OSA's Digital Library

Virtual Journal for Biomedical Optics

Virtual Journal for Biomedical Optics

| EXPLORING THE INTERFACE OF LIGHT AND BIOMEDICINE

  • Editor: Gregory W. Faris
  • Vol. 3, Iss. 3 — Mar. 31, 2008

Optics InfoBase > Virtual Journal for Biomedical Optics > Volume 3 > Issue 3 > Page 2533

« Show journal navigation

A miniaturized low-power VCM actuator for auto-focusing applications

Chien-Sheng Liu and Psang Dain Lin  »View Author Affiliations


Optics Express, Vol. 16, Issue 4, pp. 2533-2540 (2008)
http://dx.doi.org/10.1364/OE.16.002533


View Full Text Article

Acrobat PDF (296 KB)


Advanced Search

Browse Journals / Lookup Meetings

Browse by Journal and Year


   


Lookup Conference Papers

Close Browse Journals / Lookup Meetings

Article Tools

Share
Citations

Abstract

In keeping with consumer preferences for ever smaller electronic products, a requirement exists for compact, high-performance auto-focusing actuators for the camera modules deployed in cell phones. Accordingly, the present study proposes a miniaturized electromagnetic-based actuator comprising a voice coil motor (VCM) and a closed-loop position control system in which an auto-focusing capability is achieved by using a position feedback signal generated by a Hall element to dynamically adjust the position of the lens module. The experimental results show that the holding current required to maintain a lens module weighing 200 mgw in the vertical position is 17 mA ±2 mA. Compared to conventional VCM actuators deployed in cell phone camera applications, the actuator presented in this study has a smaller size (6.5 mm×6.5 mm×4 mm) and an improved power efficiency. In particular, the miniaturized actuator reduces the holding current required to maintain the lens module in the focusing position by around 75% of that required in a traditional actuator.

© 2008 Optical Society of America

1. Introduction

Focus adjustment is one of the most basic functionalities in all imaging and scanning systems, and generally requires the mechanical motion of one or more lenses or mirrors within the system [1–5

H. Ren, D. Fox, P. A. Anderson, B. Wu, and S. T. Wu, “Tunable-focus liquid lens controlled using a servo motor,” Opt. Express 14, 8031–8036 (2006). [CrossRef] [PubMed]

]. In recent years, auto-focusing camera modules have been increasingly deployed in a variety of portable electronic devices such as cell phones, personal digital assistants, laptops, and so forth. Of these devices, the mobile camera phone market has experienced a particularly strong growth, with the integration of high-end camera functions becoming commonplace even within lower- to middle-of-the-range models [6

S. M. Sohn, S. H. Yang, S. W. Kim, K. H. Baek, and W. H. Paik, “SoC design of an auto-focus driving image signal processor for mobile camera applications,” IEEE Trans. on Consumer Electronics 52, 10–16(2006). [CrossRef]

,7

C. W. Chiu, P. C. P. Chao, and D.Y. Wu, “Optimal design of magnetically actuated optical image stabilizer mechanism for cameras in mobile phones via genetic algorithm,” IEEE Trans. Magn. 43, 2582–2584 (2007). [CrossRef]

]. Generally speaking, the auto-focusing function in such cameras is achieved using a VCM actuator regulated using some form of open-loop position control mechanism. In designing these actuators, the aim is typically to improve the response, reduce the size, minimize the power consumption, and enhance the structural integrity so as to improve the resistance of the device to the wear and tear of daily use [8

S. Manabu and Y. Morimasa, “Lens drive device,” PAJ 2002-365514 (2002).

]. Of these factors, previous studies have focused primarily on improving the dynamic response of the VCM actuator [9–11

S. M. Jang, J. Y. Choi, S. H. Lee, H. W. Cho, and W. B. Jang, “Analysis and experimental verification of moving-magnet linear actuator with cylindrical Halbach array,” IEEE Trans. Magn. 40, 2068–2070 (2004). [CrossRef]

]. However, optimizing the power efficiency is also essential in order to conserve the finite battery resources of the cell phone [12

H. C. Yu, T. Y. Lee, S. K. Lin, L.T. Kuo, S. J. Wang, J. J. Ju, and D. R. Huang, “Low power consumption focusing actuator for a mini video camera,” J. Appl. Phys. , 99, 08R901 (2006). [CrossRef]

]. Accordingly, the current study presents a novel miniaturized VCM actuator for auto-focusing cell phone camera modules in which the position of the lens is dynamically adjusted in accordance with a position feedback signal provided by a Hall element. The experimental results show that compared to existing VCM actuators for cell phone devices, the proposed actuator is both smaller and more power efficient.

2. Conventional VCM actuator

Fig. 1. (a) Structure of conventional VCM actuator; (b) forces acting on conventional VCM actuator in vertical posture.

Figure 1(a) illustrates the structure of a conventional VCM actuator used in the auto-focusing camera module of a cell phone [13

M. J. Chung, “Development of compact auto focus actuator for camera phone by applying new electromagnetic configuration,” Proc. SPIE , 6048,60480J (2005). [CrossRef]

]. As shown, the fixed part of the actuator comprises two permanent magnets, a yoke and a fixed base, while the moving part, comprises a lens module, a lens-holder and a coil. In operation, the Lorentz force, FVCM , acting on the moving part of the VCM actuator is counteracted by a resistive force generated by two spring plates mounted on the upper and lower surfaces of the actuator body, respectively. As shown in Fig. 1(b), the maximum operational load occurs when the VCM actuator is located at its maximum vertical position. Under this condition, the force acting on the VCM actuator is equal to the sum of the weight Fw of the moving part of the actuator and the restoring resilience force, Fs =kδ, developed by the spring plates, where k and δ denote the spring constant of the spring plates and the vertical displacement of the moving part, respectively. According to the Lorentz law, the magnitude of FVCM is directly proportional to the intensity of the holding current I flowing in the coil. In other words, the holding current increases with an increasing displacement δ of the moving part of the actuator. For a typical commercial VCM actuator used in the auto-focusing module of a cell phone camera, the holding current required to maintain the moving part of the actuator at the maximum focusing position (corresponding to δ=0.3 mm) is around I=80 mA [14

http://www.shicoh.com/e/index.ht.

].

3. Structure of proposed actuator

Figure 2(a) illustrates the basic structure of the compact, power-efficient VCM actuator proposed in the current study. The moving part of the actuator comprises the lens module, a lens-holder and two permanent magnets (Fig. 2(b)), while the fixed part comprises a Hall element, two coils and two vertical guide rods attached to a fixed base (Fig. 2(c)). In the auto-focusing operation, a current of an appropriate intensity is passed through the coils and generates an electrical field. The interaction between this electrical field and the magnetic field induced by the permanent magnets creates an actuation force which drives the lens-holder and lens module in the upward direction. The Hall element, mounted on the side of one of the permanent magnets, senses the displacement of the moving part of the actuator and outputs an analog signal with a corresponding intensity. The analog signal is processed and an appropriate value of the coil holding current computed in order to dynamically adjust the position of the lens module such that it remains at the required focusing position. This miniaturized VCM actuator will be used in mobile camera phones. Therefore, it has to follow the Standard Mobile Imaging Architecture (SMIA standard) [15

Standard Mobile Imaging Architecture, http://www.smia-forum.org/.

].

Fig. 2. (a) Structure of proposed VCM actuator; (b) moving part; (c) fixed part.

4. Detailed design specification of miniaturized VCM actuator

Having established a basic design structure for the miniaturized VCM actuator (see Fig. 2), a series of finite element simulations were performed to determine the optimal values of the major design parameters (i.e. the dimensions, material and magnetic energy product (BH)max of the permanent magnets, the dimensions and electrical resistance of the coils, the width of the air gap between the coil and permanent magnet, and so on) required to satisfy the dual design objectives of minimizing the physical size of the device, whilst maximizing its power efficiency. Table 1 summarizes the selected values of each design parameter for the case where the lens module has a weight of 200 mgw and the moving part of the actuator has a total weight of 320 mgw. Figure 3 illustrates the numerical results obtained for the magnetic flux distribution within the proposed VCM actuator. It can be seen that the magnetic flux induced by the permanent magnets passes through the coils, and the magnetic flux distribution passing through the coils has a bilateral symmetry. Therefore, the Lorentz force FVCM acting on the movable part of the actuator is aligned in the vertical direction and prompts an upward displacement of the lens module.

Table 1.  Design parameters of proposed VCM actuator.
VariableCorresponding value
Size of VCM actuator6.5 mm×6.5 mm×4 mm
Stroke of VCM actuator0.3 mm
(BH)max of permanent magnet43~46 MGOe
Permanent magnet materialNd-Fe-B N46H
Height of permanent magnet1.6 mm
Length of permanent magnet4.1 mm
Thickness of permanent magnet0.5 mm
Height of coil3.7 mm
Length of coil5.3 mm
Thickness of coil0.4 mm
Core diameter of coil0.05 mm
Winding turns of coil132 turns
Electrical resistance of coil17.5 Ω
Air gap width0.15 mm
Fig. 3. Simulation results obtained for magnetic flux distribution in proposed VCM actuator.
Fig. 4. Simulation results obtained for variation of Lorentz force FVCM with actuator displacement as function of holding current.

Figure 4 shows the simulation results obtained for the variation of FVCM with the displacement δ for various holding currents I. It is observed that for a constant holding current, the magnitude of FVCM is essentially insensitive to the displacement δ. Furthermore, it can be seen that FVCM increases approximately linearly with an increasing holding current I. Finally, it is noted that a holding current of I=15mA is required to generate an actuation force FVCM equivalent to the weight Fw of the moving part of the actuator, i.e. 320 mgw. Figure 5 presents a schematic illustration of the electromagnetic characteristics of the VCM actuator designed in accordance with the parameter settings indicated in Table 1. It is observed that the magnetic force lines are perpendicular to the direction of the coil currents, and thus it is confirmed that the selected parameter settings optimize the power efficiency of the proposed device. Comparing Figs. 1 and 2, it is apparent that a major difference between the current device and the conventional VCM actuator is that in the current case, the displacement of the movable part is not resisted by a spring force. Accordingly, the force equilibrium equation in the vertical direction is given simply by FVCM =Fw +FN , where FN is the friction force generated between the lens holder and the two guide rods when the moving part of the actuator is displaced in the upward direction. In the ideal case where FN =0, the force equilibrium equation is given simply by FVCM =Fw . In other words, it can be inferred that: (1) the maximum actuation force FVCM required to drive the lens module to its point of maximum displacement is equal to the weight of the moving part of the actuator, i.e. Fw =320 mgw; (2) at any displacement δ, the actuator consumes the maximum power when the moving part of the system is maintained at its vertical posture; and (3) the current required to drive the moving part to the focusing position is constant and has a value of ~15 mA (see Fig. 4). Note that the absence of a spring resistive force in the proposed design reduces the power required to displace the lens holder in the vertical direction and therefore yields a significantly improved power efficiency compared to that of a conventional VCM actuator.

Fig. 5. Electromagnetic design of proposed VCM actuator: (a) two permanent magnets and coils; (b) cross-sectional view.

5. Prototype fabrication and experimental evaluation

The validity of the proposed VCM actuator was verified by constructing a laboratory-built prototype (see Fig. 6). From inspection, the device is found to have dimensions of 6.5 mm×6.5 mm×4 mm, and is therefore consistent with the specification laid down in the Standard Mobile Imaging Architecture (SMIA standard) for the critical size of auto-focusing devices in mobile phone camera modules [15

Standard Mobile Imaging Architecture, http://www.smia-forum.org/.

]. By comparison, the VCM actuators used in commercial auto-focusing cell phone camera modules have typical dimensions of 10 mm×10 mm×4.6 mm [14

http://www.shicoh.com/e/index.ht.

]. Hence, it is clear that the proposed design represents a significant size saving compared to existing auto-focusing actuator designs. The performance of the proposed device was characterized using the experimental setup shown in block diagram form in Fig. 7. During the experiments, the working voltage of 3.6 V required to power the VCM driver (equivalent to the voltage of a cell phone battery) was provided by an Agilent E3648A power supply. The I2C (inter-integrated circuit) input control command signal used to drive the VCM actuator was generated by a conventional desktop PC. During the characterization trials, the displacement of the moving part of the actuator was measured using a non-contacting laser displacement meter (Keyence, LC-2440) while the holding current was monitored using a Tektronix TCPA300 current meter.

Fig. 6. Photograph of VCM Actuator.
Fig. 7. Block diagram showing experiment setup used in characterization trials.
Fig. 8. Experimental results obtained for variation of measured holding current with actuator displacement.

The holding current was evaluated under a background noise of 0~1 mA and was sampled five times every minute. Figure 8 illustrates the variation of the holding current I with the displacement δ of the moving part of the actuator. From inspection, it is determined that the average holding current is17 mA ±2 mA. It is apparent that this value is slightly higher than the theoretical value of 15 mA (see Fig. 4). The discrepancy between the two values can be attributed to two principal factors: (1) the friction force between the lens holder and the two guiding rods is neglected in the theoretical analysis, but has a small finite value in practice, and (2) the experimental value of FVCM is generally 0~10% lower than the computed value due to manufacturing and assembly tolerances, and thus a higher value of the holding current is required to achieve the designated actuator displacement. Significantly, the results presented in Fig. 8 indicate that in the proposed VCM actuator, the holding current required to maintain the moving part of the actuator at the focusing position is around 75% of that required in a conventional VCM actuator with an open-loop control mechanism.

Fig. 9. (a) Experimental setup used for testing auto-focusing performance of proposed VCM actuator; (b) experimental results obtained without (upper) and with (lower) auto-focusing function enabled, respectively.

To assess the auto-focusing performance of the proposed actuator, a camera module comprising the laboratory-built VCM actuator prototype, an image sensor and an electric circuit was assembled and integrated with an image processing system (see Fig. 9(a)). Figure 9(b) shows two images captured with and without the auto-focusing function enabled, respectively. It is apparent that the image quality is significantly improved when the auto-focusing function is activated, thus confirming the potential of the proposed VCM actuator for commercial auto-focusing applications.

6. Conclusion

This study has presented a miniaturized low-power VCM actuator for auto-focusing applications in mobile phone camera modules. In the proposed approach, the position of the lens module is dynamically adjusted using a closed-loop position feedback mechanism driven by a signal generated by a Hall displacement detection system. The device has dimensions of 6.5 mm×6.5 mm×4 mm, and is therefore consistent with the specification laid down for auto-focusing devices in the SMIA standard [15

Standard Mobile Imaging Architecture, http://www.smia-forum.org/.

]. Moreover, the value of the holding current required to maintain the lens module in the focusing position is found to be I=(17±2) mA, which is around 75% of the holding current required in a conventional open-loop VCM actuator. Overall, therefore, the results show that the proposed device is both smaller and more power efficient than existing VCM actuators for mobile phone camera modules.

Acknowledgments

This study was supported by the Ministry of Economic Affairs of Taiwan under Grant 6327HB2220.

References and links

1.

H. Ren, D. Fox, P. A. Anderson, B. Wu, and S. T. Wu, “Tunable-focus liquid lens controlled using a servo motor,” Opt. Express 14, 8031–8036 (2006). [CrossRef] [PubMed]

2.

H. Ren and S. T. Wu, “Variable-focus liquid lens,” Opt. Express 15, 5931–5936 (2007). [CrossRef] [PubMed]

3.

C. C. Cheng, C. A. Chang, and J. A. Yeh, “Variable focus dielectric liquid droplet lens,” Opt. Express 14, 4101–4106 (2006). [CrossRef] [PubMed]

4.

K. Campbell, Y. Fainman, and A. Groisman, “Pneumatically actuated adaptive lenses with millisecond response time,” Appl. Phys. Lett. 91, 171111 (2007). [CrossRef]

5.

Seok Woo Lee and Seung S. Lee, “Focal tunable liquid lens integrated with an electromagnetic actuator,” Appl. Phys. Lett. 90, 121129 (2007). [CrossRef]

6.

S. M. Sohn, S. H. Yang, S. W. Kim, K. H. Baek, and W. H. Paik, “SoC design of an auto-focus driving image signal processor for mobile camera applications,” IEEE Trans. on Consumer Electronics 52, 10–16(2006). [CrossRef]

7.

C. W. Chiu, P. C. P. Chao, and D.Y. Wu, “Optimal design of magnetically actuated optical image stabilizer mechanism for cameras in mobile phones via genetic algorithm,” IEEE Trans. Magn. 43, 2582–2584 (2007). [CrossRef]

8.

S. Manabu and Y. Morimasa, “Lens drive device,” PAJ 2002-365514 (2002).

9.

S. M. Jang, J. Y. Choi, S. H. Lee, H. W. Cho, and W. B. Jang, “Analysis and experimental verification of moving-magnet linear actuator with cylindrical Halbach array,” IEEE Trans. Magn. 40, 2068–2070 (2004). [CrossRef]

10.

Y. Hirano and J. Naurse, “Dynamic characteristics of a voice coil motor for a high performance disk drive,” IEEE Trans. Magn. 25, 3073–3075 (1989). [CrossRef]

11.

H. C. Yu, T. Y. Lee, S. J. Wang, M. L. Lai, J. J. Ju, D. R. Huang, and S. K. Lin, “Design of a voice coil motor used in the focusing system of a digital video camera,” IEEE Trans. Magn. , 41, 3979–3981 (2005). [CrossRef]

12.

H. C. Yu, T. Y. Lee, S. K. Lin, L.T. Kuo, S. J. Wang, J. J. Ju, and D. R. Huang, “Low power consumption focusing actuator for a mini video camera,” J. Appl. Phys. , 99, 08R901 (2006). [CrossRef]

13.

M. J. Chung, “Development of compact auto focus actuator for camera phone by applying new electromagnetic configuration,” Proc. SPIE , 6048,60480J (2005). [CrossRef]

14.

http://www.shicoh.com/e/index.ht.

15.

Standard Mobile Imaging Architecture, http://www.smia-forum.org/.

OCIS Codes
(040.1490) Detectors : Cameras
(230.2090) Optical devices : Electro-optical devices
(260.5950) Physical optics : Self-focusing

ToC Category:
Imaging Systems

History
Original Manuscript: December 18, 2007
Revised Manuscript: February 3, 2008
Manuscript Accepted: February 6, 2008
Published: February 8, 2008

Virtual Issues
Vol. 3, Iss. 3 Virtual Journal for Biomedical Optics

Citation
Chien-Sheng Liu and Psang Dain Lin, "A miniaturized low-power VCM actuator for auto-focusing applications," Opt. Express 16, 2533-2540 (2008)
http://www.opticsinfobase.org/vjbo/abstract.cfm?URI=oe-16-4-2533


Sort:  Author  |  Year  |  Journal  |  Reset  

References

  1. H. Ren, D. Fox, P. A. Anderson, B. Wu, and S. T. Wu, "Tunable-focus liquid lens controlled using a servo motor," Opt. Express 14, 8031-8036 (2006). [CrossRef] [PubMed]
  2. H. Ren and S. T. Wu, "Variable-focus liquid lens," Opt. Express 15, 5931-5936 (2007). [CrossRef] [PubMed]
  3. C. C. Cheng, C. A. Chang, and J. A. Yeh, "Variable focus dielectric liquid droplet lens," Opt. Express 14, 4101-4106 (2006). [CrossRef] [PubMed]
  4. K. Campbell, Y. Fainman, and A. Groisman, "Pneumatically actuated adaptive lenses with millisecond response time," Appl. Phys. Lett. 91, 171111 (2007). [CrossRef]
  5. S. W. Lee, and S. S. Lee, "Focal tunable liquid lens integrated with an electromagnetic actuator," Appl. Phys. Lett. 90, 121129 (2007). [CrossRef]
  6. S. M. Sohn, S. H. Yang, S. W. Kim, K. H. Baek and W. H. Paik, "SoC design of an auto-focus driving image signal processor for mobile camera applications," IEEE Trans. on Consumer Electronics 52, 10-16(2006). [CrossRef]
  7. C. W. Chiu, P. C. P. Chao, and D. Y. Wu, "Optimal design of magnetically actuated optical image stabilizer mechanism for cameras in mobile phones via genetic algorithm," IEEE Trans. Magn. 43, 2582-2584 (2007). [CrossRef]
  8. S. Manabu, and Y. Morimasa, "Lens drive device," PAJ2002-365514 (2002).
  9. S. M. Jang, J. Y. Choi, S. H. Lee, H. W. Cho, and W. B. Jang, "Analysis and experimental verification of moving-magnet linear actuator with cylindrical Halbach array," IEEE Trans. Mag. 40, 2068-2070 (2004). [CrossRef]
  10. Y. Hirano and J. Naurse, "Dynamic characteristics of a voice coil motor for a high performance disk drive," IEEE Trans. Mag. 25, 3073-3075 (1989). [CrossRef]
  11. H. C. Yu, T. Y. Lee, S. J. Wang, M. L. Lai, J. J. Ju, D. R. Huang, and S. K. Lin, "Design of a voice coil motor used in the focusing system of a digital video camera," IEEE Trans. Mag.  41, 3979-3981 (2005). [CrossRef]
  12. H. C. Yu, T. Y. Lee, S. K. Lin, L.T. Kuo, S. J. Wang, J. J. Ju, and D. R. Huang, "Low power consumption focusing actuator for a mini video camera," J. Appl. Phys., 99, 08R901 (2006). [CrossRef]
  13. M. J. Chung, "Development of compact auto focus actuator for camera phone by applying new electromagnetic configuration," Proc. SPIE  6048, 60480J (2005). [CrossRef]
  14. http://www.shicoh.com/e/index.ht.
  15. Standard Mobile Imaging Architecture, http://www.smia-forum.org/.

Cited By

 Alert me when this paper is cited

OSA is able to provide readers links to articles that cite this paper by participating in CrossRef's Cited-By Linking service. CrossRef includes content from more than 3000 publishers and societies. In addition to listing OSA journal articles that cite this paper, citing articles from other participating publishers will also be listed.


« Previous Article  |  Next Article »

OSA is a member of CrossRef.

CrossCheck Deposited