OSA's Digital Library

Optics Letters

Optics Letters

| RAPID, SHORT PUBLICATIONS ON THE LATEST IN OPTICAL DISCOVERIES

  • Editor: Alan E. Willner
  • Vol. 33, Iss. 2 — Jan. 15, 2008
  • pp: 134–136
« Show journal navigation

Creating vortex retarders using photoaligned liquid crystal polymers

Scott C. McEldowney, David M. Shemo, Russell A. Chipman, and Paula K. Smith  »View Author Affiliations


Optics Letters, Vol. 33, Issue 2, pp. 134-136 (2008)
http://dx.doi.org/10.1364/OL.33.000134


View Full Text Article

Acrobat PDF (266 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We present developments using photoaligned liquid crystal polymers for creating vortex retarders, half-wave retarders with a continuously variable fast axis. Polarization properties of components designed to create different polarization vortex modes are presented. We assess the viability of these components by using the theoretical and experimental point spread functions in Mueller matrix format, or a point spread matrix (PSM). The measured PSM of these components in an optical system is very close to the theoretically predicted values, thus showing that these components should provide excellent performance in applications utilizing polarized optical vortices.

© 2008 Optical Society of America

Optical fields that are linearly polarized and axially symmetric are becoming very important in the design of advanced optical systems. In the case of radially or azimuthally polarized beams, they have been shown to improve performance in confocal microscopy [1

1. R. Dorn, S. Quabis, and G. Leuchs, Phys. Rev. Lett. 91, 233901 (2003). [CrossRef] [PubMed]

] and lithography systems [2

2. X. Grosjean, D. Courjon, and C. Bainier, Opt. Lett. 32, 976 (2007). [CrossRef] [PubMed]

]. More general polarization vortices of single or higher orders can be used to create nondiffracting or Bessel fields [3

3. A. Niv, G. Biener, V. Kleiner, and E. Hasmin, Opt. Lett. 29, 238 (2004). [CrossRef] [PubMed]

]. One emerging application of Bessel beams is in enlarging the particle trapping region of optical tweezers [4

4. D. McGloin and K. Dholakia, OE Mag. January, 2003, pp. 42–45.

].

Traditionally, these fields are made by using coherent interference of TE and TM modes [5

5. S. C. Tidwell, D. H. Ford, and W. D. Kimura, Appl. Opt. 29, 2234 (1990). [CrossRef] [PubMed]

]. Recently, components that utilize a constant retardance but variable fast axis have demonstrated the potential of monolithic components to create such vortex fields [2

2. X. Grosjean, D. Courjon, and C. Bainier, Opt. Lett. 32, 976 (2007). [CrossRef] [PubMed]

, 6

6. M. Stalder and M. Schadt, Opt. Lett. 21, 1948 (1996). [CrossRef] [PubMed]

, 7

7. G. Machavariani, Y. Lumer, I. Moshe, A. Meir, and S. Jackel, Opt. Lett. 32, 1468 (2007). [CrossRef] [PubMed]

]. We define a vortex retarder as a monolithic component that has a constant retardance but a fast axis that rotates about a point. A plurality of crystals can be assembled to make a vortex retarder [7

7. G. Machavariani, Y. Lumer, I. Moshe, A. Meir, and S. Jackel, Opt. Lett. 32, 1468 (2007). [CrossRef] [PubMed]

]. However, the fast axis cannot be made continuous, therefore causing diffraction at the boundaries of the different crystals forcing the use of additional components to create a pure polarization vortex. The assembly process is also complex, making the components expensive. Vortex retarders made from nanostructures [3

3. A. Niv, G. Biener, V. Kleiner, and E. Hasmin, Opt. Lett. 29, 238 (2004). [CrossRef] [PubMed]

] have the potential to create stable retarders with a continuous fast axis and, in principle, can be made over broad wavelength ranges. However, the feature sizes required for making visible vortex retarders is beyond state-of-the-art of feature generation and thus has been demonstrated only at infrared wavelengths. Vortex retarders made by using twisted nematic liquid crystal [6

6. M. Stalder and M. Schadt, Opt. Lett. 21, 1948 (1996). [CrossRef] [PubMed]

] are limited in that, thus far, multiple components are required if polarization vortices beyond order 2 are required.

Liquid crystal polymers (LCPs) are materials that combine the birefringent properties of liquid crystals with the mechanical properties of polymers. The orientation of a LCP is achieved through the use of an alignment layer [8

8. M. Schadt, H. Seiberle, A. Schuster, and S. M. Kelly, Jpn. J. Appl. Phys., Part 1 34, L764 (1995). [CrossRef]

]. Photoalignment is a recent advancement that enables noncontact alignment, which produces high-quality alignment with low defects as compared with rubbing alignment techniques [8

8. M. Schadt, H. Seiberle, A. Schuster, and S. M. Kelly, Jpn. J. Appl. Phys., Part 1 34, L764 (1995). [CrossRef]

]. Photoalignment also allows a high degree of customization in producing birefringent components. Once the alignment orientation has been established in the alignment layer, the LCP precursor is applied and cross-linked to make its orientation permanent.

In this Letter, we describe the development of a vortex retarder using a photo-aligned LCP. We demonstrate vortex retarders, half-wave retarders with a continuously varying fast axis, creating m=1, 2, 3 vortex modes at 550nm. We analyzed these elements both theoretically and experimentally by measuring the space variant Mueller matrix of each component. The viability of these components is assessed by determining the Mueller matrix of the point spread function (PSF) or point spread matrix (PSM); the combination of these allows us to fully understand the optical vortex created by the component and its impact in an optical system. The PSM is a Mueller matrix for which each element of the matrix is a PSF.

The samples were fabricated on 2in. (1in.=2.54cm) squares of Corning 1737F glass, having a broadband visible antireflection coating on the back surface. The process targeted a half-wave retardance for wavelengths in the range of 540550nm. A photoalignment layer (ROP108 from Rolic) was spin coated onto the substrate and baked, and then the alignment was set through exposure to linear polarized UV light. We exposed the alignment layer through a narrow wedge-shaped aperture located between the substrate and the polarizer. Both the polarizer and the substrate were continuously rotated during the exposure process to create a continuous variation in photoalignment orientation with respect to azimuthal locations on the substrate. The desired α slopes in Eq. (1) were determined by the relative rotation speeds. The LCP precursor (ROF5104 from Rolic) was then spin coated and subsequently polymerized by using a UV curing processes. The orientation of the LCP is set by the orientation of the alignment layer. The retardance value depends on the thickness of LCP.

Examining the three samples in white light between crossed polarizers produces the results shown in Fig. 1. Figure 1 clearly shows the modulation of intensity expected. The number of modulations is as expected for each component, with m=1 having 2 modulations, m=2 having 4, and m=3 having 6.

The samples were mapped using a Mueller matrix polarimeter from Axometrics at a 1mm pitch in an xy map. The retardance and fast axis maps are shown in Fig. 2 for the m=1, 2, 3 vortex retarders. The irregularities seen at the top, bottom, left, and right of the retardance and fast axis maps are merely artifacts of the retardance order changing from order 0 to order 1 where the LCP becomes thicker near the substrate edge. (The retardance map analysis here assumes order 0 for all locations.) Although a few minor coating artifacts are present in the retardance maps, the samples show excellent retardance uniformity (nonuniformity less than 2.5%); the fast axis is continuous at the scale that the parts were mapped.

To determine the effectiveness of these vortex retarders, we measured the PSM and compared this with calculated values. To calculate the PSM in the case of a paraxial system, we followed the technique of McGuire and Chipman [9

9. J. P. McGuire Jr. and R. A. Chipman, J. Opt. Soc. Am. A 7, 1614 (1990). [CrossRef]

]. The amplitude response matrix (h) for a polarizing system containing a single or group of lenses is determined by taking the Fourier transform of the Jones matrix of the vortex retarder and multiplying by a quadratic phase factor between the object and the image.

To covert the amplitude response matrix to the PSM, we use the relationship
P=hh*,
(3)
where ⊗ indicates the direct product [9

9. J. P. McGuire Jr. and R. A. Chipman, J. Opt. Soc. Am. A 7, 1614 (1990). [CrossRef]

]. To convert to the Stokes basis, we use the transformation
Ps=SPS1
(4)
where S is a transformation matrix [9

9. J. P. McGuire Jr. and R. A. Chipman, J. Opt. Soc. Am. A 7, 1614 (1990). [CrossRef]

].

To measure the PSM, we used a Mueller matrix imaging polarimeter [10

10. J. L. Pezzaniti and R. A. Chipman, Opt. Eng. 34, 155 (1995).

] and set the CCD camera image plane conjugate to fiber optic illumination. The measurements were made at 550nm where the vortex retarders were approximately a half-wave. The vortex retarder was uniformly illuminated over a diameter of approximately 2.5mm.

Figure 3 shows the calculated and the measured PSM for the three vortex retarders. The results show very good qualitative agreement between the measured PSM and the calculated PSM. The only exception is the higher than predicted value in the m03 and m30 elements of the PSM. Further analysis suggests that this is partially due to the center area (<100μm) of the vortex retarder where the orientation becomes disordered. The impact of these elements is to increase the circular polarization and circular polarizance of the component.

With the PSM measured, it was trivial to determine the field generated at the image plane for a variety of input polarization states and output analyzers. As an example, Fig. 4 shows the intensity at the image plane for each of the vortex retarders for three conditions based on the measured PSM; arbitrary input with arbitrary output, horizontal linear polarized input with horizontal linear polarized output, and horizontal linear polarized input with vertical polarized output.

The PSFs shown in Figs. 4a, 4d, 4g show the expected doughnut-shaped profile. The PSF function measured when an analyzer is used shows a propeller-shaped profile with the rotation of the propeller depending on the order of the vortex retarder.

In conclusion, we have demonstrated that we can make vortex retarders for visible wavelengths by using photoaligned LCP materials. The fast axis can be made continuous such that vortex retarders of single or multiple modes can be manufactured. The measured PSM of these components in an optical system is very close to the theoretically predicted values, thus showing that these components should provide excellent performance in applications utilizing polarized optical vortices.

Fig. 1 Vortex retarders of m=1, 2, 3 analyzed through a linear polarizer.
Fig. 2 Retardance (left) and fast axis (right) for (a) the m=1 component, (b) the m=2 component, and (c) the m=3 component. In all cases the retardance is measured in degrees at λ=570, and the fast axis is in degrees.
Fig. 3 (a)–(c) Calculated PSM and (d)–(f) Measured PSM for the m=1, 2, 3 vortex retarders.
Fig. 4 (a) Irradiance of the (a) m=1, (d) m=2, and (g) m=3 vortex retarder measured intensity; (b), (e), (h), corresponding HLP input and HLP analyzer; (c), (f), (i) with HLP input and VLP analyzer.
1.

R. Dorn, S. Quabis, and G. Leuchs, Phys. Rev. Lett. 91, 233901 (2003). [CrossRef] [PubMed]

2.

X. Grosjean, D. Courjon, and C. Bainier, Opt. Lett. 32, 976 (2007). [CrossRef] [PubMed]

3.

A. Niv, G. Biener, V. Kleiner, and E. Hasmin, Opt. Lett. 29, 238 (2004). [CrossRef] [PubMed]

4.

D. McGloin and K. Dholakia, OE Mag. January, 2003, pp. 42–45.

5.

S. C. Tidwell, D. H. Ford, and W. D. Kimura, Appl. Opt. 29, 2234 (1990). [CrossRef] [PubMed]

6.

M. Stalder and M. Schadt, Opt. Lett. 21, 1948 (1996). [CrossRef] [PubMed]

7.

G. Machavariani, Y. Lumer, I. Moshe, A. Meir, and S. Jackel, Opt. Lett. 32, 1468 (2007). [CrossRef] [PubMed]

8.

M. Schadt, H. Seiberle, A. Schuster, and S. M. Kelly, Jpn. J. Appl. Phys., Part 1 34, L764 (1995). [CrossRef]

9.

J. P. McGuire Jr. and R. A. Chipman, J. Opt. Soc. Am. A 7, 1614 (1990). [CrossRef]

10.

J. L. Pezzaniti and R. A. Chipman, Opt. Eng. 34, 155 (1995).

OCIS Codes
(230.0230) Optical devices : Optical devices
(230.3720) Optical devices : Liquid-crystal devices
(230.5440) Optical devices : Polarization-selective devices

ToC Category:
Optical Devices

History
Original Manuscript: October 22, 2007
Revised Manuscript: December 5, 2007
Manuscript Accepted: December 5, 2007
Published: January 9, 2008

Citation
Scott C. McEldowney, David M. Shemo, Russell A. Chipman, and Paula K. Smith, "Creating vortex retarders using photoaligned liquid crystal polymers," Opt. Lett. 33, 134-136 (2008)
http://www.opticsinfobase.org/ol/abstract.cfm?URI=ol-33-2-134


Sort:  Year  |  Journal  |  Reset  

References

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.

Figures

Fig. 1 Fig. 2 Fig. 3
 
Fig. 4
 

« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited