OSA's Digital Library

Spotlight on Optics

Spotlight on Optics

| HIGHLIGHTED ARTICLES FROM OSA JOURNALS

  • May 2010

Optics InfoBase > Spotlight on Optics > Seven-core multicore fiber transmissions for passive optical network


Seven-core multicore fiber transmissions for passive optical network

Published in Optics Express, Vol. 18 Issue 11, pp.11117-11122 (2010)
by B. Zhu, T. F. Taunay, M. F. Yan, J. M. Fini, M. Fishteyn, E. M. Monberg, and F. V. Dimarcello

Source article Abstract | Full Text: XHTML | Full Text: PDF


Spotlight summary: The Internet provides a global exchange of information at a level never seen before in human history. This feat would not have been possible without the huge bandwidth of optical fibers used for transmitting the information over vast distances, e.g. across the Atlantic Ocean. As more and more new applications depend on sending and receiving large amounts of data (e.g., high-resolution video), the demand for capacity in networks is growing exponentially. To maintain high bandwidth all the way to the end-user and reduce power consumption, it is necessary to avoid converting the optical signals to electrical signals before the signal reaches the end-user. This means that each end user should ideally be supplied with an optical fiber. Underground duct pipes containing optical fibers can hold only a limited number of fibers before being congested, and deploying new duct pipes is very costly. So how do we increase the number of end-users supplied with an optical fiber?

One approach is to use multicore fiber (MCF). MCF can be described as multiple optical fibers in one. Zhu and colleagues from OFS Laboratories now suggest a novel MCF design consisting of seven 8-µm-diameter cores arranged in a hexagonal array with a spacing of 38 µm. Each core can carry signals to and from 64 end-users, so 1 fiber can serve 448 end-users simultaneously. The researchers find that the transmission losses of the 6 outer cores can be slightly higher than in standard optical fibers but also show that the losses can be reduced simply by increasing the fiber cladding diameter from 130 to 140 µm.

Nothing would be gained from this advanced design if the coupling of separate signals into the individual cores of the MCF required difficult and costly alignment. However, the researchers also demonstrate a new tapered multicore fiber connector (TMC). The TMC consists of seven single core fibers tapered together to match the MCF, so that one can couple light into each core of the MCF from separate single-core fibers. The TMC is fusion spliced to a MCF by use of a commercially available splicer with automatic alignment, thereby showing that the complex design of the MCF does not hinder its practical implementation. The splice losses are even found to be similar to splice losses of conventional fibers.

The researchers further test their MCF by examining crosstalk between adjacent cores—since it is important that the signals carried in one core do not interfere with the signals carried in other cores. The power transfer between cores is measured to less than -38 and -24 dB for signals propagating at 1310 and 1490 nm, respectively.

As a powerful demonstration of the applicability of the new fiber design, the researchers built a setup with an 11.3-km-long MCF connected to TMCs at both ends. In one end, each of the 7 single core fibers were connected to optical fiber splitters, dividing the signals from each single-core into 64 optical fibers. In this way, the network can supply 448 end-users. It was demonstrated that signals can be transmitted back and forth along the MCF at 2.5 Gbit/s in each core, while still achieving practically error-free transmission.

The network architecture and components used by the OFS Laboratories group can thus allow a single optical fiber to supply each of 448 end-users with 39 Mbit/s. This is more than enough for each user to watch DVD-quality video in real time. Since the data transmission is bidirectional, one other obvious application is online conferences with high-quality video. Looking into the future, further improvements to the individual network components can lead to an additional increase in both the number of end-users and the data rate. Increasing the number of end-users per fiber lowers the implementation cost per user, thereby making it more economically viable to start the deployment of new fibers.

-- Michael Henoch Frosz



Technical Division: Optoelectronics
ToC Category: Fiber Optics and Optical Communications
OCIS Codes: (060.2310) Fiber optics and optical communications : Fiber optics
(060.2360) Fiber optics and optical communications : Fiber optics links and subsystems
(060.4510) Fiber optics and optical communications : Optical communications


Posted on May 28, 2010

Add Comment
You must log in to add comments.





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Previous Spotlights

2014

2013

2012

2011

2010

2009