-wave sources with continuous tunability over a broad spectral range are expected to improve the sensitivity, resolution, and speed of measurement. Although several tunable sources have been reported, such as free electron lasers [2], p-Ge lasers [3], and parametric oscillators, no source has yet achieved rapid frequency tuning over a wide tuning range.
R. A. Cheville and D. Grischkowsky. “Far-infrared terahertz time-domain spectroscopy of flames,” Opt. Lett. 20, 1646–1648 (1995) [CrossRef] [PubMed]
Susumu Komiyama. “Far-infrared emission from population-inverted hot-carrier system in p-Ge,” Phys. Rev. Lett. 48, 271–273 (1982) [CrossRef]
We studied a THz-wave parametric oscillator (TPO) using noncollinear phase matching in a LiNbO3 crystal pumped with a Q-switched Nd:YAG laser[4]. Despite its simplicity, the TPO was able to operate at room temperature, yet still provide a widely tunable (1~3 THz) THz-wave [5]. However, rapid frequency tuning was difficult to obtain using the conventional tuning method, because of the need to rotate the TPO cavity to vary the phase matching angle. In this paper, we describe a novel method of tuning a TPO using an optical beam scanner and a 1:1 telescope. This produced a TPO that was a frequency-agile THz-wave source over a broad spectral range.
K. Kawase, M. Sato, T. Taniuchi, and H. Ito. “Coherent tunable THz-wave generation from LiNbO3 with monolithic grating coupler,” Appl. Phys. Lett. 68, 2483–2485 (1996) [CrossRef]
2 Experimental setup
Fig. 1. Schematic of the 1.064 µm-pumped LiNbO3 frequency-agile TPO; FPI: Metal-mesh scanning Fabry-Perot interferometer, L1: f=1000 mm lens for pump beam focusing, L2, L3: f=200 mm lenses for the 1-to-1 telescope, PC: The computer used for scanner control, k
p
, k
T
, and k
i
: wave vectors for the pump, THz, and idler waves.
Asc hematic of the frequency-agile TPO is shown in Fig. 1. The pump laser was a Q-switched Nd:YAG laser that operated at a 50-Hz repetition rate; it had a maximum pulse energy of 36 mJ, and a 25-ns pulse duration. The pump beam was focused into the LiNbO3 crystal using a f=1000 mm lens (L1) to increase the power density. The pump diameter at L1 was 1 mm (FWHM), reduced to 0.5 mm at the input surface of the LiNbO3 crystal. In order to rotate the pump beam angle, the pump beam was reflected by a mirror on the optical beam scanner, which was a commercial device (HARMONIC DRIVE SYSTEMS Inc., LSA-20A-30) that provided a maximum angular deflection angle of ± 1.5 degrees. The scanner mirror rotated in proportion to the computer-controlled DC voltage, with a beam angular coefficient per voltage of 0.31 degrees/volt. The scanner had excellent linearity, and the angular deviation was less than 0.06 % per rotation angle. The response time of the beam scanner was 1 millisecond for a 1-degree step rotation at the optimum inertia. The image at the center of the scanner mirror was relayed onto the end of the LiNbO3 crystal of the TPO using a 1:1 telescope that consisted of two f=200 mm lenses, (L2, L3) with a lens interval of 400 mm. After passing through the telescope, the pump beam was injected into the TPO at the incidence angle, θIN
, provided by the optical beam scanner. Although the idler cavity axis was fixed in our experimental setup, we were able to vary the phase matching angle inside the crystal by rotating the pump beam. Compared with the conventional tuning method using idler cavity rotation, this method has advantages of speed and random wavelength accessibility. Asimila r tuning method was used in a mid-infrared periodically-poled LiNbO3 optical parametric oscillator that was developed as a lidar transmitter source [6], where kilohertz-repetition-rate pulse-to-pulse wavelength tuning was achieved using an acousto-optic beam deflector.
Steven T. Yang and Stephan P. Velsko. “Frequency-agile kilohertz repetition-rate optical parametric oscillator based on periodically poled lithium niobate,” Opt. Lett. 24, 133–135 (1999) [CrossRef]
The dimensions of the LiNbO3 crystal used in the TPO were 5×50×8 mm3 (z,x, y). Both facets of the crystal were polished and anti-reflection coated for operation at 1.064 µm. The y-surface of the crystal, where the Si-prisms are arrayed [7], was also polished, to reduce scattering of the pump and idler waves. Since the absorption coefficient of a LiNbO3 crystal in the THz-wave region is quite large, the pump beam was passed near the y-surface of the LiNbO3 crystal in order to minimize the THz-wave path inside the crystal, thereby reducing absorption loss. The crystal was placed inside a Fabry-Perot cavity that consisted of mirrors M1 and M2. M1 was highly reflective at 1.07 µm, while the reflectivity of M2 was 40 %. Only one-half of each mirror was coated, allowing the pump wave to pass through the other, uncoated half. The THz-wave exiting the LiNbO3 through the arrayed Si-prism coupler was detected with a 4K Si-bolometer.
Kodo Kawase, Junichi Shikata, Hiroaki Minamide, Kazuhiro Imai, and Hiromasa Ito. “Arrayed silicon prism coupler for a THz-wave parametric oscillator,” Appl. Opt. 40, 1423–1426 (2001) [CrossRef]
3 Tuning properties
Fig. 2. Measured output characteristics of the THz-wave (circles) and idler wave (triangles) from a LiNbO3 TPO at a fixed pump energy (20 mJ/pulse).
Figure 2 shows the measured tuning range of the THz-wave and idler wave from the frequency-agile TPO at a fixed pump energy of 20 mJ/pulse. The closed circles and open triangles are the THz-wave output and the idler-wave output, respectively. The scale for the THz-wave frequency is marked on the lower horizontal axis, and the corresponding scale for the idler wavelength is marked on the upper horizontal axis. We obtained tunability from 1 to 2 THz by varying the pump incidence angle from 0.9 to 1.85 degrees, respectively. The maximum THz-wave output was 150 pJ/pulse at 1.4 THz. Compared with the idler output, the THz-wave output decreased rapidly in the higher frequency region. The rapid decrease was due to the larger absorption loss inside the LiNbO3 crystal, which limited the upper frequency to ~2 THz. The incidence angle θIN
in the low frequency region was too small to completely separate the pump and idler beams at the input mirror, M1, and the small angle limited the lower frequency to ~1 THz. The decreased parametric gain and the small angle resulted in the oscillation threshold increase in the lower frequency region. The oscillation threshold at 1.5 THz was 14.5 mJ/pulse, and this increased to 16 mJ/pulse at 1.1 THz. We used an undoped LiNbO3 crystal in this experimental setup, since it was of better quality than our MgO-doped crystals. The tuning range can be extended to 2.6 THz using a MgO:LiNbO3 crystal, because a doped LiNbO3 crystal has a larger parametric gain than an undoped LiNbO3 crystal [8, 9]. The measured tuning characteristics were in good agreement with the theoretical curve, and showed that the pump incidence angle changed as expected. We also confirmed that measuring the THz wavelength or the idler wavelength at one incidence angle was sufficient to calibrate the THz wavelength of the frequency-agile TPO.
Jun-ichi Shikata, Ken-ichi Karino, Hiromasa Ito, and Kodo Kawase. “Tunable terahertz-wave generation from MgO:LiNbO3 optical parametric oscillator,” in Advanced Solid-state Lasers. OSA Trends in Optics and Photonics , Martin M. Fejer, Hagop Injeyan, and Ursula Keller, eds, Vol.26 of OSA Proceedings Series (Optical Society of America, Washington, D.C., 1999) pp. 481–486.
Fig. 3. Fabry-Perot scans of the THz-wave. The solid line shows the Fabry-Perot scan obtained with a pump incidence angle θIN
of 1.73 degrees. The wavelength was 167 µm. The dashed line shows the scan obtained with an angle of 1.49 degrees. The wavelength was 193 µm.
We measured the THz-wave linewidth and wavelength with a scanning Fabry-Perot interferometer consisting of a pair of Ni metal-mesh mirrors with a 65-µm grid. The measured finesse of the interferometer was approximately 10 for a mirror separation of several millimeters. Figure 3 shows examples of THz-wavelength measurements using the frequency-agile TPO. The solid and dashed lines show the Fabry-Perot scans for pump incidence angles θIN
of 1.73 and 1.49 degrees, respectively. The separation of the mirrors was increased from 36 to 436 µm. The horizontal axis shows the displacement of one of the metal-mesh mirrors, while the vertical axis is the intensity of the THz-wave transmitted. The separation between the neighboring peaks directly corresponds to half the THz wavelength. The measured wavelengths for 1.73 and 1.49 degrees were 167 and 193 µm, respectively. The spectral linewidths estimated from the Fabry-Perot traces were about 100 GHz, which is the typical THz-wave linewidth of a TPO without injection seeding. The linewidth can be dramatically reduced to its Fourier transform limit <200 MHz by narrow linewidth laser injection [10].
Kazuhiro Imai, Kodo Kawase, Jun ichi Shikata, Hiroaki Minamide, and Hiromasa Ito. “Injection-seeded terahertz-wave parametric oscillator,” Appl. Phys. Lett. 78, 1026–1028 (2001) [CrossRef]
Fig. 4. Pulse trains passed through a Fabry-Perot interferometer with a displacement of 49 µm. (a) The pump incidence angle, θIN
, was fixed at 1.73 degrees. (b) θIN
was fixed at 1.49 degrees. (c) θIN
was varied between 1.73 and 1.49 degrees with a 25-Hz square-wave signal to the optical scanner.
The displacement of the Fabry-Perot mirror was fixed at 49 µm in order to confirm fast frequency tuning and its repeatability. At the displacement in Fig. 3, the 167 µm-wave easily passed through the interferometer, while most of the 193-µm wave was blocked. The power ratio of the transmitted THz-waves at 167 and 193 µm was close to 4:1. Figures 4(a)~(c) show the transmitted THz-wave pulse train outputs detected by the 4K Si-bolometer. Figs.4 (a) and (b) show the pulse trains for fixed wavelengths of 167 and 193 µm, respectively. The amplitude of the transmitted THz-wave signal in Fig.4 (b) decreased to 0.1 according to the Fabry-Perot transmission. The THz-wave pulses in Figs.4 (a) and (b) arrived at the bolometer every 20 milliseconds, due to the 50-Hz repetition rate of the Nd:YAG laser operation. Fig.4(c) shows the pulse train when the THz wavelength was switched between 167 and 193 µm. The beam scanner was supplied with a 25-Hz square-wave signal in order to modulate the angle θIN
between 1.73 and 1.49 degrees. The pulse train consisted of both large and small amplitude pulses that alternately passed the Fabry-Perot interferometer. The amplitude ratio was nearly 3.6:1.
The interval of 40 milliseconds was due to the 25-Hz modulation of the THz wavelength. The repetition rate of the pump pulse limited the frequency agility in the present setup. However, since the response time for the optical beam scanner is 1 millisecond, it is possible to obtain kilohertz-repetition-rate pulse-to-pulse frequency tuning.
The conventional tuning method has the advantage of a fixed THz-wave beam direction, because the cavity rotation cancels the variation in the direction of the THz-wave beam[11]. The variation in the angle of the beam direction of the THz-wave exiting the Si prism remains large with the novel tuning method, because of the fixed idler cavity. When the THz-wave was extracted from the LiNbO3 crystal through an arrayed Si prism with a base angle of 53 degrees, the variation in the beam direction of the THz-wave of the frequency-agile TPO was about 2.8 degrees for the tuning range from 1 to 2 THz. The change in THz-wave beam direction should be canceled out as the level is normalized in spectroscopic measurement. The frequency-agile tunability of the novel tuning method is still useful for practical spectroscopic applications.
K. Kawase, M. Sato, K. Nakamura, T. Taniuchi, and H. Ito. “Unidirectional radiation of widely tunable THz wave using a prism coupler under noncollinear phase matching condition,” Appl. Phys. Lett. 71, 753–755 (1997) [CrossRef]
4 Summary
In summary, we experimentally demonstrated a pulse-to-pulse frequency- tunable THz-wave parametric oscillator based on a LiNbO3 crystal pumped with a Q-switch Nd:YAG laser. Rapid tuning from 1 to 2 THz with random frequency accessibility was achieved by rotating the pump beam angle using an optical beam scanner and a 1:1 telescope. Pulseto- pulse tuning between 167 and 193 µm was shown with a fixed-length Fabry-Perot interferometer used as a frequency- selective filter. The frequency agility of this THz-wave source makes it suitable for spectroscopic applications, such as the determination of species’ concentrations.
Acknowledgments
The authors thank Harmonic Drive Systems for supplying the optical beam scanner, Yamaju Ceramics Co., Ltd. for supplying LiNbO3 samples, and Mr. C. Takyu and Mr. T. Shoji, RIEC Tohoku University, for their excellent work in coating and polishing. This work was supported in part by a Grant-in Aid for Developmental Scientific Research (No. 13750318) from the Ministry of Education, Science, and Technology of Japan.
References and links
R. A. Cheville and D. Grischkowsky. “Far-infrared terahertz time-domain spectroscopy of flames,” Opt. Lett. 20, 1646–1648 (1995) [CrossRef] [PubMed] | |
Committee on Free Electron Lasers and National Research Council Other Advanced Coherent Light Sources, editors. Free Electron Lasers and Other Advanced source of Light, (National Academy Press, Washington, DC, 1994) pp. 24–31. | |
Susumu Komiyama. “Far-infrared emission from population-inverted hot-carrier system in p-Ge,” Phys. Rev. Lett. 48, 271–273 (1982) [CrossRef] | |
K. Kawase, M. Sato, T. Taniuchi, and H. Ito. “Coherent tunable THz-wave generation from LiNbO3 with monolithic grating coupler,” Appl. Phys. Lett. 68, 2483–2485 (1996) [CrossRef] | |
A. Morikawa, K. Kawase, J. Shikata, T. Taniuchi, and H. Ito. “Parametric THz-wave generation using trapezoidal LiNbO3 crystal,” In Terahertz Spectroscopy and Applications II , J. Martyn Chamberlain, ed., Proc. SPIE. 3828, 302–310 (1999) | |
Steven T. Yang and Stephan P. Velsko. “Frequency-agile kilohertz repetition-rate optical parametric oscillator based on periodically poled lithium niobate,” Opt. Lett. 24, 133–135 (1999) [CrossRef] | |
Kodo Kawase, Junichi Shikata, Hiroaki Minamide, Kazuhiro Imai, and Hiromasa Ito. “Arrayed silicon prism coupler for a THz-wave parametric oscillator,” Appl. Opt. 40, 1423–1426 (2001) [CrossRef] | |
Jun-ichi Shikata, Ken-ichi Karino, Hiromasa Ito, and Kodo Kawase. “Tunable terahertz-wave generation from MgO:LiNbO3 optical parametric oscillator,” in Advanced Solid-state Lasers. OSA Trends in Optics and Photonics , Martin M. Fejer, Hagop Injeyan, and Ursula Keller, eds, Vol.26 of OSA Proceedings Series (Optical Society of America, Washington, D.C., 1999) pp. 481–486. | |
H. Minamide, K. Kawase, K. Imai, A. Sato, and H. Ito. “Widely tunable MgO:LiNbO3 THz parametric oscillator and an application to THz spectroscopic system,” In Conference on Lasers and Electro-Optics , OSA Technical Digest, page 356, (Optical Society of America, Washington, D.C., 2000) | |
Kazuhiro Imai, Kodo Kawase, Jun ichi Shikata, Hiroaki Minamide, and Hiromasa Ito. “Injection-seeded terahertz-wave parametric oscillator,” Appl. Phys. Lett. 78, 1026–1028 (2001) [CrossRef] | |
K. Kawase, M. Sato, K. Nakamura, T. Taniuchi, and H. Ito. “Unidirectional radiation of widely tunable THz wave using a prism coupler under noncollinear phase matching condition,” Appl. Phys. Lett. 71, 753–755 (1997) [CrossRef] |
OCIS Codes
(190.2620) Nonlinear optics : Harmonic generation and mixing
(190.4410) Nonlinear optics : Nonlinear optics, parametric processes
(190.4970) Nonlinear optics : Parametric oscillators and amplifiers
(260.3090) Physical optics : Infrared, far
ToC Category:
Research Papers
History
Original Manuscript: May 30, 2001
Published: June 18, 2001
Citation
Kazuhiro Imai, Kodo Kawase, and Hiromasa Ito, "A frequency-agile terahertz-wave parametric oscillator," Opt. Express 8, 699-704 (2001)
http://www.opticsinfobase.org/oe/abstract.cfm?URI=oe-8-13-699
Sort: Journal | Reset
References
- R.A. Cheville and D. Grischkowsky. "Far-infrared terahertz time-domain spectroscopy of flames," Opt. Lett. 20, 1646-1648 (1995) [CrossRef] [PubMed]
- Committee on Free ElectronLasers and National ResearchCouncil Other Advanced Coherent LightSources, editors. Free Electron Lasers and Other Advanced source of Light, (National Academy Press, Washington, DC, 1994) pp. 24-31.
- Susumu Komiyama. "Far-infrared emission from population-inverted hot-carrier system in p-Ge," Phys. Rev. Lett. 48, 271-273 (1982) [CrossRef]
- K. Kawase, M. Sato, T. Taniuchi, and H. Ito. "Coherent tunable THz-wave generation from LiNbO3 with monolithic grating coupler," Appl. Phys. Lett. 68, 2483-2485 (1996) [CrossRef]
- A. Morikawa, K. Kawase, J. Shikata, T. Taniuchi, and H.Ito. "Parametric THz-wave generation using trapezoidal LiNbO3 crystal," In Terahertz Spectroscopy and Applications II, J. Martyn Chamberlain, ed., Proc. SPIE. 3828, 302-310 (1999)
- Steven T. Yang and Stephan P. Velsko. "Frequency-agile kilohertz repetition-rate optical parametric oscillator based on periodically poled lithium niobate," Opt. Lett. 24, 133-135 (1999) [CrossRef]
- Kodo Kawase, Junichi Shikata, Hiroaki Minamide, Kazuhiro Imai, and Hiromasa Ito. "Arrayed silicon prism coupler for a THz-wave parametric oscillator," Appl. Opt. 40, 1423-1426 (2001) [CrossRef]
- Jun-ichi Shikata, Ken-ichi Karino, Hiromasa Ito, and Kodo Kawase. "Tunable terahertz-wave generation from MgO:LiNbO3 optical parametric oscillator," in Advanced Solid-state Lasers. OSA Trends in Optics and Photonics, MartinM. Fejer, Hagop Injeyan, and Ursula Keller, eds, Vol. 26 of OSA Proceedings Series (Optical Society of America, Washington, D.C., 1999) pp. 481-486.
- H. Minamide, K. Kawase, K. Imai, A. Sato, and H. Ito. "Widely tunable MgO:LiNbO3 THz parametric oscillator and an application to THz spectroscopic system," In Conference on Lasers and Electro-Optics, OSA Technical Digest, page 356, (Optical Society of America, Washington, D.C., 2000)
- Kazuhiro Imai, Kodo Kawase, Jun ichi Shikata, Hiroaki Minamide, and Hiromasa Ito. "Injection-seeded terahertz-wave parametric oscillator," Appl. Phys. Lett. 78, 1026-1028 (2001) [CrossRef]
- K. Kawase, M.S ato, K. Nakamura, T. Taniuchi, and H. Ito. "Unidirectional radiation of widely tunable THz wave using a prism coupler under noncollinear phase matching condition," Appl. Phys. Lett. 71, 753-755 (1997) [CrossRef]
Cited By |
 Alert me when this paper is cited |
OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.
« Previous Article | Next Article »
OSA is a member of 