OSA's Digital Library

Optics Letters

Optics Letters

| RAPID, SHORT PUBLICATIONS ON THE LATEST IN OPTICAL DISCOVERIES

  • Editor: Xi-Cheng Zhang
  • Vol. 39, Iss. 12 — Jun. 15, 2014
  • pp: 3650–3653
« Show journal navigation

Wideband thulium–holmium-doped fiber source with combined forward and backward amplified spontaneous emission at 1600–2300  nm spectral band

Pavel Honzatko, Yauhen Baravets, Ivan Kasik, and Ondrej Podrazky  »View Author Affiliations


Optics Letters, Vol. 39, Issue 12, pp. 3650-3653 (2014)
http://dx.doi.org/10.1364/OL.39.003650


View Full Text Article

Acrobat PDF (657 KB)





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

We have experimentally demonstrated two extremely wideband amplified spontaneous emission (ASE) sources. High bandwidth is achieved by combining the backward and forward ASEs generated in thulium–holmium-doped fiber using appropriate wideband couplers. The ASE source optimized for flat spectral power density covers a spectral range from 1527 to 2171 nm at a 10dB level. The ASE source optimized for spectroscopy features an enhancement with respect to single-mode fiber (SMF) coupled halogen lamps within the spectral range from 1540 nm to more than 2340 nm covering the 800 nm bandwidth.

© 2014 Optical Society of America

Wideband fiber amplified spontaneous emission (ASE) sources are needed for the manufacturing and characterization of fiber components, optical metrology, fiber sensors, spectroscopy, and medical imaging, including optical coherence tomography. They are expected to provide spectral power density of several orders of magnitude higher than halogen bulb sources coupled into a single-mode fiber. Commercially available sources usually have a bandwidth of lower than 50 nm around 1050 nm, 50–100 nm around 1570 nm, and 100 nm around 1900 nm. Wideband sources based on supercontinuum generation can cover a much wider region. Wang presented a supercontinuum fiber source covering the spectrum from 1800 nm up to 2700 nm [1

1. J. Geng, Q. Wang, and S. Jiang, Proc. SPIE 8237, 82370R (2012).

]. The commercially available supercontinuum source from NKT Photonics covers a spectral band of 450–2400 nm. While supercontinuum wideband sources have numerous attractive features, their cost makes them prohibitive for many applications.

We will concentrate on ASE sources for 2000 nm band in this Letter. Attractiveness of the ASE sources is based on their low cost and their capability to provide a stable unpolarized wideband signal with a white rf-spectrum. The ASE sources for 2000 nm band are mostly based on thulium- and holmium-doped fibers. The ASE was observed in a thulium-doped fiber for the first time to our knowledge by Oh et al. [2

2. K. Oh, A. Kilian, P. M. Weber, L. Reinhart, Q. Zhang, and T. F. Morse, Opt. Lett. 19, 1131 (1994). [CrossRef]

]. The silica fiber with a multicomponent glass core was core-pumped with a titan–sapphire laser, and ASE with a bandwidth of 77 nm centered around 1900 nm was observed. It was recognized that thulium-doped fibers have the broadest emission bandwidth of all rare-earth doped fibers [3

3. S. D. Jackson, Nat. Photonics 6, 423 (2012). [CrossRef]

]. Wide gain bandwidth was used for wideband amplification [4

4. Z. Li, A. M. Heidt, N. Simakov, Y. Jung, J. M. O. Daniel, S. U. Alam, and D. J. Richardson, Opt. Express 21, 26450 (2013).

,5

5. Z. Li, A. M. Heidt, J. M. O. Daniel, Y. Jung, S. U. Alam, and D. J. Richardson, Opt. Lett. 21, 9289 (2013).

] and widely tunable lasers [6

6. T. S. McComb, R. A. Sims, C. C. C. Willis, P. Kadwani, V. Sudesh, L. Shah, and M. Richardson, Appl. Opt. 49, 6236 (2010). [CrossRef]

]. Halder et al. reported on a bismuth–thulium-doped fiber ASE generator covering a spectral range of 1800–2050 nm [7

7. A. Halder, M. C. Paul, S. W. Harun, S. M. M. Ali, N. Saidin, S. S. A. Damanhuri, H. Ahmad, S. Das, M. Pal, and S. K. Bhadra, IEEE Photon. J. 4, 2176 (2012). [CrossRef]

].

Holmium codoping of thulium-doped fibers is used to extend the emission to longer wavelengths. The Tm:Ho-doped double-clad ZBLAN fiber pumped at a wavelength of 803 nm was used to generate ASE with a total spectral width of 380 nm peaked at a wavelength of 2065 nm and a power of about 2 mW [8

8. Y. H. Tsang, T. A. King, K. Ko, and J. Lee, J. Mod. Opt. 53, 991 (2006). [CrossRef]

]. Bandwidth narrowing was observed for higher pump powers. Dorosz achieved an ASE bandwidth of 63 nm in thulium–holmium-doped fibers [9

9. D. Dorosz, J. Zmojda, M. Kochanowicz, P. Miluski, and J. Dorosz, Acta Phys. Pol. A 122, 927 (2012).

]. The emission of thulium-doped fibers can be also reduced to a shorter wavelength using the erbium as the codopant. Luminescence emission with a bandwidth of 420 nm was observed in antimony-germanate glasses codoped with Er3+/Tm3+ ions [10

10. D. Dorosz, J. Zmojda, and M. Kochanowicz, Opt. Eng. 53, 071807 (2014). [CrossRef]

].

ASE sources based on large-mode area of double-clad fibers were proven to be suitable as high-power wideband sources. High-power and wideband sources are generally required in fiber optic gyroscopes, optical coherence tomography, etc. Tm-doped silica fiber cladding-pumped by a diode laser at 803 nm was reported to generate 88 mW with a spectral bandwidth of up to 42 nm centered at 2005 nm [8

8. Y. H. Tsang, T. A. King, K. Ko, and J. Lee, J. Mod. Opt. 53, 991 (2006). [CrossRef]

]. A short piece of the highly thulium-doped tungsten tellurite double-clad fiber pumped by a 792 nm laser diode was used to generate 34 mW ASE with a bandwidth up to 140 nm around 2000 nm [11

11. P.-W. Kuan, K. Li, G. Zhang, X. Wang, L. Zhang, G. Bai, Y. Tsang, and L. Hu, Opt. Mater. Express 3, 723 (2013). [CrossRef]

]. Halder et al. presented the ASE source based on the double-clad ytterbium-sensitized thulium-doped fiber with an integrated power of 1 W and a 10 dB bandwidth of 330 nm covering the spectrum from 1770 to 2100 nm [12

12. A. Halder, M. Paul, N. S. Shahabuddin, S. Harun, N. Saidin, S. S. A. Damanhuri, H. Ahmad, S. Das, M. Pal, and S. Bhadra, IEEE Photon. J. 4, 14 (2012). [CrossRef]

]. Large-mode-area double-clad fiber was used to generate 8 mW of power over a bandwidth of 280 nm that was narrowed to 36 nm when the output power achieved 11 W [13

13. D. Y. Shen, L. Pearson, P. Wang, J. K. Sahu, and W. A. Clarkson, Opt. Express 16, 11021 (2008). [CrossRef]

]. The fiber was pumped by beam-shaped 790 nm diode bars from both ends.

In this Letter, we describe a low-cost solution made from a core-pumped thulium–holmium-doped fiber and a pair of wideband fused fiber couplers that spectrally combine forward and backward ASE. Extremely wideband operation is achieved in this way covering more than 645 nm at a level of 10dB. Figure 1 illustrates the experimental setup of the ASE source. The ASE source includes a thulium–holmium-doped fiber as an active medium. The fiber was fabricated in our laboratories from a preform prepared by modified chemical vapor deposition (MCVD) and solution doping as described elsewhere [14

14. P. Honzatko, A. Dhar, I. Kasik, O. Podrazky, V. Matejec, P. Peterka, W. Blanc, and B. Dussardier, Proc. SPIE 8306, 830608 (2011).

]. The fiber has a numerical aperture of 0.15 and a core diameter of 8 μm. The alumina-rich silica core is doped with 1800 ppm of thulium and 360 ppm of holmium. The spectral absorption of the fiber is shown in Fig. 2. The thulium absorption peak achieves 56dB/m at a wavelength of 1642 nm. The active fiber was pumped by an amplified CW laser working in a wavelength range of 1571–1611 nm. This corresponds to a left wing of absorption peak corresponding to the H63F43 transition of thulium ions. The F43+I85H63+I75 energy transfer process between the thulium and holmium ions then populates the excited state of Ho3+ [9

9. D. Dorosz, J. Zmojda, M. Kochanowicz, P. Miluski, and J. Dorosz, Acta Phys. Pol. A 122, 927 (2012).

]. The pump wavelength should be selected with respect to a trade-off between the thulium absorption and an efficiency of the booster amplifier that is based on erbium-doped fiber.

Fig. 1. Experimental scheme of the ASE source. DFBL—distributed feedback laser, BA—L-band booster amplifier, THDF—thulium–holmium-doped fiber, C1,2—couplers, MP—measurement point (cf. text).
Fig. 2. Spectral absorption of the thulium–holmium doped fiber used in the experiments.

We used 320 cm of the active fiber in the ASE source as a compromise between the requirements to completely absorb the strong pump and to achieve maximum magnitude of the forward ASE. We needed fiber sufficiently long enough to absorb almost all the pump and prevent damage to the sensitive detector of the spectrometer. On the other hand, fiber that is too long reabsorbs ASE at short wavelengths while ASE is not augmented anymore at long wavelengths. We combined the backward and forward ASEs in order to build an ultrawideband ASE source as illustrated in Fig 1. The backward ASE is much stronger than the forward ASE. The forward ASE is pronouncedly shifted toward the longer wavelengths as a result of reabsorption of the ASE along the fiber [4

4. Z. Li, A. M. Heidt, N. Simakov, Y. Jung, J. M. O. Daniel, S. U. Alam, and D. J. Richardson, Opt. Express 21, 26450 (2013).

]. We tried standard communication coarse wavelength-division multiplexers to couple the pump into the active fiber and to get the backward ASE out. Unfortunately, these multiplexers have a lot of spectral transmission dips above 2000 nm. We finally sacrificed some of the pump power and used a wideband fused coupler instead. The coupling strength of fused biconical taper couplers depends on the overlap of modes of tapered fibers and therefore it is wavelength dependent [15

15. K. Jedrzejewski, Opto-Electron. Rev. 8, 153 (2000).

]. We selected the coupler with a 50% coupling ratio at 1600 nm. The source was pumped at a wavelength of 1611 nm with a power of 480 mW. The spectral transmission of the coupler for backward ASE decreases toward the longer wavelengths and compensates the positive slope of backward ASE until its peak is achieved. After this point a dip in the output spectrum appears that is ultimately compensated by forward ASE. This allows us to achieve relatively flat ASE spectrum at the output of the source. Both the couplers used in the source were selected from standard commercial products designed for telecommunication applications based on their measured spectral transmission functions (Fig. 3). The solid blue curve shows the transmission in the backward ASE branch (ports 13), while the solid red curve shows the transmission in the pump branch (ports 21). ASE in various points of the setup can be seen in Fig. 4. The blue curve shows the forward ASE transmitted over the output coupler. It was measured with fibers disconnected in the measurement point MP (Fig. 1). The dip at 1950 nm caused by the absorption of the holmium ions is clearly visible and can be attributed to transition I85I75. The emission extends far beyond 2300 nm. Such emission cannot be observed in fibers doped solely with thulium. The green curve shows the backward ASE transmitted over the first coupler that was measured in measurement point MP. The pump peak visible at 1611 nm results from a reflection at the unused port of the first coupler that was equipped with an angle polished connector (APC). While the reflection is greatly suppressed by the APC connector, it was still necessary to make several tight loops at this idle pigtail to further suppress the backreflection. Finally, combined forward and backward ASE were measured for the closed backward ASE path, as represented by the magenta curve in Fig. 4. As can be seen, the backward ASE is further attenuated by the second coupler. The forward ASE branch of the second coupler should extend to the furthest wavelengths possible. Its transmission function is shown by the dashed lines in Fig. 3. In this way a relatively flat output spectrum can be achieved. In Fig. 5, the output spectrum is labeled with the achieved bandwidths to demonstrate the efficiency of this method. Looking at the 3 dB bandwidth it should be kept in mind that the ripple is much larger than 3 dB. Bandwidths achieved 645 nm at the level of 10dB and 807 nm at 20dB.

Fig. 3. Transmission functions of coupler C1 (solid) and C2 (dashed). Blue shows the transmission functions for backward ASE path.
Fig. 4. Backward ASE (green), forward ASE (blue), and combined ASE (magenta) measured for the spectrally flat ASE source.
Fig. 5. Combined spectrum of the ASE source.

Fig. 6. Backward ASE (green), forward ASE (blue), and combined ASE (magenta) measured for the ASE source optimized for spectroscopy.
Fig. 7. Enhancement factor with respect to a SMF28 fiber coupled halogen source for the spectrally flat ASE source (blue) and for the source optimized for spectroscopy (magenta).

In conclusion, we have developed the spectrally flat ASE source with 10dB bandwidth of 645 nm with an integrated power of approximately 1.3 μW. We believe that it is the widest bandwidth achieved in rare-earth-doped fiber based ASE sources to date. To achieve such a bandwidth, we combined the forward and backward ASEs generated in a thulium–holmium-doped optical fiber using wideband fused fiber couplers. We also optimized this source for spectroscopy. It has an integrated power of 9 μW and covers a spectral band of more than 800 nm.

We gratefully acknowledge funding of this work by the Czech Science Foundation under Grant Nos. P205-11-1840 and 14-35256S.

References

1.

J. Geng, Q. Wang, and S. Jiang, Proc. SPIE 8237, 82370R (2012).

2.

K. Oh, A. Kilian, P. M. Weber, L. Reinhart, Q. Zhang, and T. F. Morse, Opt. Lett. 19, 1131 (1994). [CrossRef]

3.

S. D. Jackson, Nat. Photonics 6, 423 (2012). [CrossRef]

4.

Z. Li, A. M. Heidt, N. Simakov, Y. Jung, J. M. O. Daniel, S. U. Alam, and D. J. Richardson, Opt. Express 21, 26450 (2013).

5.

Z. Li, A. M. Heidt, J. M. O. Daniel, Y. Jung, S. U. Alam, and D. J. Richardson, Opt. Lett. 21, 9289 (2013).

6.

T. S. McComb, R. A. Sims, C. C. C. Willis, P. Kadwani, V. Sudesh, L. Shah, and M. Richardson, Appl. Opt. 49, 6236 (2010). [CrossRef]

7.

A. Halder, M. C. Paul, S. W. Harun, S. M. M. Ali, N. Saidin, S. S. A. Damanhuri, H. Ahmad, S. Das, M. Pal, and S. K. Bhadra, IEEE Photon. J. 4, 2176 (2012). [CrossRef]

8.

Y. H. Tsang, T. A. King, K. Ko, and J. Lee, J. Mod. Opt. 53, 991 (2006). [CrossRef]

9.

D. Dorosz, J. Zmojda, M. Kochanowicz, P. Miluski, and J. Dorosz, Acta Phys. Pol. A 122, 927 (2012).

10.

D. Dorosz, J. Zmojda, and M. Kochanowicz, Opt. Eng. 53, 071807 (2014). [CrossRef]

11.

P.-W. Kuan, K. Li, G. Zhang, X. Wang, L. Zhang, G. Bai, Y. Tsang, and L. Hu, Opt. Mater. Express 3, 723 (2013). [CrossRef]

12.

A. Halder, M. Paul, N. S. Shahabuddin, S. Harun, N. Saidin, S. S. A. Damanhuri, H. Ahmad, S. Das, M. Pal, and S. Bhadra, IEEE Photon. J. 4, 14 (2012). [CrossRef]

13.

D. Y. Shen, L. Pearson, P. Wang, J. K. Sahu, and W. A. Clarkson, Opt. Express 16, 11021 (2008). [CrossRef]

14.

P. Honzatko, A. Dhar, I. Kasik, O. Podrazky, V. Matejec, P. Peterka, W. Blanc, and B. Dussardier, Proc. SPIE 8306, 830608 (2011).

15.

K. Jedrzejewski, Opto-Electron. Rev. 8, 153 (2000).

OCIS Codes
(060.2270) Fiber optics and optical communications : Fiber characterization
(060.2280) Fiber optics and optical communications : Fiber design and fabrication
(060.2380) Fiber optics and optical communications : Fiber optics sources and detectors
(140.6630) Lasers and laser optics : Superradiance, superfluorescence
(230.2285) Optical devices : Fiber devices and optical amplifiers

ToC Category:
Fiber Optics and Optical Communications

History
Original Manuscript: April 14, 2014
Revised Manuscript: April 29, 2014
Manuscript Accepted: May 6, 2014
Published: June 12, 2014

Citation
Pavel Honzatko, Yauhen Baravets, Ivan Kasik, and Ondrej Podrazky, "Wideband thulium–holmium-doped fiber source with combined forward and backward amplified spontaneous emission at 1600–2300  nm spectral band," Opt. Lett. 39, 3650-3653 (2014)
http://www.opticsinfobase.org/ol/abstract.cfm?URI=ol-39-12-3650


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. J. Geng, Q. Wang, and S. Jiang, Proc. SPIE 8237, 82370R (2012).
  2. K. Oh, A. Kilian, P. M. Weber, L. Reinhart, Q. Zhang, and T. F. Morse, Opt. Lett. 19, 1131 (1994). [CrossRef]
  3. S. D. Jackson, Nat. Photonics 6, 423 (2012). [CrossRef]
  4. Z. Li, A. M. Heidt, N. Simakov, Y. Jung, J. M. O. Daniel, S. U. Alam, and D. J. Richardson, Opt. Express 21, 26450 (2013).
  5. Z. Li, A. M. Heidt, J. M. O. Daniel, Y. Jung, S. U. Alam, and D. J. Richardson, Opt. Lett. 21, 9289 (2013).
  6. T. S. McComb, R. A. Sims, C. C. C. Willis, P. Kadwani, V. Sudesh, L. Shah, and M. Richardson, Appl. Opt. 49, 6236 (2010). [CrossRef]
  7. A. Halder, M. C. Paul, S. W. Harun, S. M. M. Ali, N. Saidin, S. S. A. Damanhuri, H. Ahmad, S. Das, M. Pal, and S. K. Bhadra, IEEE Photon. J. 4, 2176 (2012). [CrossRef]
  8. Y. H. Tsang, T. A. King, K. Ko, and J. Lee, J. Mod. Opt. 53, 991 (2006). [CrossRef]
  9. D. Dorosz, J. Zmojda, M. Kochanowicz, P. Miluski, and J. Dorosz, Acta Phys. Pol. A 122, 927 (2012).
  10. D. Dorosz, J. Zmojda, and M. Kochanowicz, Opt. Eng. 53, 071807 (2014). [CrossRef]
  11. P.-W. Kuan, K. Li, G. Zhang, X. Wang, L. Zhang, G. Bai, Y. Tsang, and L. Hu, Opt. Mater. Express 3, 723 (2013). [CrossRef]
  12. A. Halder, M. Paul, N. S. Shahabuddin, S. Harun, N. Saidin, S. S. A. Damanhuri, H. Ahmad, S. Das, M. Pal, and S. Bhadra, IEEE Photon. J. 4, 14 (2012). [CrossRef]
  13. D. Y. Shen, L. Pearson, P. Wang, J. K. Sahu, and W. A. Clarkson, Opt. Express 16, 11021 (2008). [CrossRef]
  14. P. Honzatko, A. Dhar, I. Kasik, O. Podrazky, V. Matejec, P. Peterka, W. Blanc, and B. Dussardier, Proc. SPIE 8306, 830608 (2011).
  15. K. Jedrzejewski, Opto-Electron. Rev. 8, 153 (2000).

Cited By

Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited