OSA's Digital Library

Spotlight on Optics

Spotlight on Optics

| HIGHLIGHTED ARTICLES FROM OSA JOURNALS

  • January 2014

Optics InfoBase > Spotlight on Optics > Low-loss and low-bend-sensitivity mid-infrared guidance in a hollow-core–photonic-bandgap fiber


Low-loss and low-bend-sensitivity mid-infrared guidance in a hollow-core–photonic-bandgap fiber

Published in Optics Letters, Vol. 39 Issue 2, pp.295-298 (2014)
by Natalie V. Wheeler, Alexander M. Heidt, Naveen K. Baddela, Eric Numkam Fokoua, John R. Hayes, Seyed R. Sandoghchi, Francesco Poletti, Marco N. Petrovich, and David J. Richardson

Source article Abstract | Full Text: XHTML | Full Text: PDF


Spotlight summary: In ancient times optical science was only concerned with that particular "light" that could be seen by the human eye. Nowadays, the light spectrum that we recognize and utilize is very much extended beyond the visible. In a similar way the ability of conventional optical fibers to deliver light is limited by material properties. Although the ultra-pure silica glass used to make most optical fibers is undoubtedly the best fiber fabrication material when all desired glass characteristics are taken into account (durability, resistance, easy to handle and fabricate etc.), it can only be used for transmitting light with low attenuation levels (less than 10dB/km) for wavelengths from the visible to the near infrared (below 2 μm). Longer (or shorter) wavelengths cannot be transmitted because silica glass is no longer transparent at these other wavelengths.

However there is a way to get around this problem…

The emergence of hollow core photonic bandgap fibers (HC-PBGF) towards the end of the 20th century greatly enriched our understanding of optical waveguides and expanded the horizon of specialty optical fibers. While the basic material is still silica glass, more than 99% of the light can be efficiently guided in an air core. Wheeler and colleagues have now reported significant progress in the fabrication of low loss HC PBGF for long wavelength transmission in the mid-infrared (MIR). They have successfully reduced the lowest recorded attenuation level of HC-PBGF from 1 dB/m (reported by Urich et al. in 2012) down to 0.05 dB/m in the MIR (beyond 3 μm), by adopting a larger core size of 50 µm (a 19-cell HC-PBGF is used). This fiber exhibited a transmission window from 3.1 μm to 3.8 μm and the reported minimum loss was obtained after a purging process was used to remove HCl molecules (generated in the course of fibre fabrication) from the hollow core.

Compared with the hollow core negative curvature fibers (HC NCF) reported by Yu et al. in 2012, which have already achieved even lower loss and broader transmission window in the MIR, a key advantage of this HC-PBGF reported by Wheeler and colleagues lies in its resistance to bending losses. The authors report that, even when HC PBGF was bent in a coil of 5 cm in diameter, the bend losses of the fabricated HC-PBGF were less than 0.5dB/turn over the entire transmission spectral region and less than 0.25dB/turn over a 300 nm bandwidth. Such low bend losses allow increased flexibility and accessibility in applications such as high power laser delivery, potentially an important application area.

The authors also expect that, by enlarging the core to a 37 cell defect, the losses can be further reduced without increasing the bend sensitivity, because the reported 0.1% overlap between the guided mode and the silica cladding would decrease even further.

The combination of a relatively low attenuation and bending losses will add more flexibility and accessibility in practical applications of these silica based hollow core optical fibres in unconventional long-wavelength regimes, breaking those boundaries that have for too long limited the development of optical fiber devices and systems in the mid-infrared. This new world that is being explored may lead to unpredictable discoveries and novel applications in the field of optical sensors, optical beam delivery and optical communications.

--Walter Belardi and Fei Yu



Technical Division: Optoelectronics
ToC Category: Fiber Optics and Optical Communications
OCIS Codes: (060.2280) Fiber optics and optical communications : Fiber design and fabrication
(060.5295) Fiber optics and optical communications : Photonic crystal fibers


Posted on January 14, 2014

Add Comment
You must log in to add comments.





Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Previous Spotlights

2014

2013

2012

2011

2010

2009